Evaluación del comportamiento mecánico, estructural y frente a la corrosión, de una nueva armadura de acero inoxidable dúplex bajo en níquel

La durabilidad de las estructuras de hormigón armado no es ilimitada, en especial en determinados ambientes. El ingreso de agentes agresivos en el hormigón, fundamentalmente dióxido de carbono e iones cloruros, rebasando el espesor del recubrimiento y alcanzando las armaduras, reducen el alto pH del hormigón hasta alcanzar un umbral crítico, por debajo del cual, el acero queda despasivado. Posteriormente, si existe el suficiente aporte de humedad y oxígeno, el acero se corroe, lo que supone drásticas reducciones de la vida de servicio de estas estructuras y su inevitable reparación. La utilización de armaduras de acero inoxidable es una alternativa que está recibiendo cada vez más consideración. Su resistencia a la corrosión en los ambientes más agresivos, incluso con ataque de cloruros, lo convierte en el material idóneo para prolongar de forma muy considerable la vida útil de la estructura. En este trabajo se ha evaluado el comportamiento mecánico y estructural, y de resistencia a la corrosión, de un nuevo acero inoxidable dúplex de bajo contenido en níquel, el EN 1.4482 (AISI 2001), y se ha comparado con el inoxidable austenítico más utilizado, el EN 1.4301 (AISI 304), con el dúplex EN 1.4362 (AISI 2304) y con el tradicional acero al carbono B-500-SD. El estudio mecánico y estructural se ha realizado en tres niveles diferentes: a nivel de barra, estudiando las propiedades mecánicas y de ductilidad de los cuatro aceros citados; a nivel de sección, estudiando su comportamiento a flexión con diferentes cuantías de armado por medio de los diagramas momento-curvatura; y a nivel de pieza, ensayando una serie de vigas armadas con diferentes aceros y cuantías, y comprobando su comportamiento a desplazamiento y resistencia por medio de los diagramas carga-desplazamiento. El estudio de resistencia a la corrosión se ha realizado embebiendo barras corrugadas, de los tres aceros inoxidables mencionados, en probetas de mortero contaminadas con diferentes cantidades de cloruros, y realizando mediciones electroquímicas durante un periodo de al menos un año. Se han preparado probetas de mortero para dos comparativas diferentes. La primera, manteniendo las probetas en un desecador con el 95 % de humedad relativa durante todo el periodo de mediciones. La segunda, sumergiendo parcialmente las probetas en una solución tampón para carbonatar el mortero. Los resultados de los ensayos mecánicos han demostrado dos aspectos diferentes. Uno, que las armaduras de acero inoxidable tienen un comportamiento muy similar a las de acero al carbono en lo referente a las resistencias alcanzadas, en el límite elástico y en rotura, pero distinto en cuanto al módulo de deformación longitudinal, cuyo valor es claramente inferior al del acero al carbono, por lo que su utilización en las estructuras de hormigón necesita tener en cuenta ese dato en los análisis lineales de cálculo. El segundo aspecto es que las armaduras de acero inoxidable laminadas en caliente presentan una ductilidad muy superior a las de acero al carbono, por lo que ofrecen una mayor seguridad frente a su rotura o al colapso de la estructura, lo que se debe tener en cuenta en el análisis de cálculo plástico. En cambio, las armaduras de acero inoxidable laminadas en frío sólo cumplen con los límites mínimos de ductilidad establecidos en la instrucción EHE-08 para los aceros soldables, y no para los aceros con características especiales de ductilidad. El estudio a nivel de sección refleja la paradoja de obtener secciones menos dúctiles con las armaduras de acero inoxidable laminadas en caliente que con las armaduras de acero al carbono. Para subsanarlo, se definen los conceptos de curvatura última de rotura y ductilidad de la sección en rotura, que tienen en cuenta las altas deformaciones alcanzadas por las armaduras de acero inoxidable. Los resultados a nivel de pieza permiten identificar el comportamiento estructural del hormigón armado con barras corrugadas de acero inoxidable y compararlo con el de las estructuras de hormigón armado convencionales, verificando los resultados experimentales con los teóricos obtenidos con la formulación recogida en la instrucción EHE- 08. Los ensayos de resistencia a la corrosión por cloruros demuestran, durante el primer año y medio de vida de las probetas, un comportamiento muy similar entre el nuevo acero inoxidable dúplex bajo en níquel y el austenítico y el dúplex utilizados para la comparación, incluso para las probetas carbonatadas. Por último, se añade una comparativa económica, realizada sobre dos edificaciones tipo, para cuantificar el sobrecoste que supone la utilización de armaduras de acero inoxidable respecto a las de acero al carbono. El alto coste inicial de las armaduras de acero inoxidable se ve compensado en el coste final de la estructura de muy diferentes formas, principalmente dependiendo del grado de acero elegido y de si se emplean en el total de la estructura o solamente en los elementos más expuestos. The durability of the concrete structures is limited, especially in certain environments. The attack of aggressive agents in the concrete, mainly carbon dioxide and chloride ions, penetrating the thickness of concrete cover and reaching the reinforcements, reduce the high pH of concrete to the point of reaching a critical threshold, under which, the steel despasivates. Therefore, if there is enough humidity and oxygen, the steel corroes, causing drastic reductions in the service life of these structures and its inevitable repair. Despite the high initial cost compared to carbon steel, the usage of stainless steel reinforcements is an alternative with a major consideration nowadays. Its resistance to corrosion in the most aggressive atmospheres, including chlorides attack, makes the stainless steel a suitable material to extend considerably its lifetime. In this study, it’s been evaluated the mechanical and structural behaviour, and the corrosion resistance, of a new low-nickel duplex stainless steel EN 1.4482 (AISI 2001), and it has been compared with the most widely used austenitic type EN 1.4301 (AISI 304), with duplex steel EN 1.4362 (AISI 2304) and with the traditional carbon steel B-500-SD. The mechanical and structural study has been carried out in three different levels: bar level, studying mechanical properties and ductility of the four steels; section level, studying its behaviour when blending with different amounts of reinforcement through the moment-curvature diagrams; and structural element level, testing a series of reinforced beams with different steels and amounts, and checking its sag and resistance through the load-deflection diagrams. The corrosion resistance study was performed by embedding ribbed bars, using the three stainless steel listed, on mortar specimens contaminated with different amounts of chlorides, and taking electrochemical measurements over a period of at least one year. Mortar specimens have been prepared for two different comparisons. The first, keeping the specimens at 95% of relative humidity during the measurement period. The second, immersing the specimens partially in a carbonate buffer solution. The results of those tests have proved two different aspects. Firstly, that stainless steel reinforcements show a very similar behaviour to carbon steel, according to the reached levels of mechanical resistance, yield stress and steel strength, but a different behaviour in Young’s modulus, which value is clearly lower than the carbon steel. Therefore, when using in concrete structures it is need to consider on that point the existing calculus of linear analysis. The second aspect is that stainless steel reinforcement manufactured by hot-rolling process show a very higher ductility than carbon steel, offering a better security on cracks or structure collapse, which it has to be taken into account on plastic calculus analysis. However, the stainless steel reinfor9 cement cold-rolled bars only meet the minimum thresholds of ductility established by EHE-08 for welded steel, and not for steels with special ductility. The results at the section level reflect the paradox of getting less ductile sections with hot rolled stainless steel reinforcement than with carbon steel reinforcements. To overcome that, the concepts of last break curvature and break ductility section have been defined, which take into account the high deformation value achieved by stainless steel reinforcements. The results at the structural element level allow to identify the structural behaviour of reinforced concrete with stainless steel reinforcements and compared with that of conventional steel reinforcement, contrasting the experimental with the theoretical results obtained from the formulation contained in the instruction EHE-08. Tests on resistance of chloride corrosion show during the first year and a half of specimens life, a similar behaviour between the new low nickel duplex stainless steel and austenitic and duplex used for comparison, even for carbonated specimens. Finally, it has been included an economic comparison on two differents building types, to quantify the additional cost involved on the use of stainless steel reinforcement compared to that of carbon steel. The high initial cost of stainless steel reinforcements is offset in the final cost of the structure in many different ways, mainly depending on the chosen steel grade and whether the reinforcement is used in the total structure or only in risky structural elements.

