Review of the Performance of Residential PV systems in France

The main objective of this paper is to review the state of the art of residential PV systems in France. This is done analyzing the operational data of 6868 installations. Three main questions are posed. How much energy do they produce? What level of performance is associated to their production? Which are the key parameters that most influence their quality? During the year 2010, the PV systems in France have produced a mean annual energy of 1163 kWh/kWp. As a whole, the orientation of PV generators causes energy productions to be some 7% inferior to optimally oriented PV systems. The mean Performance Ratio is 76% and the mean Performance Index is 85%. That is to say, the energy produced by a typical PV system in France is 15% inferior to the energy produced by a very high quality PV system. On average, the real power of the PV modules falls 4.9% below its corresponding nominal power announced on the manufacturer's datasheet. A brief analysis by PV modules technology has led to relevant observations about two technologies in particular. On the one hand, the PV systems equipped with heterojunction with intrinsic thin layer (HIT) modules show performances higher than average. On the other hand, the systems equipped with the copper indium (di)selenide (CIS) modules show a real power that is 16% lower than their nominal value.

An investigation of the performance of a new Mechanical thrombectomy device using Bond Graph modelling: application to the extraction of blood clots in the middle cerebral artery

A number of thrombectomy devices using a variety of methods have now been developed to facilitate clot removal. We present research involving one such experimental device recently developed in the UK, called a ‘GP’ Thrombus Aspiration Device (GPTAD). This device has the potential to bring about the extraction of a thrombus. Although the device is at a relatively early stage of development, the results look encouraging. In this work, we present an analysis and modeling of the GPTAD by means of the bond graph technique; it seems to be a highly effective method of simulating the device under a variety of conditions. Such modeling is useful in optimizing the GPTAD and predicting the result of clot extraction. The aim of this simulation model is to obtain the minimum pressure necessary to extract the clot and to verify that both the pressure and the time required to complete the clot extraction are realistic for use in clinical situations, and are consistent with any experimentally obtained data. We therefore consider aspects of rheology and mechanics in our modeling.

Flow and fracture behaviour of high performance alloys

Based on our needs, that is to say, through precise simulation of the impact phenomena that may occur inside a jet engine turbine with an explicit non-linear finite element code, four new material models are postulated. Each one of is calibrated for four high-performance alloys that can be encountered in a modern jet engine. A new uncoupled material model for high strain and ballistic is proposed. Based on a Johnson-Cook type model, the proposed formulation introduces the effect of the third deviatoric invariant by means of three different Lode angle dependent functions. The Lode dependent functions are added to both plasticity and failure models. The postulated model is calibrated for a 6061-T651 aluminium alloy with data taken from the literature. The fracture pattern predictability of the JCX material model is shown performing numerical simulations of various quasi-static and dynamic tests. As an extension of the above-mentioned model, a modification in the thermal softening behaviour due to phase transformation temperatures is developed (JCXt). Additionally, a Lode angle dependent flow stress is defined. Analysing the phase diagram and high temperature tests performed, phase transformation temperatures of the FV535 stainless steel are determined. The postulated material model constants for the FV535 stainless steel are calibrated. A coupled elastoplastic-damage material model for high strain and ballistic applications is presented (JCXd). A Lode angle dependent function is added to the equivalent plastic strain to failure definition of the Johnson-Cook failure criterion. The weakening in the elastic law and in the Johnson-Cook type constitutive relation implicitly introduces the Lode angle dependency in the elastoplastic behaviour. The material model is calibrated for precipitation hardened Inconel 718 nickel-base superalloy. The combination of a Lode angle dependent failure criterion with weakened constitutive equations is proven to predict fracture patterns of the mechanical tests performed and provide reliable results. A transversely isotropic material model for directionally solidified alloys is presented. The proposed yield function is based a single linear transformation of the stress tensor. The linear operator weighs the degree of anisotropy of the yield function. The elastic behaviour, as well as the hardening, are considered isotropic. To model the hardening, a Johnson-Cook type relation is adopted. A material vector is included in the model implementation. The failure is modelled with the Cockroft-Latham failure criterion. The material vector allows orienting the reference orientation in any other that the user may need. The model is calibrated for the MAR-M 247 directionally solidified nickel-base superalloy.

