Experimental formulation of an anti fouling paint with tributyl tin oxide as toxic pigment

Results of the experimental formulation of an antifouling paint incorporating TBTO as toxic pigment are presented in this paper. Of the various resins tested, namely, phenolic, cashew nut shell liquid (CNSL), epoxy linseed oil with rosin and limed rosin, the paint composition with limed rosin gave the critical leaching rate of TBTO. Acid alkali test showed dissolution of matrix and visible migration of toxin to the surface. Accelerated corrosion tests had not recorded any signs of corrosion in panels painted with or without barrier coat. Raft exposure studies indicated that the new formulation could resist fouling accumulation on painted panels for 9 months.

Innovative fabrication of PZT pillar arrays by a colloidal approach

An innovative approach for fabricating pillar arrays for ultrasonic transducer applications is disclosed. It involves the preparation of concentrated piezoelectric lead zirconate titanate (PZT) suspensions in aqueous solutions of epoxy resin and its polymerization upon adding a polyamine based hardener. Zeta potential and rheological measurements revealed that 1wt.% dispersant, 20wt.% of epoxy resin and a hardener/epoxy resin ratio of 0.275mLg -1, were the optimized contents to obtain strong PZT samples with high green strength (35.21±0.39MPa). Excellent ellipsoidal and semi-circle shaped pillar arrays presenting lateral dimensions lower than 10μm and 100μm height were successfully achieved. The organics burning off was conducted at 500°C for 2h at a heating rate of 1°Cmin -1. Sintering was then carried out in the same heating cycle at 1200°C for 1h. The microstructures of the green and sintered ceramics were homogeneous and no large defects could be detected. © 2011 Elsevier Ltd.

Dynamic compressive response of composite square honeycombs

Carbon fibre-epoxy composite square honeycombs, and the parent composite material, were tested in quasi-static compression at a strain rate of 10 -3 s -1 and in dynamic compression at strain rates of 10 3-10 4 s -1 using an instrumented Kolsky bar arrangement. Taken together, these tests provide an assessment of the potential of this composite topology for use as a lightweight sandwich core. The honeycombs had two relative densities, 0.12 and 0.24, and two material orientations, ±45° and 0/90° with respect to the prismatic, loading direction of the honeycomb. Honeycomb manufacture was by slotting, assembling and bonding together carbon fibre/epoxy woven plies of composite sheets of 2 × 2 twill weave construction. The peak value of wall stress in the honeycombs was about one third that of the parent material, for all strain rates. An elastic finite element analysis was used to trace the source of this knock-down in strength: a stress concentration exists at the root of the slots and leads to premature failure by microbuckling. Shock-wave effects were evident at impact velocities exceeding 50 ms -1 for the honeycomb of relative density 0.12. This was traced to stubbing of the buckled cell walls against the face of the Kolsky bar. © 2011 Elsevier Ltd. All rights reserved.

Microfabrication of electrode patterns for high-frequency ultrasound transducer arrays.

High-frequency ultrasound is needed for medical imaging with high spatial resolution. A key issue in the development of ultrasound imaging arrays to operate at high frequencies (≥30 MHz) is the need for photolithographic patterning of array electrodes. To achieve this directly on 1-3 piezocomposite, the material requires not only planar, parallel, and smooth surfaces, but also an epoxy composite filler that is resistant to chemicals, heat, and vacuum. This paper reports, first, on the surface finishing of 1-3 piezocomposite materials by lapping and polishing. Excellent surface flatness has been obtained, with an average surface roughness of materials as low as 3 nm and step heights between ceramic/polymer of ∼80 nm. Subsequently, high-frequency array elements were patterned directly on top of these surfaces using a photolithography process. A 30-MHz linear array electrode pattern with 50-μm element pitch has been patterned on the lapped and polished surface of a high-frequency 1-3 piezocomposite. Excellent electrode edge definition and electrical contact to the composite were obtained. The composite has been lapped to a final thickness of ∼55 μm. Good adhesion of electrodes on the piezocomposite has been achieved and electrical impedance measurements have demonstrated their basic functionality. The array was then packaged, and acoustic pulse-echo measurements were performed. These results demonstrate that direct patterning of electrodes by photolithography on 1-3 piezocomposite is feasible for fabrication of high-frequency ultrasound arrays. Furthermore, this method is more conducive to mass production than other reported array fabrication techniques.

