Microstructure, crystalline phase, and dielectric property analyses of TiO2 composition with ZrO2 addition

For microwave applications, including mobile and satellite communications, ceramic resonators should have a high dielectric constant, low dielectric losses, and high frequency stability. In this sense, TiO2-ZrO 2 ceramics have been investigated as a function of sintering behavior, phase composition, and microstructure. The ceramics were densified reaching a value of about 86% of theoretical density at 1400°C sintering temperature. The ceramics are prepared by mixing raw materials with the following TiO2-ZrO2 weight % ratio: 100 to 0, 90 to 10, and 80 to 20, respectively. The measured dielectric constants are between 79 and 88 values, while the quality factor due to dielectric losses are between 2820 and 5170. These results point out the influence of Ti/Zr ratio on controlling the dielectric properties. © (2010) Trans Tech Publications.

Sensory profile and preference mapping of orange cakes with addition of prebiotics inulin and oligofructose

Orange cakes with addition of inulin and oligofructose to justify a prebiotic claim (minimum of 3 g of fructans in a 60 g serving of cake) were investigated regarding sensory aspects. The sensory profile of cakes with inulin, with inulin/oligofructose and without prebiotics (standard cake) was evaluated using descriptive quantitative analysis. Preference mapping was assessed using multidimensional scaling on data obtained through an acceptability test with a nine-point hedonic scale. The cakes with prebiotics presented greater crust brownness, dough beigeness, hardness and stickiness than the standard cake and lower crumbliness. Principal Component Analysis (69.5 and 10.7% of explanation to the first and second principal components, respectively) showed that crust brownness, dough beigeness, hardness and stickiness contributed to distinguish the cakes with prebiotics from standard cakes. The sensory acceptability was similar for the three cakes and higher when compared to three commercial cakes, but the preference mapping showed that cakes with prebiotics were preferred to commercial cakes. Addition of prebiotics in orange cakes is feasible, based on the sensory results, which may facilitate marketing of this functional food with sensorial qualities equivalent to conventional products. © 2012 Elsevier Ltd.

Effect of seed addition on SnO2-based varistors for low voltage application

The effect of seed addition on the microstructure and non-ohmic properties of the SnO2 + 1%CoO + 0.05%Nb2O5 ceramic-based system was analyzed. Two classes of seeds were prepared: 99% SnO2 + 1%CuO and 99% SnO2 + 1%CoO (mol%); both classes were added to the ceramic-based system in the amount of 1%, 5%, and 10%. The two systems containing 1% of seeds resulted in a larger grain size and a lower breakdown voltage. The addition of 1% copper seeds produces a breakdown voltage (V b) of ∼ 37 V and a leakage current (fic) of 29 μA. On the other hand, the addition of 1% cobalt seeds produced a breakdown voltage of 57 V and a leakage current of 70 μA. Both systems are of great technological interest for low voltage varistor applications, by means of appropriate strategies to reduce the leakage current. Using larger amounts of seeds was not effective since the values of breakdown voltage in both cases are close to a system without seeds. To our knowledge, there are no reports in the literature regarding the use of seeds in the SnO2 system for low voltage applications. A potential barrier model which illustrates the formation of oxygen species (O′2(ads), O′ads, and O″ads) at the expense of clusters near the interface between grains is proposed. © 2012 The American Ceramic Society.

Effect of Ag addition on phase transitions of the Cu-22.26 at.%Al-9.93 at.%Mn alloy

The phase transitions that occur in the Cu-22.26 at.%Al-9.93 at.%Mn and Cu-22.49 at.%Al-10.01 at.%Mn-1.53 at.%Ag alloys after slow cooling were studied using differential scanning calorimetry at different heating rates, microhardness changes with temperature, magnetization changes with temperature, scanning electron microscopy and energy dispersion X-ray spectroscopy. The results indicated that the presence of Ag does not modify the transition sequence of Cu-Al-Mn alloy, introduces a new transition due to the (Ag-Cu)-rich precipitates dissolution at about 800 K, and changes the mechanism of DO 3 phase dissolution. This mechanistic change was analyzed and a sequence of phase transitions was proposed for the reaction. © 2013 Elsevier B.V.

Determination of the Real Influence of the Addition of Four Thickening Agents in Creams Using Rheological Measurements

This study aimed to characterize different emulsions obtained by the addition of four thickening agents, using rheological measurements, beyond analyzing the emulsions by polarized light microscopy looking for liquid crystals on them. The addition of these four thickening agents did not modify the base emulsion rheology, only an improvement in the sensory of the formulation was verified. The polarized light microscopy showed the formation of liquid crystalline structures in all the formulations, thus, the thickening agents did not influence in this parameter too. However, the emulsions could be considered appropriated for cosmetic purposes, probably being highly physically stable. © 2013 Copyright Taylor and Francis Group, LLC.

