Frameless linac-based (Novalis TX) stereotactic treatment for vestibular schwannoma that extend distally into the iac (Internal Acoustic Canal): an analysis of the dose to the cochlea

Objectives: We compare the dose parameters between 3 different radiosurgery delivery techniques which may have an impact on cochlea function. Methods: Five patients with unilateral vestibular schwannoma (VS) were selected for this study. Planning procedure was carried out using the BrainLAB® iPlan planning system v. 4.5. For each patient three different planning techniques were used: dynamic arc (DA) with 5 arcs per plan, hybrid arc (HA) with 5 arcs per plan and IMRT with 8 fields per plan. For each technique, two plans were generated with different methods: with the first method (PTV coverage) it was the goal to fully cover the PTV with at least 12 Gy (normalization: 12 Gy covered 99% of the PTV) and with the second method (cochlea sparing) it was the goal to spare the cochlea (normalization: 12 Gy covers 50% of the PTV/V4Gy of cochlea lower than 1%). Plan evaluation was done considering target volume and coverage (conformity and homogeneity) and OAR constraints (mean (Dmean) and maximum dose (Dmax) to cochlea, Dmax to brainstem and cochlea). The total number of monitor units (MU) was analyzed. Results: The median tumor volume was 0.95 cm³ (range, 0.86-3 cm³). The median PTV was 1.44 cm³ (range, 1-3.5 cm³). The median distance between the tumor and the cochlea's modiulus was 2.7 mm (range, 1.8-6.3 mm). For the PTV coverage method, when we compared the cochlear dose in VS patients planned with DA, HA and IMRT, there were no significant differences in Dmax (p = 0.872) and in Dmean (p= 0.860). We found a significant correlation (p< 0.05) between the target volume and the cochlear Dmean for all plans with Pearson's coefficient correlation of 0.90, 0.92 and 0.94 for the DA, HA and IMRT techniques, respectively. For the cochlea sparing method, when we compared the cochlear dose in VS patients planned with DA, HA and IMRT, there were no significant differences in Dmax (p = 0.310) and in Dmean (p= 0.275). However, in this group the V4Gy of the ipsilateral cochlea represents less than 1%. When using the HA or IMRT technique, the homogeneity and conformity in the PTV, but also the number of MUs were increased in comparison to the DA technique. Conclusion: VS tumors that extend distally into the IAC had an equivalent sparing of cochlea with DA approach compared with the HA and IMRT techniques. Disclosure: No significant relationships.

The Law of the WTO and the Communications Law of the EC : On a Path of Harmony or Discord?

This paper presents an overview of the law of the World Trade Organization (WTO) relevant to telecommunications services and correlates this body of law with the current regulatory framework for electronic communications networks and services in the European Community. The latter has been adapted to meet the challenges of technological and market developments in communications, epitomized by the processes of digitization, enhanced transport networks and convergence. The novel solutions embodied in the EC electronic communications regime, notably, a new design of the Significant Market Power mechanism, a projected withdrawal of sector specific regulation and an affirmation of the principle of technological neutrality, pose interesting questions as to the conformity of this reformed EC communications law with the WTO rules on telecommunications services and the obligations of the European Communities and their Member States. Looking beyond the WTO legal compatibility test, essential questions regarding the need for evolution of the WTO telecommunications rules are raised. The present paper contributes to the ongoing debate in that context in light of the EC experience.

Interobserver variations of target volume delineation in multicatheter partial breast brachytherapy after open cavity surgery

PURPOSE To investigate interobserver variations of target volume delineations in accelerated partial breast irradiation with multicatheter brachytherapy (BT) and to assess the impact of guidelines on consistency of contouring. METHODS AND MATERIALS A contouring study with two phases in interstitial accelerated partial breast irradiation after open cavity surgery was conducted by the Groupe Européen de Curiethérapie-European Society for Radiotherapy and Oncology Breast Cancer Working Group. Contours of cavity and planning target volume (PTV) on preimplant and postimplant CT images were delineated. In Phase 1, nine radiation oncologists defined the target volumes of 5 patients, whereas in Phase 2, four observers draw the contours of 4 patients applying guidelines. In Phase 1, experience in breast BT after open cavity surgery was assessed. The delineations were compared between Phase 1 and Phase 2, the impact of guidelines was assessed, and cavity visualization score was related to consistency of delineations. RESULTS Significant interobserver variability in delineations of lumpectomy cavity and PTV was observed among the participants. Observers with BT experience after open cavity surgery outlined the cavity and PTV more consistently (conformity indexgen: 0.52 vs. 0.48 and 0.59 vs. 0.55 for preimplant and postimplant cavities). For all volumes, the mean Vmax/Vmin was 2.2 vs. 2.8. Having used guidelines all conformity indices increased significantly. For cavity, the increase was 14% and 11%, whereas for the PTV, 28% and 17% on the preimplant and postimplant CT images, respectively. A strong correlation was found between consistency of contours and cavity visualization score. CONCLUSIONS Simple guidelines on defining the lumpectomy cavity significantly increased the consistency of contouring. Reliable consistency of target volume definition can be expected only for good cavity visibility.

Implications of proposed fibromyalgia criteria across other functional pain syndromes

OBJECTIVES In 2010, the American College of Rheumatology (ACR) proposed new criteria for the diagnosis of fibromyalgia (FM) in the context of objections to components of the criteria of 1990. The new criteria consider the Widespread Pain Index (WPI) and the Symptom Severity Score (SSS). This study evaluated the implications of the new diagnostic criteria for FM across other functional pain syndromes. METHOD A cohort of 300 consecutive in-patients with functional pain syndromes underwent a diagnostic screen according to the ACR 2010 criteria. Additionally, systematic pain assessment including algometric and psychometric data was carried out. RESULTS Twenty-five patients (8.3%) had been diagnosed with FM according to the ACR 1990 criteria. Twenty-one of them (84%) also met the new ACR 2010 criteria. In total, 130 patients (43%) fulfilled the new ACR 2010 criteria. A comparison of new vs. old cases showed a high degree of conformity in most of the pain characteristics. The new FM cases, however, revealed a pronounced heterogeneity in the anatomical pain locations, including several types of localized pain syndromes. Furthermore, patients fulfilling the ACR 2010 FM criteria differed from those with other functional pain syndromes; they had increased pain sensitivity scores and increased psychometric values for depression, anxiety, and psychological distress (p<0.01). CONCLUSIONS FM according to the ACR 2010 criteria describes the 'severe half' of the spectrum of functional pain syndromes. By dropping the requirement of 'generalized pain', these criteria result in a blurring of the distinction between FM and more localized functional pain syndromes.

Ventilation/perfusion SPECT or SPECT/CT for lung function imaging in patients with pulmonary emphysema?

PURPOSE To evaluate the utility of attenuation correction (AC) of V/P SPECT images for patients with pulmonary emphysema. MATERIALS AND METHODS Twenty-one patients (mean age 67.6 years) with pulmonary emphysema who underwent V/P SPECT/CT were included. AC/non-AC V/P SPECT images were compared visually and semiquantitatively. Visual comparison of AC/non-AC images was based on a 5-point likert scale. Semiquantitative comparison assessed absolute counts per lung (aCpLu) and lung lobe (aCpLo) for AC/non-AC images using software-based analysis; percentage counts (PC = (aCpLo/aCpLu) × 100) were calculated. Correlation between AC/non-AC V/P SPECT images was analyzed using Spearman's rho correlation coefficient; differences were tested for significance with the Wilcoxon rank sum test. RESULTS Visual analysis revealed high conformity for AC and non-AC V/P SPECT images. Semiquantitative analysis of PC in AC/non-AC images had an excellent correlation and showed no significant differences in perfusion (ρ = 0.986) or ventilation (ρ = 0.979, p = 0.809) SPECT/CT images. CONCLUSION AC of V/P SPECT images for lung lobe-based function imaging in patients with pulmonary emphysema do not improve visual or semiquantitative image analysis.

Dose-painting intensity-modulated proton therapy for intermediate- and high-risk meningioma.

BACKGROUND Newly diagnosed WHO grade II-III or any WHO grade recurrent meningioma exhibit an aggressive behavior and thus are considered as high- or intermediate risk tumors. Given the unsatisfactory rates of disease control and survival after primary or adjuvant radiation therapy, optimization of treatment strategies is needed. We investigated the potential of dose-painting intensity-modulated proton beam-therapy (IMPT) for intermediate- and high-risk meningioma. MATERIAL AND METHODS Imaging data from five patients undergoing proton beam-therapy were used. The dose-painting target was defined using [68]Ga-[1,4,7,10-tetraazacyclododecane tetraacetic acid]- d-Phe(1),Tyr(3)-octreotate ([68]Ga-DOTATATE)-positron emission tomography (PET) in target delineation. IMPT and photon intensity-modulated radiation therapy (IMRT) treatment plans were generated for each patient using an in-house developed treatment planning system (TPS) supporting spot-scanning technology and a commercial TPS, respectively. Doses of 66 Gy (2.2 Gy/fraction) and 54 Gy (1.8 Gy/fraction) were prescribed to the PET-based planning target volume (PTVPET) and the union of PET- and anatomical imaging-based PTV, respectively, in 30 fractions, using simultaneous integrated boost. RESULTS Dose coverage of the PTVsPET was equally good or slightly better in IMPT plans: dose inhomogeneity was 10 ± 3% in the IMPT plans vs. 13 ± 1% in the IMRT plans (p = 0.33). The brain Dmean and brainstem D50 were small in the IMPT plans: 26.5 ± 1.5 Gy(RBE) and 0.002 ± 0.0 Gy(RBE), respectively, vs. 29.5 ± 1.5 Gy (p = 0.001) and 7.5 ± 11.1 Gy (p = 0.02) for the IMRT plans, respectively. The doses delivered to the optic structures were also decreased with IMPT. CONCLUSIONS Dose-painting IMPT is technically feasible using currently available planning tools and resulted in dose conformity of the dose-painted target comparable to IMRT with a significant reduction of radiation dose delivered to the brain, brainstem and optic apparatus. Dose escalation with IMPT may improve tumor control and decrease radiation-induced toxicity.

