Influence of different sanitizers on food contaminant bacteria: effect of exposure temperature, contact time, and product concentration

The efficiency of four Sanitizers - peracetic acid, chlorhexidine, quaternary ammonium, and organic acids - was tested in this work using different bacteria recognized as a problem to meat industry, Salmonella sp., S. aureus, E. coli and L. monocytogenes. The effects of sanitizer concentration (0.2, 0.5, 0.6, 1.0, 1.1 and 1.4%), at different temperatures (10 and 45 °C) and contact time (2, 10, 15, 18 and 25 minutes) were evaluated. Tests in an industrial plant were also carried out considering previously obtained results. In a general way, peracetic acid presented higher efficiencies using low concentration (0.2%) and contact time (2 minutes) at 10 °C. The tests performed in industrial scale showed that peracetic acid presented a good performance in concentration and contact time lower than that suggested by the suppliers. The use of chlorhexidine and quaternary ammonium led to reasonable results at the indicated conditions, and organic acids were ineffective under concentration and contact time higher than those indicated by the suppliers in relation to Staphylococcus aureus. The results, in general, show that the choice for the most adequate sanitizer depends on the microorganism contaminant, the time available for sanitizer application, and also on the process cost.

Energy efficiency and moisture diffusivity of apple slices during convective drying

Abstract The present study aimed at investigating the influences of drying air temperature and flow rate on energy parameters and dehydration behaviour of apple slices. For this purpose, apple slices were dried in a convective dryer at air temperatures of 50, 60 and 70 °C, and air velocities of 1, 1.5 and 2 m s–1. Dehydration rate increased as the air temperature and flow rate increased from 50 to 70 °C and 1 to 2 m s–1, respectively. The effective moisture diffusivity was determined to be in the range of 6.75×10–10-1.28×10–9 m2 s–1. Results of data analysis showed that the maximum energy consumption (23.94 kW h) belonged to 50 °C and 2 m s–1 and the minimum (13.89 kW h) belonged to 70 °C and 1 m s–1 treatment. Energy efficiency values were in the range of 2.87-9.11%. Moreover, the results indicated that any increment in the air temperature increases thermal and drying efficiencies while any increment in the air flow rate decreases both of them.

Production of magnesium carbonates from serpentinites for CO2 mineral sequestration : optimisation towards industrial application

Global warming is one of the most alarming problems of this century. Initial scepticism concerning its validity is currently dwarfed by the intensification of extreme weather events whilst the gradual arising level of anthropogenic CO2 is pointed out as its main driver. Most of the greenhouse gas (GHG) emissions come from large point sources (heat and power production and industrial processes) and the continued use of fossil fuels requires quick and effective measures to meet the world’s energy demand whilst (at least) stabilizing CO2 atmospheric levels. The framework known as Carbon Capture and Storage (CCS) – or Carbon Capture Utilization and Storage (CCUS) – comprises a portfolio of technologies applicable to large‐scale GHG sources for preventing CO2 from entering the atmosphere. Amongst them, CO2 capture and mineralisation (CCM) presents the highest potential for CO2 sequestration as the predicted carbon storage capacity (as mineral carbonates) far exceeds the estimated levels of the worldwide identified fossil fuel reserves. The work presented in this thesis aims at taking a step forward to the deployment of an energy/cost effective process for simultaneous capture and storage of CO2 in the form of thermodynamically stable and environmentally friendly solid carbonates. R&D work on the process considered here began in 2007 at Åbo Akademi University in Finland. It involves the processing of magnesium silicate minerals with recyclable ammonium salts for extraction of magnesium at ambient pressure and 400‐440⁰C, followed by aqueous precipitation of magnesium in the form of hydroxide, Mg(OH)2, and finally Mg(OH)2 carbonation in a pressurised fluidized bed reactor at ~510⁰C and ~20 bar PCO2 to produce high purity MgCO3. Rock material taken from the Hitura nickel mine, Finland, and serpentinite collected from Bragança, Portugal, were tested for magnesium extraction with both ammonium sulphate and bisulphate (AS and ABS) for determination of optimal operation parameters, primarily: reaction time, reactor type and presence of moisture. Typical efficiencies range from 50 to 80% of magnesium extraction at 350‐450⁰C. In general ABS performs better than AS showing comparable efficiencies at lower temperature and reaction times. The best experimental results so far obtained include 80% magnesium extraction with ABS at 450⁰C in a laboratory scale rotary kiln and 70% Mg(OH)2 carbonation in the PFB at 500⁰C, 20 bar CO2 pressure for 15 minutes. The extraction reaction with ammonium salts is not at all selective towards magnesium. Other elements like iron, nickel, chromium, copper, etc., are also co‐extracted. Their separation, recovery and valorisation are addressed as well and found to be of great importance. The assessment of the exergetic performance of the process was carried out using Aspen Plus® software and pinch analysis technology. The choice of fluxing agent and its recovery method have a decisive sway in the performance of the process: AS is recovered by crystallisation and in general the whole process requires more exergy (2.48–5.09 GJ/tCO2sequestered) than ABS (2.48–4.47 GJ/tCO2sequestered) when ABS is recovered by thermal decomposition. However, the corrosive nature of molten ABS and operational problems inherent to thermal regeneration of ABS prohibit this route. Regeneration of ABS through addition of H2SO4 to AS (followed by crystallisation) results in an overall negative exergy balance (mainly at the expense of low grade heat) but will flood the system with sulphates. Although the ÅA route is still energy intensive, its performance is comparable to conventional CO2 capture methods using alkanolamine solvents. An energy‐neutral process is dependent on the availability and quality of nearby waste heat and economic viability might be achieved with: magnesium extraction and carbonation levels ≥ 90%, the processing of CO2‐containing flue gases (eliminating the expensive capture step) and production of marketable products.

