Alkaline hydrothermal treatment of titanate nanostructures

Since its initial proposal in 1998, alkaline hydrothermal processing has rapidly become an established technology for the production of titanate nanostructures. This simple, highly reproducible process has gained a strong research following since its conception. However, complete understanding and elucidation of nanostructure phase and formation have not yet been achieved. Without fully understanding phase, formation, and other important competing effects of the synthesis parameters on the final structure, the maximum potential of these nanostructures cannot be obtained. Therefore this study examined the influence of synthesis parameters on the formation of titanate nanostructures produced by alkaline hydrothermal treatment. The parameters included alkaline concentration, hydrothermal temperature, the precursor material‘s crystallite size and also the phase of the titanium dioxide precursor (TiO2, or titania). The nanostructure‘s phase and morphology was analysed using X-ray diffraction (XRD), Raman spectroscopy and transmission electron microscopy. X-ray photoelectron spectroscopy (XPS), dynamic light scattering (non-invasive backscattering), nitrogen sorption, and Rietveld analysis were used to determine phase, for particle sizing, surface area determinations, and establishing phase concentrations, respectively. This project rigorously examined the effect of alkaline concentration and hydrothermal temperature on three commercially sourced and two self-prepared TiO2 powders. These precursors consisted of both pure- or mixed-phase anatase and rutile polymorphs, and were selected to cover a range of phase concentrations and crystallite sizes. Typically, these precursors were treated with 5–10 M sodium hydroxide (NaOH) solutions at temperatures between 100–220 °C. Both nanotube and nanoribbon morphologies could be produced depending on the combination of these hydrothermal conditions. Both titania and titanate phases are comprised of TiO6 units which are assembled in different combinations. The arrangement of these atoms affects the binding energy between the Ti–O bonds. Raman spectroscopy and XPS were therefore employed in a preliminary study of phase determination for these materials. The change in binding energy from a titania to a titanate binding energy was investigated in this study, and the transformation of titania precursor into nanotubes and titanate nanoribbons was directly observed by these methods. Evaluation of the Raman and XPS results indicated a strengthening in the binding energies of both the Ti (2p3/2) and O (1s) bands which correlated to an increase in strength and decrease in resolution of the characteristic nanotube doublet observed between 320 and 220 cm.1 in the Raman spectra of these products. The effect of phase and crystallite size on nanotube formation was examined over a series of temperatures (100.200 �‹C in 20 �‹C increments) at a set alkaline concentration (7.5 M NaOH). These parameters were investigated by employing both pure- and mixed- phase precursors of anatase and rutile. This study indicated that both the crystallite size and phase affect nanotube formation, with rutile requiring a greater driving force (essentially �\harsher. hydrothermal conditions) than anatase to form nanotubes, where larger crystallites forms of the precursor also appeared to impede nanotube formation slightly. These parameters were further examined in later studies. The influence of alkaline concentration and hydrothermal temperature were systematically examined for the transformation of Degussa P25 into nanotubes and nanoribbons, and exact conditions for nanostructure synthesis were determined. Correlation of these data sets resulted in the construction of a morphological phase diagram, which is an effective reference for nanostructure formation. This morphological phase diagram effectively provides a .recipe book�e for the formation of titanate nanostructures. Morphological phase diagrams were also constructed for larger, near phase-pure anatase and rutile precursors, to further investigate the influence of hydrothermal reaction parameters on the formation of titanate nanotubes and nanoribbons. The effects of alkaline concentration, hydrothermal temperature, crystallite phase and size are observed when the three morphological phase diagrams are compared. Through the analysis of these results it was determined that alkaline concentration and hydrothermal temperature affect nanotube and nanoribbon formation independently through a complex relationship, where nanotubes are primarily affected by temperature, whilst nanoribbons are strongly influenced by alkaline concentration. Crystallite size and phase also affected the nanostructure formation. Smaller precursor crystallites formed nanostructures at reduced hydrothermal temperature, and rutile displayed a slower rate of precursor consumption compared to anatase, with incomplete conversion observed for most hydrothermal conditions. The incomplete conversion of rutile into nanotubes was examined in detail in the final study. This study selectively examined the kinetics of precursor dissolution in order to understand why rutile incompletely converted. This was achieved by selecting a single hydrothermal condition (9 M NaOH, 160 °C) where nanotubes are known to form from both anatase and rutile, where the synthesis was quenched after 2, 4, 8, 16 and 32 hours. The influence of precursor phase on nanostructure formation was explicitly determined to be due to different dissolution kinetics; where anatase exhibited zero-order dissolution and rutile second-order. This difference in kinetic order cannot be simply explained by the variation in crystallite size, as the inherent surface areas of the two precursors were determined to have first-order relationships with time. Therefore, the crystallite size (and inherent surface area) does not affect the overall kinetic order of dissolution; rather, it determines the rate of reaction. Finally, nanostructure formation was found to be controlled by the availability of dissolved titanium (Ti4+) species in solution, which is mediated by the dissolution kinetics of the precursor.