SIMLIDAR Simulation of LiDAR performance in artificially simulate orchards

SIMLIDAR is an application developed in Cþþ that generates an artificial orchard using a Lindenmayer system. The application simulates the lateral interaction between the artificial orchard and a laser scanner or LIDAR (Light Detection and Ranging). To best highlight the unique qualities of the LIDAR simulation, this work focuses on apple trees without leaves, i.e. the woody structure. The objective is to simulate a terrestrial laser sensor (LIDAR) when applied to different artificially created orchards and compare the simulated characteristics of trees with the parameters obtained with the LIDAR. The scanner is mounted on a virtual tractor and measures the distance between the origin of the laser beam and the nearby plant object. This measurement is taken with an angular scan in a plane which is perpendicular to the route of the virtual tractor. SIMLIDAR determines the distance measured in a bi-dimensional matrix N M, where N is the number of angular scans and M is the number of steps in the tractor route. In order to test the data and performance of SIMLIDAR, the simulation has been applied to 42 different artificial orchards. After previously defining and calculating two vegetative parameters (wood area and wood projected area) of the simulated trees, a good correlation (R2 ¼ 0.70e0.80) was found between these characteristics and the wood area detected (impacted) by the laser beam. The designed software can be valuable in horticulture for estimating biomass and optimising the pesticide treatments that are performed in winter.

Flexibility, innovation and sustainability in business models as determinants of firm performance heterogeneity.

La comprensión actual de la heterogeneidad de las empresas académico rendimiento en el entorno entra industria necesita un mayor desarrollo. Gestión estratégica y el discurso sobre la literatura empresarial necesita mayor explicación de por qué los modelos de negocio aparentemente similares en el mismo sector actúan de forma diferente. También qué factores del entorno sectorial y operativo determina el surgimiento y funcionamiento de los modelos de negocio sostenibles e innovadoras permanecen sin explorar. Un marco se conceptualiza acompañado de estudios de caso sobre la compañía aérea y las industrias de energía renovable. El estudio lleva a una visión basada en los recursos de los modelos de negocio que las empresas alcancen posiciones heterogéneas de recursos. Una explicación para la heterogeneidad firme desempeño que se busca por intermediación conocimiento que genera valor a partir de la utilización eficaz de los recursos de conocimientos adquiridos a entornos entra y inter-empresa. Un marco para la aparición de nuevos modelos de negocios verdes se conceptualiza y deducciones se obtienen mediante un estudio de caso sobre la base de la industria de biocombustibles de energías renovables para explicar la dinámica de los mercados verdes y cómo se puede crear valor sostenible y capturó e innovadora de los modelos de negocios verdes. El marco desarrollado proporciona una visión cíclica de la flexibilidad del modelo de negocio en la que se propaga la acumulación de recursos basada en el conocimiento del modelo de negocio a través de los ambientes dentro y inter-empresa. Estrategias de conocimiento de corretaje del resultado ambientes inter e dentro-firma en un mejor desempeño del modelo de negocio. La flexibilidad del modelo de negocio que adquiere está determinada por la eficiencia con la acumulación de recursos está alineado con su ambiente externo. Las características de la que el modelo de negocio alcanza ventajas competitivas, como la innovación y la flexibilidad se atribuyen a la heterogeneidad de los recursos. La investigación se extiende a la literatura orientación de servicio al conceptualizar y medir la orientación a servicios como un requisito clave para la innovación del modelo de negocio, mientras que aboga por la necesidad de identificar correctamente las competencias básicas de la empresa, especialmente relevante en el contexto de la empresa orientada a los servicios, donde la creación de valor requiere recursos y la prestación eficiente de los servicios. La investigación trata de llegar a una descripción de los modelos de negocio sostenibles verdes y argumenta que la innovación, la flexibilidad y la sostenibilidad son los tres habilitadores básicos de los cuales el concepto de modelo de negocio verde puede evolucionar la explotación de nuevos mecanismos de mercado y los mercados para crear y capturar valor en el mantenimiento de su innovadora ambiente externo. La investigación integra efectivamente los conceptos de corretaje de conocimientos y modelos de negocio a partir de un recurso basado en la acumulación de vista y al mismo tiempo llega a la heterogeneidad rendimiento de los modelos de negocio aparentemente similares dentro de la misma industria. La investigación indica cómo se producen perturbaciones del mercado en una industria como resultado de modelos de negocio innovador y flexible, y cómo los nuevos modelos de negocio evolucionan en base a estos trastornos. Avanza la comprensión de cómo la estrategia de núcleo competencia y la innovación del modelo de negocio construcciones se comportan en el esfuerzo de la empresa de servicios para obtener una ventaja competitiva sostenible. Los resultados tienen implicaciones en el rendimiento de las empresas que empiezan sin recursos distintos de los suyos, o que utilizan un modelo de negocio imitado, para lograr un mejor rendimiento a través de la evolución del modelo de negocio alineado con las exitosas estrategias de conocimiento de corretaje. Dicho marco puede permitir a las empresas a evaluar y elegir un modelo de negocio basado en la innovación, la flexibilidad, la sostenibilidad y las opciones para el cambio. La investigación se suma a la literatura acumulación de recursos, explicando cómo los recursos pueden ser efectivamente adquirida para crear valor. La investigación también se suma a la literatura empresarial verde, explicando cómo las empresas crear y capturar valor en los nuevos mecanismos dinámicos de mercado.

