895 resultados para Field-in-field
Resumo:
Centrifugal compressors are widely used for example in process industry, oil and gas industry, in small gas turbines and turbochargers. In order to achieve lower consumption of energy and operation costs the efficiency of the compressor needs to be improve. In the present work different pinches and low solidity vaned diffusers were utilized in order to improve the efficiency of a medium size centrifugal compressor. In this study, pinch means the decrement of the diffuser flow passage height. First different geometries were analyzed using computational fluid dynamics. The flow solver Finflo was used to solve the flow field. Finflo is a Navier-Stokes solver. The solver is capable to solve compressible, incompressible, steady and unsteady flow fields. Chien's k-e turbulence model was used. One of the numerically investigated pinched diffuser and one low solidity vaned diffuser were studied experimentally. The overall performance of the compressor and the static pressure distribution before and after the diffuser were measured. The flow entering and leaving the diffuser was measured using a three-hole Cobra-probe and Kiel-probes. The pinch and the low solidity vaned diffuser increased the efficiency of the compressor. Highest isentropic efficiency increment obtained was 3\% of the design isentropic efficiency of the original geometry. It was noticed in the numerical results that the pinch made to the hub and the shroud wall was most beneficial to the operation of the compressor. Also the pinch made to the hub was better than the pinchmade to the shroud. The pinch did not affect the operation range of the compressor, but the low solidity vaned diffuser slightly decreased the operation range.The unsteady phenomena in the vaneless diffuser were studied experimentally andnumerically. The unsteady static pressure was measured at the diffuser inlet and outlet, and time-accurate numerical simulation was conducted. The unsteady static pressure showed that most of the pressure variations lay at the passing frequency of every second blade. The pressure variations did not vanish in the diffuser and were visible at the diffuser outlet. However, the amplitude of the pressure variations decreased in the diffuser. The time-accurate calculations showed quite a good agreement with the measured data. Agreement was very good at the design operation point, even though the computational grid was not dense enough inthe volute and in the exit cone. The time-accurate calculation over-predicted the amplitude of the pressure variations at high flow.
Resumo:
The objective of this work was to evaluate the contribution of efficient nitrogen-fixing rhizobial strains to grain yield of new cowpea cultivars, indicated for cultivation in the Brazilian Semiarid region, in the sub-medium of the São Francisco River Valley. Two experiments were set up at the irrigated perimeters of Mandacaru (Juazeiro, state of Bahia) and Bebedouro (Petrolina, state of Pernambuco). The treatments consisted of single inoculation of five rhizobial strains - BR 3267, BR 3262, INPA 03-11B, UFLA 03-84 (Bradyrhizobiumsp.), and BR 3299T(Microvirga vignae) -, besides a treatment with nitrogen and a control without inoculation or N application. The following cowpea cultivars were evaluated: BRS Pujante, BRS Tapaihum, BRS Carijó, and BRS Acauã. A randomized complete block design, with four replicates, was used. Inoculated plants showed similar grain yield to the one observed with plants fertilized with 80 kg ha-1 N. The cultivars BRS Tapaihum and BRS Pujante stood out in grain yield and protein contents when inoculated, showing their potential for cultivation in the sub-medium of the São Francisco River Valley.
Resumo:
Russian corrugated board market is rapidly developing. Owing to that Russia becomes more and more attractive to the companies ¿ world leaders in corrugated board production. Thus, in order to strengthen or even to maintain its market position the firm should uninterruptedly develop improving volume and quality of the products. At the same time operations in the Russian market are commonlyassociated with various types of risks which should be avoided. Unfortunately, the information of the Russian corrugated board market is not systematized yet there is almost no theoretical background in this areaand, therefore, the thesis is mainly based on the practical experience of the managers of Stora Enso. The goal of the paper is to define and describe the main particularities of Russian corrugated board market which are lying in different areas and to concentrate on the difficultieswith which a corrugated board factory may face while functioning in the Russian market. The contribution of the thesis consists of forming general requirements and principles while establishing a corrugated boardproduction facility and maintaining its operations in order to avoid risks, to save time and financial resources and as a result to operate in the Russian market obtaining higher profits.
Resumo:
Abstract: The objective of this work was to evaluate Trichoderma harzianum isolates for biological control of white mold in common bean (Phaseolus vulgaris). Five isolates were evaluated for biocontrol of white mold in 'Perola' common bean under field conditions, in the 2009 and 2010 crop seasons. A commercial isolate (1306) and a control treatment were included. Foliar applications at 2x109 conidia mL-1 were performed at 42 and 52 days after sowing (DAS), in 2009, and at 52 DAS in 2010. The CEN287, CEN316, and 1306 isolates decreased the number of Sclerotinia sclerotiorum apothecia per square meter in comparison to the control, in both crop seasons. CEN287, CEN316, and 1306 decreased white mold severity during the experimental period, when compared to the control.