Assessing cognitive development in early childhood : a comparison of the Bayley-III and the Stanford-Binet fifth edition

The Bayley Scales of Infant Development, Third Edition (Bayley-III) and Stanford-Binet Intelligence Scale, Fifth Edition (SB5) were administered in a sample of 26 typically developing children (12 males and 14 females) aged 24 – 42 months. Children completed the assessments in two separate sessions, counterbalanced for order of administration. Scores on the two instruments were not significantly related, with the exception of the SB5 Knowledge score, which was moderately correlated with the Language score on the Bayley-III (r = .41, p = 0.04). Despite no other significant correlations, for 22 of the 26 children, scores were very consistent across the two instruments. Implications for test selection are discussed.

Characterisation of public mobile data networks for aeronautical telemetry purposes

This paper describes the characterisation for airborne uses of the public mobile data communication systems known broadly as 3G. The motivation for this study was to explore how this mature public communication systems could be used for aviation purposes. An experimental system was fitted to a light aircraft to record communication latency, line speed, RF level, packet loss and cell tower identifier. Communications was established using internet protocols and connection was made to a local server. The aircraft was flown in both remote and populous areas at altitudes up to 8500ft in a region located in South East Queensland, Australia. Results show that the average airborne RF levels are better than those on the ground by 21% and in the order of -77 dbm. Latencies were in the order of 500 ms (1/2 the latency of Iridium), an average download speed of 0.48 Mb/s, average uplink speed of 0.85 Mb/s, a packet of information loss of 6.5%. The maximum communication range was also observed to be 70km from a single cell station. The paper also describes possible limitations and utility of using such a communications architecture for both manned and unmanned aircraft systems.

Role demands and work-family balance experience in Malaysia : the different moderating effects of collectivism and gender role identity among diverse ethnic groups

The purpose of this thesis is to examine the influence of ethnic cultural values on the relationship of role demands and the work-family balance (WFB) experience. Past studies have found that the demands from work and family roles have a different impact on the work-family experience in people of different ethnicity. Researchers attribute these results to the cultural differences across the groups. However, there has been no empirical support for these assumptions because most past studies did not explicitly measure the cultural dimension in their design. Therefore, although studies have found ethnic differences in work-family experience, as cultural variables were not measured, it cannot be determined whether these differences were due to the differing ethnic groups’ cultural styles. The present thesis is set up to address this limitation in the literature, employing the Malay and Chinese ethnic groups in Malaysia as the study samples. The investigation consisted of pilot interviews and two survey studies. The interviews were carried out to establish the perception of WFB by target participants of a non-western nation. The first survey served to identify whether the Malay and Chinese ethnic groups residing under the same economic and social systems vary in their perceptions of work and family roles. The second survey tests the research model empirically, that is, whether cultural values moderate the relationship between role demands and WFB and if these moderation effects vary across ethnic groups. From the interviews, the results indicated that work-family experience is not a universal experience, but is partly culture-specific. Specifically, in the case of Malaysia, WFB is very much observed from the role obligation perspective. In particular, balance is perceived when work duties and household affairs are both adequately fulfilled. On the other hand, the conceptualisation of WFB in terms of role satisfaction and role interference also emerged in the interviews, suggesting the universality of these constructs across cultures. The findings from Survey One indicated that participants of different ethnicities in this study do not differ greatly in their perceptions regarding their participation in work and family roles. Generally, these participants revealed the less traditional attitudes towards women’s participation in work and family roles. However, variations were observed between the two groups in terms of reasons for working, spouses’ preferences towards their employment, and the extent to which their work role is perceived to impede their normative role performance in the household. Despite these differences, the Malay and Chinese ethnic groups showed more similarities than differences in their perceptions of work and family. The findings from Survey Two, which tested the research model, produced mixed results. On the whole, the results showed that the cultural dimensions examined in this study (i.e. collectivism, work identity and family identity) did influence the relationship between role demands and WFB experience, thus providing empirical evidence for the assumption in the literature that the relationship between role demand and work-family experience is moderated by cultural values. Most importantly, support was found for the proposition that these moderation effects vary between the Malay and Chinese ethnic groups. Moreover, this study also found evidence that Malays and Chinese differ significantly on collectivism and work identity cultural dimensions where Malays are found to be more collectivist than the Chinese, while work identity is stronger in the Chinese than in the Malays. There is no difference in the levels of family identity between the two groups. Of all the three moderators, work identity was deemed the most important because many of the supported hypotheses pertained to the work identity moderating effects. In contrast, family identity does not seem to have much moderating influence on role demand-WFB relationships, while the results for the collectivism moderator are mixed. As such, although not conclusive, it can be deduced that variations in the effects of role demand on work-family experience across ethnicity are a result of the groups’ cultural differences, thereby supporting the assumption in the literature.