Beitrag zur Entwicklung der Querschnittsgestaltung im Verbundbrückenbau

Die grafische Darstellung des Verbundquerschnittes mit einer oberen Betonplatte und einem darunter liegenden Stahlträger war seit seiner Vorstellung in den 1950er Jahren ein Symbol, das weit über die Theorie hinausging und weite Verbreitung in der Praxis des Verbundbrückenbaus fand. Seit den 1970er bzw. 1980er Jahren hat dieses Bild – bedingt durch neue und freiere Formen, Beton und Stahl miteinander zu kombinieren – seine Symbolhaftigkeit verloren. In Deutschland und Spanien wurde der Doppelverbund mit unten liegenden Betonplatten in Bereichen mit negativen Momenten eingeführt, in Frankreich werden Stahlträger auch in vorgespannten Betonquerschnitten eingebettet. Beide Ansätze haben dazu beigetragen, dass in der Gegenwart die Materialien Stahl und Beton im Verbundbau frei miteinander kombiniert werden können. On the development of sections in composite bridges. A comprehensive theory of composite construction was established in Germany by Sattler in 1953. The theoretical image of the composite section with a superior concrete slab and a lower metallic structure was shaped in addition to the analytical resolution. Theory and graphical representation were going to be known together in Europe. This figure was repeated in all theoretical and academic publications, so becoming an authentic icon of the composite section. Its translation to the bridge deck in flexion was obvious: the superior slab defines the tread platform, while the metallic structure was left off-hook at the bottom. Nevertheless, in continuous decks the section is not optimal at all in zones of negative bending moments. But the overcoming of the graphical representation of the theory did not happen immediately. It was produced after a process in which several European countries played an active role and where different mechanisms of technological transference were developed. One approach to this overcoming is the “double composite action”, with a lower concrete slab in areas of a negative bending moment. The first accomplishments, a bridge in Orasje built in 1968 with 134 m span, as well as the publications of the system proposed by Fabrizio de Miranda in 1971 did not extend nor had continuity. Spanish bridges by Fernández Ordoñez and Martínez Calzón used double composite action for the first time in 1979. The German team of Leonhard, Andrä und partners, has used it since the end of the 1980's to solve bridges of great span. Once the technology has been well known thanks to the ASCE International Congress and the Spanish International Meetings organised by the “Colegio de Ingenieros de Caminos”, double composite action has been integrated well into the structural vocabulary everywhere. In France the approach was different. What Michel Virlogeux calls “double floor composite section” was reached as an evolution of prestressed concrete bridges. In an experimental process widely known, the external prestressing allows weight reduction by diminishing the thickness of the concrete webs. The following step, in the 1980's, was the substitution of the webs by metallic elements: stiffened plates, trusses or folded plates. A direct result of this development is the Brass de la Plaine Bridge in the Reunion Island in 2001 with 280 m span. Both approaches have contributed to a freedom of design in composite construction in steel and concrete today.

Experimental study on the effective width of flat slab structures under dynamic seismic loading

This paper investigates the effective width of reinforced concrete flat slab structures subjected to seismic loading on the basis of dynamic shaking table tests. The study is focussed on the behavior of corner slab? column connections with structural steel I- or channel-shaped sections (shearheads) as shear punching reinforcement. To this end, a 1/2 scale test model consisting of a flat slab supported on four box-type steel columns was subjected to several seismic simulations of increasing intensity. It is found from the test results that the effective width tends to increase with the intensity of the seismic simulation, and this increase is limited by the degradation of adherence between reinforcing steel and concrete induced by the strain reversals caused by the earthquake. Also, significant differences are found between the effective width obtained from the tests and the values predicted by formula proposed in the literature. These differences are attributed to the stiffening effect provided by the steel profiles that constitute the punching shear reinforcement.

An analytical model for simulating the bond of prestressed concrete during the prestressed force release

A bond analytical model is proposed in this paper. The model is capable of reproducing the bond stress developed between the steel and concrete, in precast prestressed elements, during the entire process of prestressing force release. The bond stress developed in the transmission zone, where the bond stress is not constant, is also obtained. The steel and concrete stresses as well as the slip between both materials can be also estimated by means of the relation established in the model between these parameters and the bond stress. The model is validated with the results of a series of tests, considering different steel indentation depths and concrete covers and it is extended to evaluate the transmission length. This has been checked by comparing the transmission length predicted by the model and one measured experimentally in two series of tests.