Resumo:
Tässä työssä on esitetty väsyttävän kuormituksen mittaamiseen ja mittausdatan jälkikäsittelyyn sekä väsymismitoitukseen liittyviä menetelmiä. Menetelmien sovelluskohteena oli metsäkoneen kuormain, joka on väsyttävästi kuormitettu hitsattu rakenne. Teoriaosassa on kuvattu väsymisilmiötä ja väsymismitoitusmenetelmiä sekä kuormitusten tunnistamiseen ja mittausten jälkikäsittelyyn liittyviä menetelmiä. Yleisimmin käytettyjen väsymismitoitusmenetelmien rinnalle on esitetty luotettavuuteen perustuvaa väsymismitoitusmenetelmää. Kuormainten suunnittelussa on keveys- j a kestoikävaatimusten takia erityisen suuri merkitys väsymisen huomioimisella. Rakenteille on ominaista tietyt toiminnan kannalta välttämättömät hitsatut yksityiskohdat, jotka usein määräävät koko rakenteen kestoiän. Koska nämä ongelmakohdat pystytään useimmiten tunnistamaan jo suunnitteluvaiheessa, voidaan yksityiskohtien muotoilulla usein parantaa huomattavasti koko rakenteen kestoikää. Näiden yksityiskohtien optimointi on osittain mahdollista toteuttaa ilman kuormituskertymätietoa, mutta useimmiten kuormitusten tunnistaminen on edellytys parhaan ratkaisun löytymiselle. Tällöin toistaiseksi paras keino todellisen väsyttävän kuormituksen tunnistamiseksi on pitkäaikaiset kenttämittaukset. Kenttämittauksilla selvitetään rakenteeseen kohdistuvat kuormitukset venymäliuskojen avulla. Kuormitusten tunnistamisella on erityisen suuri merkitys kun halutaan määrittää rakenteen kestoikä. Väsyminen ja väsyttävä kuormitus ovat kuitenkin tilastollisia muuttujia j a yksittäiselle rakenteelle ei ole mahdollista määrittää tarkkaa k estoikää. Tilastollisia menetelmiä käyttäen on kuitenkin mahdollista määrittää rakenteen vaurioitumisriski. Laskettaessa vaurioitumisriskiä suurelle määrälle yksittäisiä rakenteita voidaan muodostaa tarkkojakin ennusteita mahdollisten vaurioiden lukumäärästä. Tällöin kuormituskertymätiedosta voi olla tavanomaisen suunnittelun lisäksi laajempaa hyötyä esimerkiksi takuukäsittelyssä. Tässä työssä on sovellettu esitettyjä teorioita käytännössä metsäkoneen harvesterin puomiston väsymistarkasteluun. Kyseisen rakenteen kuormituksia mitattiin kahden viikon aikana yhteensä 35 tuntia, jonka perusteella laskettiin väsyttävän kuormituksen tilastollinen jakauma esimerkkitapaukselle. Mittauksen perusteella ei voitu tehdä kuitenkaan johtopäätöksiä tuotteen koko elinkaaren kuormituksista eikä muiden samanlaisten tuotteiden kuormituksista, koska mitattu otos oli suhteellisen lyhyt ja rajoittui vain yhteen käyttäjään ja muutamaan käyttökohteeseen. Menetelmien testaamiseksi kyseinen otos oli kuitenkin riittävä. Kuormituskertymätietoa käytettiin hyväksi myös laatumääritysten muodostamisessaesimerkkitapaukselle. Murtumismekaniikkaan perustuvalla menetelmällä arvioitiinharvesteripilarin valun mahdollisten valuvirheiden suurin sallittu koko. Luotettavuuteen pohjautuvan mitoitusmenettelyn tarve näyttää olevanlisääntymässä, joten pitkäaikaisten kenttämittausten tehokas hyödyntäminen tulee olemaan keskeinen osa väsymismitoitusta lähitulevaisuudessa. Menetelmiä olisi mahdollista tehostaa yhdistämällä kuormituskertymään erilaisia kuormitusten suhteen riippuvia tunnettuja suureita kuten käsiteltävän puun halkaisija. Todellisettuotekohtaiset tilastolliset jakaumat kuormituksista voitaisiin muodostaa mahdollisesti tehokkaammin, jos esimerkiksi kuormitusten riippuvuus metsätyypistä pystyttäisiin ensin määrittämään.
