An ab-initio calculation of the Coulomb explosion of N_2 after heavy-ion bombardement

Self-consistent-field calculations for the total potential energy of highly ionized N_2 molecules are presented. We compare these calculations to the experimentally observed energy released in the Coulomb explosion of ionized N_2 molecules created after collision with fast heavy ions. The most important electronic states of the fragment ions are determined.

Modeling, Estimation, and Control of Robot-Soil Interactions

This thesis presents the development of hardware, theory, and experimental methods to enable a robotic manipulator arm to interact with soils and estimate soil properties from interaction forces. Unlike the majority of robotic systems interacting with soil, our objective is parameter estimation, not excavation. To this end, we design our manipulator with a flat plate for easy modeling of interactions. By using a flat plate, we take advantage of the wealth of research on the similar problem of earth pressure on retaining walls. There are a number of existing earth pressure models. These models typically provide estimates of force which are in uncertain relation to the true force. A recent technique, known as numerical limit analysis, provides upper and lower bounds on the true force. Predictions from the numerical limit analysis technique are shown to be in good agreement with other accepted models. Experimental methods for plate insertion, soil-tool interface friction estimation, and control of applied forces on the soil are presented. In addition, a novel graphical technique for inverting the soil models is developed, which is an improvement over standard nonlinear optimization. This graphical technique utilizes the uncertainties associated with each set of force measurements to obtain all possible parameters which could have produced the measured forces. The system is tested on three cohesionless soils, two in a loose state and one in a loose and dense state. The results are compared with friction angles obtained from direct shear tests. The results highlight a number of key points. Common assumptions are made in soil modeling. Most notably, the Mohr-Coulomb failure law and perfectly plastic behavior. In the direct shear tests, a marked dependence of friction angle on the normal stress at low stresses is found. This has ramifications for any study of friction done at low stresses. In addition, gradual failures are often observed for vertical tools and tools inclined away from the direction of motion. After accounting for the change in friction angle at low stresses, the results show good agreement with the direct shear values.

Definición, hipótesis y experimentación en la Ley de Coulomb.

Fue el primero en descubrir las características de las fuerzas entre las cargas eléctricas. Su ley dice: la magnitud de cada una de las fuerzas eléctricas con que interactúan dos cargas puntuales en reposo es directamente proporcional al producto de la magnitud de ambas cargas ....

Demostración experimental de la Ley de Coulomb con el retroproyector.

Se realiza una demostración experimental de la Ley de Coulomb con el retroproyector. EI retroproyector de transparencias permite demostrar experimentalmente la Ley de Coulomb, de una manera rápida y precisa, a un conjunto numeroso de alumnos, de modo que todos ellos participen en la recogida de datos y en la interpretación de resultados. Se muestra esquemáticamente el montaje del experimento en una ilustración y se explica textualmente. La Ley de Coulomb solamente se puede aplicar a aquellas cargas cuyas dimensiones son despreciables comparadas con la distancia que las separa. En nuestros experimentos hemos comprobado que la Ley de Coulomb deja de cumplirse cuando la distancia de separación es inferior a cuatro veces el diámetro de las bolitas. Es decir, si el diámetro de éstas es de 1 cm, la distancia entre ambas bolitas debe ser mayor de 4 cm.

Comprobaci??n de la ley de Coulomb

Se presentan una serie de valores y se adjunta una gr??fica con el fin de representar la exactitud con la que se cumple la ley de Coulumb.

The mapping of the local contributions of Fermi and Coulomb correlation into intracule and extracule density distributions

The contributions of the correlated and uncorrelated components of the electron-pair density to atomic and molecular intracule I(r) and extracule E(R) densities and its Laplacian functions ∇2I(r) and ∇2E(R) are analyzed at the Hartree-Fock (HF) and configuration interaction (CI) levels of theory. The topologies of the uncorrelated components of these functions can be rationalized in terms of the corresponding one-electron densities. In contrast, by analyzing the correlated components of I(r) and E(R), namely, IC(r) and EC(R), the effect of electron Fermi and Coulomb correlation can be assessed at the HF and CI levels of theory. Moreover, the contribution of Coulomb correlation can be isolated by means of difference maps between IC(r) and EC(R) distributions calculated at the two levels of theory. As application examples, the He, Ne, and Ar atomic series, the C2-2, N2, O2+2 molecular series, and the C2H4 molecule have been investigated. For these atoms and molecules, it is found that Fermi correlation accounts for the main characteristics of IC(r) and EC(R), with Coulomb correlation increasing slightly the locality of these functions at the CI level of theory. Furthermore, IC(r), EC(R), and the associated Laplacian functions, reveal the short-ranged nature and high isotropy of Fermi and Coulomb correlation in atoms and molecules

Análisis de impacto ambiental: friction drilling vs taladrado convencional.

[ES]Se trata de un proyecto en el que se describe y profundiza en el proceso de fabricación denominado friction drilling y donde se compara su impacto ambiental frente al del taladrado convencional utilizando el análisis de ciclo de vida como herramienta.

A note on boundary layer friction in baroclinic cyclones

The interaction between extratropical cyclones and the underlying boundary layer has been a topic of recent discussion in papers by Adamson et al (2006) and Beare (2007). Their results emphasise different mechanisms through which the boundary layer dynamics may modify the growth of a baroclinic cyclone. By using different sea-surface temperature distributions and comparing the low-level winds, the differences are exposed and both of the proposed mechanisms appear to be acting within a single simulation.

Toughness, the shearing of self-mated junctions and friction

Since ductile fracture (rupture) is the process by which junctions are separated and which prevents ever-increasing plasticity and junction growth, it is argued that models of friction ought to include toughness as well as yield strength. An expression for the coefficient of sliding friction is derived using ductile fracture mechanics. The predictions are quite reasonable.

Extending the friction cone algorithm for arbitrary polygon based haptic objects

Most haptic environments are based on single point interactions whereas in practice, object manipulation requires multiple contact points between the object, fingers, thumb and palm. The Friction Cone Algorithm was developed specifically to work well in a multi-finger haptic environment where object manipulation would occur. However, the Friction Cone Algorithm has two shortcomings when applied to polygon meshes: there is no means of transitioning polygon boundaries or feeling non-convex edges. In order to overcome these deficiencies, Face Directed Connection Graphs have been developed as well as a robust method for applying friction to non-convex edges. Both these extensions are described herein, as well as the implementation issues associated with them.

Force shading and bump mapping using the friction cone algorithm

Previous work has presented the friction cone algorithm, a generalised method to resolve forces on a simulated haptic object when two or more fingers are in contact. Two extensions to the friction cone algorithm are presented: force shading and bump mapping. Force shading removes the discontinuities that are present when transitioning from one face to the next, whilst bump mapping provides a mechanism for rendering haptic textures on polygonal surfaces. Both these extensions can be combined whilst still maintaining the friction cone algorithm's intrinsic ability to simulate arbitrarily complex friction models.