Critical comparative evaluation of design methodologies for the ultimate limit state of fatigue in concrete structures

La aparición de la fatiga ha sido ampliamente investigada en el acero y en otros materiales metálicos, sin embargo no se conoce en tanta profundidad en el hormigón estructural. Esto crea falta de uniformidad y enfoque en el proceso de verificación de estructuras de hormigón para el estado límite último de la fatiga. A medida que se llevan a cabo más investigaciones, la información sobre los parámetros que afectan a la fatiga en el hormigón comienzan a ser difundidos e incluso los que les afectan de forma indirecta. Esto conlleva a que se estén incorporando en las guías de diseño de todo el mundo, a pesar de que la comprobación del estado límite último no se trata por igual entre los distintos órganos de diseño. Este trabajo presentará un conocimiento básico del fenómeno de la fatiga, qué lo causa y qué condiciones de carga o propiedades materiales amplían o reducen la probabilidad de fallo por fatiga. Cuatro distintos códigos de diseño serán expuestos y su proceso de verificación ha sido examinado, comparados y valorados cualitativa y cuantitativamente. Una torre eólica, como ejemplo, fue analizada usando los procedimientos de verificación como se indica en sus respectivos códigos de referencia. The occurrence of fatigue has been extensively researched in steel and other metallic materials it is however, not as broadly understood in concrete. This produces a lack of uniformity in the approach and process in the verification of concrete structures for the ultimate limit state of fatigue. As more research is conducted and more information is known about the parameters which cause, propagate, and indirectly affect fatigue in concrete, they are incorporated in design guides around the world. Nevertheless, this ultimate limit state verification is not addressed equally by various design governing bodies. This report presents a baseline understanding of what the phenomenon of fatigue is, what causes it, and what loading or material conditions amplify or reduce the likelihood of fatigue failure. Four different design codes are exposed and their verification process has been examined, compared and evaluated both qualitatively and quantitatively. Using a wind turbine tower structure as case study, this report presents calculated results following the verification processes as instructed in the respective reference codes.

Diseño de una Metodología de Política Pública de I+D+i para el Desarrollo de la Capacidad de la Innovación en el Sector PYMIS del estado Bolívar, Venezuela

El estado Bolívar con una superficie de 238.000 Km2 se encuentra ubicado al SE de Venezuela y su capital es Ciudad Bolívar. Ocupa el 26,24% de la superficie del territorio nacional. Ciudad Guayana es la principal región del desarrollo económico del estado siendo sede de las empresas básicas de los sectores siderúrgicos y del aluminio que se encargan de la extracción, procesamiento y transformación del mineral de hierro y de la transformación de la bauxita en aluminio primario. Además, cuenta con un gran potencial hidroeléctrico, garantizando el suministro de energía eléctrica para el funcionamiento de las empresas básicas, para el parque industrial de la región, así como para el desarrollo industrial, económico y social de la nación. Con relación al sector de la industria del mineral de hierro y del aluminio, las empresas destinan más del 60 por ciento de su producción al mercado internacional. A pesar de que el sector de las Pequeñas y Medianas Industrias (PYMIS) del estado Bolívar cuenta con un mercado cercano y seguro, no se le ha propiciado un desarrollo integral en términos de orientar sus esfuerzos en innovar en nuevos productos o mejoras de procesos. Debido a la falta del personal de investigación calificado, la escasa vinculación con centros de investigación, la baja inversión en investigación, desarrollo tecnológico e innovación (I+D+i), la ausencia de la aplicación de una política pública de I+D+i y la desarticulación de los miembros del Sistema Regional de Innovación (SRI), constituyen los principales obstáculos para generar bienes y servicios con un alto valor agregado. Esta situación desequilibra y hace ineficiente el funcionamiento del SRI. La baja capacidad de las PYMIS del estado Bolívar en I+D+i, es una situación que impide generar por si sola nuevos productos o procesos para satisfacer las demandas del mercado regional. Por lo tanto, se requiere de la intervención y participación activa de la institución gubernamental responsable del diseño y aplicación de una política pública de I+D+i para dinamizar la capacidad de innovación en las PYMIS, en su articulación y vinculación con los miembros del SRI. xiii El presente proyecto se planteó como objetivo diseñar una metodología de política pública de I+D+i para liderar, coordinar y direccionar el SRI del estado Bolívar, para el desarrollo de la capacidad de innovación en el sector industrial y específicamente en las PYMIS. La presente tesis representa una investigación no experimental de tipo proyectivo que analiza la situación actual del Sistema Regional de Innovación del estado Bolívar. El análisis de los resultados se ha dividido en tres fases. En la primera se realizan diagnósticos por medio de encuestas de las PYMIS en materia de I+D+i, de los centros y laboratorios de investigación pertenecientes a las universidades de la región en el área de Materiales y de los sectores financieros público y privado. En dichas encuestas se evalúa el nivel de integración con los entes gubernamentales que definen y administran la política pública de I+D+i. En la segunda fase, con el diagnóstico y procesamiento de los resultados de la primera fase, se procede a desarrollar un análisis de las fortalezas, oportunidades, debilidades y amenazas (FODA) del Sistema Regional de Innovación, permitiendo comprender la situación actual de la relación y vinculación de las PYMIS con los centros de investigación, instituciones financieras y entes gubernamentales. Con la problemática detectada, resultó necesario el diseño de estrategias y un modelo de gestión de política pública de I+D+i para la articulación de los miembros del SRI, para el apoyo de las PYMIS. En la tercera fase se diseña la metodología de política pública de I+D+i para fortalecer la innovación en las PYMIS. La metodología se representa a través de un modelo propuesto que se relaciona con las teorías de los procesos de innovación, con los modelos de sistemas de innovación y con las reflexiones y recomendaciones hechas por diferentes investigadores e instituciones de cooperación internacional referentes a la aplicación de políticas públicas de I+D+i para dinamizar la capacidad de innovación en el sector industrial. La metodología diseñada es comparada con diferentes modelos de aplicación de política pública de I+D+i. Cada modelo se representa en una figura y se analiza su xiv situación presente y la función que desempeña el ente gubernamental en la aplicación del enfoque de política pública de I+D+i. El diseño de la metodología de política pública de I+D+i propuesta aportará nuevos conocimientos y podrá ser aplicado para apoyar el progreso de la I+D+i en las PYMIS de la región, como caso de estudio, con el fin de impulsar una economía más competitiva y reducir el grado de dependencia tecnológica. La metodología una vez evaluada podrá ser empleada en el contexto de la gran industria y en otras regiones de Venezuela y además, puede aplicarse en otros países con características similares en su tejido industrial. En la tesis doctoral se concluye que el desarrollo de la capacidad de innovación en las PYMIS depende del diseño y aplicación de la política pública de I+D+i como elemento dinamizador y articulador del SRI del estado Bolívar. xv ABSTRACT The Bolivar state with an area of 238,000 km2 is located in the SE of Venezuela and its capital is Ciudad Bolivar. It occupies a surface which is 26.24% of the national territory. Ciudad Guayana is the main area of the state's economic development and the location of the corporate headquarters of the basic steel and aluminum sectors that are responsible for the extraction, processing and transformation of iron ore and bauxite processing for primary aluminum. It also has a great hydroelectric potential, ensuring the supply of electricity for the operation of enterprises, for the regional industrial park as well as for the industrial, economic and social development of the nation. With regard to the iron ore and aluminum industry, companies allocate more than 60 percent of their production to the international market. Although the sector of Small and Medium Industries (SMIs) of the Bolivar state has a secure market, it has not been led to an integral development in terms of targeting its efforts on innovating new products or improving processes. Due to the lack of qualified research staff, poor links with research centers, low investment in research, technological development and innovation (R & D & I), the absence of the implementation of a public policy for R & D & I and the dismantling of the members of the Regional Innovation System (RIS), are the main obstacles to generate goods and services with high added value. This situation makes the RIS unbalanced and inefficient. The low capacity of Bolivar state’s SMIs in R & D & I, is a situation that cannot generate by itself new products or processes to meet regional market demands. Therefore, it requires the active involvement and participation of the government institution responsible for the design and implementation of R & D & I public policy to boost the innovation capacity in SMIs, through the connection and integration with members of the RIS. This project is intended to design a methodology aimed at public policy for R & D & I to lead, coordinate and direct the RIS of Bolivar state, for the development of innovation capacity in the industrial sector and specifically in the SMIs. xvi This thesis is an experimental investigation of projective type which analyzes the current situation of the Regional Innovation System of the Bolivar state. The analysis of the results is divided into three phases. In the first one, a diagnosis is performed through surveys of SMIs in R & D & I centers and research laboratories belonging to the universities of the region in the area of materials and public and private financial sectors. In such surveys the level of integration with government agencies that define and manage the public policy of R & D & I is assessed. In the second phase, with the diagnosis and processing of the results of the first phase, we proceed to develop an analysis of the strengths, weaknesses, opportunities and threats (SWOT) of the Regional Innovation System, allowing the comprehension of the current status of the relationship of SMIs with research centers, financial institutions and government agencies. With the problems identified it was necessary to design strategies and a model of public policy management of R & D & I for the articulation of the members of the RIS, to support the SMIs. In the third phase a public policy methodology for R & D & I is designed in order to strengthen innovation in SMIs. The methodology is shown through a proposed model that relates to the theories of the innovation process, with models of innovation systems and with the discussions and recommendations made by different researchers and institutions of international cooperation concerning the implementation of policies public for R & D & I to boost innovation capacity in the industrial sector. The methodology designed is compared with different models of public policy implementation for R & D & I. Each model is represented in a figure and its current situation and the role of the government agency in the implementation of the public policy approach to R & D & I is analyzed. The design of the proposed public policy methodology for R & D & I will provide new knowledge and can be applied to support the progress of R & D & I in the region’s SMIs, as a case study, in order to boost a more competitive economy and reduce the degree of technological dependence. After being evaluated the methodology can be used in the context of big industry and in other regions of Venezuela and can also be applied in other countries with similar characteristics in their industrial structure. xvii The thesis concludes that the development of the innovation capacity in SMIs depends on the design and implementation of the public policy for R & D & I as a catalyst and coordination mechanism of the Regional Innovation System of the Bolivar state.