Characterization and Investigation on Material Compatibilities of Building Integrated Photovoltaic Module Components

Building Integrated Photovoltaics (BIPV) are considered as the future of photovoltaic (PV) technology. The advantage of BIPV system is its multi-functionality; they fulfil the functions of a building envelope with the added benefit of generating power by replacing the traditional roofing and façade materials with PV that generate power. In this thesis, different types of PV cells and modules have been described in detail with their efficiencies and usage trends in the last decade. The different BIPV products for roof and façade are discussed in detail giving several examples. The electricity generation potential of BIPV in selected countries is compared with their actual electricity consumption. Further, the avoided greenhouse gas (GHG) emissions associated with electricity generation from traditional sources and transportation and distribution (T&D) losses are calculated. The results illustrate huge savings in GHGs. In BIPV different types of façade and backsheets are used. In this thesis, selected backsheets and façade were characterized in terms of their surface structure identification using infrared spectroscopy (FTIR-ATR), scanning electron microscopy with energy dispersive X-ray (SEM-EDX) and physical characterization using surface energy measurements. By using FTIR-ATR, surface polymeric materials were identified and with SEM-EDX, identification of the surface elements was possible. Surface energy measurements were useful in finding the adhesives and knowing the surface energies of the various backsheets and façade. The strength of adhesion between the facade and backsheets was studied using peel test. Four different types of adhesives were used to study the fracture pattern and peel tests values to identify the most suitable adhesive. It was found out that pretreatment increased the adhesive strength significantly.

A high efficiency microturbine concept

There is a growing trend towards decentralized electricity and heat production throughout the world. Reciprocating engines and gas turbines have an essential role in the global decentralized energy markets and any improvement in their electrical efficiency has a significant impact from the environmental and economic viewpoints. This paper introduces an inter-cooled and recuperated two-shaft microturbine at 500 kW electric output range. The microturbine is optimized for a realistic combination of the turbine inlet temperature, the recuperation rate and the pressure ratio. The new microturbine design aims to achieve significantly increased performance within the range of microturbines and even competing with the efficiencies achieved in large industrial gas turbines. The simulated electrical efficiency is 45%. Improving the efficiency of combined heat and power (CHP) systems will significantly decrease the emissions and operating costs of decentralized heat and electricity production. Cost-effective, compact and environmentally friendly micro-and small-scale CHP turbine systems with high electrical efficiency will have an opportunity to successfully compete against reciprocating engines, which today are used in heat and power generation all over the world and manufactured in large production series. This paper presents a small-scale gas turbine process, capable of competing with reciprocating engine in terms of electrical efficiency.