Online we are all able bodied : Online psychological sense of community and social support found through membership of disability-specific websites promotes well-being for people living with a physical disability

People with a physical disability are a population who for a number of reasons may be vulnerable to social isolation. Research into Internet-based support sites has found that social support and an online sense of community can be developed through computer mediated communication channels. This study aims to gain an understanding of the benefits that membership of disability-specific online communities may have for people with a physical disability. An online survey was administered to a sample of users of such sites (N = 160). Results indicated that users did receive moral support and personal advice through participating in such online communities. Further, results indicated that online social support and feeling a sense of community online were positively associated with participants' well-being in the areas of personal relations and personal growth.

A discussion of Fashion Victims: Various responses to the report by War on Want, Critical Perspectives on International Business, Vol. 3 Iss: 2, pp.170 - 185

Purpose – The purpose of this paper is to present a selection of responses to the report Fashion Victims, published by War on Want in December 2006. It offers a range of viewpoints presented by members of the Editorial Advisory Board of CPOIB. These are presented in chronological order of submission. There is some cross-reference by contributors to the work of others, but no attempt is made to present a unified argument. Design/methodology/approach – Presents the full contributions of involved participants, without mediation or editorial change. Findings – A number of different perspectives are presented on the central issue that is summarised by the opening heading in War on Want’s report – “How cheap is too cheap?” It is seen that the answer to this question is very much dependent upon the standpoint of the respondent. Originality/value – In presenting this form of commentary, members of the CPOIB Editorial Board seek to stimulate debate about an issue of concern to contemporary society, without resort to the time delay and mediating processes of peer-review normally attached to academic writing. It is hoped that this discussion will provoke further contributions and a widening of the debate. Keywords Corporate social responsibility, Multinational companies, Conditions of employment, Trade unions

Radiometric temperature analysis of the Hayabusa spacecraft re-entry

Hayabusa, an unmanned Japanese spacecraft, was launched to study and collect samples from the surface of the asteroid 25143 Itokawa. In June 2010, the Hayabusa spacecraft completed it’s seven year voyage. The spacecraft and the sample return capsule (SRC) re-entered the Earth’s atmosphere over the central Australian desert at speeds on the order of 12 km/s. This provided a rare opportunity to experimentally investigate the radiative heat transfer from the shock-compressed gases in front of the sample return capsule at true-flight conditions. This paper reports on the results of observations from a tracking camera situated on the ground about 100 km from where the capsule experienced peak heating during re-entry.

Measurement of total body water (TBW) and total energy expenditure (TEE) using stable isotopes