Volumetric Modulated Arc Therapy Evaluation with the Radiological Physics Center Head and Neck Phantom

Validation of treatment plan quality and dose calculation accuracy is essential for new radiotherapy techniques, including volumetric modulated arc therapy (VMAT). VMAT delivers intensity modulated radiotherapy treatments while simultaneously rotating the gantry, adding an additional level of complexity to both the dose calculation and delivery of VMAT treatments compared to static gantry IMRT. The purpose of this project was to compare two VMAT systems, Elekta VMAT and Varian RapidArc, to the current standard of care, IMRT, in terms of both treatment plan quality and dosimetric delivery accuracy using the Radiological Physics Center (RPC) head and neck (H&N) phantom. Clinically relevant treatment plans were created for the phantom using typical prescription and dose constraints for Elekta VMAT (planned with Pinnacle3 Smart Arc) and RapidArc and IMRT (both planned with Eclipse). The treatment plans were evaluated to determine if they were clinically comparable using several dosimetric criteria, including ability to meet dose objectives, hot spots, conformity index, and homogeneity index. The planned treatments were delivered to the phantom and absolute doses and relative dose distributions were measured with thermoluminescent dosimeters (TLDs) and radiochromic film, respectively. The measured and calculated doses of each treatment were compared to determine if they were clinically acceptable based upon RPC criteria of ±7% dose difference and 4 mm distance-to-agreement. Gamma analysis was used to assess dosimetric accuracy, as well. All treatment plans were able to meet the dosimetric objectives set by the RPC and had similar hot spots in the normal tissue. The Elekta VMAT plan was more homogenous but less conformal than the RapidArc and IMRT plans. When comparing the measured and calculated doses, all plans met the RPC ±7%/4 mm criteria. The percent of points passing the gamma analysis for each treatment delivery was acceptable. Treatment plan quality of the Elekta VMAT, RapidArc and IMRT treatments were comparable for consistent dose prescriptions and constraints. Additionally, the dosimetric accuracy of the Elekta VMAT and RapidArc treatments was verified to be within acceptable tolerances.

Elaboración de vinos : defectos en el proceso que originan costos de no calidad

Los costos de calidad se asocian a su planificación, control, evaluación de la conformidad y a los costos ocasionados por no cumplir con los requisitos de satisfacción de la fábrica o del cliente (productos o servicios con defectos). Los objetivos del trabajo son identificar las causas que provocan la ausencia o pérdida de calidad (no calidad), proponer acciones correctivas en el proceso de elaboración de vinos, midiendo la frecuencia de aparición y clasificando los costos de no calidad. Conocer la frecuencia de aparición de las causas de no calidad en las etapas del proceso de elaboración de vinos permitirá optimizar la gestión y reducir los costos al disminuir sus correcciones. El estudio identifica los factores que alteran la calidad de los vinos. La mayor frecuencia de defectos es de origen prefermentativo, que junto con los de crianza, conservación y originados en el viñedo explican el 79% de los mismos. Los defectos encontrados constituyen costos de prevención y evaluación pero serán falla interna si la bodega está integrada y se atribuirán a falla externa en el caso de productor no integrado. Los establecimientos en los que se pudo identificar y establecer frecuencia de aparición de los defectos que influyen en la calidad del vino son aquellos que tienen algún sistema de gestión de la calidad, ya que han normalizado los registros que actuarán como herramienta de gestión. Los encargados de gerenciar las bodegas deberían conocer los puntos críticos del proceso para realizar la gestión preventiva de los posibles defectos. Los costos que inciden en la calidad del producto a comercializar se deben registrar y controlar, y trazarlos hacia adelante para conocer la incidencia de los mismos en los precios finales, y hacia atrás para que en la planificación de la próxima elaboración se contemple la prevención correspondiente.

Pollen records from two outcrop profiles in the Kakitu Mountain of Tibet

There is a great similarity between pollen types which occur in the early Holocene NE Tibetan pollen spectra and those which are commonly considered to be typical for the Würm Late Glacial period in Central Europe and for the Würm Pleniglacial period in Southern Europe. Evidently, this similarity is due to a remarkable general conformity of plant taxa growing in cold-arid regions of the northern hemisphere. The improvement of the climate and the retreat of the glaciers that commenced at the end of the Würm period had already terminated definitely before 9500 BP. In addition, the climatic situation as well as the vegetation belts must have remained rather constant during the following 3000 yr, i.e. through most parts of the climatic optimum of the Holocene.

Sedimentology on two core from the Bransfield Strait area

The raw material for these investigations are samples from marine (sub)surface sediments around the northern part of the Antarctic Peninsula. They had been sampled in the years 1981 to 1986 during several expeditions of the research vessels Meteor, Polarstern and Walther Herwig. 83 box core, gravity core and dredge samples from the area of the Bransfield Strait, the Powell Basin and the northern Weddell Sea have been examined for their grain-size distribution, their mineralogical and petrographical composition. Silt prevails and its clay proportions exceed 25% wt. in water depths greater than 2000 m. The granulometrical results reveal some typical sedimentation processes within the area of investigation. While turbiditic processes together with sediment input from melting icebergs control the sedimentation in the Weddell Sea, the South Orkney Island Plateau and the Powell Basin, the fine grained material from Bransfield Strait mainly relies on marine currents in the shelf area. In addition, the direct sediment input of coarse shelf sediments from the Bransfield Strait into the Powell Basin through submarine canyons could be proven. Variations in the grain-size composition with sediment depth are smalI. The mineral composition of the clay and fine silt fractions is quite uniform in all samples. There are (in decreasing order): illite, montmorillonite, chlorite, smectite, mixed-Iayers, as well as detrital quartz and feldspars. A petrographically based sediment stratigraphy can be established in using the considerable changes in the chlorite- and Ca-plagioclase portions in samples from Core 224. For this sedimentation area a mean sedimentation rate of 7 cm/1000 a is assumed. Remarkable changes in the portions of amorphous silica components - diatom skeletons and volcanic glass shards - appear all over the area of investigation. They contribute between 4-83 % to the clay and fine silt fraction. Several provinces according to the heavy mineral assemblages in the fine sand fraction can be distinguished: (i) a province remarkably influenced by minerals of volcanic origin south and north of the South Shetland Islands; (ii) a small strip with sediment dominated by plutonic material along the western coast of the Antarctic Peninsula and (iii) a sediment controlled by metamorphic minerals and rock fragments in the area of the Weddell Sea and Elephant Island. While taking the whole grain-size spectrum into account a more comprehensive interpretation can be given: the accessoric but distinct appearance of tourmaline, rutile and zircon in the heavy mineral assembly along the northwestern coast of the Antarctic Peninsula is in agreement with the occurrence of acid volcanic rock pieces in the coarse fraction of the ice load detritus in this region. In the vicinity of the South Shetland Islands chlorite appears in remarkable portions in the clay fraction in combination with leucoxene, sphene and olivine, and pumice as well as pyroclastic rocks in the medium and coarse grain fractions, respectively. Amphiboles and amphibole-schists are dominant on the South Orkney Island Plateau. In the sediments of the northwestern Weddell Sea the heavy mineral phases of red spinel, garnet, kyanite and sillimanite in connection with medium to highgrade metamorphic rocks especially granulitic gneisses, are more abundant. A good conformity between the ice rafted rock sampIes and the rocks in the island outcrops could be proven, especially in the vicinity of offshore islands nearby. On the continent enrichments of rock societies and groups appear in spacious outlines: acid effusive rocks in the west of the ice divide on the Antarctic Peninsula, clastic sedimentites at the tip of the Antarctic Peninsula and granoblastic gneisses in central and eastern Antarctica. Coarse grain detritus with more than 1 cm of diameter must have been rafted by icebergs. These rock fragments are classified as rock types, groups and societies. The spacial distribution of their statistically determined weight relations evidently shows the paths of the iceberg drift and in nexus with already known iceberg routes also point to the possible areas of provenance, provided that the density of sample locations and the number of rock pieces are sufficient.

Japanese import survey : descriptive analysis

Food importers, such as wholesalers and food processing firms, play an important role in sourcing food from abroad. They are also responsible for ensuring that imported food meets the food safety standards of the importing country. Often, assurance of conformity is done in collaboration with exporters. Thus, importers can influence how supply chains in developing countries are organized. This paper uses a unique dataset obtained from the Japanese market to examine how importers select suppliers and assure food quality.

