Properties of Hydraulic Jump over Apparent Corrugated Beds

The characteristics of hydraulic jumps were investigated for three shapes of artificial apparent corrugated beds in a horizontal rectangular flume. Rectangular, triangular, and circular-shaped tire waste corrugated beds were used. Froude number ranged from 2.75 to 4.25. The experimental observations included water surface profiles, bed shear stress, and the hydraulic jump length. Results showed that the shape of the corrugation had relatively insignificant effects on hydraulic jump properties for small Froude numbers. The rectangular, triangular, and circular-shaped corrugated beds reduced the hydraulic jump length by up to 7, 10, and 11%, respectively. The corrugated bed also reduced the tailwater depth by up to 11.5% compared with the smooth bed. The apparent conditions of corrugated bed reduced the hydraulic jump relative length and height by about 0.4 and 0.5, respectively. The circular-shaped tire waste was found to be more effective in reducing the length and depth of the hydraulic jump.

Millimeter Wave Amplitude Comparison Monopulse Using a Waveguide Rotman Lens

A 94 GHz waveguide Rotman lens is described which can be used to implement an amplitude comparison monopulse RADAR. In transmit mode, adjacent dual beam ports are excited with equal amplitude and phase to form a sum radiation pattern, and in receive mode, the outputs of the beam port pairs are combined using magic tees to provide a sum and a difference signal which can be used to calculate an angular error estimate for target acquisition and tracking. This approach provides an amplitude comparison monopulse system which can be scanned in azimuth and which has a low component count, with no requirement for phase shift circuitry in the array feed lines, making it suitable for mm-wave frequencies. A 12 input (beam ports), 12 output (array ports) lens is designed using CST Microwave Studio, and the predicted results are presented.

Propagation Characteristics of Groove Gap Waveguide Below and Above Cutoff

Recently, gap waveguides have been shown as a potential alternative to conventional waveguides in the millimeterwave band. Until now, Groove Gap Waveguide (GGW) has been studied through direct correspondence with rectangular waveguide with the same physical dimensions. However there have been observed differences in the above cutoff propagation characteristics between these two waveguide types. Furthermore, the behavior of GGW below cutoff remains unknown. This work presents a discussion of both below and above cutoff propagation characteristics of GGW, and introduces a simple model that explains the observed GGW behavior and establishes well its propagation characteristics. Two TRL calibration kits have been manufactured, and the measurements have good agreement with the proposed analysis model results.

A Fast Analysis Method for the Groove Gap Waveguide Using Transmission Line Theory

The Groove Gap Waveguide (GGW) shows a behavior similar to the classical rectangular waveguide (RWG), but it is formed by two pieces which do not require metal contact. This feature suggests the GGW as a suitable alternative to the RGW for mm-wave frequencies, where ensuring the proper metal contact according to the wavelength size results challenging. Nevertheless, there is a lack of effective analysis tools for the complex GGW topology, and assuming a direct equivalence between the RGW and the GGW is too rough, so that dilatory full-wave simulations are required. This work presents a fast analysis method based on transmission line theory, which establishes the proper correspondence between the GGW and the RWG. In addition, below cutoff behavior of the GGW is studied for the first time. Several numerical tests and two manufactured prototypes validate the proposed method, which seems very adequate to optimize future GGW structures.

Compact dielectric-filled waveguide filters and diplexers

This paper presents electromagnetic simulations of dielectric-filled rectangular waveguide bandpass filter structures with microstrip to waveguide transitions as well as a diplexer based on such filters for modern wireless systems. The two bandpass filters have been designed and simulated at centre frequencies of 11.85 and 14.25 GHz, respectively. A significant size reduction is achieved through dielectric filling.

Ultra compact pseudo-elliptic inline waveguide bandpass filters using bypass coupling

This paper presents an ultra compact waveguide bandpass filter that exhibits a pseudo-elliptic response. The transmission zero created in the upper stopband to form a rapid roll off is produced through a bypass coupling with higher order modes. A 3rd order filter is designed at the centre frequency of 9.4 GHz with a 5.3% fractional bandwidth. The proposed structure's size is 38% smaller than one of a 3rd order E-plane extracted pole filter with comparable response. Additionally, this configuration allows larger span of different bandwidths. The filter has been fabricated and tested using E-plane waveguide technology, which has benefits of being inexpensive and having mass producible capabilities. Measurements of such a fabricated filter validate the simulated results.

Ultra compact inline E-plane waveguide extracted pole bandpass filters

This letter presents an ultra compact extracted pole E-plane filter. The proposed structure can achieve up to 65% size reduction in comparison with a standard extracted pole filter designed at 9.5 GHz centre frequency with a 3% fractional bandwidth. The filter has been fabricated and tested using E-plane waveguide technology. Measurements on a fabricated filter confirm the accuracy of the design method.

Optically reconfigurable E-plane waveguide resonators and filters

This paper presents an optically reconfigurable E-plane waveguide resonator and filter. N-type silicon dice doped with phosphorus is used as the switching element and is connected to the edge of a metallic fin. Illumination of the silicon dice allows realization of a different length of the fin, thus creating a shift in resonant frequency of the structure. Frequency tuning range up to about 5.2% is achieved for the resonator as well as the filter. Measurements on a fabricated optically reconfigurable resonator confirm the accuracy of the design procedure. Measured responses show good agreement with simulation.

Corrugated horn antenna for a CosmoGal satellite with reduced dimensions

This paper presents the design methodology for the creation of corrugated horn antennas for the CosmoGal satellite. The mission will collect the radiation of the cosmic microwave background, by a radiometer in three different radio astronomy frequency bands (10.6-10.7GHz; 15.35-15.4GHz; 23.6-24GHz). It is discussed the design of several types of horns, simulated with the CST software. The best result points to a choked Gaussian corrugated horn antenna, with directivity of 23 dBi, side lobes 35 dB below and cross polarization better than -45 dB. Plus, with the advantage of having a small dimension, with a total length of only 7.43λ © 2014 IEEE.

New Simulated Corrugated Scaltering Surface Giving Widebandcharacter I Sti Cs

Simultaneous elimination of specular reflection and backscattered power from a plane metallic surface by simulated corrugated surfaces of constant period and variable strip width for TM polarisation is reported. This new configuration offers almost a ten-fold frequency bandwidth compared with a regularly spaced strip grating of the same size.

Compact asymmetric coplanar waveguide filter

The design and implementation of a novel asymmetric coplanar waveguide (ACPW ) band rejection filter using defected ground structure ( DGS) is presented . The proposed ACPW DGS technology provides band gap characteristics with only one cell in the lateral ground plane . The equivalent circuit model of the proposed DGS unit section is described . Measurements of ACPW DGS showed good agreement with simulation and the proposed model

Corrugated Flanged Horn Feed for Offset Paraboloidal Reflectors

A technique for improving the coupling between a feed horn and reflector by using corrugated metallic flanges is presented. Experimental data for flanges of varying parameters are given and theoretical explanation is supplemented

Axially Symmetric Radiation Patterns from Corrugated

A modified H-plane sectoral horn antenna with identical E- and'H- plane.patterns over the X-band frequency is discussed. This system has significantly reduced side lobes and hack lobes. Half=power beam width and gain of the antenna are also improved with enhanced matching , Experimental results for a number of horns with various flanges are presented . These find practical application for illuminating symmetric antennas like paraboloids and polarization measurements in radio astronomy, etc. Compared to the fixed pyramidal horns. the present system offers great convenience in trimming the antenna characteristics