Application of gel-casting to the fabrication of 1-3 piezoelectric ceramic-polymer composites for high-frequency ultrasound devices

A modified gel-casting technique was used to fabricate a 1-3 piezoelectric ceramic/polymer composite substrate formed by irregular-shaped pillar arrays of small dimensions and kerfs. This technique involves the polymerization of aqueous piezoelectric (PZT) suspensions with added water-soluble epoxy resin and polyamine-based hardener that lead to high strength, high density and resilient ceramic bodies. Soft micromoulding was used to shape the ceramic segments, and micropillars with lateral features down to 4 m and height-to-width aspect ratios of ∼10 were achieved. The composite exhibited a clear thickness resonance mode at approximately 70 MHz and a k eff ∼ 0.51, demonstrating that the ceramic micropillars possess good electrical properties. Furthermore, gel-casting allows the fabrication of ceramic structures with non-conventional shapes; hence, device design is not limited by the standard fabrication methods. This is of particular benefit for high-frequency transducers where the critical design dimensions are reduced. © 2012 IOP Publishing Ltd.

Multi-hit armour characterisation of metal-composite bi-layers

The ballistic performance of equi-mass plates made from (i) stainless steel (SS); (ii) carbon fibre/epoxy (CF) laminate and (iii) a hybrid plate of both materials has been characterised for a spherical steel projectile. The hybrid plate was orientated with steel on the impact face (SSCF) and on the distal face (CFSS). The penetration velocity (V 50) was highest for the SS plate and lowest for the CF plate. A series of double impact tests were performed, with an initial velocity V I and a subsequent velocity V II at the same impact site. An interaction diagram in (V I,V II) space was constructed to delineate penetration from survival under both impacts. The degree of interaction between the two impact events was greater for the CFSS plate than for the SSCF plate, implying that the distal face has the major effect upon the degree of interaction.

Compressive response of glass fiber composite sandwich structures

Sandwich panels with crushable foam cores have attracted significant interest for impulsive load mitigation. We describe a method for making a lightweight, energy absorbing, glass fiber composite sandwich structure and explore it is through thickness (out-of-plane) compressive response. The sandwich structure utilized corrugated composite cores constructed from delamination resistant 3D woven E-glass fiber textiles folded over triangular cross section prismatic closed cell, PVC foam inserts. The corrugated structure was stitched to 3D woven S2-glass fiber face sheets and infiltrated with a rubber toughened, impact resistant epoxy. The quasi-static compressive stress-strain response of the panels was experimentally investigated as a function of the strut width to length ratio and compared to micromechanical predictions. Slender struts failed by elastic (Euler) buckling which transitioned to plastic microbuckling as the strut aspect ratio increased. Good agreement was observed between experimental results and micromechanical predictions over the wide range of core densities investigated in the study.

Analytical model and experimental validation of friction laws for composites under low loads

In order to account for interfacial friction of composite materials, an analytical model based on contact geometry and local friction is proposed. A contact area includes several types of microcontacts depending on reinforcement materials and their shape. A proportion between these areas is defined by in-plane contact geometry. The model applied to a fibre-reinforced composite results in the dependence of friction on surface fibre fraction and local friction coefficients. To validate this analytical model, an experimental study on carbon fibrereinforced epoxy composites under low normal pressure was performed. The effects of fibre volume fraction and fibre orientation were studied, discussed and compared with analytical model results. © Springer Science+Business Media, LLC 2012.

Age-related changes in mouse bone permeability.