Determinación del contenido de alúmina reactiva de las adiciones puzolánicas naturales y artificiales, por termogravimetría y por el método de Rietveld

Tanto el tema de esta investigación, como sus objetivos, fundamentos, materiales seleccionados y parte experimental para alcanzarlos, han sido promovidos por la situación y el estado de las construcciones de hormigón armado que se comenzaron a realizar en España a partir del año 1975, con hormigones y morteros de cemento que contenían cenizas volantes hasta un 20 %, en principio, y hasta un 35 %, más tarde, de su dosificación de cemento Portland (CP), los cuales y en contra de lo esperado, han demandado y continúan demandando, muy a pesar de sus aparentes bondades de todo tipo que se les atribuían, una necesidad de mejora de sus prestaciones, especialmente, debido a un nivel inesperadamente bajo de la durabilidad de algunas obras construidas con los mismos. Todo era debido, en definitiva, a que las adiciones puzolánicas, naturales y artificiales, tales como las cenizas volantes, referidas antes, se vienen utilizando reglamentariamente para la fabricación de cementos y/o de sus productos derivados, hormigones, morteros y pastas, en la mayor parte de los países industrializados, desde hace ya más de tres décadas aproximadamente, en las mismas condiciones e idénticos usos constructivos que los hormigones y morteros de CP puro, viniendo además, dictada dicha utilización de estos materiales residuales, hoy sub-productos industriales, por cuestiones medioambientales y/o económicas, principalmente, motivo por el cual esta Tesis Doctoral ha pretendido responder también, adecuadamente y de manera esquemática (en forma de diagrama de flujo), a los criterios que deben de tenerse en cuenta a la hora de su selección y caracterización normalizada y reglamentada de estas adiciones minerales activas, sobre todo, antes de su dosificación y uso en forma del denominado cemento Portland con puzolana, o con ceniza volante, o con esquistos calcinados o con puzolanas calcinadas o con humo de sílice, cemento Portland mixto, cemento puzolánico o cemento compuesto, para que dichos problemas no se le produzcan al hormigón armado ni en masa. De aquí el enfoque tan particular y especial de esta investigación, al haberla circunscrito únicamente a las puzolanas naturales y artificiales, por considerarlas todas ellas, independientemente de por su origen, como materiales constituidos por pequeñas fracciones cristalinas distribuidas aleatoriamente en una matriz mayoritariamente vítrea y/o amorfa, la cual es la que le confiere su reactividad con el hidróxido de calcio en forma de cal apagada o de portlandita procedente de la hidratación del CP. A su vez, dichas fracciones vítreas y/o amorfas están constituidas, en su mayor parte, por sílice reactiva, SiO2r-, alúmina reactiva, Al2O3r-, y óxido de hierro reactivo, Fe2O3r-, recibiendo además, en conjunto, el nombre específico de "factores hidráulicos" de la puzolana, los cuales, por lo común, difieren cuantitativamente de sus contenidos totales, determinados por fusión alcalina mediante procedimientos normalizados. De los tres óxidos reactivos mencionados y desde el punto de vista técnico, los más importantes por su mayor presencia en casi todas las puzolanas naturales y artificiales y, también, transcendencia en la durabilidad química que les pueden llegar a conferir al hormigón armado y en masa, mortero o pasta de cemento que las contenga, son la SiO2r- y la Al2O3r-. El primero de los dos, la SiO2r-, reacciona nada más que con la portlandita (y el Ca(OH)2) para formar geles C-S-H, más tarde transformados en tobermoritas o en jennitas, semejantes a los que originan la alita y la belita del CP en su hidratación. Y desde el punto de vista normativo, la presencia de esta fracción silícica reactiva en las puzolanas viene regulada por la norma EN 197-1, de modo general, siendo además referida por la norma EN 450-1:2006, en el contexto de las cenizas volantes en su adición al hormigón, como "un polvo fino de partículas principalmente de forma esférica y cristalina, procedentes de la combustión de carbón pulverizado, que tiene propiedades puzolánicas y que está compuesto fundamentalmente de SiO2 y Al2O3". Además y de acuerdo con la primera de las dos normas, "El contenido de dióxido de silicio reactivo (definido y determinado según la norma EN 196-2 o su equivalente la UNE 80225) no debe ser inferior al 25 % en masa". Por su parte, cuantiosos estudios experimentales realizados por Talero solo y con otros investigadores, han demostrado que si la puzolana no es adecuada en calidad ni en cantidad, la durabilidad del cemento del que forme parte, y, por consiguiente, de los productos derivados que con él se fabriquen, hormigones, morteros, pastas y prefabricados, puede llegar a ser anormalmente baja, porque la alúmina reactiva, Al2O3r-, o alúmina tetra- o penta-coordinada que la constituye, se implica como tal, de una forma muy directa y con resultados totalmente contrapuestos incluso, en los ataques químicos agresivos naturales que se les producen, provenientes de terrenos y aguas selenitosas (sulfatos, que atacan en su caso al propio material hormigón, mortero y pasta que la contiene para formar ettringita de rápida formación, ett-rf, la cual puede llegar incluso a provocar un ataque rápido del yeso), del rocío marino y de las sales de deshielo (cloruros, que atacan, en cambio, a las armaduras de acero del hormigón provocándoles su corrosión electroquímica por "picadura", si bien, en este otro ataque químico, dicha Al2O3r- lo que origina es sal de Friedel de rápida formación, sF-rf, también, cuyo efecto es, en cambio, colmatador y protector, en definitiva, de dicha corrosión electroquímica), del agua de mar (acción agresiva mutua de cloruros y sulfatos), de la carbonatación, de la reactividad árido-álcali, además de intervenir en la liberación del calor de hidratación, así como también, en el comportamiento reológico de sus pastas, etc., acortándoles de este modo su durabilidad prevista y, en ocasiones, muy seriamente incluso. Pero lo más paradójico de todo es, que a pesar de su referido comportamiento totalmente contrapuesto, frente a sulfatos y cloruros, - aún no se dispone de un método de análisis químico para su determinación cuantitativa, que sea además relativamente sencillo en su operatividad, veraz, preciso, de respuesta rápida, desde el punto de vista técnico de la construcción (no más de 28 días), repetible, reproducible, que no implique peligro alguno para la seguridad vital de las personas que lo tengan que manipular y poner en práctica, económico, y que sirva también tanto para investigación -vertiente científica-, como, sobre todo, para control de calidad -vertiente técnica-, - y ni mucho menos tampoco se dispone todavía, de especificación química alguna que precise el contenido máximo de Al2O3r- (%) que tiene que poseer una puzolana natural o artificial, para poder ser añadida al cemento Portland y/o al hormigón que va a estar sometido a un determinado ataque químico agresivo de los mencionados antes, y, en especial, a sulfatos, a cloruros o al agua de mar. Y para mayor justificación de ambas necesidades, se ha de decir también que la vigente Instrucción de Hormigón Estructural EHE-08 no contempla tampoco especificación química alguna sobre los "factores hidráulicos", en general, ni del contenido de Al2O3r-(%) de las cenizas volantes, muy en particular, en su Artículo 30º "Adiciones", ni en ningún otro Artículo, a pesar de que sí contempla, en cambio, - otras especificaciones químicas que carecen del necesario significado en cuanto a la necesidad de llevar explícita o implícitamente, el mensaje de la Durabilidad Química deseado, y - el Artículo 37º, el cual y para mayor abundamiento se titula paradójicamente "Durabilidad del hormigón y de las armaduras". Asimismo, tampoco se contempla en la última versión que acaba de publicarse de la norma EN 197-1 titulada: "Cementos. Parte 1: Composición, especificaciones y criterios de conformidad de los cementos comunes". Ni tampoco, en la norma EN 450-1:2006 titulada "Cenizas volantes para hormigón. Parte 1: Definiciones, especificaciones y criterios de conformidad", ni en la vigente Instrucción española para la Recepción de Cementos, RC-08, ni en la norma ASTM C618-03 tampoco. La única especificación química que ambas normas, la europea y la norteamericana, refieren es aquella que dice que la suma de los contenidos porcentuales de SiO2 total, Al2O3 total y Fe2O3 total, de la puzolana natural o artificial, ha de ser mayor o igual que 70 %, definiendo, además, a las puzolanas de este modo tan genérico: "materiales silíceos o silíceos y aluminosos, que por sí mismos no poseen valor cementante alguno, pero que finamente divididos y en presencia de humedad, reaccionarán químicamente con hidróxido de calcio a temperaturas ordinarias para formar compuestos que poseen propiedades cementantes". Por consiguiente y de acuerdo con todo lo anterior, el objetivo primordial de esta Tesis Doctoral ha sido: Diseñar y poner a punto un nuevo método analítico de utilidad técnica (que la duración máxima del ensayo no sea mayor de 28 días), para determinar el contenido de alúmina reactiva, vítrea o amorfa, Al2O3r-, de las puzolanas naturales y artificiales. Y una vez puesto a punto, validarlo a nivel de su repetibilidad, de acuerdo con parámetros estadísticos apropiados, poniendo especial énfasis en los criterios de aceptación establecidos por la American Association of Official Analytical Chemists (AOAC). Y para conseguirlo, la innovación de esta investigación se ha basado en los siguientes fundamentos generales, a saber: - Toda la alúmina de cualquier puzolana natural o artificial, capaz de ser atacada, disuelta y lixiviada en 28 días, por la portlandita o por el hidróxido de calcio, Ca(OH)2, en medio acuoso, es considerada como alúmina reactiva, Al2O3r-. - Dicha fracción alumínica reactiva de la puzolana natural o artificial se tiene que encontrar, además, en el estado físico-químico de poder reaccionar químicamente también, en presencia de hidróxido de calcio, cloruro de sodio y agua, para originar monocloro¿aluminato de calcio hidratado, C3A·CaCl2·10H2O, o sal de Friedel. Además, dicho estado físico-químico de la puzolana ha de ser acorde con la definición de alúmina reactiva adoptada en esta investigación en razón de las prestaciones reales de durabilidad química que le puede llegar a conferir a los cementos de mezcla y a sus productos derivados, hormigones, morteros y pastas, que se fabriquen con la misma. - La originalidad de este nuevo método analítico, respecto a los demás métodos ya existentes, reside en que la cuantificación de dicha fracción alumínica reactiva de la puzolana natural o artificial, se realiza mediante cálculo estequiométrico, basándose, para ello, en dicha reacción química de formación de sal de Friedel precisamente, tras 28 días de hidratación básica-salina acelerada de la puzolana natural o artificial, habiéndose realizado, además, en esta investigación dicha determinación cuantitativa de la cantidad de sal de Friedel originada por cada puzolana, mediante dos técnicas analíticas instrumentales que fueron las siguientes: el análisis termogravimétrico (variante I ó I-I en su caso) y el método de Rietveld con la difracción de Rayos X en polvo (variante II). - La reacción química de formación de sal de Friedel tras 28 días de hidratación básica-salina acelerada de las puzolanas que se analicen, se optimizó para asegurar que el único compuesto químico de aluminio y cloro formado fuese sal de Friedel nada más (dosificando para ello en cantidad adecuada los reactivos químicos necesarios: Ca(OH)2, NaCl y agua destilada), manteniendo, además y por otra parte, el compromiso apropiado entre el máximo rendimiento de dicha reacción química (ataque, disolución y lixiviación en 28 días, de toda la alúmina reactiva de la puzolana) y el modo y medios más adecuados de acelerarlo para conseguirlo fue a 40°C de temperatura, con agitación constante y cierre hermético del reactor. - La aplicabilidad y selectividad del nuevo método analítico, objeto de esta Tesis Doctoral, fue estudiada con una serie de puzolanas naturales y artificiales españolas, silíceas y/o silíceas y