Early detection of injuries in leaves of Clusia hilariana Schltdl. (Clusiaceae) caused by particulate deposition of iron

This study aims to evaluate the prognostic value of microscopic parameters of asymptomatic leaves of Clusia hilariana Schltdl. subjected to particulate deposition of iron (2.14 mg cm-2 day-1) for 45 consecutive days. Samples of young and expanded leaves without symptoms were collected and subjected to light and scanning electron microscopy techniques. The height of the epidermal cells on both surfaces of the leaf and the thickness of the hypodermis, the chlorophyll parenchyma, and the leaf blade were measured. Micromorphological injury occurred in the abaxial surface of young leaves and on both surfaces of expanded leaves. Erosion of the epicuticular wax and cuticle rupture were frequent on the adaxial surface, while on the abaxial surface of both leaves there was a loss of sinuosity on the anticlinal wall of the epidermal cells, stomatal deformity and obstruction. Micromorphometric alterations were seen in all leaf tissues except in the height of epidermic cells, probably due to the thick cuticle and prominent cuticular flanges. The highest difference in thickness of the leaf blade was seen in young leaves of plants subjected to SPMFe, indicating greater sensibility to particulate iron in comparison to the expanded leaves. The micromorphological and micromorphometric alterations in the leaf blade of Clusia hilariana Schltdl. showed the prognostic potential of these tools on the evaluation of impacts caused by the deposition of particulate matter, especially in the 'Restinga' natural vegetation, where the exposure is increasing due to the presence of iron ore industry in their surroundings.

Annual evolution of global, direct and diffuse radiation and fractions in tilted surfaces

It was evaluated the annual evolution of global, direct and diffuse components of incident solar radiation on tilted surfaces to 12.85, 22.85 and 32.85º, facing north, in Botucatu, state of São Paulo, Brazil. The radiometric fractions were obtained for each component of the radiation in the aforementioned surfaces, through the ratio with the global and top of the atmosphere radiations. Seasonality was evaluated based on monthly averages of daily values. The measures occurred between 04/1998 and 07/2001 at 22.85º; 08/2001 and 02/2003 at 12.85º; and from 03/2003 to 12/2007 at 32.85º, with concomitant measures in the horizontal surface (reference). The levels of global and direct radiation on tilted surfaces were lower in summer and higher in the equinoxes when compared with the horizontal. The diffuse radiation on tilted surfaces was lower in most months, with losses of up to 65%. A trend of increasing differences occurred between horizontal and tilted surfaces with the increase of the angle in all the components and fractions of incident radiation. The annual evolution of rainfall and cloud cover ratio directly affected the atmospheric transmissivity of direct and diffuse components in the region.

Outlining precision boundaries among areas with different variability standards using magnetic susceptibility and geomorphic surfaces

There is an increasing demand for detailed maps that represent in a simplified way the knowledge of the variability of a particular area or region maps. The objective was to outline precision boundaries among areas with different accuracy variability standards using magnetic susceptibility and geomorphic surfaces. The study was conducted in an area of 110 ha, which identified three compartment landscapes based on the geomorphic surfaces model. To determinate pH, organic matter, phosphorus, potassium and magnesium, the total sand and clay, 514 soil samples were collected at depths of 0-0.20 m and 0.60-0.80 m. The sum of base, cationic exchange capacity and base saturation were calculated and the magnetic susceptibility was evaluated in the laboratory using a system based on a balance of analytical precision method. Geomorphic surfaces identification allowed setting specific management areas (locations with maximum homogeneity of soil attributes). The map of spatial variability of magnetic susceptibility can be used to validate the precise boundaries among geomorphic surfaces identified in the field and infer the variability of clay content and soil base saturation.