The determination of lacunar-canalicular permeability is essential for understanding local fluid flow in bone, which may indicate how bone senses changes in the mechanical environment to regulate mechano-adaptation. The estimates of lacunar-canalicular permeability found in the literature vary by up to eight orders of magnitude, and age-related permeability changes have not been measured in non-osteonal mouse bone. The objective of this study is to use a poroelastic approach based on nanoindentation data to characterize lacunar-canalicular permeability in murine bone as a function of age. Nine wild type C57BL/6 mice of different ages (2, 7 and 12 months) were used. Three tibiae from each age group were embedded in epoxy resin, cut in half and indented in the longitudinal direction in the mid-cortex using two spherical fluid indenter tips (R=238 μm and 500 μm). Results suggest that the lacunar-canalicular intrinsic permeability of mouse bone decreases from 2 to 7 months, with no significant changes from 7 to 12 months. The large indenter tip imposed larger contact sizes and sampled larger ranges of permeabilities, particularly for the old bone. This age-related difference in the distribution was not seen for indents with the smaller radius tip. We conclude that the small tip effectively measured lacunar-canalicular permeability, while larger tip indents were influenced by vascular permeability. Exploring the age-related changes in permeability of bone measured by nanoindentation will lead to a better understanding of the role of fluid flow in mechano-transduction. This understanding may help indicate alterations in bone adaptation and remodeling.

Hybrid core carbon fiber composite sandwich panels: Fabrication and mechanical response

Carbon fiber reinforced polymer (CFRP) composite sandwich panels with hybrid foam filled CFRP pyramidal lattice cores have been assembled from a carbon fiber braided net, 3D woven face sheets and various polymeric foams, and infused with an epoxy resin using a vacuum assisted resin transfer process. Sandwich panels with a fixed CFRP truss mass have been fabricated using a variety of closed cell polymer and syntactic foams, resulting in core densities ranging from 44-482kgm-3. The through thickness and in-plane shear modulus and strength of the cores increased with increasing foam density. The use of low compressive strength foams within the core was found to result in a significant reduction in the compressive strength contributed by the CFRP trusses. X-ray tomography led to the discovery that the trusses develop an elliptical cross-section shape during pressure assisted resin transfer. The ellipticity of the truss cross-sections increased, and the lattice contribution to the core strength decreased as the foam density was reduced. Micromechanical modeling was used to investigate the relationships between the mechanical properties and volume fractions of the core materials and truss topology of the hybrid core. The specific strength and moduli of the hybrid cores lay between those of the CFRP lattices and foams used to fabricate them. However, their volumetric and gravimetric energy absorptions significantly exceeded those of the materials from which they were fabricated. They compare favorably with other lightweight energy absorbing materials and structures. © 2013.

Age-related changes in mouse bone permeability

The determination of lacunar-canalicular permeability is essential for understanding local fluid flow in bone, which may indicate how bone senses changes in the mechanical environment to regulate mechano-adaptation. The estimates of lacunar-canalicular permeability found in the literature vary by up to eight orders of magnitude, and age-related permeability changes have not been measured in non-osteonal mouse bone. The objective of this study is to use a poroelastic approach based on nanoindentation data to characterize lacunar-canalicular permeability in murine bone as a function of age. Nine wild type C57BL/6 mice of different ages (2, 7 and 12 months) were used. Three tibiae from each age group were embedded in epoxy resin, cut in half and indented in the longitudinal direction in the mid-cortex using two spherical fluid indenter tips (R=238 μm and 500 μm). Results suggest that the lacunar-canalicular intrinsic permeability of mouse bone decreases from 2 to 7 months, with no significant changes from 7 to 12 months. The large indenter tip imposed larger contact sizes and sampled larger ranges of permeabilities, particularly for the old bone. This age-related difference in the distribution was not seen for indents with the smaller radius tip. We conclude that the small tip effectively measured lacunar-canalicular permeability, while larger tip indents were influenced by vascular permeability. Exploring the age-related changes in permeability of bone measured by nanoindentation will lead to a better understanding of the role of fluid flow in mechano-transduction. This understanding may help indicate alterations in bone adaptation and remodeling. © 2013 Elsevier Ltd.