Diseño, fabricación, caracterización y aplicaciones constructivas de hormigones de consistencia seca con adiciones de materiales de procedencia orgánica e inorgánica de neumáticos fuera de uso (NFUs)

La siguiente investigación está centrada en establecer las diferencias en la reutilización, en los hormigones de consistencia seca, de dos tipos de caucho obtenidos en el proceso del reciclado del neumático, caucho reciclado del neumático (CRN): los tamaños del granulado (4-8 mm) de caucho reciclado de alta calidad (CR: Caucho Limpio) y el desecho del proceso del reciclado: fibra textil y de acero con trazas de caucho (desecho del caucho reciclado, IR: Caucho de impurezas). Ambos tipos fueron clasificados y añadidos como árido en sustitución del árido grueso (grava) desde el 20 al 100% del volumen. El comportamiento físico y mecánico del IR en los hormigones fue comparado con el hormigón de referencia y las series con el CR para el futuro uso en piezas de hormigón prefabricado. En ambos casos se aprecia una reducción de las resistencias mecánicas en proporción con las cantidades de caucho de sustitución, pero menos en series con IR con una combinación satisfactoria de fibra textil y metálica. El IR muestra mayores pérdidas en propiedades tales como trabajabilidad y densidad, pero también con un incremento de la porosidad. Estos hechos facilitan nuevas opciones para los desechos procedentes del CRN en los hormigones y por lo tanto menores gastos de energía, logrando una tasa de éxito en el proceso de reciclado cercano al 100%. The following research is focused on establishing the differences in the re-use as aggregate in dry consistency concretes of two types of rubber obtained in the process of tyre recycling, recycled rubber from tyres (RRT): granulated sizes (4–8 mm) of high quality recycled rubber (CR: Clean Rubber) and the waste of the recycling process: steel and textile fibers with rubber tracks (waste from recycled rubber, WRR). Both types were classified and added as aggregate in substitution of coarse aggregates from 20 to 100 % by volume. The physical and mechanical behavior of IR in concretes was compared with reference concrete and series with CR for a future use in precast concrete pieces. In both samples a reduction of mechanical resistance occurs in proportion with the amounts of rubber of substitution, but less in serials with IR with a successful combination of steel and textile fiber. IR shows furthermore a reduction in properties such as workability and density, but also an increment in porosity. These facts facilitate new options for waste from CRN in concretes and therefore lower energy costs, achieving a success rate in the recycling process close to 100 %.