Understanding the relationship between diet, physical activity and health in humans requires accurate measurement of body composition and daily energy expenditure. Stable isotopes provide a means of measuring total body water and daily energy expenditure under free-living conditions. While the use of isotope ratio mass spectrometry (IRMS) for the analysis of 2H (Deuterium) and 18O (Oxygen-18) is well established in the field of human energy metabolism research, numerous questions remain regarding the factors which influence analytical and measurement error using this methodology. This thesis was comprised of four studies with the following emphases. The aim of Study 1 was to determine the analytical and measurement error of the IRMS with regard to sample handling under certain conditions. Study 2 involved the comparison of TEE (Total daily energy expenditure) using two commonly employed equations. Further, saliva and urine samples, collected at different times, were used to determine if clinically significant differences would occur. Study 3 was undertaken to determine the appropriate collection times for TBW estimates and derived body composition values. Finally, Study 4, a single case study to investigate if TEE measures are affected when the human condition changes due to altered exercise and water intake. The aim of Study 1 was to validate laboratory approaches to measure isotopic enrichment to ensure accurate (to international standards), precise (reproducibility of three replicate samples) and linear (isotope ratio was constant over the expected concentration range) results. This established the machine variability for the IRMS equipment in use at Queensland University for both TBW and TEE. Using either 0.4mL or 0.5mL sample volumes for both oxygen-18 and deuterium were statistically acceptable (p>0.05) and showed a within analytical variance of 5.8 Delta VSOW units for deuterium, 0.41 Delta VSOW units for oxygen-18. This variance was used as “within analytical noise” to determine sample deviations. It was also found that there was no influence of equilibration time on oxygen-18 or deuterium values when comparing the minimum (oxygen-18: 24hr; deuterium: 3 days) and maximum (oxygen-18: and deuterium: 14 days) equilibration times. With regard to preparation using the vacuum line, any order of preparation is suitable as the TEE values fall within 8% of each other regardless of preparation order. An 8% variation is acceptable for the TEE values due to biological and technical errors (Schoeller, 1988). However, for the automated line, deuterium must be assessed first followed by oxygen-18 as the automated machine line does not evacuate tubes but merely refills them with an injection of gas for a predetermined time. Any fractionation (which may occur for both isotopes), would cause a slight elevation in the values and hence a lower TEE. The purpose of the second and third study was to investigate the use of IRMS to measure the TEE and TBW of and to validate the current IRMS practices in use with regard to sample collection times of urine and saliva, the use of two TEE equations from different research centers and the body composition values derived from these TEE and TBW values. Following the collection of a fasting baseline urine and saliva sample, 10 people (8 women, 2 men) were dosed with a doubly labeled water does comprised of 1.25g 10% oxygen-18 and 0.1 g 100% deuterium/kg body weight. The samples were collected hourly for 12 hrs on the first day and then morning, midday, and evening samples were collected for the next 14 days. The samples were analyzed using an isotope ratio mass spectrometer. For the TBW, time to equilibration was determined using three commonly employed data analysis approaches. Isotopic equilibration was reached in 90% of the sample by hour 6, and in 100% of the sample by hour 7. With regard to the TBW estimations, the optimal time for urine collection was found to be between hours 4 and 10 as to where there was no significant difference between values. In contrast, statistically significant differences in TBW estimations were found between hours 1-3 and from 11-12 when compared with hours 4-10. Most of the individuals in this study were in equilibrium after 7 hours. The TEE equations of Prof Dale Scholler (Chicago, USA, IAEA) and Prof K.Westerterp were compared with that of Prof. Andrew Coward (Dunn Nutrition Centre). When comparing values derived from samples collected in the morning and evening there was no effect of time or equation on resulting TEE values. The fourth study was a pilot study (n=1) to test the variability in TEE as a result of manipulations in fluid consumption and level of physical activity; the magnitude of change which may be expected in a sedentary adult. Physical activity levels were manipulated by increasing the number of steps per day to mimic the increases that may result when a sedentary individual commences an activity program. The study was comprised of three sub-studies completed on the same individual over a period of 8 months. There were no significant changes in TBW across all studies, even though the elimination rates changed with the supplemented water intake and additional physical activity. The extra activity may not have sufficiently strenuous enough and the water intake high enough to cause a significant change in the TBW and hence the CO2 production and TEE values. The TEE values measured show good agreement based on the estimated values calculated on an RMR of 1455 kcal/day, a DIT of 10% of TEE and activity based on measured steps. The covariance values tracked when plotting the residuals were found to be representative of “well-behaved” data and are indicative of the analytical accuracy. The ratio and product plots were found to reflect the water turnover and CO2 production and thus could, with further investigation, be employed to identify the changes in physical activity.

A crystallographic snapshot of tyrosine trans-phosphorylation in action

Tyrosine trans-phosphorylation is a key event in receptor tyrosine kinase signaling, yet, the structural basis for this process has eluded definition. Here, we present the crystal structure of the FGF receptor 2 kinases caught in the act of trans-phosphorylation of Y769, the major C-terminal phosphorylation site. The structure reveals that enzyme- and substrate-acting kinases engage each other through elaborate and specific interactions not only in the immediate vicinity of Y769 and the enzyme active site, but also in regions that are as much of 18 A away from D626, the catalytic base in the enzyme active site. These interactions lead to an unprecedented level of specificity and precision during the trans-phosphorylation on Y769. Time-resolved mass spectrometry analysis supports the observed mechanism of trans-phosphorylation. Our data provide a molecular framework for understanding the mechanism of action of Kallmann syndrome mutations and the order of trans-phosphorylation reactions in FGFRs. We propose that the salient mechanistic features of Y769 trans-phosphorylation are applicable to trans-phosphorylation of the equivalent major phosphorylation sites in many other RTKs.

