Influência da configuração da célula combustível microbiana na geração de energia elétrica a partir da degradação de compostos orgânicos

Nessa pesquisa foram testadas tanto CCM com membranas e sem membranas que tinham por característica reproduzir sistemas de tratamento de esgoto sanitário. A etapa experimental desse trabalho foi dividida entre o Brasil (ensaios com CCM sem a MTP e utilizando esgoto sanitário) e Portugal (ensaios com CCM tradicionais de uma e duas câmaras, utilizando água residuária sintética e a bactéria Lactobacillus pentosus). A execução em dois locais diferentes resultou em um maior aprofundamento e desenvolvimento da pesquisa. As CCM foram avaliadas principalmente quanto ao potencial elétrico e eficiência da degradação de compostos orgânicos (esgoto sanitário e água residuária sintética). Para os dados obtidos no Brasil, as três configurações apresentaram maior diferença na potência em função do modo de operação. A operação intermitente apresentou a maior potência (11 mW/m2) para a CCM cilíndrica de fluxo ascendente, enquanto que operação continua a maior potência (4,2 mW/m2) foi obtida para a CCM retangular de fluxo horizontal, a qual também apresentava uma maior facilidade na manutenção quanto aos eletrodos (adição/remoção). A CCM cúbica de fluxo ascendente devido a sua concepção simples demandava um sistema complementar para o aumento da remoção de DQO. Apesar da baixa potência mensurada para os ensaios realizados no Brasil há de se pontuar que os mesmos foram obtidos para reatores sem membranas e utilizando o esgoto sanitário, o qual apresentou grande sazonalidade. Para a etapa realizada em Portugal, foi possível realizar quinze diferentes ensaios e mais um ensaio específico de crescimento. A maior potência (10,37 mW/m2) foi obtida para CCM de câmara dupla operada de modo contínuo para um tempo de detenção hidráulico (TDH) de 20 horas. A maior potência obtida para a CCM de câmara única foi de 5,53 mW/m2 quando houve a adição do extrato de levedura (função teórica de mediador). A potência da CCM, na maioria das vezes, esteve relacionada à proporção de sólidos voláteis e totais, SV/ST, quantidade de bactérias, pH, características de operação e por fim a configuração da CCM. O ensaio de crescimento revelou a correlação da potência em função da quantidade de bactérias inseridas da massa do biofilme (SV) e mostra-se como uma ferramenta na avaliação da potência das CCM.

Oxidação eletroquímica de etanol em temperatura ambiente e intermediária: estudo quantitativo das vias reacionais por espectrometria de massas on-line