PBT和PBS及其共混物结晶行为和力学性能的研究

聚对苯二甲酸丁二醇酯(PBT)是一种多用途的工程塑料。本文中，主要研究了PBT/Epoxy(E)合金及PBT/ABS-g-GMA/E合金的结晶行为和力学性能。 使用示差扫描量热法对PBT/Epoxy合金的等温结晶过程进行了研究。发现PBT和E03 609环氧树脂在所研究的组成范围内完全相容。环氧树脂起到异相成核剂的作用，使PBT产生更强的瞬间结晶三维生长趋势。PBT和环氧树脂的Flory相互作用参数为负值，说明PBT和环氧树脂形成了热力学上的稳定混合物。 使用几种方法对PBT/Epoxy合金的非等温结晶过程进行了研究，Ozawa方程不能充分描述PBT/Epoxy合金的非等温结晶过程；使用莫志深等人提出的方法，成功地描述了该过程。实验结果显示1％环氧树脂可使PBT/Epoxy合金结晶速率明显增加。 对PBT/Epoxy合金的热和力学性能进行了研究。1％环氧树脂的加入提高PBT/Epoxy合金的缺口冲击强度20%；从红外光谱分析，环氧树脂与PBT发生了相互作用；环氧树脂影响了PBT/Epoxy合金的力学性质和结晶行为。 采用乳液聚合技术将甲基丙烯酸环氧丙酯(GMA)引入到ABS的壳层，合成了环氧官能化的ABS共聚物(ABS-g-GMA)，将环氧树脂加入到PBT/ABS-g-GMA合金中，利用环氧官能团与PBT端羧基/羟基的反应达到增容PBT/ABS合金的目的。当环氧树脂的含量为5％时，PBT/ABS-g-GMA/E共混物比PBT/ABS-g-GMA共混物有更优异的力学性质。 研究了聚亚丙基碳酸酯(PPC)和聚丁二酸二甲酯(PBS)共混物的相容性、结晶和力学性能。结果显示组份PPC/PBS（90/10）可能产生部分相容。采用偏光显微镜观察了PPC/PBS共混物的形态，对于90/10 PPC/PBS共混物，发现很大数量的PBS小球晶分散在PPC基质中。力学结果显示90/10 PPC/PBS共混物拉伸强度比纯PPC提高了30％，冲击强度提高了11％。