Interaction of contractile activity and training history on mRNA abundance in skeletal muscle from trained athletes

Skeletal muscle displays enormous plasticity to respond to contractile activity with muscle from strength- (ST) and endurance-trained (ET) athletes representing diverse states of the adaptation continuum. Training adaptation can be viewed as the accumulation of specific proteins. Hence, the altered gene expression that allows for changes in protein concentration is of major importance for any training adaptation. Accordingly, the aim of the present study was to quantify acute subcellular responses in muscle to habitual and unfamiliar exercise. After 24-h diet/exercise control, 13 male subjects (7 ST and 6 ET) performed a random order of either resistance (8 × 5 maximal leg extensions) or endurance exercise (1 h of cycling at 70% peak O2 uptake). Muscle biopsies were taken from vastus lateralis at rest and 3 h after exercise. Gene expression was analyzed using real-time PCR with changes normalized relative to preexercise values. After cycling exercise, peroxisome proliferator-activated receptor-γ coactivator-1α (ET ∼8.5-fold, ST ∼10-fold, P < 0.001), pyruvate dehydrogenase kinase-4 (PDK-4; ET ∼26-fold, ST ∼39-fold), vascular endothelial growth factor (VEGF; ET ∼4.5-fold, ST ∼4-fold), and muscle atrophy F-box protein (MAFbx) (ET ∼2-fold, ST ∼0.4-fold) mRNA increased in both groups, whereas MyoD (∼3-fold), myogenin (∼0.9-fold), and myostatin (∼2-fold) mRNA increased in ET but not in ST (P < 0.05). After resistance exercise PDK-4 (∼7-fold, P < 0.01) and MyoD (∼0.7-fold) increased, whereas MAFbx (∼0.7-fold) and myostatin (∼0.6-fold) decreased in ET but not in ST. We conclude that prior training history can modify the acute gene responses in skeletal muscle to subsequent exercise.

LMP estimation considering the uncertainty of wind power

One of the impediments to large-scale use of wind generation within power system is its variable and uncertain real-time availability. Due to the low marginal cost of wind power, its output will change the merit order of power markets and influence the Locational Marginal Price (LMP). For the large scale of wind power, LMP calculation can't ignore the essential variable and uncertain nature of wind power. This paper proposes an algorithm to estimate LMP. The estimation result of conventional Monte Carlo simulation is taken as benchmark to examine accuracy. Case study is conducted on a simplified SE Australian power system, and the simulation results show the feasibility of proposed method.

The development of a program to assist international nursing students to be prepared for clinical practice in the Australian health care context

Health education in Western Countries has grown considerably in the last decade and this has occurred for a number of reasons. Specifically Universities actively recruit International students as the health workforce becomes global; also it is much easier for students to move and study globally. Internationally there is a health workforce shortage and if students gain a degree in a reputable university their ability to work globally is improved significantly. However, when studying to practice in the health care field the student must undertake clinical practice in an acute or aged care setting. This can be a significant problem for students who are culturally and linguistically diverse in an English speaking country such as Australia. The issues that can arise stem from the language differences where communication, interpretation understanding and reading the cultural norms of the health care setting are major challenges for International students. To assist international students to be successful in their clinical education, an extra curriculum workshop program was developed to provide additional support. The program which runs twice each year includes on-campus interactive workshops that are complemented by targeted support provided for students and clinical staff who are supervising students’ practice experience in the workplace. As this is an English speaking country the workshop is based on practicing reading, writing, listening and speaking, as well as exploring basic health care concepts and cultural differences. This enables students to gain knowledge of and practice interpretation of cultural norms and expectations in a safe environment. This innovative series of interactive workshops in a highly student-centred learning environment combine education with role play and discussion with peers who are supported by culturally aware and competent Educators. Over the years it has been running, the program has been undertaken by an increasing number of students. In 2011, more than 100 students are expected to participate. Student evaluation of the program has confirmed that it has assisted the majority of them to be successful in their clinical studies. Effectiveness of the project is measured throughout the program and in follow up sessions. This ongoing information allows for continuous development of the program that serves to meet individual needs of the International student, the University and Service providers such as the hospitals. This feedback from students regarding their increased comprehension of the Australian colloquial Language, healthcare terminology, critical thinking and clinical skill development and a cultural awareness also enables them to maintain their feelings of self confidence and self esteem.