Na primeira parte do trabalho, foram investigados materiais ativos para eletro-oxidar etanol e acetaldeído seletivos para a rota C2 (Carbono 2) e, também, ativos para eletro-oxidar hidrogênio molecular, visando a aplicação em células a combustível de hidrogênio indireto. Neste tipo de célula, um processador de combustível externo desidrogena o etanol e os produtos desta reação, contendo H2, acetaldeído e, possivelmente, etanol residual, são direcionados para alimentar o ânodo. Neste sentido, o eletrocatalisador anódico pode ser ativo para a eletro-oxidação de etanol residual, bem como acetaldeído, mas este deve catalisar a reação via C2 com o objetivo de evitar a formação de espécies que envenenam a superfície catalítica (CO ou CHx), ou seja, a ligação C-C deve permanecer intacta. Os eletrocatalisadores bimetálicos foram formados por M/Pt/C (onde M = W, Ru ou Sn) e os produtos reacionais foram analisados por DEMS On-line. Os resultados mostraram que Ru/Pt/C e Sn/Pt/C apresentaram maiores taxas de reação global, no entanto, eles não foram seletivos. Por outro lado, W2/Pt3/C foi mais seletivo para a rota C2, dada a não formação de CH4 e CO2. Além disso, este material também foi ativo e estável para a eletro-oxidação de H2, mesmo na presença de acetaldeído, o que o torna um potencial catalisador para aplicação no ânodo de células a combustível de hidrogênio indireto. Na segunda parte do trabalho, o objetivo foi relacionado com o estudo de eletrocatalisadores seletivos para a rota C1 (Carbono 1). A oxidação eletroquímica do etanol e de seus produtos reacionais foram investigados por DEMS on-line em temperatura ambiente e intermediária (245oC). Para temperatura ambiente, utilizou-se solução aquosa de ácido sulfúrico (H2SO4) e, para temperatura intermediária, utilizou-se ácido sólido (CsH2PO4) como eletrólito. Os eletrocatalisadores investigados foram formados por SnOxRuOx-Pt/C e Pt/C. Em temperatura ambiente, os resultados de polarização potenciodinâmica mostraram uma maior atividade eletrocatalítica para o material SnOxRuOx-Pt/C, com eficiência de corrente para formação de CO2 de 15,6% contra 15,2% para Pt/C, sob condições estagnantes, sem controle por transporte de massa. O stripping de resíduos reacionais, após a eletro-oxidação de etanol bulk, sob condições de fluxo, mostraram o acúmulo de espécies com 1 átomo de carbono (CO e CHx) que causam o bloqueio dos sítios ativos e são oxidadas eletroquimicamente somente em mais altos potenciais (ca. 1,0 V). Por outro lado, as curvas de polarização a 245oC mostraram maiores valores de eficiências de correntes para formação de CO2 (45% para Pt/C em ambos potenciais 0,5 V e 0,8 V contra 36% e 50% para SnOxRuOx-Pt/C em 0,5 V e 0,8 V respectivamente) quando comparado com os valores obtidos em temperatura ambiente, mas com atividades similares para SnOxRuOx-Pt/C e Pt/C. Para ambos os eletrocatalisadores, os estudos de espectrometria de massas a 245oC evidenciaram que as rotas eletroquímicas ocorrem em paralelo com rotas puramente químicas, envolvendo catálise heterogênea, de decomposição do etanol, produzindo H2 e CO2 como produtos majoritários.

Chronopotentiometric study of a Nafion membrane in presence of glucose

Chronopotentiometric and swelling experiments have been conducted to characterize the behavior of a Nafion membrane in NaCl and KCl aqueous solutions without and with glucose. A mixture solution with similar composition to the cerebrospinal fluid and blood plasma has also been studied. From the chronotentiograms, current-voltage curves have been obtained, and the values of the limiting current density, diffusion boundary layer thickness, difference between counter-ion transport number in membrane and free solution, and transition times have been determined for the investigated membrane systems. The obtained results indicate that the presence of glucose affects the ion transport through the membrane depending on the electrolyte and glucose concentrations. At low electrolyte concentration, experimental transition times are found to be smaller in presence of glucose, which has been related to an effective membrane area reduction in presence of glucose. The membrane system corresponding to the mixture solution shows a behavior similar to the single high concentration NaCl membrane system, indicating that the observed behavior is mainly associated to the Na^+ ions transport in higher proportion. In this case, the glucose presence does not affect significantly the investigated properties of the membrane, which is interesting for its utilization in a glucose fuel cell.

Electrocatalytic hydrogenation of acetophenone using a Polymer Electrolyte Membrane Electrochemical Reactor

The use of a solid polymeric electrolyte, spe, is not commonly found in organic electrosynthesis despite its inherent advantages such as the possible elimination of the electrolyte entailing simpler purification processes, a smaller sized reactor and lower energetic costs. In order to test if it were possible to use a spe in industrial organic electrosynthesis, we studied the synthesis of 1-phenylethanol through the electrochemical hydrogenation of acetophenone using Pd/C 30 wt% with different loadings as cathode and a hydrogen gas diffusion anode. A Polymer Electrolyte Membrane Electrochemical Reactor, PEMER, with a fuel cell structure was chosen to carry out electrochemical reduction with a view to simplifying an industrial scale-up of the electrochemical process. We studied the influence of current density and cathode catalyst loading on this electroorganic synthesis. Selectivity for 1-phenylethanol was around 90% with only ethylbenzene and hydrogen detected as by-products.