aluminosas en naturaleza, que fueron las siguientes: M0 (metacaolín 0), M1 (M0 con 50 % de cuarzo), C y L (puzolanas naturales de las Islas Canarias), CV10 y CV17 (cenizas volantes), A (puzolana natural de Almagro), O (puzolana natural de Olot) y HS (humo de sílice). - Todas las adiciones minerales anteriores cumplieron con los principales requisitos físicos y químicos que son preceptivos para poder considerarlas, antes de todo, como puzolanas, lo que era indispensable y de obligado cumplimiento, para poderles determinar su contenido total de Al2O3r- (%) mediante el nuevo método analítico. Estos condicionantes fueron los siguientes: grado adecuado de finura de molido o tamaño medio de partícula (según la norma EN 451-2), haber sido analizadas químicamente antes de todo (según la norma EN 196-2 ó la ASTM C311), con el fin de determinarles especialmente, sus contenidos totales de SiO2 (%), Al2O3 (%) y Fe2O3 (%), haberles determinado, además, su contenido de sílice reactiva, SiO2r- (%) (según la norma UNE 80225), y haber cumplido con el ensayo de puzolanicidad o de Frattini (según la norma EN 196-5) a la edad de 28 días al menos. Este último requisito, otrora de obligado cumplimiento hasta el año 1988, para cualquier puzolana natural y artificial que una fábrica de cementos pretendiera introducir en el proceso de fabricación de un nuevo cemento puzolánico o cemento tipo CEM IV, ha logrado así, que se tenga que volver utilizar de nuevo de forma obligada con esta Tesis Doctoral. Y los resultados obtenidos con el nuevo método analítico de los contenidos de Al2O3r-(%) de las puzolanas seleccionadas, fueron los siguientes: - Mediante su variante I: M0 29.9 %, M1 16.9 %, CV10 11.4 %, L 12.3 %, C 12.6 %, A 8.0 %, CV17 9.5 % y O 6.3 % de Al2O3r-, y - Mediante su variante II: M0 30.7 %, M1 15.4 %, CV10 14.7%, L 11.8 %, C 11.1 %, A 8.9 %, CV17 9.6 % y O 6.8 % de Al2O3r-. Finalmente, todos ellos fueron contrastados, además, mediante la calibración y validación del nuevo método analítico, con los valores de referencia obtenidos de esas mismas puzolanas, los cuales se les habían determinado mediante el método de Florentín, consistente en atacar, disolver y lixiviar también toda la fracción alumínica soluble de la puzolana (y además, aquella silícica y férrica que la constituyen a la par), pero, en especial, su contenido total de alúmina reactiva, mediante un ataque básico (con Ca(OH)2 en medio acuoso a temperatura del laboratorio, habiendo sido, además, su duración hasta 1 año), seguido de otro ácido (con HCl, d = 1.12), habiéndose obtenido esta vez los siguientes resultados de sus contenidos de Al2O3r- (%): M0 28.8 %, M1 16.7 %, CV10 9.7 %, L 11.2 %, C 12.2 %, A 13.0 %, CV17 10.6 % y O 9.5 %. Dicha validación realizada ha puesto de manifiesto, en términos generales, que el nuevo método analítico es más fidedigno que el de Florentín, por lo que resulta ser totalmente apropiado para obtener los resultados que se han pretendido, además de proporcionarlos en un espacio de tiempo relativamente corto (28 días a lo sumo) y a un coste económico razonable por no elevado (salvo error u omisión y libre de impuestos directos e indirectos, el coste económico estimado de la variante I estaría en torno a 800.00 - 900.00 €/puzolana -caso más probable-, y aproximadamente una tercera parte nada más, en el caso de que la edad máxima del ensayo acelerado sea 7 días nada más -caso menos probable-), y, por consiguiente, técnicamente aceptable, al cumplir, además, en todo el rango considerado de variabilidad posible de concentraciones o contenidos del analito buscado en la puzolana, con tales parámetros de validación como son: linealidad (los resultados obtenidos son directamente proporcionales a la señal-respuesta instrumental recibida), sensibilidad, precisión excelente, repetibilidad satisfactoria de los valores obtenidos de los contenidos de Al2O3r- de todas y cada una de las adiciones puzolánicas seleccionadas, confirmando, por ello, la universalidad de su uso. Finalmente, las ventajas del nuevo método analítico, respecto a los métodos ya existentes recopilados de la bibliografía (el método de Florentín, el método de López Ruiz -HF 40 % y HNO3 2N-, el método de Murat y Driouche para arcillas -HF 0.5M-, el método de Arjuan, Silbee y Roy para cenizas volantes -HF 1 %- y su modificación por Fernández-Jiménez y cols. -HF 1 %, 27Al NMR MAS y XRD (método de Rietveld)-, y el método de determinación de la relación SiO2r-/Al2O3r- para arcillas y cenizas volantes por Ruiz-Santaquiteria y cols. -HF 1 %, NaOH 8M y ICP-AES-) son, principalmente, estar exento de peligro alguno para la seguridad vital de las personas que lo tengan que manipular y poner en práctica, ser bastante apropiado para control de calidad además de para investigación, su considerable menor coste económico, su relativamente corto espacio de tiempo que se necesita para obtener la respuesta-resultado pretendida (28 días a lo sumo), así como su universalidad y selectividad, puesto que además, su aplicabilidad es para todo tipo de adiciones puzolánicas naturales o artificiales, como así lo demuestran los resultados obtenidos de los materiales puzolánicos naturales y artificiales seleccionados y analizados, en un rango de concentraciones del analito -contenido de alúmina reactiva, Al2O3r- (%)-, desde el 5 % hasta el 30 % en masa, rango éste que, por otra parte, comprende prácticamente TODAS las adiciones puzolanas naturales y artificiales existentes en el mercado transnacional y las aún por existir. Por consiguiente y de acuerdo con lo anterior, el nuevo método analítico, ya sea realizado mediante su variante I o la II, debido, - en primer lugar, a los fundamentados planteamientos relativos a su procedimiento experimental -modus operandi- el cual ha sido aplicado a una amplia gama de puzolanas naturales y artificiales, y - en segundo lugar, debido a la calidad de los resultados obtenidos con un grado de precisión y repetibilidad excelentes, ha demostrado poseer una gran utilidad científica -para investigación-, pero, sobre todo, técnica -para control de calidad de adiciones puzolánicas naturales y artificiales que se adicionan habitualmente al cemento Portland en fábrica y/o a sus hormigones y morteros en planta-, además de ser representativos los valores obtenidos mediante el mismo respecto a la más que probable durabilidad química que cada una de ellas puede llegarle a conferir al hormigón armado y en masa, mortero y pasta del que forme parte, así como también su cantidad adecuada de sustitución parcial de cada cemento Portland para conseguirla, acorde con sus propias prestaciones químico-físicas o físico-químicas que puede llegarle a conferir, según sea su carácter químico (alumínico, alumínico-silícico, silícico-alumínico, silícico-férrico-alumínico o silícico), forma y tamaño medio de su partícula. Por último, el nuevo método analítico ha demostrado cumplir además, con todos los requisitos de obligado cumplimiento que establece la norma ISO/IEC 17025 sobre la calidad y fiabilidad de nuevos métodos o procedimientos analíticos no normalizados todavía, para poder ser propuesto en un futuro próximo, ante la Comisión de AENOR correspondiente, con objeto de comenzar un expediente para su certificación y normalización. ________________________________________________________________________________ Both the subject of this research, its objectives, fundamentals, materials selected and experimental part to achieve, have all been promoted by the situation and the state of reinforced concrete constructions that began performing in Spain from 1975, with concrete and mortars cement containing fly ash up to 20 %, in principle, and later, up to 35 % to its content of Portland cement, which and against expected, demanded a need to improve their performance, especially due to an unexpectedly low level of durability of some works built with them, despite, however, its apparent benefits of all kinds are ascribed to them. Ultimately, the natural or artificial pozzolanic additions, such as fly ash specially, referred to above, have been used with regulation to manufacture cements and/or its derivatives, concretes, mortars, cement pastes, in the most industrialized countries. More than three decades ago, under the same conditions and identical construction mainly uses concretes and mortars plain Portland cement, besides coming, given that use of these waste materials, industrial by-products today for environmental and/or economic issues. For this reason, this Doctoral Thesis aims to answer properly and schematically (in the form of flow chart), the criteria to be taken into account when selection and characterization standardized for these active mineral additions, especially prior to choosing and use in the so-called Portland Cement (PC) pozzolan, or with fly ash or with calcined shales or with calcined pozzolans or with silica fume or PC mixed or pozzolanic cement or compound cement, for that such pathology problems will not occur when reinforced concretes nor mass concretes are used for building. Hence the very particular and special focus about this research, having confined only to the natural or artificial pozzolans, considering them all, regardless of their origin, approach as materials consisting of small crystalline fractions randomly distributed in a largely vitreous and/or amorphous matrix, which confers their reactivity with calcium hydroxide in the form of slaked lime or portlandite from PC. In turn, these vitreous and/or amorphous fractions consist in its greater part, by reactive silica, SiO2r-, reactive alumina, Al2O3r-, and reactive iron oxide, Fe2O3r-, which also receive, in conjunction, the specific name of "hydraulic factors" of the pozzolan. Usually, they all differs in quantity of their respective total contents of the SiO2 (%), Al2O3 (%) and Fe2O3 (%) determined the pozzolan by alkaline fusion by means of standard procedures. Of the three above-mentioned oxides reagents and from the technical point of view, the most important for its increased presence in every one of the natural or artificial pozzolans and also significance in the chemical durability that can get them to give the concrete mortar or cement paste which contain them, are SiO2r- and Al2O3r-. From the first two, the SiO2r- reacts with portlandite only, released in the hydration of the PC (and with Ca(OH)2), to form C-S-H gels, transformed in tobermorites or jennites later on, similar to C-S-H gels also originating from the alite and belite hydration in the CP. From the standardization criteria point of view, the presence of this silicic fraction in pozzolans is regulated at first, by the European standard EN 197-1, in general, also being referred by the EN 450-1:2006, in the context of the fly ash in addition to the concrete, as a "fine powder of spherical particles mainly crystalline form. It is from the combustion of pulverized coal, which have pozzolanic properties and is mainly composed of SiO2 and Al2O3". In addition and according to the EN 197-1 standard, the reactive silica content (which can be defined and determined in accordance with EN 197-1 standard or its UNE 80225 standard) must not be lower than 25 % of its mass. Meanwhile, considerable experimental studies by Talero and Talero et al, have shown that if the pozzolan is not adequate in quality nor quantity, the durability of cement that is part and, therefore, of its derivative products, concretes, mortars and pastes cement, can become abnormally low because its reactive alumina, Al2O3r- (%), content or tetra- or penta-coordinated alumina which involves itself in a very direct and totally mixed and conflicting results even at all aggressive chemical attack natural to produce to the concrete, mortar and paste with inadequate natural and/or artificial pozzolans, such as those from the selenitous land and waters (sulfates, strikes if the material itself concrete, mortar and paste that contain them, for rapid forming ettringite form, ett-rf, which can even cause rapid gypsum attack to said concrete). In contrast, sea spray and de-icing salts (chlorides strikes the reinforced steel concrete causing them electrochemical corrosion by "bite", although in that other chemical attack, such Al2O3r- causes rapid Friedel's salt