唐古特瑞香和大果大戟的化学成分研究

本学位论文由两部分共3章组成。第一部分分别报道2种藏药唐古特瑞香和大果大戟化学成分的研究成果，从2种药用植物共分离鉴定了60个不同的化合物，其中12个为新结构，特别有意义的是发现了2个具有同一新骨架的二萜化合物。第二部分概述了大戟科植物多环二萜的研究进展。 第一部分包括第1和2章。在这2章中分别报道了唐古特瑞香（Daphne tangutica Maxim）和大果大戟（Euphorbia wallichii Hook. f. Fl）化学成分的分离纯化与结构鉴定。实验采用正、反相硅胶柱层析、薄层制备及HPLC等分离方法，从唐古特瑞香的根皮中共分离出32个化合物，通过红外、质谱及核磁共振等波谱方法鉴定了其中的31个，结构类型分别属于瑞香二萜类、木脂素类、香豆素类、苯丙素类及甾体类，其中有三个新的瑞香二萜型化合物，经波谱分析将它们的结构分别鉴定为1,2a-二氢-20-棕榈酰瑞香毒素、1,2a-二氢-5b-羟基-6a,7a-环氧-树脂大戟醇-14-苯甲酸酯及1,2b-二氢-5b-羟基-6a,7a-环氧-树脂大戟醇-14-苯甲酸酯，另外还有13个已知化合物为首次从该植物中分离得到。从大果大戟的根部共分离出33个化合物，鉴定了其中的30个，其主要成分为种类丰富的二萜，包括巨大戟烷型、续随子烷型、对映－阿替生烷型、对映－贝壳杉烷型、对映－松香烷型、ent-trachylobane型、对映－异海松烷型及一新骨架五环二萜ent-wallichane型，另外还有香豆素、甾体、三萜和一些简单的小分子化合物。其中新化合物有9个，经波谱分析将它们的结构分别鉴定为5-O-(2E,4E,6E)-癸三烯酰基-3,20-O-二乙酰基巨大戟醇、5-O-(2E,4Z)-癸二烯酰基-3-O-乙酰基-20-去氧巨大戟醇、3-O-(2E,4Z)-癸二烯酰基-5b,6b-氧-交京大戟醇、7-苯甲酰氧基-3,5,15-三乙酰基-续随子醇、ent-trachylobane-3-one-17-oic-acid、3α-羟基-对映-阿替斯-16-烯-14-酮、3α,6-二羟基-对映-异海松-7-烯-2,15-二酮、wallichanol A 和 wallichanol B，其中，wallichanol A 和 wallichanol B属于一新骨架类型的五环二萜。除此以外，另有13个已知化合物为首次从该植物中分离得到。 第2部分即第3章，首次概述了大戟属植物中多环二萜的化学和药理研究进展。 This dissertation is composed by two parts. The first part reports the phytochemical investigation of two Tibetan medicine plants, Daphne tangutica Maxim and Euphorbia wallichii Hook. f. Fl. Sixty different compounds including ten new compounds and two novel diterpenoids possessing a new carbon skeleton were isolated and identified. The second part is a review about the progress of studies on the polycyclic diterpeniods of the plant family of Euphorbia. The first part consists two chapters, which expatiate on the isolation and identification of chemical constituents from D. tangutica and E. wallichii. Thirty-one compounds were isolated from the root barks of D. tangutica by methods of column chromatography (silica gel, including reversed phase), preparative TLC and HPLC, and their structure were identified as nine daphnane diterpenes, six lignans, nine cumarin derivatives, five phenylpropanoid derivatives, a steroids and a benzoate on the basis of spectroscopic methods including IR, MS and NMR. Among them, three are new diterpenes with skeleton of daphnane and the structure were determined as 1,a-dihydro-20-palimoyl-daphnetoxin, 1,2a-dihydro-5b- hydroxy-6a,7a-epoxy-resiniferonol-14-benzoate and 1,2b-dihydro-5b-hydroxy- 6a,7a-epoxy-resiniferonol-14-benzoate. In addition, thirteen known ones were isolated from this plant for the first time. Isolation of the roots of E. wallichii yielded thirty compounds, twenty-four of them were elucidated as diterpenoids, which belong to different skeleton types of ingenol, lathyrane, ent-atisane, ent-kaurane, ent-abietane, ent-trachylobane, ent-isopimarane and a new pentacyclic skeleton ent-wallichane respectively. The remains including a cumarine, a triterpenoid, a steroid and three compounds with small molecule. Nine new compounds were characterized as 5-O-deca-2E,4E,6E- trienoyl-3,20-O-diacetylingenol, 5-O-deca-2E,4Z-dienoyl-3-O-acetyl-20- deoxyingenol, 3-O-deca-2E,4Z-dienoyl-jolkinol-5b,6b-oxide, 7-benzoyl-3,5,15- triacetyl-7-hydroxylathyrol, ent-trachylobane-3-one-17-oic-acid, 3α-hydroxy-ent- atis-16-en-14-one, 3α,6-dihydroxy-ent-isopimarane-7-en-2,15-dione, wallichanol A and wallichanol B, respectively, by means of comprehensive spectroscopic analysis. Among them, wallichanol A and wallichanol B were two notable novel pentacyclic diterpenoids processing a new rearranged carbon skeleton. And more, thirteen ones were firstly reported from this plant. The third chapter summarizes the research development on chemistry and pharmacology of polycyclic diterpenes from the plant family of Euphorbia for the first time.

