An Investigation of a Particular Weldment Failure

Two sets of weld-test coupons, supposedly made under identical conditions, were submitted to this institution last year for approval and certification under the A.S.M.E. Welder's Qualification Code. The first set of coupons was unsatisfactory. The second set, made by the same operators one month later, was satisfactory.

Rugose Corals of the Madison Group

One of the best types of index fossils, and one which occurs most plentifully in the Madison group of formations in Montana, and yet, one which has been little studied, is the group of rugose, or cup, corals. Perhaps this group of fossils has not been studied in detail because their distinguishing characteristics are mainly internal, and labo­ratory preparation in the form of thin section or polished surfaces is necessary to bring out these characteristics.

Kibbey Sandstone in Montana

Much attention has recently been given, by geolog­ists, to prolific water bearing horizon and a potent­ial oil horizon, known as the Kibbey sandstone, which lies deeply buried under much of central Montana. In some local­ities the sandstone is dry, and its identification in cut­tings from deep wells has in many cases proved difficult.

The Anodic Polishing of Copper in Solutions of Orthophosphoric Acid

The electrolytic cleaning of metals by anodic methods has been known for many years. It was recognized long ago that when the temperature and concentration of the electro­lyte were properly regulated, bright clean surfaces were obtained.

The Problem of the Tensleep Sandstone

Sandstone is probably one of the most important groups of rocks in existence today. The economic importance of so insignifi­cant a thing as a mass of sand grains grows with the true reality of the situation. By increasing our knowledge of grains of sand, or particles of sandstone in all their ram­ifications, it would undoubtedly reflect upon our everyday life by increasing commercial possibilities of an undevel­oped natural resource of Montana.

Electro-Deposition of Iron from a Chloride Bath

Iron was electro-deposited from a ferrous chloride bath. Studies were made of deposits formed when current density was varied, and fin­ally when both current density and temperature were changed. An attempt was made to lay the ground work for a long range study of the chloride bath, and to determine the most simple conditions possible for obtaining a smooth, even, and thick deposit.

Corrosion Testing of Iron-Tin Alloys by the Salt Spray Method

The purpose of this study was to determine the rela­tive rate of corrosion of iron-tin alloys containing low percentages of tin. Since in the world today, a great deal of work is being done to develop large tin deposits and new methods devised to treat these ores, it is possible that the metal will become abundant and will obtain a more important position in the metal industry.

An Investigation Into the Adaption of the Induction Furnace for Determining the Equilibrim Diagram of the System Cu2S-FeS

This investigation was started in an effort to find an accurate and efficient method of determining the freezing points of ferrous and cuprous sulphides, mixtures of the two substances, and from this to establish the liquidus line of the equilibrium dia­gram.

A Preliminary Study of the Separation of the Copper Sulfides from Sphalerite and the Effect of Certain Reagents on Some of the Pure Copper Minerals in Synthetic Mixtures

The problem of separating the copper sulfide minerals from sphalerite, in copper - zinc ores, has been a difficult one. This is largely due to the lack of adequate research and the small amount of data obtainable on the behavior of copper and zinc sulfide minerals in flotation circuits.

The Separation of Tungstic Oxide from Scheelite and its Subsequent Reduction with Hydrogen

The largest known deposits of tungsten ores occur in the continuation of the Indo-Malayan Mountains, which extends through Burma, Malaya, China, Japan, and Chosen. Production of tungsten concentrates was started in 1910 in Burma, and in 1911 this country was the world's largest producer. China produced but little until 1916, but has since supplied over fifty per cent of the world's requirements.

Mayflower, Renova Basin, and South Boulder Creek Areas

In Montana at the turn of the century a great many men sought the riches buried in the earth's crust. Prospectors fanning out from Butte and other early Montana mining areas located veins at the Mayflower, Renova, and Gold Hill areas.

Insoluble Residues of Five Sections of the Amsden Formation

The term, "insoluble residue," as used in this report is that portion of the original rock sample remaining after the sample has been digested by a mixture of one part hydrocloric acid and two parts water. The remains or insoluble residue from this acid treatment may vary from nothing to I00 percent.

A Study of the Physical Properties of Low Tin Solders

In 1947, out of the 100,000 long tons of tin con­sumed in the United States, 25,000 tons went into solder. Tin plate took 39,000 tons while babbit, bronze and coll­apsible tubes accounted for approximately 17,000 tons. Solder ranked second to tin plate and required more than the next three major uses combined.

A Geological Report on South Boulder Canyon and The Mayflower Mine-Renova Areas

The purpose of this report is to serve as a written explanation of the accompanying geologic maps and columnar sec­tion. Each year the senior students in mining and geological engineering at the Montana School of Mines spend two weeks in the field where they learn the fundamentals of geologic mapping and related field studies. An additional week is spent at the school where maps are assembled, prints made, end other work is done in preparation for the writing of the report.

The Effect of Manganese and Magnesium on the Hardening of Copper-Aluminum Alloys

During recent years, duralumin and all aluminum alloys have been made the object of much discussion regarding their hardening mechanism. The commercial success of nearly all of the alloys of aluminum and mag­nesium is dependent on their ability to age or precipitation harden.