formation, Fs-rf, too, to cause protector effect of the electrochemical corrosion of reinforcements for these chlorides), seawater (mutual aggressive action of chlorides and sulfates), carbonation, alkali-silica reaction, and, in addition, to influence the release of hydration heat, as well as in the rheological behavior of the pastes, etc., decreasing/shorting them thus their expected durability and sometimes even very seriously. But the most ironic thing is, that despite its referral totally opposed, compared to sulfates and chlorides, behaviour, - far not available is, a chemical analysis method for its quantitative determination, which is also relatively simple in operation, accurate, precise, rapid response, from a technical point of view for building (no more than 28 days), repeatable, reproducible, not involving danger to life safety of the people who need to manipulate and implement, economic, and also serve for both scientific research and technical side, and - has yet to be any chemical specification that sets maximum levels for Al2O3r-(%) in the natural or artificial pozzolan to be added to the cement and/or to the concrete that will be subject to a particularly aggressive chemical attack from those mentioned above, and in particular, to sulphates, chlorides or sea water. And for the sake of and justification of this need, it has to be said that the current Spanish Instruction for Structural Concrete EHE-08 does not provide any specification on "hydraulic factors" in general, nor the content of Al2O3r- (%) in fly ash, very particular, as Article 30º "Additions", or any other Article, although does provide, however, other chemical specifications lacking the necessary meaning in terms of the message Chemical Durability mentioned, nor the Article 37º which and for greater sake, is paradoxically entitled "Durability of the concrete and of their reinforcements". It has also not contemplated in the latest version just released from EN 197-1 standard entitled "Cement Part 1: Composition, specifications and conformity criteria for common cements". Nor, in EN 450-1:2006 entitled "Fly ash for concrete Part 1: Definitions, specifications and conformity criteria", nor by current Spanish Instruction for Cement Reception, RC-08, nor the ASTM C618-03 Standard either. The only chemical specification that both Standards, European and American, refer is one that says that the sum of the total contents of SiO2 (%), Al2O3 (%) and Fe2O3 (%) of natural and artificial pozzolan, must be greater than or equal to 70 % , defining pozzolans thus: "siliceous or aluminous and siliceous materials, which themselves do not have any cementitious value but finely divided and in the presence of moisture it reacts with calcium hydroxide at ordinary temperatures to form compounds possessing cementitious properties". Consequently and according to everything related before, the primary objective of this Doctoral Thesis has been: To design and start-up a new quantitative analytical method of technical utility (the maximum test duration is not more than 28 days), to determine the content of reactive alumina content, Al2O3r- (%), vitreous or amorphous alumina, of natural and artificial pozzolans. And once designed, validate at repeatability level and in accordance with appropriate statistical parameters with special emphasis on the acceptance criteria established by the American Association of Official Analytical Chemists (AOAC). And to achieve this, the innovation of this research has been based on the following general principles, namely: - All the alumina in any pozzolan, natural or artificial, that can be attacked, dissolved and leached by portlandite or calcium hydroxide, Ca(OH)2, in aqueous medium, is considered reactive alumina, Al2O3r-. - This aluminic fraction of natural or artificial pozzolan to analyze and study, has to be in such physical-chemical state that it can react in the presence of calcium hydroxide, sodium chloride and water status and to cause monochloro-aluminate hydrated calcium, C3A·CaCl2·10H2O or Friedel's salt. Moreover, such physical-chemical state of the pozzolan must be consistent with the definition of reactive alumina adopted in this research because of the actual performance of chemical durability that can reach confer on blended cements and their derivatives, concretes, mortars and pastes that are manufactured with the same. - The originality of this new analytical method, compared to the other methods for determining reactive alumina existing (collected in abbreviated form in the state of the art of this report), is the quantification of such aluminic fraction of natural or artificial pozzolans is performed by stoichiometric calculation based on this, in the chemical reaction of Friedel's salt formation after 28 days of the analysis of saline-basic hydration accelerated natural or artificial pozzolan also performed in this research, and the quantitative determination of the Friedel's salt has been performed by two instrumental analytical techniques known as thermogravimetric analysis (variant I), and Rietveld method with X-ray powder diffraction (variant II). - The chemical reaction of Friedel's salt formation after 28 days of accelerated saline-basic hydration of the selected natural and artificial pozzolan, was optimized to ensure that the single chemical compound of aluminium and chlorine formed was Friedel's salt only (dosing for this purpose in amount suitable chemical reagents: Ca(OH)2, NaCl and distilled water), and, on the other hand, maintaining the appropriate compromise between the highest yield from the chemical reaction (attack, dissolution and leaching in 28 days, all reactive alumina of pozzolan) and to accelerate the etching media, which were 40°C temperature, constant stirring and sealing the reactor. - The applicability and selectivity of the new analytical method, the subject of this Doctoral Thesis, was studied with a series of Spanish natural and artificial pozzolans, siliceous or siliceous and aluminous in nature, which were as follows: M0 (metakaolin 0), M1 (M0 with 50 % quartz), L and C (natural pozzolans of the Canary Islands), CV10 (fly ash 10), CV17 (fly ash 17), A (natural pozzolan of Almagro), O (natural pozzolan of Olot), and HS (silica fume). - All mineral admixtures were selected satisfied the physical and chemical requirements proposed to consider them as pozzolan, which was mandatory, so its Al2O3r- (%) content can determine by the new analytical method. These conditions were as follows: adequate degree of fineness of grind or average particle size (according to EN 451-2 standard), have been analyzed chemically (according to EN 196-2 or ASTM C311 standards), in order to determine their total contents of SiO2 (%), Al2O3 (%) and Fe2O3 (%), mainly, having also determined its reactive silica content, SiO2r- (%) (UNE 80225 standard), and fulfilled with testing of pozzolanicity or Frattini test (according to EN 196-5 standard) at 28 days age at least. The last criteria was mandatory until 1988, for any natural and artificial pozzolan to a factory intended to introduce cements in the manufacturing process of a new Portland cement type CEM IV pozzolanic additions, and with this Doctoral Thesis has made is to be used once again mandatory. And the results obtained using the new analytical method, of the Al2O3r- (%) content for each selected pozzolan, were as follows: - by its variant I: M0 29.9 % , M1 16.9 % , CV10 11.4 % , L 12.3 % , C 12.6 % , A 8.0 % , CV17 9.5 % and O 6.3 % of Al2O3r-, and - by its variant II: M0 30.7 % , M1 15.4 % , CV10 14.7% % , L 11.8 % , C 11.1 % , A 8.9 % , CV17 9.6 % and O 6.8 % of Al2O3r-. Finally, they would all be further contrasted by the calibration and validation of new analytical method, with reference values obtained from these same natural and artificial pozzolans, which had been given by the method of Florentin, consisting of attack, dissolve and leached with a basic attack (with Ca(OH)2 in aqueous medium and laboratory temperature, having also been its duration up to 1 year), followed by another acid attack (HCl, d = 1.12), all soluble aluminic fraction of pozzolan, and in particular their total content of reactive alumina, Al2O3r-(%), was this time as follows: M0 28.8 %, M1 16.7 %, CV10 9.7 %, L 11.2 %, C 12.2 %, A 13.0 %, CV17 10.6 % and O 9.5 % (and their siliceous and iron contents that are at par). This validation has shown on the new analytical method is more reliable than Florentin method, so it turns out to be entirely appropriate to get the results that have been tried by the same, besides providing them a relatively short space of time (28 days at most) and reasonably no high economic cost (unless mistake -free direct and indirect taxes, such economic cost would be between 800.00 - 900.00 €/pozzolan (most likely case), and about an one-third part around, in the event that the maximum age of the accelerated test is 7 days only (less likely case). So it is technically acceptable, to consider the range of possible variability of concentrations or contents pozzolan analyte with validation parameters such as: linearity (the results obtained are directly proportional to the instrumental response signal received), excellent sensitivity and accuracy, satisfactory repeatability values from the contents of each and Al2O3r- (%) each selected pozzolan, confirming therefore universal use. Finally, the advantages of the new analytical method over existing methods compiled from literature (Florentin method , the Lopez Ruiz method -HF and HNO3 40 % 2N-, the method of Murat and Driouche for clays -0.5M HF-, the method of Arjuan, Roy and Silbee for fly ash -HF 1 %- and its modification by Fernández-Jiménez et al -HF 1 %, 27Al MAS NMR and XRD (Rietveld method)-, and the method for determining the SiO2r-/Al2O3r- clay and fly ash ratio of Santaquiteria Ruiz et al -HF 1 %, NaOH 8M and ICP-AES-) are primarily and relatively short time get the result intended answer (28 days at most), its considerable lower cost, free from danger to the life safety of the people who need to manipulate and put in practice as well as its universality and selectivity, since it is applicable for all types of natural or artificial pozzolans, as it has been shown by the results of selected natural and artificial pozzolanic materials and analyzed in a range of analyte concentrations -reactive alumina, Al2O3r- (%) content- from 5 % to 30 % by mass, this range, on the other hand, includes virtually ALL existing transnational market in natural and artificial pozzolans and still exist. Therefore and in accordance with the above, the new analytical method is already performed by the variant I or II, because, - firstly, grounded to experimental approaches concerning its experimental procedure -"modus operandi"- which has been applied to a wide range of natural and artificial pozzolans, and - secondly, due to the quality of the results obtained with a great degree of accuracy and repeatability, it has been shown to possess significant scientific value in the research, but especially technical value -for quality control of natural and artificial pozzolans commonly added to Portland cement factory and/or directly to their concrete and mortar in plant-, and also be representative enough of the values obtained by the same probable chemical durability that each of them can reach out to give the concrete mortar and paste to which it belongs, as well as proper amount of partial replacement of Portland cement. To get in line with their own chemical-physical or physical-chemical features which can come to confer, as its chemical character (aluminic, silicic-aluminic, aluminic-silicic, aluminic-ferric-silicic or ferric-silicic), form and medium size of its particle is. Finally, the new analytical method has proven to meet all mandatory requirements established by ISO/IEC 17025 on the quality and reliability of new methods or analytical procedures are not standardized yet, in order to be considered appropriate this new analytical method, in this Doctoral Thesis it is to be proposed in the near future, before the corresponding AENOR (Spanish Association for Standardization and Certification) Commission, to start a procedure for certification and standardization.