Resumo:
This paper presents the first results of a current research project about human – environmental interactions in the Montseny Massif. Our work sets out to integrate two research lines in the studied area: - Archaeological and archaeo-morphological surveys in a lower part of the mountains in order to characterize the evolution of the settlements and field systems. - The geological and geomorphological characterization of the slope and terrace deposits in relation with field systems and archaeological data. First results point out the intensive occupation of these inland areas during the Iberian and the Roman periods. Post-Roman sediments show different processes of erosion.
Resumo:
Field poppy, Papaver rhoeas L., is a very common weed in winter cereals in North-Eastern Spain. Its control is becoming difficult due to expanding herbicide resistance. To control field poppies there are alternative strategies such as non-chemical control that take into account the weed emergence period. However, there is a lack of knowledge of P. rhoeas emergence patterns in semi-arid conditions. Thus, here we conducted pot experiments on the emergence of P. rhoeas. We aimed to describe the emergence period and to quantify the emergence of a susceptible and of a herbicide-resistant P. rhoeas population at two locations in Catalonia, Spain, from 1998 to 2001 and until 2004 at one of them. Therefore, pots containing seeds of both populations were established at the two locations and emergence was recorded monthly. We studied the origin of the population, the sowing location, the effect of cultivation and the sowing year. First, we found that the main emergence peaks in our experiments occurred in autumn, accounting for between 65.7 and 98.5% of the annual emergence from October to December, and only little emergence was recorded in spring. This emergence pattern is different from those found in the literature corresponding to Northern European countries, where in some cases main flushes occur only in autumn, in spring and winter or only in spring. The emergence was mainly affected by cultivation, but the effect of light stimulus was observed several months later. As a consequence, cultivation should be done in early autumn, promoting emergence during the whole autumn and winter so that emerged seedlings can be controlled before sowing a spring crop. Second, most experiments showed that the emergence was significantly higher in the first autumn than in the following seasons, e.g. 4.1% emergence in the first year and only 2.1, 2.3, 0.5 and 0.6% new emergence at one of the locations for the second, third, fourth and fifth years. Thus, after having a severe P. rhoeas infestation causing a big seed rain, emergence should be stimulated by autumn cultivation in the following season and seedlings controlled by trying to deplete the soil seed bank as much as possible. Despite the fact that emergence will be staggered throughout several years and that there was a significant relationship between rainfall and emergence, so that dry years will cause a smaller emergence rate of the weed, these findings define a cultural management strategy to reduce P. rhoeas infestations and to contribute to integrated weed management strategies combining it with other tools.
Resumo:
In previous studies, we demonstrated cross-antagonism in pheromone perception between pheromone componentsof the two corn (Zea mays L.) borers Sesamia nonagrioides Lefèbvre (Lepidoptera: Noctuidae) and Ostrinia nubilalis (Hübner) (Lepidoptera: Crambidae) in the laboratory and in the field. The two pheromone components identified as responsible for this cross-antagonism were Z 11-16:Ald, a minor component of S. nonagrioides pheromone, and Z 11-14:Ac, the main component of the pheromone of the Z-strain of O. nubilalis, which inhibited the response of O. nubilalis and S. nonagrioides, respectively. Here, we study this antagonism phenomenon in the field by air permeation of maize plots with each of the two components separately and measurement of mating in caged couples of the two corn borers on treated and untreated plots during three years. A significant reduction in mating rates was observed on the permeated plots: 7% for S. nonagrioides and 12% for O. nubilalis. When dispenser charges (200 ng) were increased by 50% and 75% in the third year, no decrease in mating rates was recorded at either of the increased concentrations. On the other hand, the use of large cages resulted in an increase of 8% to 12% in the percentage of unmated females in each of the two corn borers suggesting that at more realistic field corn borer densities, 0,1 couples/plant instead of the 2 couples/plant used in this experiment, cross-antagonism in the two corn borers could be higher than that recorded in small cages.