丁香和升麻的化学成分研究

本论文由三部分共四章组成。第一部分介绍丁香化学成分的研究成果，第二部分为升麻的化学成分研究，第三部分综述了环菠萝蜜烷三萜结构和活性关系的研究现状。 第一部分包括第一和第二章。第一章介绍了丁香（Eugenia caryophyllataThunb.）花蕾的化学成分和结构鉴定。采用正、反相硅胶柱层析等各种分离方法，从其乙醇提取物的乙酸乙酯萃取物和正丁醇萃取物中共分离出34 个化合物，它们的结构类型分属黄酮、三萜、鞣质等。其中1 个为新的酚苷类化合物，其结构经波谱分析鉴定为2-O-(6'-O-没食子酰基)-b-D-葡萄糖基苯甲酸甲酯（24），另外还有12 个化合物为首次从该植物中分离得到。第二章介绍了丁香挥发油的气相色谱- 质谱联用（ GC-MS ）和正丁醇萃取物的高效液相色谱- 质谱联用（HPLC-MS/MS）分析，尝试简单快速地检测丁香挥发油及极性部分的主要化学成分的方法。 第二部分为第三章。本章介绍了传统中药升麻（Cimicifuga foetida L.）根部乙醇提取物化学成分的分离纯化和结构鉴定。通过正、反相硅胶柱层析等分离纯化方法和MS、NMR 等波谱解析技术，共分离鉴定了20 个化合物，主要为环菠萝蜜烷三萜，其中5 个新三萜化合物分别鉴定为cimicidol-3-one（38）、3'-O-乙酰基升麻苷H-1（41）、2'-O-乙酰基升麻苷H-1（42）、(3b,12b,16b)-12-乙酰氧-16,23-环氧-9,19-环羊毛甾烷-22-烯-24-酮3-O-b-D-吡喃木糖苷（44）和升麻碱（54）。新化合物54 为结构新颖的环菠萝蜜烷三萜皂苷生物碱，这是首个发现的具有环菠萝蜜烷三萜骨架的生物碱，也是从升麻属植物中发现的第一个三萜生物碱，它的结构通过多种波谱解析，特别是2D-NMR 的充分应用，并结合化学降解和反应得到证实。此外，还介绍了分离得到的一种具有明显抑制破骨细胞活性的化合物(QS29)的体外活性研究。 第三部分即第四章，综述了升麻属植物中环菠萝蜜烷三萜与其生物活性的构效关系研究现状。 This dissertation consists of three parts. In the first and the second parts, thechemical constituents from the flower buds of Eugenia caryophyllata and therhizomes of Cimicifuga foetida were reported. The third part is a review on astructure-activity relationship of the cycloartane triterpenoid from Cimicifuga species. The first part is composed of two chapters. The chapter 1 is about the isolationand identification of the chemical constituents from the flower buds of E.caryophyllata. A new phenolic glucoside gallate, methyl 2-O-(6’-O-galloyl)-b-D-glucopyranosylbenzoate (24), together with thirty-three known compounds has beenisolated from the ethanol extract of the flower buds of E. caryophyllata throughrepeated column chromatography on normal and reversed phase silica gel. Thestructure of the new compound was elucidated on the basis of spectral and chemicalevidence. Those kno wn compounds were belonged to flavone, triterpenoid, tannin andsome simple compounds. Among them, 12 compounds were isolated from the titleplant for the first time. The second chapter describes the capillary GC-MS analysis ofthe volatile components and the HPLC-MS/MS analysis of the polar constituents fromthe flower buds of E. caryophyllata, in order to detect the main constituents in thecrude extract rapidly and precisely. The third chapter is about the chemical constituents of the rhizomes C. foetida, atraditional Chinese medicine which was used as anti-inflammatory, analgesic andantipyretic agents. Our investigation of the bioactivities constituents of the rhizomesof C. foetida led to the isolation of five new cycloartane triterpenoids, which werecharacterized as cimicidol-3-one (38), 3'-O-acetyl cimicifugoside H-1 (41),2'-O-acetyl cimicifugoside H-1 (42), (3b,12b,16b)-12-acetoxy-16,23-epoxy-9,19-cyclolanost-22-ene-24-one 3-O-b-D-xylopyranoside (44) and cimicifugadine (54),along with fifteen known compounds through repeated column chromatography onnormal and reversed phase silica gel. Among them, 54 is a novel cycloartanealkaloid and first discovered as a new type alkaoid from nature. The structures ofthese compounds were elucidated on the basis of spectral and chemical evidence, andcimicidol-3-one was confirmed by X-ray crystallography analysis. Moreover, onecompound exhibited strong anti-osteoporosis activity in vitro experiment. The fourth part is a review on a structure-activity relationship analysis of thecycloartane triterpenoid from Cimicifuga species.