Neoliberalism and global capital mobility: a necessary reconsideration of textbook trade theory

Textbook theory ignores capital flows: trade determines exchange rates and specialisation. Approaches taking the effects of capital movements adequately into account are needed, and a new theory of economic policy including measures to protect the real economy from external volatility. Equilibrating textbook mechanisms cannot work unless trade-caused surpluses and deficits set exchange rates. To allow orthodox trade theory to work one must hinder capital flows from destroying its very basis, which the IMF and wrong regulatory decisions have done, penalising production and trade. A new, real economy based theory is proposed, a Neoclassical agenda of controlling capital flows and speculation.

Oxidation of Aqueous Thiosulfate Solutions by Pulsed Corona Discharge

The aim of this Master’s thesis focused on the oxidation of sodium thiosulfate using non thermal plasma technology as an advance oxidation process (AOP). By using this technology we can degrade certain toxic chemical compounds present in mining wastewaters as pollutants. Different concentrations of thiosulfate and pulse frequencies were used in the PCD experiments and the results in terms of various delivered energies (kWh/m3) and degradation kinetics were compared. Pulsed corona discharge is an energy efficient process compared to other oxidation processes using for the treatment of waste water pollutants. Due to its simplicity and low energy costs make it attractive in the field of waste water treatment processes. This technology of wastewater treatment has been tested mainly on pilot scale level and in future the attempts are to be focus on PCD investigations on larger process scale. In this research work of oxidation of thiosulfate using pulsed corona discharge, the main aim of this research was to study degradation of a studied toxic and not environmental friendly chemical compound. The focus of this research was to study the waste waters coming from the gold mines containing leachate compound thiosulfate. Literature review contained also gold leaching process when cyanide is used as the leachate. Another objective of this work was to compare PCD process with other processes based on their energy efficiencies. In the experimental part two concentrations of sodium thiosulfate, 1000ppm and 400ppm, were used. Two pulse generator frequencies of 833 and 200 pulses per second (pps) were used. The chemical analyses of the samples taken during semi-batch PCD oxidation process were analyzed by ion chromatographic (IC). It is observed after the analyses that among different frequencies and concentrations, the most suitable ones for the process is 200pps and 1000ppm respectively because the pollutants present in the waste water has more time to react with the OH radicals which are the oxidants and the process is energy efficient compared to other frequencies.

The role of import intermediary companies in the Russian imports from the EU A case study of a Russian industrial company’s point of view on import intermediaries

The literature on agency suggests different implications for the use of export intermediaries. However, only few studies provide a view on import intermediaries. This thesis tries for its part to fill this research gap by studying the import intermediaries in the EU–Russia trade from a Russian industrial company’s point of view. The aim is to describe import intermediation and explain the need for import intermediary companies in the EU–Russia trade. The theoretical framework of this thesis originates from an article by Peng and York (2001), in which they study the performance of export intermediaries. This thesis applies resource-based theory, transaction cost theory and agency cost theory, following the idea of Peng and York. The resource-based theory approach is utilised for describing an ideal import intermediary company, and transaction cost theory provides a basis for understanding the benefits of using the services of import intermediary companies, while agency cost theory is applied in order to understand the risks the Russian industrial company faces when it decides to use the services of import intermediaries. The study is performed in the form of a case interview with a representative of a major Russian metallurgy company. The results of the study suggest that an ideal intermediary has the skills required specifically for the imports process, in order to save time and money of the principal company. The intermediary company helps reducing the amount of time the managers and the staff of the principal company use to make imports possible, thus reducing the salary costs and providing the possibility to concentrate on the company’s core competencies. The benefits of using the services of import intermediary companies are the reduced transaction costs, especially salary costs that are minimised because of the effectiveness and specialisation of import intermediaries. Intermediaries are specialised in the imports process and thus need less time and resources to organise the imports. They also help to reduce the fixed salary costs, because their services can be used only when needed. The risks of being misled by intermediaries are minimised by the competition on the import intermediary market. In case an intermediary attempts fraud, it gets replaced by its rival.

