Capillary thermal desorption unit for near real-time analysis of VOCs at sub-trace levels. Application to the analysis of environmental air contamination and breath samples

A capillary microtrap thermal desorption module is developed for near real-time analysis of volatile organic compounds (VOCs) at sub-ppbv levels in air samples. The device allows the direct injection of the thermally desorbed VOCs into a chromatographic column. It does not use a second cryotrap to focalize the adsorbed compounds before entering the separation column so reducing the formation of artifacts. The connection of the microtrap to a GC–MS allows the quantitative determination of VOCs in less than 40 min with detection limits of between 5 and 10 pptv (25 °C and 760 mmHg), which correspond to 19–43 ng m−3, using sampling volumes of 775 cm3. The microtrap is applied to the analysis of environmental air contamination in different laboratories of our faculty. The results obtained indicate that most volatile compounds are easily diffused through the air and that they also may contaminate the surrounding areas when the habitual safety precautions (e.g., working under fume hoods) are used during the manipulation of solvents. The application of the microtrap to the analysis of VOCs in breath samples suggest that 2,5-dimethylfuran may be a strong indicator of a person's smoking status

Fenóis halogenados e/ou sulfatados de macroalgas marinhas

During the biological evolution, marine macroalgae have developed biochemicals tools in order to utilize components of seawater such as sulfates and halogens, to produce a variety of chemicals (secondary metabolites).This review shows and discuss the occurrence of sulfated and/or halogenated phenolic compounds in seaweeds.

Caracterização de quitosana por Cromatografia de Permeação em Gel - Influência do método de preparação e do solvente

In this work, samples of chitosan obtained in different conditions were characterized by molecular weight distribution, using Gel Permeation Chromatography (GPC), in two different solvents. It was observed that the increase in the number of deacetylation steps promotes a increase in the degree of deacetylation followed by a decrease in the average of molecular weight and polydispersion. The GPC curves obtained for chitosan samples in the two solvents used (CH3COOH 0.30 mol/dm³ - CH3CONa 0.20 mol/dm³ and CH3COOH 0.10 mol/dm³ - NaCl 0.20 mol/dm³) showed small difference in elution volume, but significant changes in the average molecular weight (Mn and Mw) and polydispersion that, in agree with the values of Huggins constant, present evidences of chitosan aggregates formation in the second solvent.

Fragmentação de moléculas pela luz síncrotron e por elétrons rápidos. I. O caso do halotano, C2F3HClBr

The photofragmentation of a core-excited halogenated compound, Halotane (C2F3HClBr), generally used as anesthetic by inhalation, has been studied using high energy photons and electrons near C 1s ionization edge (~ 300 eV), using time-of-flight mass spectrometry in multicoincidence mode. We observe strong differences between the molecular fragmentation induced by photons and electron impact.

Aquecimento em forno de microondas / desenvolvimento de alguns conceitos fundamentais

The microwave oven became a common domestic equipment, due mainly to the short time spent to heat foods. One of the most interesting characteristics of the microwave oven is the selective heating. Different from the conventional oven, where the heating is not selective, the heating by microwave depends on the chemical nature of the matter. Many Students of Chemistry have no knowledge of the principles involved in this selective heating, in spite of the daily microwave oven use. The heating by microwave is feasible for chemistry courses. In discussions about the microwave absorption by the matter it is possible to explore chemical properties like: heat capacity, chemical bound, molecular structure, dipole moments, polarization and dielectric constant. This paper presents the basic principles involved in the microwave heating. It is proposed a simple and inexpensive experiment that could be developed in general chemistry courses, to illustrate the relationship between heating and the chemical properties of some solvents. Experiments to check the power of the microwave oven are also proposed.

Descomposicion termica del diperoxido de pinacolona (3,6-diterbutil-3,6-dimetil-1,2,4,5-tetraoxaciclohexano) en solución de 2-metoxietanol

The thermal decomposition reaction of pinacolone diperoxide (DPP; 0.02 mol kg-1) in 2-methoxyethanol solution studied in the temperature range of 110.0-150.0 °C, follows a first-order kinetic law up to at least 50% DPP conversion. The organic products observed were pinacolone, methane and tert-butane. A stepwise mechanism of decomposition was proposed where the first step is the homolytic unimolecular rupture of the O-O bond. The activation enthalpy and activation entropy for DPP in 2-methoxyethanol were calculated (deltaH# = 43.8 ± 1.0 kcal mol-1 and deltaS# = 31.9 ± 2.6 cal mol-1K-1) and compared with those obtained in other solvents to evaluate the solvent effect.

Xerogel p-anisidinapropilsílica: estudo da estabilidade térmica e da resistência à lixiviação com solventes

The xerogel p-anisidinepropylsilica was obtained. This solid presents some residual paraffin and also a small fraction of high organofunctionalized material that was leached in polar solvent. The xerogel purification could be achieved by exhaustively washing with hexane and dichloromethane solvents, or submitting the xerogel to thermal treatment up to 300 ºC, in vacuum. The resulting purified xerogel material present an appreciable thermal stability and resistance to leaching by solvents.

Fractionation of Wood Extracts

The aim of this thesis was to fractionate wood extracts into pure fractions using membrane technology, to observe membrane behaviour in solvents and to study the effect of conditioning on membrane performance. Four different wood extracts were used in the performed filtrations. In the literature part, the focus was on the effect of different solvent properties on polymeric membranes, especially on their retention and flux. Solute properties, such as shape, polarity and charge, were examined. Transport models, membrane stability and ways to improve the stability, when solvents were filtered, were also discussed. The experimental part consisted of a series of filtrations, where the effect of the wood extracts and solvent concentration on solute retention was observed. Polymeric and ceramic membranes were tested under different conditions and the solute analyses were performed with GC and GC-MS. It was discovered that it is possible to fractionate wood extracts using membrane technology to some extent, but more research must be done to understand the mechanisms behind the various interactions between the solvent and the membrane. Conditioning was also considered as an important part of the membrane pre-treatment.