Real-time monitoring of electrochemically active biofilm developing behavior on bioanode by using EQCM and ATR/FTIR

In the current study, the relationship between current and biomass and bio-adhesion mechanism of electrogenic biofilm on electrode were investigated using EQCM and ATR-SEIRAS linking electrochemistry. The results indicated that cellular biomass of biofilm on QCM-crystal surface showed maximum value of 6.0 μg/cm2 in initial batch and 11.5 μg/cm2 in the second batch on mature biofilm, producing a similar maximum current density of 110 μA/μg. Especially, the optimum cell biomass linking high electricity production ratio (110 μA/μg) occurred before maximum biomass coming, implying that over-growth mature biofilm is not an optimum state for enhancing power output of MFCs. On the other hand, the spectra using ATR-SEIRAS technique linking electrochemistry obviously exhibited water structure adsorption change at early biofilm formation and meanwhile the water adsorption accompanied the adsorbed bacteria and the bound cells population on the electrode increased with time. Meanwhile, the direct contact of bacteria and electrode via outer-membrane protein can be confirmed via a series spectra shift at amide I and amide II modes and water movement from negative bands displacing by adsorbed bacteria. Our study provided supplementary information about the interaction between the microbes and electrode beyond traditional electrochemistry.

EU Policies and Cluster Developments of Hydrogen Communities. Bruges European Economic Research (BEER) Papers 14/December 2008

This study takes on the issue of political and socio-economic conditions for the hydrogen economy as part of a future low carbon society in Europe. It is subdivided into two parts. A first part reviews the current EU policy framework in view of its impact on hydrogen and fuel cell development. In the second part an analysis of the regional dynamics and possible hydrogen and fuel cell clusters is carried out. The current EU policy framework does not hinder hydrogen development. Yet it does not constitute a strong push factor either. EU energy policies have the strongest impact on hydrogen and fuel cell development even though their potential is still underexploited. Regulatory policies have a weak but positive impact on hydrogen. EU spending policies show some inconsistencies. Regions with a high activity level in HFC also are generally innovative regions. Moreover, the article points out certain industrial clusters that favours some regions' conditions for taking part in the HFC development. However, existing hydrogen infrastructure seems to play a minor role for region's engagement. An overall well-functioning regional innovation system is important in the formative phase of an HFC innovation system, but that further research is needed before qualified policy implications can be drawn. Looking ahead the current policy framework at EU level does not set clear long term signals and lacks incentives that are strong enough to facilitate high investment in and deployment of sustainable energy technologies. The likely overall effect thus seems to be too weak to enable the EU hydrogen and fuel cell deployment strategy. According to our analysis an enhanced EU policy framework pushing for sustainability in general and the development of hydrogen and fuel cells in particular requires the following: 1) A strong EU energy policy with credible long term targets; 2) better coordination of EU policies: Europe needs a common understanding of key taxation concepts (green taxation, internalisation of externalities) and a common approach for the market introduction of new energy technologies; 3) an EU cluster policy as an attempt to better coordinate and support of European regions in their efforts to further develop HFC and to set up the respective infrastructure.

Sedimentology of surface sediments from the continental shelf and slope off West Africa (Table 1)

