Grain-size, carbona and calcium carbonate at DSDP Leg 58 Holes

Sand-silt-clay distribution was determined on 10-cm**3 sediment samples collected at the time the cores were split and described. The sediment classification used here is that of Shepard (1954), with the sand, silt, and clay boundaries based on the Wentworth (1922) scale. Thus the sand, silt, and clay fractions are composed of particles whose diameters are 2000 to 62.5 µm, 62.5 to 3.91 µm, and less than 3.91 µm, respectively. This classification is applied without regard to sediment type and origin; therefore, the sediment names used in this table may differ from those used elsewhere in this volume; e.g., a silt composed of nannofossils may be called a nannofossil ooze in a site chapter.

Organic carbon, age, lithology, and CPI-alkenes at DSDP Sites 57-440 and 56-436

"Bound" and "free" solvent-extractable lipids have been examined from Sections 440A-7-6, 440B-3-5, 440B-8-4, 440B-68-2, and 436-11-4. The compound classes studied include aliphatic and aromatic hydrocarbons, ketones, alcohols, and carboxylic acids. Carotenoids and humic acids have also been examined. The quantitative results are considered in terms of input indicators, diagenesis parameters, and structural classes. A difference in input is deduced across the Japan Trench, with a higher proportion of autochthonous components on the western inner trench slope compared with the more easterly, outer trench, wall and greater input in the early Pleistocene than in the Miocene. A variety of diagenetic transformations is observed at Site 440 as sample depth increases. Results are compared with those of samples from Atlantic Cretaceous sediments and from the Walvis Bay high productivity area.

Linear sedimentation rates and approximate mass accumulation rates at DSDP Site 61-462

A 560-meter-thick sequence of Cenomanian through Pleistocene sediments cored at DSDP Site 462 in the Nauru Basin overlies a 500-meter-thick complex unit of altered basalt flows, diabase sills, and thin intercalated volcaniclastic sediments. The Upper Cretaceous and Cenozoic sediments contain a high proportion of calcareous fossils, although the site has apparently been below the calcite compensation depth (CCD) from the late Mesozoic to the Pleistocene. This fact and the contemporaneous fluctuations of the calcite and opal accumulation rates suggest an irregular influx of displaced pelagic sediments from the shallow margins of the basin to its center, resulting in unusually high overall sedimentation rates for such a deep (5190 m) site. Shallow-water benthic fossils and planktonic foraminifers both occur as reworked materials, but usually are not found in the same intervals of the sediment section. We interpret this as recording separate erosional interludes in the shallow-water and intermediate-water regimes. Lower and upper Cenozoic hiatuses also are believed to have resulted from mid-water events. High accumulation rates of volcanogenic material during Santonian time suggest a corresponding significant volcanic episode. The coincidence of increased carbonate accumulation rates during the Campanian and displacement of shallow-water fossils during the late Campanian-early Maestrichtian with the volcanic event implies that this early event resulted in formation of the island chains around the Nauru Basin, which then served as platforms for initial carbonate deposition.

(Table 1) Physical properties of basalts from DSDP Legs 69 and 70

Physical properties of basalts from Deep Sea Drilling Project Sites 504 and 505, south of the Costa Rica Rift, including wet-bulk density, water content, sonic velocity, and thermal conductivity, were measured on board D/V Glomar Challenger during Legs 69 and 70. The mean wet-bulk density is 2.90±0.06 g/cm**3, porosity 5.0±2.2%, sonic velocity 5.75±0.30 km/s, and thermal conductivity 1.67±0.09 W/m°K. Basalts from this young ocean crust (5.9 m.y.) have relatively low porosity and consequently high density and sonic velocity, as compared to average DSDP basalts. Some systematic trends in depth variation of physical properties were found: down to Core 40 in Hole 504B, grain densities were lower than those deeper in the hole, whereas porosity in the upper section was higher. This can be attributed either to differences in the flow type or in the nature of alteration of basalts at the different levels in the hole.