Physical characteristics of oily spraying liquids and droplets formed on coffee leaves and glass surfaces

The physical characteristics of a spray liquid are important in getting a good droplet formation and control efficiency over a particular target. As a function of these characteristics, it is possible to decipher which is the best adjuvant based on the respective concentration used during the spray. Therefore, ten spraying liquids were prepared, which varied in concentrations of pesticide lufenuron + profenofos, mineral oil, water and manganese sulfate. Pendant droplets formed from these mixtures were measured to examine their impact on surface tension. Droplets were applied to the surface of coffee leaves and the surface tension, contact angle formed and the leaf area wetted by the droplet, were measured. A smooth glass surface was taken as a comparative to the coffee leaves. The highest concentrations of oil resulted in lower surface tension, smaller contact angles of droplets on leaf surfaces and larger areas wetted by the droplets. Both surfaces showed hydrophilic behavior.

Management of stab wounds to the anterior abdominal wall

The meeting of the Publication "Evidence Based Telemedicine - Trauma and Emergency Surgery" (TBE-CiTE), through literature review, selected three recent articles on the treatment of victims stab wounds to the abdominal wall. The first study looked at the role of computed tomography (CT) in the treatment of patients with stab wounds to the abdominal wall. The second examined the use of laparoscopy over serial physical examinations to evaluate patients in need of laparotomy. The third did a review of surgical exploration of the abdominal wound, use of diagnostic peritoneal lavage and CT for the early identification of significant lesions and the best time for intervention. There was consensus to laparotomy in the presence of hemodynamic instability or signs of peritonitis, or evisceration. The wound should be explored under local anesthesia and if there is no injury to the aponeurosis the patient can be discharged. In the presence of penetration into the abdominal cavity, serial abdominal examinations are safe without CT. Laparoscopy is well indicated when there is doubt about any intracavitary lesion, in centers experienced in this method.

Ureteral reconstruction with abdominal wall muscle flap: experimental study in rabbits

The authors detail the experimental development of a technique for the reconstruction of the ureter using a tubular shape, muscle flap of the abdominal wall. the preliminary results indicate the feasibility of this surgical technique.

Use of the amniotic membrane to cover the peritoneal cavity in the reconstruction of the abdominal wall with polypropylene mesh in rats

OBJECTIVE: to evaluate the efficacy of the amniotic membrane used with polypropylene mesh against the formation of adhesions and its influence on healing. METHODS: twenty five female Wistar rats were anesthetized for creating a parietal defect in the anterior abdominal wall. Its correction was made with polypropylene mesh alone and associated with amniotic membrane. In the control group (n=11), the screen was inserted alone. In group A (n=7) we interposed the amniotic membrane between the screen and the abdominal wall. In group B, the amniotic membrane was placed on the mesh, covering it. After seven days, the animals were euthanized for macroscopic and microscopic evaluation of healing. RESULTS: adhesions were observed in all animals except one in the control group. Severe inflammation was observed in all animals in groups A and B and in three of the control group, with significant difference between them (A and B with p=0.01). Pronounced angiogenic activity was noted in one animal in the control group, six in group A and four in group B, with a significant difference between the control group and group A (p=0.002) and group B (p=0.05). The scar collagen was predominantly mature, except in five animals of the control group, with significant difference between the control group and group A (p=0.05) and group B (p=0.05). CONCLUSION: The amniotic membrane did not alter the formation of adhesions in the first postoperative week. There were also pronounced inflammation, high angiogenic activity and predominance of mature collagen fibers, regardless of the anatomical plane that it was inserted in.