Samples from sutface sediments of the shell, continental slope, and adjacent deep sea regions off West Africa between 27° N and 15° N were investigated with respect to grain size distribution of the total samples, sand contents of the acid insoluble residues, carbonate content of the total samples, and the separate grain size fractions, specific surfaces, colours and mineralogical composition of the clay fractions. The grain size distributions of the total samples of the sediments of the shelf and the continental slope off Spanish-Sahara are controlled mainly by biogenic components. The supply of terrigeneous material in this area is very low. At deeper parts of the continental slope and in the deep sea areas, the relative amounts of carbonate minerals in the sediments are considerably reduced. The prevailing sand contents of the upper slope changes into clay dominance. On the shelf of Mauritania - represented by profiles extending down to 200 m water depth - the grain size is also controlled mainly by biogenic carbonates. Nevertheless, the admixture of fossil silicate components is important, too. The southern parts of the area is investigated are located in a region influenced by sediments of the Senegal River, which especially control the contents of silt and clay. The silicate sands, predominately of quartz, are fossil and form a mixed sediment with younger deposits. The carbonate contents of the different grain size fractions are formed either by sedimentation of carbonate and silicate particles of the respective grain size or by autochtonous disintegration of coarser sediment particles, as shown by the occurence of Mg-rich calcite and especially aragonite in the clay sized fraction. In the northern parts of the area investigated, which have very minute terrigeneous supply, the latter mechanism is the dominant factor, controlling the carbonate contents of the fine grain sized fractions. In the vicinity of the mouth of the Senegal the carbonate contents are influenced by extremely high dilution with terrigencous silicates. Mg-rich calcite and aragonite are produced preferentially in shallow slope and shelf areas up to 500 m of water depth. The specific surfaces of the carbonate-free clay fractions indicate that the clay fractions of the shelfareas with little terrigenous supply consits of relatively coarser particles. Very fine particles are removed and transported towards the deep sea. Lateral differentiation of this kind was not observed in the area off Senegal. The high surface areas, characterizing the clay fractions of this region, are thought to be due to high montmorillonite contents as was found for deep seas sediments. The mineralogical composition of the clay fraction from the southern parts of the area is characterized by high kaolinite and montmorillonite contents, while in the northern illite is predominating. At least two types of montmorillionites are present: in areas influenced by the Senegal mostly one type was found, which could swell to 17; on the shelves and slopes of the other regions the montmorillonite-group is represented by a montmorillonite-mica-type mixed-layer mineral. A "glauconite", found in the sand fraction, which had very similar properties to those of the montmorillonite-mica mixed-layer, is believed to be the source of this mixed-layer-type mineral. Palygorskite is present in all samples out of range of the Senegal supply. It may be an indicator of eolian transported material. The occurence of rich palygorskit deposits in the arid hinterlands emphasizes the terrestrial origin.

Alexandrium cyst abundance in Nootka Sound aquaculture and towns

Senior thesis written for Oceanography 445

Parotidectomy: review of treatment and outcomes

Background: Parotidectomy is a common surgical procedure performed for a wide array of benign and malignant tumours. The aim of the present study was to review a single-institution experience with parotidectomy over a 10 year period. Methods: We retrospectively reviewed 170 patients who had parotidectomy performed. The preoperative investigations, clinicopathological parameters, perioperative morbidity and mortality were assessed. Results: One hundred and six (62%) of the patients were men. The mean age was 54 years (range 21-80). Indications for parotidectomy included benign tumour (44%), malignant tumour (42%), inflammatory parotid disease (7%) and miscellaneous (5%). The most common benign tumour was pleomorphic adenoma (25%). The most common malignant tumour was metastatic cutaneous squamous cell carcinoma (SCC) (19%). Fine needle aspiration cytology was performed in 83% patients with a sensitivity and specificity for benign tumours of 76% and 97%, respectively. The sensitivity and specificity for malignant tumours was 90% and 99%, respectively. One (0.6%) patient died in the postoperative period. Postoperative complications included wound infection (2.3%), wound haematoma (3.5%) and seroma (6.6%). Six patients (3.5%) developed temporary complete facial paresis, while 33 patients (20%) developed temporary partial facial palsy in the immediate postoperative period. The 2-year disease-free and disease-specific survival for those patients with metastatic cutaneous SCC were 75% and 76%, respectively. Conclusions: The most common indications for parotidectomy were pleomorphic adenoma and metastatic cutaneous SCC. Our perioperative morbidity and survival for patients with malignant parotid disease compare favourably with other institutional series.