Prototype of EN 301 549 Decision tree

The new European Standard EN 301 549 “Accessibility requirements suitable for public procurement of ICT products and services in Europe” is the response by CEN, CENELEC and ETSI to the European Commission’s Mandate 376. Today, ICT products and services are converging, and the boundaries between product categories are being constantly blurred. For that reason EN 301 549 has been drafted using a feature-based approach, instead of being based on product categories. The result is a standard that can be applied to any ICT product and service, by identifying applicable requirements depending on the features of the ICT. This demonstration presents ongoing work at the research group CETTICO of the Technical University of Madrid. CETTICO is developing a workgroup-based support tool where teams of people can annotate the result of performing a conformity assessment of a given ICT product or service according to the requirements of the EN. One of the functions of the tool is creating evaluation projects. During that task the user defines the features of the corresponding ICT product or service by answering questions presented by the tool. As a result of this process, the tool will create a list of applicable requirements and recommendations.

Modelo del sistema de gestión de la calidad y el desempeño organizacional en la producción de petróleo

El proceso de cambio de una sociedad industrial a una sociedad del conocimiento, que experimenta el mundo globalizado en el siglo XXI, induce a las empresas y organizaciones a desarrollar ventajas competitivas y sostenibles basadas en sus activos intangibles, entre los cuales destacan los sistemas de gestión en general y los sistemas de gestión de la calidad (SGC) en particular. Las organizaciones dedicadas a la producción de petróleo están influenciadas por dicha tendencia. El petróleo es un recurso natural con reservas limitadas, cuya producción y consumo ha crecido progresivamente, aportando la mayor cuota (35 %) del total de la energía que se consume en el mundo contemporáneo, aporte que se mantendrá hasta el año 2035, según las previsiones más conservadoras. Por tanto, se hace necesario desarrollar modelos de producción innovadores, que contribuyan a la mejora del factor de recobro de los yacimientos y de la vida útil de los mismos, al tiempo que satisfagan los requerimientos de producción y consumo diarios de los exigentes mercados globales. El objeto de esta investigación es el desarrollo de un modelo de gestión de la calidad y su efecto en el desempeño organizacional, a través del efecto mediador de los constructos satisfacción del cliente interno y gestión del conocimiento en la producción de petróleo. Esta investigación de carácter explicativo, no experimental, transeccional y ex-postfacto, se realizó en la región petrolífera del lago de Maracaibo, al occidente de Venezuela, la cual tiene más de 70 años en producción y cuenta con yacimientos maduros. La población objeto de estudio fue de 369 trabajadores petroleros, quienes participaron en las mesas técnicas de la calidad, durante los meses de mayo y julio del año 2012, los cuales en su mayoría están en proceso de formación como analistas, asesores y auditores de los SGC. La técnica de muestreo aplicada fue de tipo aleatorio simple, con una muestra de 252 individuos. A la misma se le aplicó un cuestionario diseñado ad hoc, el cual fue validado por las técnicas de juicio de expertos y prueba piloto. El procedimiento de investigación se realizó a través de una secuencia, que incluyó la elaboración de un modelo teórico, basado en la revisión del estado del arte; un modelo factorial, sobre la base del análisis factorial de los datos de la encuesta; un modelo de regresión lineal, elaborado a través del método de regresión lineal simple y múltiple; un modelo de análisis de sendero, realizado con el software Amos 20 SPSS y finalmente, un modelo informático, realizado con el simulador Vensim PLE v.6.2. Los resultados obtenidos indican que el modelo teórico se transformó en un modelo empírico, en el cual, la variable independiente fue el SGC, la variable mediadora fue la integración de las dimensiones eliminación de la no conformidad, satisfacción del cliente interno y aprendizaje organizacional (ENCSCIAO) y la variable respuesta la integración de las dimensiones desempeño organizacional y aprendizaje organizacional (DOOA). Se verificó el efecto mediador del ENSCIAO sobre la relación SGC-DOOA con una bondad del ajuste, del 42,65%. En el modelo de regresión múltiple se encontró que las variables determinantes son eliminación de la no conformidad (ENC), conocimiento adquirido (CA) y conocimiento espontáneo (CE), lo cual fue corroborado con el modelo de análisis de sendero. El modelo informático se desarrolló empleando datos aproximados de una unidad de producción tipo, generándose cuatro escenarios; siendo el más favorable, aquel en el cual se aplicaba el SGC y variables relacionadas, reduciendo la desviación de la producción, incrementando el factor de recobro y ampliando la vida útil del yacimiento. Se concluye que la aplicación del SGC y constructos relacionados favorece el desempeño y la producción de las unidades de explotación de yacimientos petrolíferos maduros. Los principales aportes de la tesis son la obtención de un modelo de gestión de la producción de petróleo en yacimientos maduros, basado en los SGC. Asimismo, el desarrollo de un concepto de gestión de la calidad asociado a la reducción de la desviación de la producción petrolífera anual, al incremento del factor de recobro y al aumento de la vida útil del yacimiento. Las futuras líneas de investigación están orientadas a la aplicación del modelo en contextos reales y específicos, para medir su impacto y realizar los ajustes pertinentes. ABSTRACT The process of change from an industrial society to a knowledge-based society, which undergoes the globalized world in the twenty-first century, induces companies and organizations to develop a sustainable and competitive advantages based on its intangible assets, among which are noteworthy the management systems in general and particularly the quality management systems (QMS). Organizations engaged in oil production are influenced by said trend. Oil is a natural resource with limited reserves, where production and consumption has grown progressively, providing the largest share (35%) of the total energy consumed in the contemporary world, a contribution that will remain until the year 2035 according to the more conservative trust estimations. Therefore, it becomes necessary to develop innovative production models which contribute with the improvement of reservoirs´ recovery factor and the lifetime thereof, while meeting the production requirements and daily consumption of demanding global markets. The aim of this research is to develop a model of quality management and its effect on organizational performance through the mediator effect of the constructs, internal customer satisfaction and knowledge management in oil production. This research of explanatory nature, not experimental, transactional and expos-facto was carried out in the oil-region of Maracaibo Lake located to the west of Venezuela, which has more than 70 years in continuous production and has mature reservoirs. The population under study was 369 oil workers who participated in the technical quality workshops, during the months of May and July of 2012, the majority of which were in the process of training as analysts, consultants and auditors of the QMS. The sampling technique applied was simple random type. To a sample of 252 individuals of the population it was applied an ad hoc designed questionnaire, which was validated by the techniques of expert judgment and pilot test. The research procedure was performed through a sequence, which included the elaboration of a theoretical model, based on the review of the state of the art; a factorial model with based on factorial analysis of the survey data; a linear regression model, developed through the method of simple and multiple linear regression; a structural equation model, made with software °Amos 20 SPSS° and finally, a computer model, performed with the simulator Vensim PLE v.6.2. The results indicate that the theoretical model was transformed into an empirical model, in which the independent variable was the QMS, the mediator variable was the integration of the dimensions: elimination of non-conformity, internal customer satisfaction and organizational learning (ENCSCIAO) and the response variable the integration of the dimensions, organizational performance and learning organizational (DOOA). ENSCIAO´s mediator effect on the relation QMS-DOOA was verified with a goodness of fit of 42,65%. In the multiple regression model was found to be the determining variables are elimination of nonconformity (ENC), knowledge acquired (CA) and spontaneous knowledge (EC), which was verified with the structural equation model. The computer model was developed based on approximate data of an oil production unit type, creating four (04) scenarios; being the most favorable, that one which it was applied the QMS and related variables, reducing the production deviation, increasing the recovery factor and extending the lifetime of the reservoir. It is concluded that QMS implementation powered with the related constructs, favors performance and production of mature oilfield of exploitation reservoirs units. The main contributions of this thesis are obtaining a management model for oil production in mature oilfields, based on QMS. In addition, development of a concept of quality associated to reduce the annual oil production deviation, increase the recovery factor and increase oilfield lifetime. Future lines of research are oriented to the implementation of this model in real and specific contexts to measure its impact and make the necessary adjustments that might take place.