Turbulence characteristics of a small subtropical estuary during and after some moderate rainfall

In natural estuaries, scalar diffusion and dispersion are driven by turbulence. In the present study, detailed turbulence measurements were conducted in a small subtropical estuary with semi-diurnal tides under neap tide conditions. Three acoustic Doppler velocimeters were installed mid-estuary at fixed locations close together. The units were sampled simultaneously and continuously at relatively high frequency for 50 h. The results illustrated the influence of tidal forcing in the small estuary, although low frequency longitudinal velocity oscillations were observed and believed to be induced by external resonance. The boundary shear stress data implied that the turbulent shear in the lower flow region was one order of magnitude larger than the boundary shear itself. The observation differed from turbulence data in a laboratory channel, but a key feature of natural estuary flow was the significant three dimensional effects associated with strong secondary currents including transverse shear events. The velocity covariances and triple correlations, as well as the backscatter intensity and covariances, were calculated for the entire field study. The covariances of the longitudinal velocity component showed some tidal trend, while the covariances of the transverse horizontal velocity component exhibited trends that reflected changes in secondary current patterns between ebb and flood tides. The triple correlation data tended to show some differences between ebb and flood tides. The acoustic backscatter intensity data were characterised by large fluctuations during the entire study, with dimensionless fluctuation intensity I0b =Ib between 0.46 and 0.54. An unusual feature of the field study was some moderate rainfall prior to and during the first part of the sampling period. Visual observations showed some surface scars and marked channels, while some mini transient fronts were observed.

Why do nurses migrate? – a review of recent literature

Aim  To identify the reasons why nurses continue migrating across international borders. Background  International nurse recruitment and migration have been increasing in the last decade and recent trends show an increase in the movement of nurses between developing and developed countries, resulting in a worldwide shortage of nurses. Methods  A manual and electronic database literature search was conducted from January 2004 to May 2010. Qualitative content analysis was completed for the final 17 articles that satisfied the inclusion criteria. Results  Motivators to nurse migration were linked to financial, professional, political, social and personal factors. Although economic factors were the most commonly reported, they were not the only reason for migration. This was especially evident among nurses migrating between developed countries. Conclusion  Nurses migrate for a wide variety of reasons as they respond to push and pull factors. Implications for nursing management  It is important for nurse managers in the source countries to advocate incentives to retain nurses. In the recipient countries the number of international nurses continues to increase implying the need for more innovative ways to mentor and orientate these nurses.

A review of commuter exposure to ultrafine particles and its health effects

Ultrafine particles (UFPs, <100 nm) are produced in large quantities by vehicular combustion and are implicated in causing several adverse human health effects. Recent work has suggested that a large proportion of daily UFP exposure may occur during commuting. However, the determinants, variability and transport mode-dependence of such exposure are not well-understood. The aim of this review was to address these knowledge gaps by distilling the results of ‘in-transit’ UFP exposure studies performed to-date, including studies of health effects. We identified 47 exposure studies performed across 6 transport modes: automobile, bicycle, bus, ferry, rail and walking. These encompassed approximately 3000 individual trips where UFP concentrations were measured. After weighting mean UFP concentrations by the number of trips in which they were collected, we found overall mean UFP concentrations of 3.4, 4.2, 4.5, 4.7, 4.9 and 5.7 × 10^4 particles cm^-3 for the bicycle, bus, automobile, rail, walking and ferry modes, respectively. The mean concentration inside automobiles travelling through tunnels was 3.0 × 10^5 particles cm^-3. While the mean concentrations were indicative of general trends, we found that the determinants of exposure (meteorology, traffic parameters, route, fuel type, exhaust treatment technologies, cabin ventilation, filtration, deposition, UFP penetration) exhibited marked variability and mode-dependence, such that it is not necessarily appropriate to rank modes in order of exposure without detailed consideration of these factors. Ten in-transit health effects studies have been conducted and their results indicate that UFP exposure during commuting can elicit acute effects in both healthy and health-compromised individuals. We suggest that future work should focus on further defining the contribution of in-transit UFP exposure to total UFP exposure, exploring its specific health effects and investigating exposures in the developing world. Keywords: air pollution; transport modes; acute health effects; travel; public transport