A meta-analytical study about the relation of blood plasma addition in diets for piglets in the post-weaning and productive performance variables

The meta-analysis was used to evaluate the performance of piglets in post-weaning period, without imposition of sanitary challenge and fed diets containing blood plasma, obtained by spray-dried process (SDBP). Piglets are faced with normal challenges in post-weaning period such as environmental stress and the substitution of the liquid diet to a solid one. References regarding sanitary challenges were disregarded in this study. Only data regarding normal and expected challenges were considered. Data were obtained from indexed journals with information extracted from the material, methods and results sections of pre-selected scientific articles. First, the database was analyzed graphically to observe the distribution of data and presence of outliers. Afterwards correlation analysis and variance-covariance analyses were carried out. The database contained a total of 23 articles. The average initial weight of the piglets was 8.02. kg (4.00-9.28. kg) and the average initial age was 27 days (14-32 days). The average duration of feeding diets containing spray-dried blood plasma (SDBP) was 9 days (6-28 days). SDBP increased the feed conversion by 20.2% (P<0.05) during the initial period. Feed conversion during the total period was 10.2% higher (P<0.05) for animals fed with SDBP. Average daily weight gain and daily feed intake were not affected (P>0.05) during the entire period, but average daily gain was higher (P<0.05) for animals fed with SDBP during the initial period. The initial age of supplementation influenced the average daily weight gain and average daily feed intake of animals fed with SDBP. Better results were obtained than those obtained for animals up to 35 days of age fed diets without added SDBP supplementation. In early post-weaning period for piglets weaned up to 35 days of age, the SDBP supplementation positively influenced the average daily weight gain and feed conversion. © 2013 Elsevier B.V.

Mating in the pseudogamic apomictic Anemopaegma acutifolium DC: Another case of pseudo-self-compatibility in Bignoniaceae?

Self-compatibility in apomictic pseudogamic species is considered fundamental to assure reproduction by seeds in extreme situations, making apomictic species more advantageous than sexual ones in these scenarios. Anemopaegma acutifolium is a polyploidy, apomictic sporophytic species with no endosperm development in ovules of unpollinated pistils, which indicates obligate pseudogamy. Thus, the aim of the present work is to study the breeding system and post-pollination events to test if there is similar pseudogamous development irrespective of pollination treatment. We analysed fruit and seed set obtained in controlled experimental pollinations, as well as embryo number per seed, and the progress of ovule penetration, fertilisation and early endosperm development between self- and cross-pollinated pistils. We found that the species is self-fertile and that spontaneous selfing fruit set is also possible, although emasculated flowers never form fruits. Selfed pistils were as efficient as crossed ones for all parameters analysed, except for a delay in endosperm development observed in the former that may be an effect of the late-acting self-incompatibility. Therefore, the avoidance of selfed pistil abortion seems to be promoted by the presence of adventitious embryos and a normal endosperm. We conclude that A. acutifolium shows apomixis-related pseudo-self-compatibility, as in other self-fertile apomictic species of Bignoniaceae, which confer reproductive assurance and increases fruit-set and persistence ability in fast-changing tropical habitats. © 2012 German Botanical Society and The Royal Botanical Society of the Netherlands.

Ethanol addition as a strategy for start-up and acclimation of an AnSBBR for the treatment of landfill leachate

This study evaluated the ethanol addition as a strategy for start-up and acclimation of a pilot scale (1300 L) anaerobic sequencing batch biofilm reactor (AnSBBR) for the treatment of municipal landfill leachate with seasonal biodegradability variations. The treatment was carried out at ambient temperature (23.8 ± 2.1 °C) in the landfill area. In a first attempt, the leachate collected directly from landfill showed to be predominantly recalcitrant to anaerobic treatment and the acclimation was not possible. In a second attempt, adding ethanol to leachate, the reactor was successfully acclimated. After acclimation, without ethanol addition, the CODTotal influent ranged from 4970 to 13040 mg L-1 and the removal efficiencies ranged from 12.1% to 70.7%. A final test was carried out increasing the ammonia and free-ammonia concentration from 2486 mgN L-1 and 184 mgN L-1 to 4519 mgN L-1 and 634 mgN L-1, respectively, with no expressive inhibition verified. The start-up strategy was found to be feasible, providing the acclimation of the biomass in the AnSBBR, and maintaining the biomass active even when the leachate was recalcitrant. © 2013 Elsevier Ltd. All rights reserved.

Enhanced bulk and superficial hydrophobicities of starch-based bionanocomposites by addition of clay

In this work, thermoplastic starch (TPS)-clay bionanocomposites were obtained by an innovative methodology using a combination of methodologies commonly used in the composites and nanocomposites preparations. The main objectives or novelties were to confirm efficiency of the processing methodology by field emission gun scanning electron microscopy and investigate the effect of clay content on the spectroscopic, bulk and surface hydrophilic/hydrophobic properties of these bionanocomposites. Raman and FTIR spectroscopies confirmed the changes in the spectroscopic properties of the TPS bionanocomposites with the addition of the clay materials. Water absorption and contact angle measurements were also used to analyze the effect of the clay content on the hydrophilic properties of the TPS bionanocomposites. The results also showed that the addition of the cloisite-Na+ clay increased the bulk and surface hydrophobicities of the TPS matrix, which may increase its industrial application, particularly in manufacturing of food containers. © 2013 Elsevier B.V.