Materialidad poética: arquitectura suiza en el entorno de los Grisones 1992-2004

El entorno alpino de los Grisones ha sido un laboratorio donde experimentar un método arquitectónico procedente de diversas fuentes durante los años 70 en la ETHZ. Este método ha producido durante las últimas tres décadas un discurso teórico propiamente suizo alemán. La tradición continúa siendo un valor cultural para la comunidad alpina de los Grisones, que apuesta por seguir relacionando la arquitectura con su historia y su paisaje. La especificidad de cada entorno suizo alemán es un hecho obvio pero, por encima de sus rasgos característicos, hay un denominador común que les da unidad en silencio: se trata de una idea de la construcción. El fenómeno de los Grisones es territorial en su localización concreta, pero comparte el trasfondo teórico del resto de la arquitectura suizo alemana reciente. La tesis recorre transversalmente las condiciones que han dado lugar a esa trayectoria común hasta la actualidad, en que la arquitectura suizo alemana se halla precisamente en un momento de cambio generacional. La obra de Peter Märkli constituye en esta tesis un paradigma de la voluntad suizo alemana por formar parte de la continuidad cultural de la arquitectura, como una actitud de resistencia compartida frente al mundo globalizado. La tesis se articula a partir de ocho proyectos recientes, realizados por arquitectos suizo alemanes en el entorno del territorio alpino de los Grisones. Estos proyectos condensan la trayectoria arquitectónica suizo alemana durante el siglo XX, así como el fenómeno arquitectónico que ha tenido lugar en el entorno de los Grisones durante las últimas tres décadas. La tesis analiza a través de cada pareja de proyectos los episodios teóricos, artísticos y filosóficos más relevantes que se sintetizan en estas obras, así como sus referentes arquitectónicos y la dimensión trascendente de los materiales en los que la cultura suiza hunde sus raíces: la madera, la piedra y el hormigón. Las vanguardias pictóricas, el Movimiento Moderno y las corrientes humanistas y regionalistas que se fueron sucediendo durante el pasado siglo, configuran el escenario en el que tomó cuerpo la sensibilidad arquitectónica suizo alemana reciente, que emerge a través de la compleja red de relaciones establecidas entre el panorama suizo y el internacional. El mismo bagaje teórico subyace al territorio suizo alemán a nivel general, por lo que asociarlo a través de esta tesis a proyectos realizados en un entorno característico, permite acceder a una realización concreta de ese debate en un entorno tan particular como son los Grisones. La aproximación a los proyectos es de carácter fenomenológico: la experiencia directa de los mismos ha sido el sustrato fundamental del enfoque de la tesis. El trabajo de campo no se limitó a visitar los proyectos que vertebran la tesis, sino que trató de abarcar las obras más relevantes de la producción suizo alemana reciente en los Grisones, con el fin de adquirir cierto grado de sensibilidad perceptiva hacia la singularidad de su identidad territorial. La tesis hace especial hincapié en las obras de Peter Märkli y Peter Zumthor, representantes de los dos extremos del discurso suizo alemán reciente, respecto a la materialidad y al carácter de la secuencia espacial, sistemático o fluido respectivamente, pero que asimismo comparten el clasicismo formalista que subyace al fenómeno suizo alemán. Los dos proyectos que establecen el periodo 1992-2004 explorado por esta investigación constituyen dos hitos fundamentales. El Museo de La Congiunta en Giornico de Peter Märkli se construyó en 1992 y se erige a partir de entonces como un icono arquitectónico de la condensación típicamente suizo alemana de base reductiva. Este paradigma de síntesis conceptual y constructiva comenzó a forjarse en la década de 1930 de la mano del Konkrete Kunst formulado por Max Bill, que es la única manifestación artística genuinamente suiza del siglo XX y que desarrolló pictóricamente los valores de precisión, rigor, racionalismo y abstracción afines a la sensibilidad suizo alemana. En segundo lugar, el proyecto para la rehabilitación de la Villa Garbald y la construcción de la Torre Roccolo en Castasegna llevado a cabo por Miller & Maranta en 2004, supuso la consumación de la Analoge Architektur, que fue la primera corriente arquitectónica propiamente suiza, desarrollada durante la década de 1980 por Miroslav Sik. La Deutscher Tendenza es un periodo de la trayectoria suizo alemana reciente poco conocido, representado por una figura tan relevante como es Peter Zumthor. Las obras que proyectó Zumthor entre 1979 y 1985 forman parte de un periodo en que el arquitecto se encontraba profundamente influido por el neorracionalismo italiano, como ilustra la escuela de Churwalden de 1983. La arquitectura suizo alemana reciente exploró sistemáticamente los sistemas compositivos de las vanguardias pictóricas y del Movimiento Moderno, por encima de su formalismo concreto. La segunda fase de la obra de Zumthor entre 1985 y 1996 se caracteriza por la transfiguración del plano libre del sistema compositivo neoplasticista desarrollado por De Stijl, plano que adquirió grosor hasta convertirse en la caja articuladora de la fluidez de la secuencia espacial. El formalismo de Zumthor en esta fase implica la prioridad del esquema compositivo, compuesto por un perímetro regular en el que se reúnen las cajas que, como las superficies de color de las composiciones de Mondrian, articulan el espacio a su alrededor. La Residencia de Masans de Zumthor de 1993 es un proyecto canónico de este sistema compositivo, que culmina en el esquema radial de las Termas de Vals de 1996. La imagen poética se convirtió en el lenguaje propio del pensamiento de la arquitectura suizo alemana, que permitía una reflexión no verbal, a partir de unos pocos arquetipos fundamentales. Los arquitectos del Ticino buscaron en la Tendenza italiana durante la década de 1970 una alternativa al insostenible modelo territorial que estaba destruyendo su paisaje cultural. Algunos de estos arquitectos comenzaron a dar clase durante esa década en la ETHZ, por lo que transmitieron sus inquietudes al alumnado e introdujeron a Aldo Rossi en la facultad, que era uno de los máximos representantes de la Tendenza. El método analógico de Rossi, basado en la psicología analítica de Carl Jung, fue una influencia fundamental en la ETHZ durante los años 70. Rossi partía de una teoría afín al colectivo intelectual suizo que los arquitectos de la ETHZ pronto comprendieron que debían independizar del contexto italiano, desarrollando su propio método a partir de 1985 con la Analoge Architektur. El valor de la preexistencia de acuerdo a este método incipiente se hallaba en su papel articulador de la continuidad cultural de una comunidad, que Miroslav Sik definió a partir de su concepto de Altneue (literalmente, lo Nuevo-Viejo). La fusión entre lo nuevo y lo viejo era la base de la espontaneidad con la que habían crecido los asentamientos históricamente. Sik consideraba que la continuidad dependía de la comprensión de los patrones preexistentes, con el objeto de mantener su vigencia mediante la incorporación de estrategias contemporáneas, que renovarían su significado sin perder su esencia. La Casa Gugalun en Versam de Zumthor de 1994 supone una aproximación a escala doméstica a este planteamiento. La arquitectura suizo alemana reciente a menudo busca en sus referentes plásticos una manera de explorar ámbitos poco accesibles para la disciplina arquitectónica. El pensamiento arquitectónico basado en la imagen poética se implementa a partir de la tectónica de la construcción, que es el medio para comunicar una idea vertebradora del proyecto de principio a fin. La construcción como medio introduce el concepto clave de la apariencia de la arquitectura, estrechamente relacionado con la filosofía idealista de Friedrich Schiller. La apariencia debe expresar el sentido conceptual de la obra, que los arquitectos suizo alemanes denominan idea, por lo que la construcción no tiene un valor por sí misma, sino en cuanto a la apariencia. La Capilla de Oberrealta de Christian Kerez de 1993 puede ser considerada una obra escultórica en el paisaje, más próxima a las artes plásticas que a la arquitectura. La tensión que surge entre la figura ideal y la pieza sometida a una sutil deformación confiere un carácter dinámico a la composición, que intensifica el efecto perceptivo, de acuerdo a la teoría del pensamiento visual de Rudolph Arnheim. La deformación al servicio de la psicología de la percepción es un fenómeno que caracteriza la arquitectura suizo alemana reciente. El concepto de Forme Forte (forma fuerte) fue introducido por Martin Steinmann para caracterizar el objeto arquitectónico denominado internacionalmente Swiss Box. Este concepto se caracteriza por una predilección por lo monolítico, lo unitario y lo arquetípico. La condición más sustancial de una Forme Forte es, sin embargo, la de configurar un elemento estructurador del entorno. Tanto la base morfológica de una Forme Forte, como su capacidad para estructurar el lugar, se corresponden con los conceptos de arquetipo y monumento de la teoría de Rossi. La tesis explora el sentido de la deformación en la producción suizo alemana reciente, a partir de la Escuela de Paspels de Valerio Olgiati de 1998 y la Torre Roccolo de Villa Garbald de Miller&Maranta de 1998. La teoría tectónica de Gottfried Semper y la razón de la forma de Adolf Loos constituyen el sustrato teórico, que relaciona la actividad existencial de habitar con la materialidad de la arquitectura suizo alemana reciente. La teoría tectónica de Semper fundamenta las revisiones posteriores de los sistemas constructivos tradicionales suizo alemanes. Esta influencia sirvió como base a la vanguardia suiza de la Neues Bauen, que desarrolló un racionalismo funcionalista durante las décadas de 1920 y 1930, que constituye una gramática de base no simbólica. Esta gramática constituye el fundamento de la transición del orden clásico a la materialidad como instrumento compositivo durante la segunda mitad del siglo XX, consolidando el concepto de la base material de la forma. La revisión de la tradición regionalista y racionalista llevada a cabo por la generación de arquitectos suizo alemanes de la década de 1950 y 1960, constituyó una investigación lingüística sustancial. Rudolph Olgiati es la figura determinante de este periodo. La revisión de esta investigación se codificó en clave estructuralista durante los años 70 en la ETHZ, influenciada por la presencia de Roland Barthes como profesor invitado. Esta revisión constituyó la base de la articulación tectónica propiamente suizo alemana todavía vigente, como ilustra expresamente la obra de Burkhalter&Sumi en esta tesis. La obra de Gion Caminada en Vrin entre 1995 y 2002 aporta una intensa investigación sobre el Strickbau, que implementa una y otra vez variaciones sobre un sistema tradicional, ilustrando las infinitas posibilidades que ofrece un lenguaje, paradójicamente limitado por los medios disponibles en un entorno alpino aislado. Para terminar Jürg Conzett es el ingeniero con el