Design and Material Selection of High-Speed Rotating Electrical Machines

The increasing emphasis on energy efficiency is starting to yield results in the reduction in greenhouse gas emissions; however, the effort is still far from sufficient. Therefore, new technical solutions that will enhance the efficiency of power generation systems are required to maintain the sustainable growth rate, without spoiling the environment. A reduction in greenhouse gas emissions is only possible with new low-carbon technologies, which enable high efficiencies. The role of the rotating electrical machine development is significant in the reduction of global emissions. A high proportion of the produced and consumed electrical energy is related to electrical machines. One of the technical solutions that enables high system efficiency on both the energy production and consumption sides is high-speed electrical machines. This type of electrical machines has a high system overall efficiency, a small footprint, and a high power density compared with conventional machines. Therefore, high-speed electrical machines are favoured by the manufacturers producing, for example, microturbines, compressors, gas compression applications, and air blowers. High-speed machine technology is challenging from the design point of view, and a lot of research is in progress both in academia and industry regarding the solution development. The solid technical basis is of importance in order to make an impact in the industry considering the climate change. This work describes the multidisciplinary design principles and material development in high-speed electrical machines. First, high-speed permanent magnet synchronous machines with six slots, two poles, and tooth-coil windings are discussed in this doctoral dissertation. These machines have unique features, which help in solving rotordynamic problems and reducing the manufacturing costs. Second, the materials for the high-speed machines are discussed in this work. The materials are among the key limiting factors in electrical machines, and to overcome this limit, an in-depth analysis of the material properties and behavior is required. Moreover, high-speed machines are sometimes operating in a harsh environment because they need to be as close as possible to the rotating tool and fully exploit their advantages. This sets extra requirements for the materials applied.

Investigations into phosphorus removal by constructed wetlands : root bed media modifications /

A study has been conducted focusing on how the phosphorus renrx)val efficiency of a constructed wetland (CW) can be optimized through the selective enrichment of the substratum. Activated alumina and powdered iron were examined as possible enrichment compounds. Using packed glass column trials it was found that alumina was not suitable for the renx)val of ortho-phosphate from solution, while mixtures of powdered iron and quartz sand proved to be very efficient. The evaluation of iron/sand mixtures in CWs planted with cattails was performed in three stages; first using an indoor lab scale wetland, then an outdoor lab scale wetland, and finally in a small scale pilot project. For the lab scale tests, three basic configurations were evaluated: using the iron/sand as a pre-filter, in the root bed. and as a post filter. Primary lagoon effluent was applied to the test cells to simulate actual CW conditions, and the total phosphorus and iron concentrations of the influent and effluent were nfK)nitored. The pilot scale trials were limited to using only a post filter design, due to in-progress research at the pilot site. The lab scale tests achieved average renrK>val efficiencies greater than 91% for all indoor configurations, and greater than 97% for all outdoor configurations. The pilot scale tests had an average renK)val efficiency of 60%. This relatively low efficiency in the pilot scale can be attributed to the post filters being only one tenth the size of the lab scale test in terms of hydraulic loading (6 cm/day vs. 60 cm/day).

The Elucidation of the involvement of endonuclease DNase y in reducing DNA transfection efficiency in mammalian cells

Gene therapy is predicated upon efficient gene transfer. While viral vectors are the method of choice for transformation efficiency, the immunogenicity and safety concerns remain problematic. Non-viral vectors, on the other hand, have shown high degrees of safety and are mostly non-immunogenic in nature. However, non-viral vectors usually suffer from low levels oftransformation efficiency and transgene expression. Thus, increasing transformation efficiency ofnon-viral vectors, in particular by calcium phosphate co-precipitation technique, is a way of generating a suitable vector for gene therapy and is the aim of this study. It is a long known fact that different cell lines have different transfection efficiencies regardless oftransfection methodology (Lin et a!., 1994). Using commonly available cell lines Madine-Darby Bovine Kidney (MDBK), HeLa and Human Embryonic Kidney (HEK-293), we have shown a decreasing trend ofDNase activity based on a plasmid digestion assay. From densitometry studies, as much as a 40% reduction in DNase activity was observed when comparing HEK-293 (least active) to MDBK (most active). Using various biochemical assays, it was determined that DNase y, in particular, was expressed more highly in MDBK cells than both HeLa and HEK-293. Upon cloning of the bovine DNase y gene, we utilized the sequence information to construct antisense expressing plasmids via both traditional antisense RNA (pASDGneoM) and siRNA (psiRNA-S4, psiRNA-S11 and psiRNA-S16). For the construction ofpASDGneoM, the 3' end of the DNase y was inserted in opposite orientation under a cytomegalovirus (CMV) promoter such that the expression ofRNA complementary to the DNase 2 ymRNA occurred. For siRNA plasmids, the sequence was screened to yield optimal short sequences for siRNA inhibition. The silencing ofbovine DNase y led to an increase in transfection efficiency based on traditional calcium phosphate co-precipitation technique; stable clones of siRNA-producing MDBK cell lines (psiRNA-S4 Bland psiRNA-S4 B4) both demol).strated 4-fold increases in transfection efficiency. Furthermore, serial transfection of antisense DNase y plasmid pASDGneoM and reporter pCMV-~ showed a maximum of 8-fold increase in transfection efficiency when the two separate transfections were carried out 4 hours apart (i.e. transfection ofpASDGneoM, separated by four hours, then transfection ofpCMV-~). Together, these results demonstrate the involvement ofDNase y in reducing transfection efficiency, at least by traditional calcium phosphate technique.