Use of surgical mesh of different compositions in the correction of the abdominal wall defect in rats

Objective: To analyze the performance of two surgical meshes of different compositions during the defect healing process of the abdominal wall of rats. Methods: thirty-three adult Wistar rats were anesthetized and subjected to removal of an area of 1.5 cm x 2 cm of the anterior abdominal wall, except for the skin; 17 animals had the defect corrected by edge-to-edge surgical suture of a mesh made of polypropylene + poliglecaprone (Group U - UltraproTM); 16 animals had the defect corrected with a surgical mesh made of polypropylene + polidioxanone + cellulose (Group P - ProceedTM). Each group was divided into two subgroups, according to the euthanasia moment (seven days or 28 days after the operation). Parameters analyzed were macroscopic (adherence), microscopic (quantification of mature and immature collagen) and tensiometric (maximum tension and maximum rupture strength). Results : there was an increase in collagen type I in the ProceedTM group from seven to 28 days, p = 0.047. Also, there was an increase in the rupture tension on both groups when comparing the two periods. There was a lower rupture tension and tissue deformity with ProceedTM mesh in seven days, becoming equal at day 28. Conclusion : the meshes retain similarities in the final result and more studies with larger numbers of animals must be carried for better assessment.

Plastic surgery in chest wall reconstruction: relevant aspects - case series

Objective: to discuss the participation of Plastic Surgery in the reconstruction of the chest wall, highlighting relevant aspects of interdisciplinaryness. Methods: we analyzed charts from 20 patients who underwent extensive resection of the thoracic integument, between 2000 and 2014, recording the indication of resection, the extent and depth of the raw areas, types of reconstructions performed and complications. Results: among the 20 patients, averaging 55 years old, five were males and 15 females. They resections were: one squamous cell carcinoma, two basal cell carcinomas, five chondrosarcomas and 12 breast tumors. The extent of the bloody areas ranged from 4x9 cm to 25x40 cm. In 12 patients the resection included the muscular plane. In the remaining eight, the tumor removal achieved a total wall thickness. For reconstruction we used: one muscular flap associated with skin grafting, nine flaps and ten regional fasciocutaneous flaps. Two patients undergoing reconstruction with fasciocutaneous flaps had partially suffering of the flap, solved with employment of a myocutaneous flap. The other patients displayed no complications with the techniques used, requiring only one surgery. Conclusion: the proper assessment of local tissues and flaps available for reconstruction, in addition to the successful integration of Plastic Surgery with the specialties involved in the treatment, enable extensive resections of the chest wall and reconstructions that provide patient recovery.

Effects of infection with Toxoplasma gondii oocysts on the intestinal wall and the myenteric plexus of chicken (Gallus gallus)

This paper aims to analyze the effects of the Toxoplasma gondii infection in the intestinal wall and myenteric plexus of chicken (Gallus gallus). Ten 36-day-old chickens were separated into two groups: control and experimental, orally inoculated with oocysts of the T. gondii strain M7741 genotype III. After 60 days the birds were submitted to euthanasia and had their duodenum removed. Part of the intestinal segments was submitted to histological routine, HE staining, PAS histochemical technique, and Alcian Blue. Qualitative analysis of the intestinal wall and comparative measurements among the groups with respect to total wall thickness, muscle tunic, mucosa, and tunica mucosa were carried out. Caliciform cells were quantified. The other part of the intestinal segments was fixed in formol acetic acid and dissected having the tunica mucosa and the tela submucosa removed. Neurons were stained with Giemsa, counted, and measured. Chickens from the experimental group presented diarrhea and inflammatory infiltrates in the tunica mucosa, thickness reduction of all the parameters assessed in the intestinal wall, and an increase of the number of caliciform cells. There was a ~70% reduction regarding the intensity of myenteric neurons; and the remaining cells presented a reduction of ~2.4% of the perikarion and ~40.5% of the nucleus (p<0.05). Chronic infection induced by T. gondii oocysts resulted in intestinal wall atrophy, mucin secretion increase, death and atrophy of chicken myenteric plexus neurons. Death and atrophy of myenteric plexus neurons may be related with the causes of diarrhea observed in chickens with toxoplasmosis.