Evaluation of a potential hydroelectric project as an addition to an existing power system

Includes bibliography

Desempenho de escolares de 1ª a 4ª séries do ensino fundamental em Provas de Habilidades Metalingüísticas e de Leitura (PROHMELE)

Pós-graduação em Educação - FFC

Material compósito de matriz frágil reforçado com fibras naturais de sisal e malva: caracterização e correlações das propriedades e mecânicas

Este estudo propõe avaliar o comportamento mecânico dos compósitos de matriz cimentícia reforçados com fibras de sisal e malva. Correlacionar o comportamento dos materiais com variação do tipo e do comprimento das fibras. O material base utilizado na fabricação do compósito foi cimento, areia, água e fibra de sisal e malva. Usou-se u traço 1 : 2 : 0,5 (cimento, areia e água), com adição de 1% de fibras em relação ao peso da mistura. As fibras foram previamente cortadas no comprimento de 15 mm e 25 mm e adicionadas manualmente à mistura. As correlações dos compósitos foram obtidos através do ensaio de flexão em três pontos, seguindo norma RILEM 49. As características micro-estruturais foram avaliadas através do uso do microscópio eletrônico de varredura.Os resultados obtidos indicam que a inserção de fibras na matriz cimentícia diminui a força máxima aplicada no corpo de prova, porém houve um ganho na tenacidade e na pseudo ductilidade do material após o aparecimento da 1ª trinca. As fibras mais longas mostraram melhor desempenho com um pequeno destaque às fibras de MALVA.

Potenciais pseudo-newtonianos e a radiação escalar emitida por uma fonte girando ao redor de um objeto estelar

Neste trabalho usamos os potenciais pseudo-newtonianos propostos por Paczynski e Wiita, Nowak e Wagoner e Artemova et al. para calcular a radiação escalar emitida por uma fonte em movimento circular e uniforme ao redor de um objeto estelar. Comparamos os resultados obtidos nessa abordagem com os resultados encontrados via teoria quântica de campos no espaço-tempo de Schwarzschild. Obtemos que, do infinito até a órbita circular marginalmente estável (R = 6M) o potencial que melhor reproduz os resultados de Schwarzschild é o de Nowak e Wagoner. Já entre esta órbita e a última órbita circular instável (R = 3M) nenhum dos potenciais pseudo-newtonianos produz resultados satisfatórios, e o potencial newtoniano mostra-se como a melhor aproximação. O potencial de Paczynski e Wiita, o mais utilizado na literatura para analisar discos de acre ção, gerou os resultados menos satisfatórios em nossa análise.

Quebra dinâmica da simetria quiral na pseudo eletrodinâmica quântica em (2 + 1) dimensões

No presente trabalho, estudamos a quebra da simetria quiral na pseudo eletrodinâmica quântica em (2+1) dimensões usando o formalismo das equações de Schwinger-Dyson e investigamos as semelhanças deste modelo com a criticalidade encontrada na EDQ₃ e EDQ₄. Usando a aproximação “quenched-rainbow”, mostramos que existe um acoplamento crítico α_cc = π/16, acima do qual existe a geração de massa para os férmions e portanto, ocorrendo a quebra da simetria quiral. Também estudamos o caso com N campos fermiônicos usando a expansão 1/N na aproximação “unquenched-rainbow”, onde obtemos um número crítico N_c abaixo do qual a simetria quiral é quebrada e, para valores acima, a simetria é restaurada. No limite de acoplamento forte (g -- ∞), mostramos que este número crítico é o mesmo encontrado na EDQ₃ na expansão 1/N.

Modelagem de dados MT 2D em multicamadas com anisotropia arbitrária

Neste trabalho apresentamos a modelagem direta bidimensional do método Magnetotelúrico (MT) com anisotropia arbitrária na condutividade elétrica para modelos de multicamadas estratificadas horizontalmente, separando a resposta do campo resultante em duas partes, primária e secundária. A parte primária refere-se ao campo 1D do modelo na ausência de heterogeneidades; a secundária, à contribuição no campo resultante gerada pela anomalia. Esta modelagem foi feita via técnica numérica dos Elementos Finitos (EF). Apresentamos também a modelagem direta do caso MT 1D para o mesmo modelo e anisotropia arbitrária, porém, com solução analítica pelo método da matriz de propagação; tal resultado é usado como fonte na formulação 2D. No estudo a respeito do comportamento dos campos 1D em profundidade na presença da anisotropia, verificamos nas componentes horizontais que suas curvas dentro de cada camada se assemelham a de um campo na presença de fontes, pois experimentam um aumento na amplitude; além de verificar o surgimento da componente normal E_z do campo, sem que haja uma densidade de corrente nesta direção. Com arbitrariedade na anisotropia queremos dizer que seus eixos principais podem assumir qualquer orientação em relação ao eixo de referência adotado para o problema; tal orientação é descrita sob três rotações consecutivas, chamadas de strike, dip e slant, que simulam inclinações bastante presentes na geologia dos ambientes terrestres. Verificamos que a anisotropia provoca alterações no comportamento das pseudo-seções de resistividades aparentes, interferindo na interpretação correta dos dados.