Development of techniques for testing the effect of the E1 region on adenovirus integration /

Adenoviral vectors are currently the most widely used gene therapeutic vectors, but their inability to integrate into host chromosomal DNA shortened their transgene expression and limited their use in clinical trials. In this project, we initially planned to develop a technique to test the effect of the early region 1 (E1) on adenovirus integration by comparing the integration efficiencies between an E1-deleted adenoviral vector (SubE1) and an Elcontaining vector (SubE3). However, we did not harvest any SubE3 virus, even if we repeated the transfection and successfully rescued the SubE1 virus (2/4 transfections generated viruses) and positive control virus (6/6). The failure of rescuing SubE3 could be caused by the instability of the genomic plasmid pFG173, as it had frequent intemal deletions when we were purifying It. Therefore, we developed techniques to test the effect of E1 on homologous recombination (HR) since literature suggested that adenovirus integration is initiated by HR. We attempted to silence the E1 in 293 cells by transfecting E1A/B-specific small interfering RNA (siRNA). However, no silenced phenotype was observed, even if we varied the concentrations of E1A/B siRNA (from 30 nM to 270 nM) and checked the silencing effects at different time points (48, 72, 96 h). One possible explanation would be that the E1A/B siRNA sequences are not potent enough to Induce the silenced phenotype. For evaluating HR efficiencies, an HR assay system based on bacterial transfonmatJon was designed. We constmcted two plasmids ( designated as pUC19-dl1 and pUC19-dl2) containing different defective lacZa cassettes (forming white colonies after transformation) that can generate a functional lacZa cassette (forming blue colonies) through HR after transfecting into 293 cells. The HR efficiencies would be expressed as the percentages of the blue colonies among all the colonies. Unfortunately, after transfonnation of plasmid isolated from 293 cells, no colony was found, even at a transformation efficiency of 1.8x10^ colonies/pg pUC19, suggesting the sensitivity of this system was low. To enhance the sensitivity, PCR was used. We designed a set of primers that can only amplify the recombinant plasmid fomied through HR. Therefore, the HR efficiencies among different treatments can be evaluated by the amplification results, and this system could be used to test the effect of E1 region on adenovirus integration. In addition, to our knowledge there was no previous studies using PCR/ Realtime PCR to evaluate HR efficiency, so this system also provides a PCR-based method to carry out the HR assays.

Factors affecting DNA uptake by mammalian cells

The ability to introduce DNA and express custom DNA sequences in bacteria opened the door for improvements in a large number of fields including agriculture, pharmacology, medicine, nutrition, etc. The ability to introduce foreign DNA sequences into mammalian cells in an efficient manner would have a large impact on therapeutic applications especially gene therapy. The methods in use today suffer from low efficiencies and sometimes toxicity. In this work a number of factors were evaluated for their effect onONA uptake efficiency. The factors studied included exposure to sublethal concentration of hydrogen peroxide which have been show to lead to destabilisation ofthe lysosomes. These exposures have proven to be very toxic to cells when combined with either the calcium phosphate or the lipofectAMINE® transfection methods. Another factor evaluated was exposure to Electro-Magnetic Fields (EMF). This was fuelled by the fact that EMF have been shown to mediate a number of effects on cell structure and/or physiology. EMF exposure by itself was not sufficient to induce the cells to pick up the DNA, therefore its effect on calcium phosphate and lipofectAMINE® was tested. Although some positive results were obtained, the variability of these results exceeded by far any observed enhancements which discouraged any further work on EMF. Also tested was the possible effect the presence of the cytomegalovirus (CMV) sequence might have on DNA uptake (based on previous results in this lab). It was found that the presence ofCMV in the DNA sequence does not enhance uptake or slow down degradation of the internalised DNA. The final factor tested was the effect of basic amino acids on transfection efficiency. It was found that arginine can enhance DNA uptake by about 170% v/ith calcium phosphate and about 200% with LipofectAMINE®. A model was proposed to explain the effect of arginine as well as the lack of effect from other amino acids.