Modern environmental improvement pathways for the coal power generation industry in Australia

In this work we assess the pathways for environmental improvement by the coal utilization industry for power generation in Australia. In terms of resources, our findings show that coal is a long term resource of concern as coal reserves are likely to last for the next 500 years or more. However, our analysis indicates that evaporation losses of water in power generation will approach 1000 Gl (gigalitres) per year, equivalent to a consumption of half of the Australian residential population. As Australia is the second driest continent on earth, water consumption by power generators is a resource of immediate concern with regards to sustainability. We also show that coal will continue to play a major role in energy generation in Australia and, hence, there is a need to employ new technologies that can minimize environmental impacts. The major technologies to reduce impacts to air, water and soils are addressed. Of major interest, there is a major potential for developing sequestration processes in Australia, in particular by enhanced coal bed methane (ECBM) recovery at the Bowen Basin, South Sydney Basin and Gunnedah Basin. Having said that, CO2 capture technologies require further development to support any sequestration processes in order to comply with the Kyoto Protocol. Current power generation cycles are thermodynamic limited, with 35-40% efficiencies. To move to a high efficiency cycle, it is required to change technologies of which integrated gasification combined cycle plus fuel cell is the most promising, with efficiencies expected to reach 60-65%. However, risks of moving towards an unproven technology means that power generators are likely to continue to use pulverized fuel technologies, aiming at incremental efficiency improvements (business as usual). As a big picture pathway, power generators are likely to play an increasing role in regional development; in particular EcoParks and reclaiming saline water for treatment as pressures to access fresh water supplies will significantly increase.

Heterogeneous nucleation of Mg-Al alloys

Grain size is one of the most important microstructural characteristics determining the mechanical properties and therefore the service performance of polycrystalline materials. Heterogeneous nucleation involves the addition or in situ formation of potent nuclei in the system to promote nucleation events, leading to a fine grain structure. This paper reports experimental results using graphite and SiC as potential grain refining agents to form in situ nuclei for Mg in Mg-Al alloys, and demonstrates the key role of Al4C3 in grain refilling this important alloy system. This insight will contribute to the design and development of the most cost effective, eco-friendly grain refining agents for Mg-Al alloys. (c) 2006 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Synthesis and characterization of turbostratic carbons prepared by catalytic chemical vapour decomposition of acetylene

The turbostratic mesoporous carbon blacks were prepared by catalytic chemical vapour decomposition (CCVD) of acetylene using Ni/MgO catalysts prepared by co-precipitation. The relationship between deposition conditions and the nanostructures of resultant carbon black materials was investigated. It was found that the turbostratic and textural structures of carbon blacks are dependent on the deposition temperature and nickel catalyst loading. Higher deposition temperature increases the carbon crystallite unit volume V-nano and reduces the surface area of carbon samples. Moreover, a smaller V-nano is produced by a higher Ni loading at the same deposition temperature. In addition of the pore structure and the active metal surface area of the catalyst, the graphitic degree or electronic conductivity of the carbon support is also a key issue to the activity of the supported catalyst. V-nano is a very useful parameter to describe the effect of the crystalline structure of carbon blacks on the reactivity of carbon blacks in oxygen-carbon reaction and the catalytic activity of carbon-supported catalyst in ammonia decomposition semi-quantitatively. (C) 2006 Elsevier B.V. All rights reserved.

Modeling hydrogen separation in high temperature silica membrane systems

In this work, a working model is proposed of molecular sieve silica (MSS) multistage membrane systems for CO cleanup at high temperatures (up to 500 degrees C) in a simulated fuel cell fuel processing system. Gases are described as having little interactions with each other relative to the pore walls due to low isosteric heat of adsorption on silica surfaces and high temperatures. The Arrhenius function for activated transport of pure gases was used to predict mixture concentration in the permeate and retentate streams. Simulation predicted CO could be reduced to levels below the required 50 ppmv for polymer electrolyte membrane fuel cell anodes at a stage H-2/CO selectivity of higher than 40 in 4 series membrane units. Experimental validation showed predicting mixture concentrations required only pure gas permeation data. This model has significant application for setting industrial stretch targets and as a robust basis for complex membrane model configurations. (c) 2006 American Institute of Chemical Engineers.

