1.2-μm semiconductor disk laser frequency doubled with periodically poled lithium tantalate crystal

In this letter, we demonstrate an optically pumped semiconductor disk laser frequency doubled with a periodically poled lithium tantalate crystal. Crystals with various lengths were tested for intracavity frequency conversion. The semiconductor disk laser exploited GaInNAs-based active region with GaAsAlAs distributed Bragg mirror to produce emission at 1.2- μm wavelength. The frequency doubled power up to 760 mW at the wavelength of 610 nm was achieved with a 2-mm-long crystal. © 2010 IEEE.

Broadly tunable quantum-dot based ultra-short pulse laser system with different diffraction grating orders

A broadly tunable quantum-dot based ultra-short pulse master oscillator power amplifier with different diffraction grating orders as an external-cavity resonance feedback is studied. A broader tuning range, narrower optical spectra as well as higher peak power spectal density (maximun of 1.37 W/nm) from the second-order diffraction beam are achieved compared to those from the first-order diffraction beam in spite of slightly broader pulse duration from the secondorder diffraction. © The Institution of Engineering and Technology 2013.

InAs/AlSb widely tunable external cavity quantum cascade laser around 3.2 μm

Room temperature, tunable, external-cavity short-wavelength InAs/AlSb quantum cascade laser (QCL) is reported. Wavelength tuning of 85 nm for the spectral range between 3190 nm and 3275 nm has been achieved by rotating the diffraction grating forming the external cavity. To suppress lasing inside the QCL cavity, its ridge was tilted by 7° at the external cavity end. The optimal tilting angle of the laser ridge was chosen by careful consideration of the return losses of the TM-polarized waveguide mode from the diffraction grating in a quasi-Littrow configuration and the Fabry-Pérot feedback from the tilted laser facet. No antireflection coating was used. © 2013 American Institute of Physics.

Quasi-distributed strain sensor incorporating a chirped Moiré fiber Bragg grating

A quasi-distributed strain sensor with an average spatial resolution of 164 µm over a length of 25 mm and a strain sensitivity of 0.8 ± 0.01 pm/µe has been experimentally demonstrated. The sensor was formed by a chirped Moiré fiber Bragg grating written into the core of single-mode optical fiber with a 244-nm continuous-wave laser. © 2005 IEEE.

Unrepeatered transmission through ultra-long fiber laser cavities

We present a study on the potential use of ultra-longlasercavities for unrepeateredfiber communication, based on the theory of nonlinearity management. A comparison is offered between the performance of ultra-longlasers and standard bi-directional distributed amplification schemes in nonrepeated transmission. Links based on both traditional (SMF/DCF) and modern Ultrawave transmissionfibers are considered.

Transmission comparison of ultra-long Raman fibre laser based amplification with first and dual order Raman amplification using 10×118 Gbit/s DP-QPSK

Experimental investigations of 10×118 Gbit/s DP-QPSK WDM transmission using three types of distributed Raman amplification techniques are presented. Novel ultra-long Raman fibre laser based amplification with second order counter-propagated pumping is compared with conventional first order and dual order counter-pumped Raman amplification. We demonstrate that URFL based amplification can extend the transmission reach up to a distance of 7520 km in comparison with 5010 km and 6180 km using first order and dual order Raman amplification respectively. © 2014 IEEE.

Optimization of DFB fiber laser performance based on a superimposed cavities structure

A simple technique based on superimposed cavities structure for direct real-time assessment of a DFB fiber laser mode condition during operation is demonstrated and used to provide a cavity mode conditioning feedback mechanism to optimize output performance. Significant improvements to the output performance and robustness are achieved over the entire pump power range without ambient isolation.

Supermode-noise suppression using a nonlinear Fabry–Pérot filter in a harmonically mode-locked fiber ring laser

A simple efficient method for stabilizing a harmonically mode-locked fiber ring laser is proposed. In this method, a linear optical filter and a nonlinear Fabry–Pérot filter in which the refractive index is optical intensity dependent are located in the laser cavity. The linear filter is used to select a fixed lasing wavelength, and the Fabry–Pérot filter introduces a negative all-optical feedback mechanism that is able to suppress pulse-to-pulse amplitude fluctuations in the laser cavity. The scheme was experimentally demonstrated using a fiber Bragg grating as the linear filter and a laser diode biased below threshold as the nonlinear Fabry–Pérot, and stable harmonically mode-locked pulses with a supermode noise suppression ratio >55 dB were obtained.

Time resolved bit error rate analysis of a fast switching tunable laser for use in optically switched networks

We investigate the use of different direct detection modulation formats in a wavelength switched optical network. We find the minimum time it takes a tunable sampled grating distributed Bragg reflector laser to recover after switching from one wavelength channel to another for different modulation formats. The recovery time is investigated utilizing a field programmable gate array which operates as a time resolved bit error rate detector. The detector offers 93 ps resolution operating at 10.7 Gb/s and allows for all the data received to contribute to the measurement, allowing low bit error rates to be measured at high speed. The recovery times for 10.7 Gb/s non-return-to-zero on–off keyed modulation, 10.7 Gb/s differentially phase shift keyed signal and 21.4 Gb/s differentially quadrature phase shift keyed formats can be as low as 4 ns, 7 ns and 40 ns, respectively. The time resolved phase noise associated with laser settling is simultaneously measured for 21.4 Gb/s differentially quadrature phase shift keyed data and it shows that the phase noise coupled with frequency error is the primary limitation on transmitting immediately after a laser switching event.