Design equations for reinforced concrete members strengthened in shear with external FRP reinforcement formulated in an evolutionary multi-objective framework

Methods for predicting the shear capacity of FRP shear strengthened RC beams assume the traditional approach of superimposing the contribution of the FRP reinforcing to the contributions from the reinforcing steel and the concrete. These methods become the basis for most guides for the design of externally bonded FRP systems for strengthening concrete structures. The variations among them come from the way they account for the effect of basic shear design parameters on shear capacity. This paper presents a simple method for defining improved equations to calculate the shear capacity of reinforced concrete beams externally shear strengthened with FRP. For the first time, the equations are obtained in a multiobjective optimization framework solved by using genetic algorithms, resulting from considering simultaneously the experimental results of beams with and without FRP external reinforcement. The performance of the new proposed equations is compared to the predictions with some of the current shear design guidelines for strengthening concrete structures using FRPs. The proposed procedure is also reformulated as a constrained optimization problem to provide more conservative shear predictions.

An analytical model for simulating the bond of prestressed concrete during the prestressed force release

A bond analytical model is proposed in this paper. The model is capable of reproducing the bond stress developed between the steel and concrete, in precast prestressed elements, during the entire process of prestressing force release. The bond stress developed in the transmission zone, where the bond stress is not constant, is also obtained. The steel and concrete stresses as well as the slip between both materials can be also estimated by means of the relation established in the model between these parameters and the bond stress. The model is validated with the results of a series of tests, considering different steel indentation depths and concrete covers and it is extended to evaluate the transmission length. This has been checked by comparing the transmission length predicted by the model and one measured experimentally in two series of tests.

Characterisation of laser hybrid welded dissimilar joints

The investigation addresses the over-all performance of dissimilar joints of low carbon steel and stainless steel thin sheets achieved by laser hybrid welding. First, the technological de-velopment of dissimilar laser hybrid welding of thin sheets is briefly pre-sented. Joint characterisation by means of macro and microstructural examination and hardness tests is fur-ther described. Microhardness testing was used as an alternative and effi-cient mean of assessing the changes in mechanical properties of difficult to characterize areas, like HAZ and fu-sion zone of these thin sheets Laser-GMA dissimilar welded joints. The overall tensile performance of the joint is discussed together with the weld metal strength overmatching. The ten-sile tests results indicate that in case of transversally loaded joints, the po-sitive difference in yield strength between the weld metal and the base materials (overmatching welds) may reduce the weight of the structure, without diminishing its strength.

Influencia de los requisitos de seguridad a la fatiga en el dimensionamiento de puentes mixtos de carretera

El fenómeno de fatiga es uno de los condicionantes más importantes en el diseño de puentes metálicos y mixtos bajo la acción cíclica de fuertes sobrecargas reales. Hoy en día, ha tomado mayor relevancia en el ámbito de puentes de carretera debido al aumento sustancial de la intensidad de tráfico y el peso de los vehículos. La evolución de las normativas actuales, que recogen su cálculo a partir del ELU de seguridad a fatiga, debe ir dirigida, hacia una mayor simplicidad de aplicación y un mayor rigor técnico. A partir del análisis de seis puentes mixtos de carretera proyectados recientemente (2007-2011) se pretende establecer una comparación, tanto cualitativa como cuantitativa, entre los métodos simplificados de la normativa española (antigua RPM/RPX 95 y actual EAE) y el Eurocódigo frente al Método del Daño Acumulado, caracterizado por ser más complicado de aplicar pero más riguroso. A través del análisis efectuado, se obtienen reglas prácticas sencillas y fiables para el dimensionamiento o verificación de elementos estructurales a fatiga según características principales como la tipología de la sección o la longitud de vano, entre otros. En conclusión, el trabajo que se propone desarrollar combina el análisis crítico de la base teórica con el estudio aplicado de casos reales y pretende sentar las bases para profundizar en esta área de gran interés para proyectistas. Fatigue is one of the most determining factors in the design of steel and composite bridges with dynamic loads subject to cyclic live loads. Nowadays, it has taken relevance in the field of roadway bridges due to considerable increase in the intensity of traffic and the weight of vehicles. The evolution of the current design codes, which include an analysis of the ultimate limit state of fatigue, should aim for greater ease of application and technical rigour. Based on the analysis of six composite road bridges designed recently (2007-2011), a comparison has been made, both qualitative and quantitative, between the simplified methods of the Spanish codes (current EAE and old RPM/RPX95) and Eurocode with regard to the Cumulative Damage Method, characterised for being more difficult to apply but more rigorous. Through an exhaustive analysis, a set of practical and reliable rules have been obtained for the sizing or verification of structural elements according to main characteristics such as the tipology of the cross section or the length of span, among others. In conclusion, the work developed combines the critical analysis of the theory with the applied study of real cases and sets out to lay the foundations for deepening into this area of great interest to designers.

Muro cortina modular con marco de baja transmitancia térmica integrado en el vidrio aislante a través de adhesivos estructurales = Unitised curtain wall with low thermal transmittance frame integrated within the insulating glass unit through structural adhesives