低极性化合物的电喷雾质谱检测方法及几种中藏药材的活性成分研究

本学位论文首先报道了为解决低极性化合物的电喷雾质谱（ESI-MS）分析难题而建立的一种衍生化分析方法；然后从色谱-质谱联用分析、分离纯化和结构鉴定等方面分别报道了几种中藏药材的活性成分研究。论文由下述六章组成： 第一章报道了盐酸羟胺衍生化方法在电喷雾质谱 (ESI-MS) 分析中的应用。该方法利用盐酸羟胺和羰基成肟的快速反应，建立了针对三萜酮等含酮或醛羰基低极性化合物的ESI-MS 信号增强技术。此方法不仅可应用于增强羰基化合物的ESI-MS 质谱信号，还可检测化合物中羰基的个数以及辨别涉及羰基官能团的同分异构体。此外，通过简单的氧化反应，还可将该方法拓展到三萜醇、甾醇等含羟基的低极性化合物，增强它们的ESI-MS 信号。对比已报道的相关ESI-MS 增强质谱信号的衍生化方法，此方法有经济、实用、快速和简便的显著特点。 第二章是关于野生羌活及其栽培品种化学成分的色谱-质谱联用分析。对不同产地野生羌活生长过程中活性成分的动态变化、野生羌活不同形态部位和人工栽培羌活中的活性成分含量进行了HPLC 定量分析。结果表明主要活性成分羌活醇和异欧前胡素都随生长期存在规律性变化，羌活不同形态部位中的活性成分含量也有明显不同。这些实验结果有些较好地印证了传统中医的用药理论，有些也对羌活的传统使用方法提出了新的建议。 第三章介绍了几种传统中藏药材的色谱-质谱联用及串联质谱分析。通过GC-MS 方法，从藏药材长花党参挥发油中共分离鉴定出45 个化合物；利用HPLC方法测定了该藏药材中的主要化学成分——木犀草素的含量（0.7%）；利用串联质谱技术，对西番莲和射干中的主要成分进行了快速鉴定，从西番莲中鉴定了4个黄酮碳苷；从不同产地的射干和川射干中鉴定了8 个主要异黄酮成分，其中包括一个未见报道的化合物。 第四章的内容为藏药材石莲叶点地梅的活性成分研究。从植物石莲叶点地梅(Androsace integra (Maxim.) Hand.-Mazz.) 乙醇提取物的正丁醇萃取部分共分离和鉴定了6 个化合物，利用MS 和NMR 等现代波谱学技术阐明了它们的结构：其中包括4 个三萜类化合物：分别是androsacin (1)、 ardisiacrispin A (2) 、saxifragifolin A (3) 和20(29)-lupen-3-one (4)；一个神经酰胺：4-羟基-Δ8,9(Z)-鞘氨醇-2'-羟基正二十四碳酸酰胺(5)；一个甾体类化合物：胡萝卜苷(6)。化合物1为新的13,28-epoxy-oleanane 型三萜皂苷，在其结构表征的过程中，采用LC-MS 进行糖分析，获得了值得推广的好结果。通过活性筛选发现化合物1~3 对HepG2肝癌细胞表现出不同程度的抑制活性，其中化合物2 活性最好，其IG50 为1.65μg/mL。 第五章是关于一些传统中藏药材的农药活性筛选。利用Syngenta 公司的活性筛选平台对68 种传统中藏药材醇提物进行了抗菌和除草的生物源农药活性筛选。结果表明所筛选的68 种植物提取物中，共有14 种样品表现出明显的除草/杀虫活性，其中水母雪莲花、松萝和茯神木等植物提取物还具有多种生物活性。活性成分还有待进一步追踪分离、纯化和结构鉴定。 第六章为文献综述，概述了羌活药材的研究进展。对羌活属及药用羌活植物从分类学、本草学、品质评价、人工栽培、化学成分及药理作用等方面进行了文献归纳和总结。 In this dissertation, an electrospray ionization mass spectrometry (ESI-MS) signal enhancement method, as well as the work of bioactive components study, HPLC-MS/MS application, bioassay screening, chromatograph separation and structure identification of the metabolites in several medicinal herbs have been reported. First chapter expounded a rapid, simple ESI-MS sensitivity enhancement method for detecting carbonyl groups in natural products has been developed by using hydroxylamine hydrochloride (NH2OH·HCl) as a derivatization reagent. We use the oxime formed during the derivatization reactions and its Beckmann rearrangement intermediates as a means of detecting the carbonyl groups originally present in these triterpenoids. In comparison with other derivatization methods in the literature, this method is simple, specific and can be used to detect carbonyl groups in triterpenoids which have low polarity and are poorly or non-ionizable. Moreover, it can also be used to detect hydroxyl groups by using the Dess-Martin periodinane (DMP) to convert primary and secondary hydroxyls into carbonyl groups. Chapter 2 reported an HPLC-MS method for analyzing the main bioactive compounds in both wild and cultured Notopterygium incisum. The results indicated that the main bioactive compounds varied through different seasons regularly, and in different commercial parts of this herb the content of these compounds also differed from each other. The quantitative analysis results showed that in the traditional commercial parts, the content of main chemical constitutes in Silkworm Notopterygium, Bamboo Notopterygium and Irregular-nodal Notopterygium are higher than that in Striped