Transferência de energia entre corantes catiônicos em sistemas homogêneos

In this work, the energy transfer by dipole-dipole interaction between cationic dyes in n-alcohols (methanol, ethanol, 1-propanol and 1-butanol) is studied by time resolved and steady state fluorescence measurements. The critical radii of energy transfer were determined by three independent methods; the spectral overlap, fluorescence decay profiles, and relative intensity measurements. In all solvents, R0 values of the dye pairs obtained from spectral overlap were between 40 to 90 Å. Steady state and time resolved fluorescence measurements resulted in values of R0 in the range of 50 - 80 Å, with good correlation of values.

Gerenciamento de resíduos químicos e águas servidas no laboratório de isótopos estáveis do CENA/USP

A system for disposal and recovery of the main effluents and chemical waist from isotope separation plants and enriched compounds-15N and 34S production has been carried out at the Stable Isotope Laboratory (LIE) of the CENA/USP. Around four hundred thousand liters of effluents has been recovered yearly. Among the recovered chemical wastes, the more relevant are: ammonia; brome; ammonium and sodium sulfate; sodium hydroxide; sulfur dioxide; and hydrochloric acid. Chemical wastes containg recoverable heavy metals (Ag, Cr and Cu) and solvents (methanol, ethanol and acetone) are processed and recovered. Gaseous emissions, mainly H2S are used for recovery of heavy metals solutions. The minimization of the residues waters, as well the reduction of electric energy consume was established using a water deionization system. A cost/effect balance of the process is reported.

Determinação de tanino em pedúnculo de caju: método da vanilina versus método do butanol ácido

To improve tannin assay in cashew apple, several parameters were examined, including (1) extraction solvents, (2) effects of water and boiling time on butanol acid reaction and (3) correlation between vanillin and butanol acid assay of tannin in cashew apples. The 50-70% acetone extracted the greatest amount of tannin from cashew apples. Concentrations of water in butanol reagents were adjusted and boiling time of butanol reaction was reduced at 15 min. Tannin of unripe cashew apples was purified on Sephadex LH-20, aiming to obtain tannin standard for butanol assay. The vanillin assay presented high correlation with the butanol acid assay.

Efecto de solvente sobre la descomposición térmica de trans-3,6-dimetil-3,6-difenil-1,2,4,5-tetraoxaciclohexano en solución

The thermal decomposition reaction of trans-3,6-dimethyl-3,6-diphenyl-1,2,4,5-tetraoxacyclohexane (acetophenone cyclic diperoxide, DPAF), in different solvents (methanol, 1,4-dioxane, acetonitrile and 2-propanol/benzene mixtures) in the initial concentration and temperature ranges of (4.2-10.5) x 10-3 M and 140.0 to 185.0 ºC, respectively, follows a pseudo first order kinetic law up to at least 70% DPAF conversion. An important solvent effect on the rate constant values, activation parameters (DH# and DS#) and reaction products obtained in different solvents is detected, showing that the reaction is accelerated in alcohols.

Intercalação e funcionalização da brucita com ácidos carboxílicos

Brucite (Mg(OH)2) is a structural model of several natural layered minerals as well as of synthetic layered double hydroxides (LDH). Exchange reaction studies of these compounds are well documented in the literature but surface chemical modifications, especially for brucite, are quite rare. We report the behaviour of brucite in reaction with succinic and benzoic acid in different solvents and temperatures. The compounds were analysed through X-ray diffraction (XRD) and infrared spectroscopy (FTIR). The surfaces of brucite crystals were grafted producing expansions, attributed to the arrangement of the grafted species between the layers.

Análise sistemática de reagentes e resíduos sem identificação

This work presents a detailed routine applied to the identification of unknown chemicals and wastes. 786 specimens were analyzed during 20 months. Unknown materials fell into three basic classes: (i) commercial chemicals without labels or illegible ones; (ii) laboratory synthesis products; (iii) used solvents (including mixtures). Uranium and thorium were recovered form their wastes. Unknown chemicals were mainly inorganic compounds, many of which had never been opened. Alkaline salts were dominant, but also precious metal compounds were identified. Laboratory synthesis products were organic compounds. The final destination depended on the nature of the chemical. Most organic compounds were sent to incineration; inorganic salts were distributed among several public organizations, including secondary and technical schools. The work described in this paper greatly reduced the amount of wastes that had to be sent to disposal.

Óxido misto de ítrio-alumínio dopado com Eu(III)

In this work, we report the synthesis and the photoluminescence features of Eu(III)-doped yttrium-aluminium oxide obtained by non-hydrolytic sol-gel routes. After heating the powders above 600 ºC the XRD patterns show the presence of the Y4Al2O9 (YAM) and Y3Al5O12 (YAG) phases. At 800 and at 1500 ºC the PL spectra display the Eu(III) lines characteristic of the YAM monoclinic phase. The 5D0->7F2 transition is favored relatively to the 5D0->7F1 lines. However, at 1100 ºC the cubic YAG is the preferential phase and the 5D0->7F1 transition dominates the spectrum. The Eu(III) ions lie in a centrosymmetrical site. The different solvents used in the sol-gel synthesis also change the relative proportion between these two phases. This is monitored analyzing the modifications in the relative intensity between the 5D0->7F2 and the 5D0->7F1 transitions.