Sawfly larval poisoning in cattle: Report on new outbreaks and brief review of the literature

Sawfly larval poisoning (SLP) is an acute hepatotoxicosis documented in livestock in Australia, Denmark and in countries of South America. It is caused by the ingestion of the larval stage of insects of the suborder Symphyta, order Hymenoptera, commonly known as "sawfly". Three species of sawfly are reportedly involved in the toxicosis. The insect involved in Australian SLP is Lophyrotoma interrupta (Pergidae), in Denmark the cause of SLP is the ingestion of the larvae Arge pullata (Argidae), and in South American countries documented outbreaks of SLP were caused by the ingestion of yet another sawfly, Perreyia flavipes (Pergidae). In all geographical areas where it occurred, SLP causes important livestock losses. In cattle, as well as in other affected species, the disease has a short clinical course and in many outbreaks affected cattle can be found dead. When observed, clinical signs include apathy, recumbence, tremors, paddling movements and death in 24-48 hours. Neurological signs such aggressiveness attributable to hepatic encephalopathy are also observed. In cases with a more protracted course icterus and photodermatitis may develop. Gross findings included ascites, petechiae and ecchymosis over serosal surfaces of thoracic and abdominal cavities, and an enlarged liver that displays accentuation of the lobular pattern and edema of the gall bladder wall. Sawfly larval body fragments and heads are consistently found in the fore stomachs and occasionally abomasum of affected cattle. Main microscopic lesions are restricted to the liver and consist of centrolobular (periacinar) to massive hepatocellular necrosis. In most lobules necrotic areas extended up to the portal triads where only a few viable hepatocytes remain. Mild to moderate lymphocyte necrosis is seen in lymphatic tissues. Cases occur in the winter months when the larval stages of the sawfly are developing. D-amino acid-containing peptides have been found to be the toxic principle in each sawfly involved in SLP. The octapeptide lophyrotomin is the major toxin in the in the larvae of Australian and Danish sawflies and is present in small amounts in the larvae of South American sawfly. The heptadecapeptide pergidin is the main toxin in the South American sawfly while small amounts of pergidin have been found in the other two species of toxic sawfly. During the winter of 2011 (July-August) four outbreaks of SLP were diagnosed in the State of Rio Grande do Sul, Brazil. The findings in those outbreaks are reported here and a brief review of the literature regarding SLP around the world is provided.

Research and development of III-V semiconductor surfaces for improved device interfaces

This thesis is devoted to understanding and improving technologically important III-V compound semiconductor (e.g. GaAs, InAs, and InSb) surfaces and interfaces for devices. The surfaces and interfaces of crystalline III-V materials have a crucial role in the operation of field-effect-transistors (FET) and highefficiency solar-cells, for instance. However, the surfaces are also the most defective part of the semiconductor material and it is essential to decrease the amount of harmful surface or interface defects for the next-generation III-V semiconductor device applications. Any improvement in the crystal ordering at the semiconductor surface reduces the amount of defects and increases the material homogeneity. This is becoming more and more important when the semiconductor device structures decrease to atomic-scale dimensions. Toward that target, the effects of different adsorbates (i.e., Sn, In, and O) on the III-V surface structures and properties have been investigated in this work. Furthermore, novel thin-films have been synthesized, which show beneficial properties regarding the passivation of the reactive III-V surfaces. The work comprises ultra-high-vacuum (UHV) environment for the controlled fabrication of atomically ordered III-V(100) surfaces. The surface sensitive experimental methods [low energy electron diffraction (LEED), scanning tunneling microscopy/spectroscopy (STM/STS), and synchrotron radiation photoelectron spectroscopy (SRPES)] and computational density-functionaltheory (DFT) calculations are utilized for elucidating the atomic and electronic properties of the crucial III-V surfaces. The basic research results are also transferred to actual device tests by fabricating metal-oxide-semiconductor capacitors and utilizing the interface sensitive measurement techniques [capacitance voltage (CV) profiling, and photoluminescence (PL) spectroscopy] for the characterization. This part of the thesis includes the instrumentation of home-made UHV-compatible atomic-layer-deposition (ALD) reactor for growing good quality insulator layers. The results of this thesis elucidate the atomic structures of technologically promising Sn- and In-stabilized III-V compound semiconductor surfaces. It is shown that the Sn adsorbate induces an atomic structure with (1×2)/(1×4) surface symmetry which is characterized by Sn-group III dimers. Furthermore, the stability of peculiar ζa structure is demonstrated for the GaAs(100)-In surface. The beneficial effects of these surface structures regarding the crucial III-V oxide interface are demonstrated. Namely, it is found that it is possible to passivate the III-V surface by a careful atomic-scale engineering of the III-V surface prior to the gate-dielectric deposition. The thin (1×2)/(1×4)-Sn layer is found to catalyze the removal of harmful amorphous III-V oxides. Also, novel crystalline III-V-oxide structures are synthesized and it is shown that these structures improve the device characteristics. The finding of crystalline oxide structures is exploited by solving the atomic structure of InSb(100)(1×2) and elucidating the electronic structure of oxidized InSb(100) for the first time.