Dimensional synthesis of a spherical parallel manipulator based on the evaluation of global performance indexes

In this work, the dimensional synthesis of a spherical Parallel Manipulator (PM) with a -1S kinematic chain is presented. The goal of the synthesis is to find a set of parameters that defines the PM with the best performance in terms of workspace capabilities, dexterity and isotropy. The PM is parametrized in terms of a reference element, and a non-directed search of these parameters is carried out. First, the inverse kinematics and instantaneous kinematics of the mechanism are presented. The latter is found using the screw theory formulation. An algorithm that explores a bounded set of parameters and determines the corresponding value of global indexes is presented. The concepts of a novel global performance index and a compound index are introduced. Simulation results are shown and discussed. The best PMs found in terms of each performance index evaluated are locally analyzed in terms of its workspace and local dexterity. The relationship between the performance of the PM and its parameters is discussed, and a prototype with the best performance in terms of the compound index is presented and analyzed.

Simulation of academic performance rates, estimation of indicators of subjects and of a complete degree

The purpose of this paper is to present a program written in Matlab-Octave for the simulation of the time evolution of student curricula, i.e, how students pass their subjects along time until graduation. The program computes, from the simulations, the academic performance rates for the subjects of the study plan for each semester as well as the overall rates, which are a) the efficiency rate defined as the ratio of the number of students passing the exam to the number of students who registered for it and b) the success rate, defined as the ratio of the number of students passing the exam to the number of students who not only registered for it but also actually took it. Additionally, we compute the rates for the bachelor academic degree which are established for Spain by the National Quality Evaluation and Accreditation Agency (ANECA) and which are the graduation rate (measured as the percentage of students who finish as scheduled in the plan or taking an extra year) and the efficiency rate (measured as the percentage of credits which a student who graduated has really taken). The simulation is done in terms of the probabilities of passing all the subjects in their study plan. The application of the simulator to Polytech students in Madrid, where requirements for passing are specially stiff in first and second year subjects, is particularly relevant to analyze student cohorts and the probabilities of students finishing in the minimum of four years, or taking and extra year or two extra years, and so forth. It is a very useful tool when designing new study plans. The calculation of the probability distribution of the random variable "number of semesters a student has taken to complete the curricula and graduate" is difficult or even unfeasible to obtain analytically, and this is even truer when we incorporate uncertainty in parameter estimation. This is why we apply Monte Carlo simulation which not only provides illustration of the stochastic process but also a method for computation. The stochastic simulator is proving to be a useful tool for identification of the subjects most critical in the distribution of the number of semesters for curriculum vitae (CV) completion and subsequently for a decision making process in terms of CV planning and passing standards in the University. Simulations are performed through a graphical interface where also the results are presented in appropriate figures. The Project has been funded by the Call for Innovation in Education Projects of Universidad Politécnica de Madrid (UPM) through a Project of its school Escuela Técnica Superior de Ingenieros Industriales ETSII during the period September 2010-September 2011.