que han desarrollado sus proyectos la mayoría de los arquitectos en el entorno de los Grisones, formado durante 8 años con Zumthor y colaborador habitual de Caminada entre otros. Conzett es el referente que relaciona la ingeniería con la arquitectura en el ámbito de esta tesis, imprescindible en el contexto de esta investigación. ABSTRACT The Alpine setting of Grisons has been a laboratory for architectural experimentation with an approach forged in the 1970s from various sources in the Swiss Federal Institute of Technology in Zurich (ETHZ). This method has produced a uniquely German-Swiss theoretical discourse over the past three decades. Tradition continues to be a cultural value for Grisons, a region committed to continue linking its architecture with the region’s history and landscape. The specificity of the German-Swiss environment is obvious, but beyond its characteristic features, there is a common denominator that gives these settings a silent unity: it is an idea of building. The phenomenon of Grisons is geographic in its specific location, but it shares the theoretical basis of the rest of the new German-Swiss architecture. This thesis transversely delves into the conditions that have shaped this common path up to the present, just as German-Swiss architecture is going through a time of generational change. In this thesis, Märkli Peter's work constitutes a paradigm of the German-Swiss will to uphold the cultural and architectural continuity of the region, exemplifying an attitude of shared resistance to the globalized world. The thesis is structured around eight recent projects carried out by German-Swiss architects in the Alpine region of Grisons. These projects represent the trajectory of twentieth century German-Swiss architectural history, as well as the architectural phenomenon that has taken place in the environs of Grisons over the past three decades. Through these projects the thesis analyzes the most relevant theoretical, artistic and philosophical references that are synthesized in the works, as well as their architectural references and the transcendental dimension of the materials in which Swiss culture is rooted: wood, stone and concrete. The artistic avant-garde, together with Modernism and the humanistic and regional movements that occurred during the last century, set the stage for present-day German-Swiss architectural sensitivity, which emerges from a complex web of relationships established between the Swiss and international panorama. This same theoretical background and experience underlies all of the German-Swiss territory in general, so associating it through this thesis to a particular context allows the description of a specific embodiment of this debate, within the unique environment of Grisons. The methodological approach to analyzing the projects was phenomenological: direct experience is the main substrate underpinning the focus of the thesis. Field work was not limited to visiting the projects featured in the thesis, but rather encompassed the most important works of recent German-Swiss construction in the Grisons in order to gain some degree of perceptual sensitivity to the uniqueness of its territorial identity. The present paper puts special emphasis on the works of Peter Märkli and Peter Zumthor, who share the formal classicist perspective of the German-Swiss context but stand on opposite sides of the philosophical spectrum with regard to the notion of materiality and the nature of space, which they conceive as systematic or fluid, respectively. The two projects that establish the boundaries of the time period 1992–2004 explored by this research represent two key milestones. The Museum La Congiunta in Giornico, by Peter Märkli, was built in 1992 and quickly established itself as an architectural icon of German-Swiss reductionism. This paradigm of conceptual and constructive synthesis began to take shape in the 1930s under the banner of Konkrete Kunst (Concrete Art), led by Max Bill. The only genuinely Swiss artistic movement of the twentieth century, Konkrete Kunst was characterized by the artistic values of precision, rigor, rationalism and abstraction, sentiments that were very close to the German-Swiss tradition. Secondly, the project for the rehabilitation of Villa Garbald and the construction of the Roccolo Tower in Castasegna, conducted by Miller&Maranta in 2004, represented the consummation of the Analoge Architektur, which was the first truly Swiss architectural movement, spearheaded in the 1980s by Miroslav Sik. The Deutscher Tendenza is a little-known period of recent German-Swiss history, represented by the important figure of Peter Zumthor. The projects that Zumthor led between 1979 and 1985 are part of a period when Italian Neo-Rationalism exercised a profound influence on the architect, as illustrated by the Churwalden School, circa 1983. Recent German-Swiss architecture systematically explored the compositional systems of the artistic avant-garde and Modernism, beyond its specific formal aspects. The second phase of Zumthor's work, between 1985 and 1996, is characterized by the transfiguration of the free plane, neoplastic compositional system developed by De Stijl, a plane that thickened until it became the box articulating fluidity from the spatial sequence. Zumthor's formalism in this phase prioritizes the compositional scheme, consisting of a regular perimeter in which the boxes that -like Mondrian’s colored surfaces- arrange the space around it. Zumthor’s Masans Residence, circa 1993, is a canonical project of this compositional system, which culminates in the radial pattern of the Therme Vals, circa 1996. The poetic image became the appropriate language of thought for German-Swiss architecture, which invited a nonverbal reflection inspired by a few fundamental archetypes. The architects of Ticino sought, through the Italian Tendenza of the 1970s, an alternative to the unsustainable territorial model that was destroying their cultural landscape. Some of these architects began to teach during that decade at ETHZ, and naturally they transmitted their unease to their students. These architects also introduced Aldo Rossi, one of the leading representatives of the Tendenza, to the school. Rossi’s analogue method, based on the analytical psychology of Carl Jung, was a major influence on the ETHZ during the 1970s. Rossi’s theoretical grounding was very much in tune with Swiss intellectualism, and it did not take long for architects from ETHZ to realize that they should break away from the Italian context, developing their own method from 1985 on with the Analoge Architektur. The value of the pre-existing conformity of this emerging method, stemmed from its role in facilitating the cultural continuity of a community, which Miroslav Sik defined in his concept of Altneue (literally, Old-new). This fusion of old and new was the basis for the spontaneity with which settlements had historically grown. Sik considered that continuity depended on understanding the existing patterns and sustaining their relevance through the incorporation of contemporary strategies, which would renew their meaning without losing their essence. Zumthor’s Gugalun House in Versam, circa 1994, is a domestic-scale approach to this philosophy. Modern German-Swiss architecture often looks to its references in visual art for a way to explore areas that are normally inaccessible to the architectural discipline. Architectural thinking based on the poetic image is achieved through a building’s tectonics, which communicate the core idea of a project from start to finish. The understanding of construction as a medium introduces the key concept of the appearance in architecture, closely related to the idealistic philosophy of Friedrich Schiller. The appearance should express the conceptual meaning of the work, which German-Swiss architects call the idea, so that the building does not have value in and of itself, but only in terms of its appearance. The Oberrealta Chapel by Christian Kerez, circa 1993, can be considered a sculpture in the landscape, closer to the visual arts than to architecture. The tension that arises between the ideal figure and the piece subjected to a subtle deformation confers a dynamic character onto the composition, intensifying the perceptual effect, according to Rudolf Arnheim’s theory of visual thought. The deformation in the service of the psychology of perception is a phenomenon that characterizes recent German-Swiss architecture. Martin Steinmann introduced the Forme Forte (Strong Form) concept to describe the architectural object known internationally as the Swiss Box. This concept is characterized by a predilection for all things monolithic, unitary and archetypal. The most substantial condition of a Forme Forte, however, is the configuration of a structuring element in the environment. Both the morphological basis of a Forme Forte and its ability to frame the place, correspond to the concepts of archetype and monument put forward by Rossi’s theory. The present thesis explores the sense of deformation in recent German-Swiss production, based on the School of Paspels by Valerio Olgiati, circa 1998 and the Roccolo Tower in Villa Garbald, by Miller&Maranta, circa 1998. Gottfried Semper’s tectonic theory and Adolf Loos’s reason for form constitute the theoretical foundation that links the existential activity of dwelling to the materiality of recent German-Swiss architecture. Semper’s tectonic theory laid the foundation for subsequent revisions of the German-Swiss traditional building systems. This influence was the basis for the Swiss avant-garde of Neues Bauen, which developed a functional rationalism during the 1920s and 30s that served as a non-symbolic grammatical foundation for the transition from classical order to materiality as a compositional tool. During the second half of the twentieth century, this architectural grammar helped consolidate the concept of the material base of the form. The revision of the regionalist and rationalist tradition, carried out by the generation of German-Swiss architects of the 1950s and 60s, constituted a substantial linguistic investigation. Rudolph Olgiati is the key figure of this period. The research was codified in terms of structuralism in the 1970s in ETHZ and influenced by the presence of Roland Barthes as a visiting professor. This revision was the basis of the uniquely German-Swiss tectonic design still in use today, as specifically illustrated by the work of Burkhalter & Sumi in this thesis. Gion Caminada's work in Vrin between 1995 and 2002 offers an extensive study on the Strickbau, which implements variations on a traditional system again and again, illustrating the endless possibilities of a language that paradoxically seems limited by the available resources in a remote Alpine setting. Finally, Jürg Conzett is the engineer with whom most architects in the Grisons region have developed their projects. Trained under Zumthor for 8 years, and a regular collaborator of Caminada, among others, Conzett is the reference point linking engineering with architecture in this thesis, essential in the context of this research.