Cytoskeletal proteins in the follicular wall of normal andcystic ovaries of sows

The expression of cytoskeletal proteins was evaluated immunohistochemically in 36 normal ovaries sampled from 18 sows and 44 cystic ovaries sampled from of 22 sows, was evaluated. All sows had history of reproductive problems, such as infertility or subfertility. The immunohistochemically stained area (IHCSA) was quantified through image analysis to evaluate the expression of these proteins in the follicular wall of secondary, tertiary, and cystic follicles. Cytokeratins (CK) immunoreactivity was strong in the granulosa cell layer (GC) and mild in the theca interna (TI) and externa (TE) of the normal follicles. There was severe reduction of the reaction to CK in the GC in the cystic follicles, mainly in the luteinized cysts. The immunoreactivity for vimentin was higher in the GC from normal and cystic follicles in contrast with the other follicular structures. In the luteinized cysts, the IHCSA for vimentin was significantly higher in TI and in both observed cysts, the labeling was more accentuated in TE. Immunohistochemical detection of desmin and α-SMA was restricted to the TE, without differences between the normal and cystic follicles. The results of the current study show that the development of ovarian cysts in sows is associated to changes in the expression of the cytoskeletal proteins CK and vimentin.

A law of the wall formulation for recirculating flows

This work presents a new law of the wall formulation for recirculating turbulent flows. An alternative expression for the internal length which can be applied in the separated region is also presented. The formulation is implemented in a numerical code which solves the k-epsilon model through a finite volume method. The theoretical results are compared with the experimental data of Vogel and Eaton (J. of Heat Transfer, Transactions of ASME, vol.107, pp. 922-929, 1985). The paper shows that the present formulation furnishes better results than the standard k-epsilon formulation.

An experimental/numerical study of the turbulent boundary layer development along a surface with a sudden change in roughness

A theory for the description of turbulent boundary layer flows over surfaces with a sudden change in roughness is considered. The theory resorts to the concept of displacement in origin to specify a wall function boundary condition for a kappa-epsilon model. An approximate algebraic expression for the displacement in origin is obtained from the experimental data by using the chart method of Perry and Joubert(J.F.M., vol. 17, pp. 193-122, 1963). This expression is subsequently included in the near wall logarithmic velocity profile, which is then adopted as a boundary condition for a kappa-epsilon modelling of the external flow. The results are compared with the lower atmospheric observations made by Bradley(Q. J. Roy. Meteo. Soc., vol. 94, pp. 361-379, 1968) as well as with velocity profiles extracted from a set of wind tunnel experiments carried out by Avelino et al.( 7th ENCIT, 1998). The measurements are found to be in good agreement with the theoretical computations. The skin-friction coefficient was calculated according to the chart method of Perry and Joubert(J.F.M., vol. 17, pp. 193-122, 1963) and to a balance of the integral momentum equation. In particular, the growth of the internal boundary layer thickness obtained from the numerical simulation is compared with predictions of the experimental data calculated by two methods, the "knee" point method and the "merge" point method.