The seminar of nuclear safety in advanced reactors and the seminar of nuclear fusion: two formative initiatives from Universidad Politécnica de Madrid and spanish young Generation in Nuclear (Jóvenes Nucleares)

panish Young Generation in Nuclear (Jóvenes Nucleares) is a commission of the Spanish Nuclear Society (SNE), whose main goals are to spread knowledge about nuclear energy among the society. Following this motivation, two Seminars have been carried out with the collaboration of the Technical University of Madrid: The Seminar of Nuclear Safety in Advanced Reactors (SRA) and the Seminar of Nuclear Fusion (SFN). The first one, which has been celebrated every year since 2010, aims to show clearly the advances that have been obtained in the section of safety with the new reactors, from a technical but simple point of view and without needing great previous nuclear engineering knowledge. The second one, which first edition was held in 2011, aims to give a general overview of the past, present and future situation of nuclear fusion technology, and was born as a result of the increasing interest of our Spanish Young Generation members in this technology.

Complexity in the Optimisation of ATM Performance Metrics

Today's motivation for autonomous systems research stems out of the fact that networked environments have reached a level of complexity and heterogeneity that make their control and management by solely human administrators more and more difficult. The optimisation of performance metrics for the air traffic management system, like in other networked system, has become more complex with increasing number of flights, capacity constraints, environmental factors and safety regulations. It is anticipated that a new structure of planning layers and the introduction of higher levels of automation will reduce complexity and will optimise the performance metrics of the air traffic management system. This paper discusses the complexity of optimising air traffic management performance metrics and proposes a way forward based on higher levels of automation.

Analysis of the performance of caissons with a yard and cylindrical geometry as a breakwater. Apollonius caisson

En el presente trabajo se analiza el cajón Apolonio como diseño conceptual para controlar la reflexión en monolitos de gravedad sometidos a esfuerzos dinámicos de oleaje.

Assessment of troughput performance under NS2 in Mobile Ad Hoc Networks (MANETs)

Providing QoS in the context of Ad Hoc networks includes a very wide field of application from the perspective of every level of the architecture in the network.In order for simulation studies to be useful, it is very important that the simulation results match as closely as possible with the test bed results. In this Paper, we study the throughput performance (parameter QoS) in Mobile Ad Hoc Networks (MANETs) and compares emulated test bed results with simulation results from NS2 (Network Simulator). The performance of the Mobile Ad Hoc Networks is very sensitive to the number of users and the offered load. When the number of users/offered load is high then the collisions increase resulting in larger wastage of the medium and lowering overall throughput. The aim of this research is to compare the throughput of Mobile Ad Hoc Networks using three different scenarios: 97, 100 and 120 users (nodes) using simulator NS2. By analyzing the graphs in MANETs, it is concluded When the number of users o nodes is increased beyond the certain limit, throughput decreases.

Effectiveness for Ddtecting faults within and outside the scope of testing techniques: an independent replication

The verification and validation activity plays a fundamental role in improving software quality. Determining which the most effective techniques for carrying out this activity are has been an aspiration of experimental software engineering researchers for years. This paper reports a controlled experiment evaluating the effectiveness of two unit testing techniques (the functional testing technique known as equivalence partitioning (EP) and the control-flow structural testing technique known as branch testing (BT)). This experiment is a literal replication of Juristo et al. (2013).Both experiments serve the purpose of determining whether the effectiveness of BT and EP varies depending on whether or not the faults are visible for the technique (InScope or OutScope, respectively). We have used the materials, design and procedures of the original experiment, but in order to adapt the experiment to the context we have: (1) reduced the number of studied techniques from 3 to 2; (2) assigned subjects to experimental groups by means of stratified randomization to balance the influence of programming experience; (3) localized the experimental materials and (4) adapted the training duration. We ran the replication at the Escuela Politécnica del Ejército Sede Latacunga (ESPEL) as part of a software verification & validation course. The experimental subjects were 23 master?s degree students. EP is more effective than BT at detecting InScope faults. The session/program andgroup variables are found to have significant effects. BT is more effective than EP at detecting OutScope faults. The session/program and group variables have no effect in this case. The results of the replication and the original experiment are similar with respect to testing techniques. There are some inconsistencies with respect to the group factor. They can be explained by small sample effects. The results for the session/program factor are inconsistent for InScope faults.We believe that these differences are due to a combination of the fatigue effect and a technique x program interaction. Although we were able to reproduce the main effects, the changes to the design of the original experiment make it impossible to identify the causes of the discrepancies for sure. We believe that further replications closely resembling the original experiment should be conducted to improve our understanding of the phenomena under study.