A comparison of two distributed large-volume measurement systems:the mobile spatial co-ordinate measuring system and the indoor global positioning system

Advances in the area of industrial metrology have generated new technologies that are capable of measuring components with complex geometry and large dimensions. However, no standard or best-practice guides are available for the majority of such systems. Therefore, these new systems require appropriate testing and verification in order for the users to understand their full potential prior to their deployment in a real manufacturing environment. This is a crucial stage, especially when more than one system can be used for a specific measurement task. In this paper, two relatively new large-volume measurement systems, the mobile spatial co-ordinate measuring system (MScMS) and the indoor global positioning system (iGPS), are reviewed. These two systems utilize different technologies: the MScMS is based on ultrasound and radiofrequency signal transmission and the iGPS uses laser technology. Both systems have components with small dimensions that are distributed around the measuring area to form a network of sensors allowing rapid dimensional measurements to be performed in relation to large-size objects, with typical dimensions of several decametres. The portability, reconfigurability, and ease of installation make these systems attractive for many industries that manufacture large-scale products. In this paper, the major technical aspects of the two systems are briefly described and compared. Initial results of the tests performed to establish the repeatability and reproducibility of these systems are also presented. © IMechE 2009.

RIN transfer in 2nd-order distributed amplification with ultralong fiber lasers

We investigate numerically the effect of ultralong Raman laser fiber amplifier design parameters, such as span length, pumping distribution and grating reflectivity, on the RIN transfer from the pump to the transmitted signal. Comparison is provided to the performance of traditional second-order Raman amplified schemes, showing a relative performance penalty for ultralong laser systems that gets smaller as span length increases. We show that careful choice of system parameters can be used to partially offset such penalty. © 2010 Optical Society of America.

The effects of audio cueing and an instructions, feedback and praise package on the distribution of teacher praise to students of differing on-task levels

In an audio cueing system, a teacher is presented with randomly spaced auditory signals via tape recorder or intercom. The teacher is instructed to praise a child who is on-task each time the cue is presented. In this study, a baseline was obtained on the teacher's praise rate and the children's on-task behaviour in a Grade 5 class of 37 students. Children were then divided into high, medium and low on-task groups. Followinq baseline, the teacher's praise rate and the children's on-task behaviour were observed under the following successively implemented conditions: (l) Audio Cueing 1: Audio cueing at a rate of 30 cues per hour was introduced into the classroom and remained in effect during subsequent conditions. A group of consistently low on-task children were delineated. (2) Audio Cueing Plus 'focus praise package': Instructions to direct two-thirds o£ the praise to children identified by the experimenter (consistently low on-task children), feedback and experimenter praise for meeting or surpassing the criterion distribution of praise ('focus praise package') were introduced. (3) Audio Cueing 2: The 'focus praise package' was removed. (4) Audio Cueing Plus 'increase praise package': Instructions to increase the rate of praise, feedback and experimenter praise for improved praise rates ('increase praise package') were introduced. The primary aims of the study were to determine the distribution of praise among hi~h, medium and low on-task children when audio cueinq was first introduced and to investigate the effect of the 'focus praise package' on the distribution of teacher praise. The teacher distributed her praise evenly among the hiqh, medium and low on-task groups during audio cueing 1. The effect of the 'focus praise package' was to increase the percentage of praise received by the consistently low on-task children. Other findings tended to suggest that audio cueing increased the teacher's praise rate. However, the teacher's praise rate unexpectedly decreased to a level considerably below the cued rate during audio cueing 2. The 'increase praise package' appeared to increase the teacher's praise rate above the audio cueing 2 level. The effect of an increased praise rate and two distributions of praise on on-task behaviour were considered. Significant increases in on-task behaviour were found in audio cueing 1 for the low on-task group, in the audio cueing plus 'focus praise package' condition for the entire class and the consistently low on-task group and in audio cueing 2 for the medium on-task group. Except for the high on-task children who did not change, the effects of the experimental manipulations on on-task behaviour were e quivocal. However, there were some indications that directing 67% of the praise to the consistently low on-task children was more effective for increasing this group's on-task behaviour than distributing praise equally among on-task groups.

Data feedback and behavioural change intervention to improve primary care prescribing safety (EFIPPS) : multicentre, three arm, cluster-randomised controlled trial

Funding and trial registration: Scottish Government Chief Scientist Office grant CZH/3/17. ClinicalTrials.gov registration NCT01602705.

An Audit and Feedback Intervention for Reducing Antibiotic Prescribing in General Dental Practice : The RAPiD Cluster Randomised Controlled Trial

Funding: This study was conducted as part of the TRiaDS programme of implementation research which is funded by NHS Education for Scotland (NES). The Health Services Research Unit which is funded by the Chief Scientist Office of the Scottish Government Health and Social Care Directorates supported the study. The funder had no influence over the design, conduct, analysis and write up of the study.

Dynamics of vector rogue waves in a fiber laser with a ring cavity

A pulse–pulse interaction that leads to rogue wave (RW) generation in lasers was previously attributed either to soliton–soliton or soliton–dispersive-wave interaction. The beating between polarization modes in the absence of a saturable absorber causes similar effects. Accounting for these polarization modes in a laser resonator is the purpose of the distributed vector model of laser resonators. Furthermore, high pump power, high amplitude, and short pulse duration are not necessary conditions to observe pulse attraction, repulsion, and collisions and the resonance exchange of energy between among them. The regimes of interest can be tuned just by changing the birefringence in the cavity with the pump power slightly higher than the laser threshold. This allows the observation of a wide range of RW patterns in the same experiment, as well as to classify them. The dynamics of the interaction between pulses leads us to the conclusion that all of these effects occur due to nonlinearity induced by the inverse population in the active fiber as well as an intrinsic nonlinearity in the passive part of the cavity. Most of the mechanisms of pulse–pulse interaction were found to be mutually exclusive. This means that all the observed RW patterns, namely, the “lonely,” “twins,” “three sisters,” and “cross,” are probably different cases of the same process.