Los muros cortina modulares están constituidos por paneles prefabricados que se fijan al edificio a través de anclajes a lo largo del borde del forjado. El proceso de prefabricación garantiza buena calidad y control de los acabados y el proceso de instalación es rápido y no requiere andamiaje. Por estas razones su uso está muy extendido en torres. Sin embargo, el diseño de los marcos de aluminio podría ser más eficiente si se aprovechara la rigidez de los vidrios para reducir la profundidad estructural de los montantes. Asimismo, se podrían reducir los puentes térmicos en las juntas si se sustituyeran los marcos por materiales de menor conductividad térmica que el aluminio. Esta investigación persigue desarrollar un muro cortina alternativo que reduzca la profundidad estructural, reduzca la transmisión térmica en las juntas y permita un acabado enrasado al interior, sin que sobresalgan los montantes. La idea consiste en conectar un marco de material compuesto de fibra de vidrio a lo largo del borde del vidrio aislante a través de adhesivos estructurales para así movilizar una acción estructural compuesta entre los dos vidrios y lograr una baja transmitancia térmica. El marco ha de estar integrado en la profundidad del vidrio aislante. En una primera fase se han efectuado cálculos estructurales y térmicos preliminares para evaluar las prestaciones a un nivel esquemático. Además, se han realizado ensayos a flexión en materiales compuestos de fibra de vidrio y ensayos a cortante en las conexiones adhesivas entre vidrio y material compuesto. Con la información obtenida se ha seleccionado el material del marco y del adhesivo y se han efectuado cambios sobre el diseño original. Los análisis numéricos finales demuestran una reducción de la profundidad estructural de un 80% y una reducción de la transmisión térmica de un 6% en comparación con un sistema convencional tomado como referencia. El sistema propuesto permite obtener acabados enrasados. ABSTRACT Unitised curtain wall systems consist of pre manufactured cladding panels which can be fitted to the building via pre fixed brackets along the edge of the floor slab. They are universally used for high rise buildings because the factory controlled assembly of units ensures high quality and allows fast installation without external access. However, its frame is structurally over-dimensioned because it is designed to carry the full structural load, failing to take advantage of potential composite contribution of glass. Subsequently, it is unnecessarily deep, occupying valuable space, and protrudes to the inside, causing visual disruption. Moreover, it is generally made of high thermal conductivity metal alloys, contributing to substantial thermal transmission at joints. This research aims to develop a novel frame-integrated unitised curtain wall system that will reduce thermal transmission at joints, reduce structural depth significantly and allow an inside flush finish. The idea is to adhesively bond a Fibre Reinforced Polymer (FRP) frame to the edge of the Insulated Glass Unit (IGU), thereby achieving composite structural behaviour and low thermal transmittance. The frame is to fit within the glazing cavity depth. Preliminary analytical structural and numerical thermal calculations are carried out to assess the performance of an initial schematic design. 4-point bending tests on GFRP and single-lap shear tests on bonded connections between GFRP and glass are performed to inform the frame and adhesive material selection process and to characterise these materials. Based on the preliminary calculations and experimental tests, some changes are put into effect to improve the performance of the system and mitigate potential issues. Structural and thermal numerical analysis carried out on the final detail design confirm a reduction of the structural depth to almost one fifth and a reduction of thermal transmission of 6% compared to a benchmark conventional system. A flush glazed appearance both to the inside and the outside are provided while keeping the full functionality of a unitised system.

Nonlinear seismic behaviour of concrete arch bridges

Arch bridge structural solution has been known for centuries, in fact the simple nature of arch that require low tension and shear strength was an advantage as the simple materials like stone and brick were the only option back in ancient centuries. By the pass of time especially after industrial revolution, the new materials were adopted in construction of arch bridges to reach longer spans. Nowadays one long span arch bridge is made of steel, concrete or combination of these two as "CFST", as the result of using these high strength materials, very long spans can be achieved. The current record for longest arch belongs to Chaotianmen bridge over Yangtze river in China with 552 meters span made of steel and the longest reinforced concrete type is Wanxian bridge which also cross the Yangtze river through a 420 meters span. Today the designer is no longer limited by span length as long as arch bridge is the most applicable solution among other approaches, i.e. cable stayed and suspended bridges are more reasonable if very long span is desired. Like any super structure, the economical and architectural aspects in construction of a bridge is extremely important, in other words, as a narrower bridge has better appearance, it also require smaller volume of material which make the design more economical. Design of such bridge, beside the high strength materials, requires precise structural analysis approaches capable of integrating the combination of material behaviour and complex geometry of structure and various types of loads which may be applied to bridge during its service life. Depend on the design strategy, analysis may only evaluates the linear elastic behaviour of structure or consider the nonlinear properties as well. Although most of structures in the past were designed to act in their elastic range, the rapid increase in computational capacity allow us to consider different sources of nonlinearities in order to achieve a more realistic evaluations where the dynamic behaviour of bridge is important especially in seismic zones where large movements may occur or structure experience P - _ effect during the earthquake. The above mentioned type of analysis is computationally expensive and very time consuming. In recent years, several methods were proposed in order to resolve this problem. Discussion of recent developments on these methods and their application on long span concrete arch bridges is the main goal of this research. Accordingly available long span concrete arch bridges have been studied to gather the critical information about their geometrical aspects and properties of their materials. Based on concluded information, several concrete arch bridges were designed for further studies. The main span of these bridges range from 100 to 400 meters. The Structural analysis methods implemented in in this study are as following: Elastic Analysis: Direct Response History Analysis (DRHA): This method solves the direct equation of motion over time history of applied acceleration or imposed load in linear elastic range. Modal Response History Analysis (MRHA): Similar to DRHA, this method is also based on time history, but the equation of motion is simplified to single degree of freedom system and calculates the response of each mode independently. Performing this analysis require less time than DRHA. Modal Response Spectrum Analysis (MRSA): As it is obvious from its name, this method calculates the peak response of structure for each mode and combine them using modal combination rules based on the introduced spectra of ground motion. This method is expected to be fastest among Elastic analysis. Inelastic Analysis: Nonlinear Response History Analysis (NL-RHA): The most accurate strategy to address significant nonlinearities in structural dynamics is undoubtedly the nonlinear response history analysis which is similar to DRHA but extended to inelastic range by updating the stiffness matrix for every iteration. This onerous task, clearly increase the computational cost especially for unsymmetrical buildings that requires to be analyzed in a full 3D model for taking the torsional effects in to consideration. Modal Pushover Analysis (MPA): The Modal Pushover Analysis is basically the MRHA but extended to inelastic stage. After all, the MRHA cannot solve the system of dynamics because the resisting force fs(u; u_ ) is unknown for inelastic stage. The solution of MPA for this obstacle is using the previously recorded fs to evaluate system of dynamics. Extended Modal Pushover Analysis (EMPA): Expanded Modal pushover is a one of very recent proposed methods which evaluates response of structure under multi-directional excitation using the modal pushover analysis strategy. In one specific mode,the original pushover neglect the contribution of the directions different than characteristic one, this is reasonable in regular symmetric building but a structure with complex shape like long span arch bridges may go through strong modal coupling. This method intend to consider modal coupling while it take same time of computation as MPA. Coupled Nonlinear Static Pushover Analysis (CNSP): The EMPA includes the contribution of non-characteristic direction to the formal MPA procedure. However the static pushovers in EMPA are performed individually for every mode, accordingly the resulted values from different modes can be combined but this is only valid in elastic phase; as soon as any element in structure starts yielding the neutral axis of that section is no longer fixed for both response during the earthquake, meaning the longitudinal deflection unavoidably affect the transverse one or vice versa. To overcome this drawback, the CNSP suggests executing pushover analysis for governing modes of each direction at the same time. This strategy is estimated to be more accurate than MPA and EMPA, moreover the calculation time is reduced because only one pushover analysis is required. Regardless of the strategy, the accuracy of structural analysis is highly dependent on modelling and numerical integration approaches used in evaluation of each method. Therefore the widely used Finite Element Method is implemented in process of all analysis performed in this research. In order to address the study, chapter 2, starts with gathered information about constructed long span arch bridges, this chapter continuous with geometrical and material definition of new models. Chapter 3 provides the detailed information about structural analysis strategies; furthermore the step by step description of procedure of all methods is available in Appendix A. The document ends with the description of results and conclusion of chapter 4.