Engineering access control for distributed enterprise applications

Access control (AC) is a necessary defense against a large variety of security attacks on the resources of distributed enterprise applications. However, to be effective, AC in some application domains has to be fine-grain, support the use of application-specific factors in authorization decisions, as well as consistently and reliably enforce organization-wide authorization policies across enterprise applications. Because the existing middleware technologies do not provide a complete solution, application developers resort to embedding AC functionality in application systems. This coupling of AC functionality with application logic causes significant problems including tremendously difficult, costly and error prone development, integration, and overall ownership of application software. The way AC for application systems is engineered needs to be changed. ^ In this dissertation, we propose an architectural approach for engineering AC mechanisms to address the above problems. First, we develop a framework for implementing the role-based access control (RBAC) model using AC mechanisms provided by CORBA Security. For those application domains where the granularity of CORBA controls and the expressiveness of RBAC model suffice, our framework addresses the stated problem. ^ In the second and main part of our approach, we propose an architecture for an authorization service, RAD, to address the problem of controlling access to distributed application resources, when the granularity and support for complex policies by middleware AC mechanisms are inadequate. Applying this architecture, we developed a CORBA-based application authorization service (CAAS). Using CAAS, we studied the main properties of the architecture and showed how they can be substantiated by employing CORBA and Java technologies. Our approach enables a wide-ranging solution for controlling the resources of distributed enterprise applications. ^

High pressure and low temperature study of ammonia borane and lithium amidoborane

Hydrogen has been considered as a potentially efficient and environmentally friendly alternative energy solution. However, one of the most important scientific and technical challenges that the "hydrogen economy" faces is the development of safe and economically viable on-board hydrogen storage for fuel cell applications, especially to the transportation sector. Ammonia borane (BH3NH 3), a solid state hydrogen storage material, possesses exceptionally high hydrogen content (19.6 wt%).However, a fairly high temperature is required to release all the hydrogen atoms, along with the emission of toxic borazine. Recently research interests are focusing on the improvement of H2 discharge from ammonia borane (AB) including lowering the dehydrogenation temperature and enhancing hydrogen release rate using different techniques. Till now the detailed information about the bonding characteristics of AB is not sufficient to understand details about its phases and structures. ^ Elemental substitution of ammonia borane produces metal amidoboranes. Introduction of metal atoms to the ammonia borane structure may alter the bonding characteristics. Lithium amidoborane is synthesized by ball milling of ammonia borane and lithium hydride. High pressure study of molecular crystal provides unique insight into the intermolecular bonding forces and phase stability. During this dissertation, Raman spectroscopic study of lithium amidoborane has been carried out at high pressure in a diamond anvil cell. It has been identified that there is no dihydrogen bond in the lithium amidoborane structure, whereas dihydrogen bond is the characteristic bond of the parent compound ammonia borane. It has also been identified that the B-H bond becomes weaker, whereas B-N and N-H bonds become stronger than those in the parent compound ammonia borane. At high pressure up to 15 GPa, Raman spectroscopic study indicates two phase transformations of lithium amidoborane, whereas synchrotron X-ray diffraction data indicates only one phase transformation of this material. ^ Pressure and temperature has a significant effect on the structural stability of ammonia borane. This dissertation explored the phase transformation behavior of ammonia borane at high pressure and low temperature using in situ Raman spectroscopy. The P-T phase boundary between the tetragonal (I4mm) and orthorhombic (Pmn21) phases of ammonia borane has been determined. The transition has a positive Clapeyron slope which indicates the transition is of exothermic in nature. Influence of nanoconfinemment on the I4mm to Pmn2 1 phase transition of ammonia borane was also investigated. Mesoporus silica scaffolds SBA-15 with pore size of ~8 nm and MCM-41 with pore size of 2.1-2.7 nm, were used to nanoconfine ammonia borane. During cooling down, the I4mm to Pmn21 phase transition was not observed in MCM-41 nanoconfined ammonia borane, whereas the SBA-15 nanocondfined ammonia borane shows the phase transition at ~195 K. Four new phases of ammonia borane were also identified at high pressure up to 15 GPa and low temperature down to 90 K.^