Oxygen extended sooting index of FAME blends with aviation kerosene

The use of biofuels in the aviation sector has economic and environmental benefits. Among the options for the production of renewable jet fuels, hydroprocessed esters and fatty acids (HEFA) have received predominant attention in comparison with fatty acid methyl esters (FAME), which are not approved as additives for jet fuels. However, the presence of oxygen in methyl esters tends to reduce soot emissions and therefore particulate matter emissions. This sooting tendency is quantified in this work with an oxygen-extended sooting index, based on smoke point measurements. Results have shown considerable reduction in the sooting tendency for all biokerosenes (produced by transesterification and eventually distillation) with respect to fossil kerosenes. Among the tested biokerosenes, that made from palm kernel oil was the most effective one, and nondistilled methyl esters (from camelina and linseed oils) showed lower effectiveness than distilled biokerosenes to reduce the sooting tendency. These results may constitute an additional argument for the use of FAME’s as blend components of jet fuels. Other arguments were pointed out in previous publications, but some controversy has aroused over the use of these components. Some of the criticism was based on the fact that the methods used in our previous work are not approved for jet fuels in the standard methods and concluded that the use of FAME in any amount is, thus, inappropriate. However, some of the standard methods are not updated for considering oxygenated components (like the method for obtaining the lower heating value), and others are not precise enough (like the methods for measuring the freezing point), whereas some alternative methods may provide better reproducibility for oxygenated fuels.

Boundariesc@pes. Landscapes of the boundary or boundaries of the landscape? The landscape scope of the boundary

Esta comunicación parte de la base de que en nuestro tiempo la idea ambigua del límite ha llegado a ser uno de los paradigmas más complejos que podemos afrontar no sólo en arquitectura sino también en la sociedad y la cultura.

Inluence of source and level of glycerin in the diet on growth performance, liver characteristics, and nturient digestibility in broilers from hatching to 21 days of age

The influence of source and level of inclusion of raw glycerin (GLYC) in the diet on growth performance, digestive traits, total tract apparent retention (TTAR), and apparent ileal digestibility of nutrients was studied in broilers from 1 to 21 d of age. There was a control diet based on corn and soybean meal and 8 additional diets that formed a 2 × 4 factorial with 2 sources of GLYC and 4 levels of inclusion (2.5, 5.0, 7.5, and 10%). The GLYC used were obtained from the same original batch of soy oil that was dried under different processing conditions and contained 87.5 or 81.6% glycerol, respectively. Type of processing of the GLYC did not affect any of the variables studied except DM and organic matter retention (P < 0.05) that was higher for the 87.5% glycerol diet. From d 1 to 21, feed conversion ratio (FCR) improved linearly (L, P ≤ 0.01) as the GLYC content of the diet increased, but ADG was not affected. On d 21, the relative weight (% BW) of the liver and the digestive tract increased (L, P < 0.01) as the level of GLYC in the diet increased, but lipid concentration in the liver was not affected. The TTAR of DM and organic matter increased quadratically (Q, P < 0.05) and the AMEn content of the diet increased linearly (L, P < 0.01) with increases in dietary GLYC. Also, the apparent ileal digestibility of DM (L, P < 0.05; Q, P = 0.07) and gross energy (L, P < 0.01) increased as the GLYC content of the diet increased. It is concluded that raw GLYC from the biodiesel industry can be used efficiently, up to 10% of the diet, as a source of energy for broilers from 1 to 21 d of age and that the energy content of well-processed raw GLYC depends primarily on its glycerol content.