Participación Directa y Aprendizaje de los Trabajadores en Mejoras Tecnológicas a Empresas Bajo Gestión Colectiva. Aplicación en Industrias Metalúrgicas de Venezuela y Argentina

La industria metalúrgica estatal venezolana ha vivido, desde sus inicios, procesos cíclicos de cambios y ajustes tecnológicos. Estos procesos no han sido objeto de sistematización que asegure el aprendizaje y apropiación del conocimiento. Este hecho, aún hoy, ha obstaculizado los procesos de apropiación y mejora de las tecnologías asociadas al sector. A partir del acompañamiento a iniciativas de participación de grupos de interés surgidos del seno de los trabajadores, se planteó esta investigación que tuvo como propósito la determinación de condiciones y relaciones para su participación directa en los procesos de mejora de las tecnologías existentes y el fortalecimiento del aprendizaje asociado. Se consideraron dos ámbitos Latinoamericanos donde hay manifestación de gestión colectiva y participación: Venezuela y Argentina. En el caso venezolano, el abordaje se realizó bajo la Investigación Acción Participativa (IAP), desarrollando la “investigación próxima”, como estrategia de acompañamiento, mediante “talleres de formación-investigación” y la sistematización de experiencias considerando la perspectiva y necesidades de los actores. En el caso argentino, el abordaje se realizó mediante visitas, entrevistas, reuniones y encuentros. Los talleres realizados en Venezuela, en un contexto de diálogo de saberes, facilitaron el surgimiento de herramientas prácticas para la sistematización de su propia experiencia (“Preguntas generadoras”, “Mi historia con la tecnología”, “Bitácora de aprendizaje”). El intercambio con los pares argentinos ha generado una red que plantea la posibilidad de construcción y nucleación conjunta de saberes y experiencia, tanto para los trabajadores como para los investigadores. Los casos estudiados referidos a las empresas recuperadas por los trabajadores (ERTs) argentinos evidencian un proceso de participación marcada por su autonomía en la gestión de la empresa, dadas las circunstancias que los llevó a asumirla para conservar sus puestos de trabajo. De estos casos emergieron categorías asociadas con elementos de gestión de un proceso técnico–tecnológico, como la participación en la planificación, concepción o diseño de la mejora. La participación en general está asociada al hecho asambleario, vinculado a las prácticas de toma de decisiones autogestionarias como expresión de una alta participación. La Asamblea, como máxima instancia de participación, y el Consejo de Administración son las formas de participación prevalecientes. En cuanto al aprendizaje, los trabajadores de las ERTs argentinas aportaron categorías de gran significación a los procesos de socialización del conocimiento: conocimiento colectivo y cooperación del conocimiento, rescate de los saberes y formación de trabajadores que tomen el relevo. Las categorías surgidas de las ERTs argentinas, los referentes teóricos y el interés de los trabajadores venezolanos fueron la base para la valoración tanto de su grado de participación en las mejoras a procesos tecnológicos emprendidas, como del aprendizaje asociado. Ésta valoración se realizó bajo una aproximación borrosa dado el carácter ambiguo de estas categorías que fueron trabajadas como conjuntos que se relacionan, más que como variables. Se encontró que la participación, se configura como un sub-conjunto del aprendizaje para contribuir a su fortalecimiento. Las condiciones y relaciones para fortalecer la participación en los asuntos tecnológicos surgieron a partir de la sistematización y síntesis de ambas experiencias (Venezuela y Argentina) conjugando una estructura que contempla la formación para la nucleación de colectivos de saberes (proyectos de mejora o innovaciones), las redes por afinidad, la sistematización de su propia experiencia técnica y los enlaces institucionales. Estos resultados dan cuenta de la integración de los intereses de las partes (trabajadores, investigadores, instituciones), mediante las estrategias de encuentro, de sistematización de los propios métodos y de conformación de los “colectivos de saberes”, la red de IAP en la industria (IAP Industrial) considerando la “deriva de la investigación”, bajo discursos práctico–teóricos propios, como posibilidad de posicionamiento de su participación en los asuntos tecnológicos de sus respectivas organizaciones, abriendo una oportunidad de ampliación de la experiencia en otros ámbitos y sectores. ABSTRACT Venezuelan's state owned steel industry has experienced since its earliest years, cycles of change and technological adjustments. These processes have not been systematized to ensure learning and knowledge in those organizations. This fact, even today, has hindered the processes of appropriation and improving the technologies associated with the sector. In order to support initiatives involving metalworker interest groups, this research was aimed at determining conditions and relations for their direct participation in process improvements to existing technologies and strengthening the associated learning. Two Latin American countries, Venezuela and Argentina, were considered on the base of their collective management and participation experiences. The Venezuelan approach was carried out under the Participatory Action Research (PAR) strategy, through the ‘proximal research’ as support strategy, by means of ‘workshops–research’ and systematization of experiences considering the perspective and needs of actors. Workshops were carried out in metallurgical enterprises from steel and aluminum at Guayana, Venezuela and its affiliates in the Central region. Those industries have been promoted collective management. The Argentine approach was carried out through visits, interviews, meetings and gatherings. The workshops held in Venezuela, in a dialogue of knowledge context, facilitated the emergence of tools for the systematization of their own experience (‘generating questions’, ‘My history with technology’, ‘Learning Log’). The relation with Argentine peers has generated a network that creates opportunities of knowledge and experience construction and its nucleation for both, workers and researchers. The cases studied relating to Argentine workers’ recuperated enterprises show a participatory process marked by autonomy in the management of the factory, given the circumstances that led them to take it in order to maintain their jobs. From these cases emerged categories associated with management aspects about technical-technology process, such as participation in planning, design or implementation of the improvement. Participation, in general, is associated with assemblies, joined to the practices of self-management decision-making as an expression of a high participation. The Cooperative General Assembly, as the highest instance of participation, and the Board of Directors are the prevalent forms of participation. In relation to learning, Argentine workers’ recuperated enterprises provided categories of great significance to the process of socialization of knowledge: collective knowledge and knowledge cooperation, recovery of knowledge and training workers for replacement. Based on categories arising from the Argentine experience, theoretical framework and the interest of the Venezuelan workers the assessment of both, their degree of participation on technical improvements and the associated technological learning were made considering a fuzzy approach, given the ambiguous nature of these categories that were worked as sets rather than variables. It was found that participation is configured as a subset of learning to contribute to its strengthening. The conditions and relations to strengthen participation in technology issues emerged from the systematization and synthesis of both experiences (Venezuela and Argentina) combining a structure which provides training for the nucleation of collectives of knowledge (improvement projects or innovations), affinity networks, systematization of their own expertise and institutional links. These results show the integration of the interests of stakeholders (workers, researchers, institutions) through strategies like meetings, systematization of their own methods, forming ‘collectives of technological knowledge’ and a participative action research network in this industry (Industrial PAR) considering the ‘research drift’, under their own practical-theoretical discourses positioned as a possibility of their participation in technological activities in their respective organizations, opening an opportunity for scaling to other areas and sectors.