Notopterygium. This result is tally with the traditionally concept that the quality of Notopterygium, Bamboo Notopterygium and Irregular-nodal Notopterygium are better than that of Striped Notopterygium, which means that the quality of rhizomes is better than main roots. The chemical constituents of cultured N. incisum is reported for the first time in this dissertation and the analysis results showed some growth curves of chemical constituents in this plant, but still left some questions unanswered. Chapter 3 discussed the GC/LC-MS analysis of the traditional Chinese medicines Codonopsis thalictrifolis, Passiflora incarnate, Belamcanda chinensis and Passiflora incarnate. The main constituent, luteolin was isolated and identified from the traditional Tibet medicine of C. thalictrifolis. The quantitative analysis by HPLC has revealed that the content of luteolin in this herb is 0.7%. GC-MS was employed to analyzed chemical constituents of the essential oil from the flower of C. thalictrifolis. More than 60 peaks were detected and 45 of them were identified by comparing their spectra with that of the standards in the database and literatures. ESI-MS/MS was used to analyze the n-butanol extract of Passiflora incarnate. Based on the information of pseudo molecular ions and fragment ions of the glycosides, four major flavone-C-glycosides have been detected and identified as 7-methoxyluteolin-6-C-β-D-glucopyranoside, vitexin, swertisin and orientin. The isoflavone compounds in theextracts of three samples of B. chinensis collected in Gansu, Sichuan and Hunan, and the extract of Iris tectorum collected in Sichuan were analyzed by using TOF-HRMS and IT-MS. From the extracts of these herbs, a new isoflavone, identified as 5’,5,6,7-tetrahydroxy-3’4’-dimethoxyl isoflavon, and 7 known ones have been identified by analyzing the fragmentation patterns and their molecular formulas given by HRMS and the tandem mass spectrometry acquired by IT-MS. Chapter 4 elucidated the isolation and identification of a new triterpene saponin, androsacin (1), along with five known compounds (2-6) were isolated from the whole plants of Androsace integra (Maxim.) Hand.-Mazz., an herb used in traditional Chinese and Tibetan medicine. The chemical structure of the new compound was established as 3β-O-{β-D-glucopyranosyl-(1→4)-O-β-D-xylopyranosyl-(1→2)-O-β-D-glucopyranosyl-(1→4)-[O-β-D-glucopyranosyl-(1→2)]-α-L-arabinopyranosyl}-16α-hydroxy-13β,28-epoxy-olean-30-al by analyzing its MS, 1D- and 2D-NMR spectra. Compound 2 was cytotoxic toward HepG2 cancer cell with the GI50 value of 1.65 μg/mL. Chapter 5 described the biogenic pesticide activity screening of 68 traditional Chinese and Tibetan medicine extractions. The intention of this study is to explore bioactive natural compounds from these traditional medicinal herbs for biogenic insecticides use. Based on Syngenta’s bioassay, 14 extractions of these traditional medicines showed pesticide activities, and some of them had multi-activities on antibacterial and insecticidal. Chapter 6 is a review on the chemical and bioactivity research progress of Notopterygium incisum and N. forbesii.