Resumo:
General Packet Radio Service (GPRS) mahdollistaa pakettimuotoisen tiedonsiirron GSM-verkossa. Se tarjoaa yhteyden pakettidataverkkoihin, nostaen samalla tiedonsiirtonopeutta radiorajapinnassa. Radioresurssit ovat varattuna vain silloin kun on jotain lähetettävää, tehden täten radioresurssien käytön paljon tehokkaammaksi. Tämä diplomityö keskittyy GPRS protokollaan ja erityisesti sen datapinossa olevaan Radio Link Control (RLC) kerrokseen. RLC-kerros huolehtii GPRS- puhelimen ja tukiaseman välisen yhteyden luotettavuudesta. Työn tavoitteena on tutkia RLC-kerroksen toiminnallisuutta ja sen luotettavuutta heikossa kentässä, sekä selvittää heikon kentän vaikutusta uudelleenlähetyksiin. Työn tuloksena saadaan arvio signaalin voimakkuuden sekä uudelleen lähetysten vaikutuksesta GPRS:n datansiirtonopeuteen. Tämä työ käsittelee myös lyhyesti GSM-järjestelmää, koska lukijan on näin helpompaa ymmärtää myös GPRS-järjestelmän vaatimia teknisiä muutoksia. Tämä diplomityö on tehty osana Nokia Matkapuhelimet Oyj:ssä käynnissä olevaa GPRS tuotekehitysprojektia. Työn tuloksia käytetään testauksen tukena ja niitä on käytetty apuna RLC-kerroksen luotettavuustestauksen suunnittelussa.
Resumo:
We perform Hartree calculations of symmetric and asymmetric semi-infinite nuclear matter in the framework of relativistic models based on effective hadronic field theories as recently proposed in the literature. In addition to the conventional cubic and quartic scalar self-interactions, the extended models incorporate a quartic vector self-interaction, scalar-vector non-linearities and tensor couplings of the vector mesons. We investigate the implications of these terms on nuclear surface properties such as the surface energy coefficient, surface thickness, surface stiffness coefficient, neutron skin thickness and the spin-orbit force.
Resumo:
Mesozoic and Neogene carbonates located in the Valencia Trough (offshore Spain, western Mediterranean Sea)are oil reservoirs. This paper investigates the diagenetic evolution of the Upper Jurassic limestones, currently dolomitized, that constitute the main reservoir of the Casablanca oil field. Core samples from Casablanca-1A well have been studied to determine the diagenetic products and their relation with porosity evolution, and to reconstruct the fluid flow history prior to and during oil emplacement. On the basis of petrological observations and geochemical analyses (major, minor and trace element composition and oxygen, carbon and strontium isotope composition), a major dolomitization event is recognized postdating subaerial exposure, erosion and karstification. The dolomitization event originated two replacive dolomites (RD1 and RD2) and two dolomite cements (saddle dolomite cement, SDC, and milky-white dolomite cement, MDC)which are partially cogenetic. RD1, RD2 and SDC precipitated at increasing temperatures (over 60ºC and below 110ºC), probably from meteoric water mixed with marine water. The last dolomite type milky-white dolomite cement) precipitated with increasing burial conditions and by arrival of hydrothermal fluids during the Miocene. The post-dolomitization sequence comprises precipitation of calcite cement and partial calcitization of all previous dolomites. The oxygen, carbon and strontium isotope compositions suggest that this calcite cementation occurred from meteoric waters mixed with Burdigalian - Langhian marine waters trapped in the sediments and expelled by compaction in the moderate to deep burial realm. Normal faults were the conduits for upward migration of these fluids as well as for later oil expulsion from the Burdigalian - Langhian source rocks. Late corrosion associated with organic acid-enriched fluids took place prior or simultaneously to oil migration during the Pliocene, enhancing porosity and increasing eservoir quality.
Resumo:
We show that the coercive field in ferritin and ferrihydrite depends on the maximum magnetic field in a hysteresis loop and that coercivity and loop shifts depend both on the maximum and cooling fields. In the case of ferritin, we show that the time dependence of the magnetization also depends on the maximum and previous cooling fields. This behavior is associated to changes in the intraparticle energy barriers imprinted by these fields. Accordingly, the dependence of the coercive and loop-shift fields with the maximum field in ferritin and ferrihydrite can be described within the frame of a uniform-rotation model considering a dependence of the energy barrier with the maximum and the cooling fields.
Resumo:
microRNAs (miRNAs) are small non-coding RNAs that regulate various biological processes. Cell-free miRNAs have been proposed as biomarkers of disease, including diagnosis, prognosis, and monitoring of treatment responses. These circulating miRNAs are highly stable in several body fluids, including plasma and serum; hence, in view of their potential use as novel, non-invasive biomarkers, the profiles of circulating miRNAs have been explored in the field of anti-doping. This chapter describes the enormous potential of circulating miRNAs as a new class of biomarkers for the detection of doping substances, and highlights the advantages of measuring these stable species over other methods that have already been implemented in anti-doping regimes. Incorporating longitudinal measurements of circulating miRNAs into the Athlete Biological Passport is proposed as an efficient strategy for the implementation of these new biomarkers. Furthermore, potential challenges related to the transition of measurements of circulating miRNAs from research settings to practical anti-doping applications are presented.