Diseño y evaluación de un procedimiento on-line para la biorremediación de aguas radiactivas en centrales nucleares

Recientemente se ha demostrado la existencia de microorganismos en las piscinas de almacenamiento de combustible nuclear gastado en las centrales nucleares utilizando técnicas convencionales de cultivo en el laboratorio. Estudios posteriores han puesto de manifiesto que los microorganismos presentes eran capaces de colonizar las paredes de acero inoxidable de las piscinas formando biopelículas. Adicionalmente se ha observado la capacidad de estas biopelículas de retener radionúclidos, lo que hace pensar en la posibilidad de utilizarlas en la descontaminación de las aguas radiactivas de las piscinas. En la presente tesis se plantea conocer más profundamente la biodiversidad microbiana de las biopelículas utilizando técnicas de biología molecular como la clonación, además de desarrollar un sistema de descontaminación a escala piloto con el objetivo de valorar si el proceso podría resultar escalable a nivel industrial. Para ello se diseñaron y fabricaron dos biorreactores en acero inoxidable compatibles con las condiciones específicas de seguridad sísmica y protección frente a la radiación en la zona controlada de una central nuclear. Los biorreactores se instalaron en la Central Nuclear de Cofrentes (Valencia) en las proximidades de las piscinas de almacenamiento de combustible nuclear gastado y precediendo a las resinas de intercambio iónico, de forma que reciben el agua de las piscinas permitiendo el análisis in situ de la radiación eliminada del agua de las mismas. Se conectó una lámpara de luz ultravioleta a uno de los biorreactores para poder comparar el desarrollo de bipelículas y la retención de radiactividad en ambas condiciones. En estos biorreactores se introdujeron ovillos de acero inoxidable y de titanio que se extrajeron a diversos tiempos, hasta 635 días para los ovillos de acero inoxidable y hasta 309 días para los ovillos de titanio. Se analizaron las biopelículas desarrolladas sobre los ovillos por microscopía electrónica de barrido y por microscopía de epifluorescencia. Se extrajo el ADN de las biopelículas y, tras su clonación, se identificaron los microorganismos por técnicas independientes de cultivo. Asimismo se determinó por espectrometría gamma la capacidad de las biopelículas para retener radionúclidos. Los microorganismos radiorresistentes identificados pertenecen a los grupos filogenéticos Alpha-proteobacteria, Gamma-proteobacteria, Actinobacteria, Deinococcus-Thermus y Bacteroidetes. Las secuencias de estos microorganismos se han depositado en el GenBank con los números de acceso KR817260-KR817405. Se ha observado una distribución porcentual ligeramente diferente en relación con el tipo de biorreactor. Las biopelículas han retenido fundamentalmente radionúclidos de activación. La suma de Co-60 y Mn-54 ha llegado en ocasiones al 97%. Otros radionúclidos retenidos han sido Cr-51, Co-58, Fe-59, Zn-65 y Zr-95. Se sugiere un mecanismo del proceso de retención de radionúclidos relacionado con el tiempo de formación y desaparición de las biopelículas. Se ha valorado que el proceso escalable puede ser económicamente rentable. ABSTRACT The existence of microorganisms in spent nuclear fuel pools has been demonstrated recently in nuclear power plants by using conventional microbial techniques. Subsequent studies have revealed that those microorganisms were able to colonize the stainless steel pool walls forming biofilms. Additionally, it has been observed the ability of these biofilms to retain radionuclides, which suggests the possibility of using them for radioactive water decontamination purposes. This thesis presents deeper knowledge of microbial biofilms biodiversity by using molecular biology techniques such as cloning, and develops a decontamination system on a pilot scale, in order to assess whether the process could be scalable to an industrial level. Aiming to demonstrate this was feasible, two stainless steel bioreactors were designed and manufactured, both were compatible with seismic and radiation protection standards in the controlled zone of a nuclear plant. These bioreactors were installed in the Cofrentes Nuclear Power Plant (Valencia) next to the spent nuclear fuel pools and preceding (upstream) ion exchange resins. This configuration allowed the bioreactors to receive water directly from the pools allowing in situ analysis of radiation removal. One ultraviolet lamp was connected to one of the bioreactors to compare biofilms development and radioactivity retention in both conditions. Stainless steel and titanium balls were introduced into these bioreactors and were removed after different time periods, up to 635 days for stainless steel balls and up to 309 days for titanium. Biofilms developed on the balls were analyzed by scanning electron microscopy and epifluorescence microscopy. DNA was extracted from the biofilms, was cloned and then the microorganisms were identified by independent culture techniques. Biofilms ability to retain radionuclides was also determined by gamma spectrometry. The identified radioresistant organisms belong to the phylogenetic groups Alphaproteobacteria, Gamma-proteobacteria, Actinobacteria, Deinococcus-Thermus and Bacteroidetes. The sequences of these microorganisms have been deposited in GenBank (access numbers KR817260-KR817405). A different distribution of microorganisms was observed in relation to the type of bioreactor. Biofilms have essentially retained activation radionuclides. Sometimes the sum of Co-60 and Mn-54 reached 97%. Cr-51, Co-58, Fe-59, Zn-65 and Zr-95 have also been retained. A radionuclide retention process mechanism related to biofilms formation and disappearance time is suggested. It has been assessed that the scalable process can be economically profitable.