Development and characterization of concentric capillary nebulizer used in inductively coupled plasma analysis /

A simple, low-cost concentric capillary nebulizer (CCN) was developed and evaluated for ICP spectrometry. The CCN could be operated at sample uptake rates of 0.050-1.00 ml min'^ and under oscillating and non-oscillating conditions. Aerosol characteristics for the CCN were studied using a laser Fraunhofter diffraction analyzer. Solvent transport efficiencies and transport rates, detection limits, and short- and long-term stabilities were evaluated for the CCN with a modified cyclonic spray chamber at different sample uptake rates. The Mg II (280.2nm)/l\/lg 1(285.2nm) ratio was used for matrix effect studies. Results were compared to those with conventional nebulizers, a cross-flow nebulizer with a Scott-type spray chamber, a GemCone nebulizer with a cyclonic spray chamber, and a Meinhard TR-30-K3 concentric nebulizer with a cyclonic spray chamber. Transport efficiencies of up to 57% were obtained for the CCN. For the elements tested, short- and long-term precisions and detection limits obtained with the CCN at 0.050-0.500 ml min'^ are similar to, or better than, those obtained on the same instrument using the conventional nebulizers (at 1.0 ml min'^). The depressive and enhancement effects of easily ionizable element Na, sulfuric acid, and dodecylamine surfactant on analyte signals with the CCN are similar to, or better than, those obtained with the conventional nebulizers. However, capillary clog was observed when the sample solution with high dissolved solids was nebulized for more than 40 min. The effects of data acquisition and data processing on detection limits were studied using inductively coupled plasma-atomic emission spectrometry. The study examined the effects of different detection limit approaches, the effects of data integration modes, the effects of regression modes, the effects of the standard concentration range and the number of standards, the effects of sample uptake rate, and the effect of Integration time. All the experiments followed the same protocols. Three detection limit approaches were examined, lUPAC method, the residual standard deviation (RSD), and the signal-to-background ratio and relative standard deviation of the background (SBR-RSDB). The study demonstrated that the different approaches, the integration modes, the regression methods, and the sample uptake rates can have an effect on detection limits. The study also showed that the different approaches give different detection limits and some methods (for example, RSD) are susceptible to the quality of calibration curves. Multicomponents spectral fitting (MSF) gave the best results among these three integration modes, peak height, peak area, and MSF. Weighted least squares method showed the ability to obtain better quality calibration curves. Although an effect of the number of standards on detection limits was not observed, multiple standards are recommended because they provide more reliable calibration curves. An increase of sample uptake rate and integration time could improve detection limits. However, an improvement with increased integration time on detection limits was not observed because the auto integration mode was used.

Polyglutamine monomer structure and its implications for molecular self-assembly

Polyglutamine is a naturally occurring peptide found within several proteins in neuronal cells of the brain, and its aggregation has been implicated in several neurodegenerative diseases, including Huntington's disease. The resulting aggregates have been demonstrated to possess ~-sheet structure, and aggregation has been shown to start with a single misfolded peptide. The current project sought to computationally examine the structural tendencies of three mutant poly glutamine peptides that were studied experimentally, and found to aggregate with varying efficiencies. Low-energy structures were generated for each peptide by simulated annealing, and were analyzed quantitatively by various geometry- and energy-based methods. According to the results, the experimentally-observed inhibition of aggregation appears to be due to localized conformational restraint placed on the peptide backbone by inserted prolines, which in tum confines the peptide to native coil structure, discouraging transition towards the ~sheet structure required for aggregation. Such knowledge could prove quite useful to the design of future treatments for Huntington's and other related diseases.