Selective oxidation of m-phenoxytoluene to m-phenoxybenzaldehyde with methanol as an additive in acetic acid

With addition of methanol in acetic acid solvent, m-phenoxytoluene could be oxidized to m-phenoxybenzaldehyde selectively by a cobalt bromide catalyst. Paratemters such as the ratio of Co/Br and the reaction time of m-phenoxytoluene oxidation as well as visible spectra of cobalt bromide in acetic acid/methanol solvents, were also investigated. Addition of methanol caused the oxidation of aldehydes to proceed more slowly than it did solely in acetic acid solvent. The decrease of cobaltous-multibromides in acetic acid/methanol solvents was responsible for the improvement in the selective oxidation of m-phenoxytoluene. (C) 1999 Elsevier Science B.V. All rights reserved.

The active sites in different TS-1 zeolites for propylene epoxidation studied by ultraviolet resonance Raman and ultraviolet visible absorption spectroscopies

The titanium species in four kinds of titanium-containing MFI zeolites have been studied by ultraviolet (UV)-Raman and ultraviolet visible (UV-Vis) absorption spectroscopies and by the epoxidation of propylene with diluted H2O2 solution (30%). UV-Raman spectroscopy is proved to be a suitable means to estimate qualitatively the framework titanium in TS-l zeolites. Based on the comparison of the relative intensity ratio I-1125/I-380 of UV-Raman spectra, the TS-1(conv.) sample synthesized hydrothermally by the conventional procedure shows the highest amount of framework titanium. UV-Vis spectroscopy reveals that besides minor anatase. titanium species are mainly tetrahydrally coordinated into the framework for TS-l(conv.) or the Ti-ZSM-5 sample prepared by gas-solid reaction between deboronated B-ZSM-5 and TiCl4 vapor at elevated temperatures. For the TS-1(org.) and TS-1(inorg.) samples synthesized hydrothermally using tetrapropylammonium bromide (TPABr) as template and tetrabutylorthotitanite (TBOT) and TiCl3 as titanium source, respectively, the presence of mononuclear and isolated TiOx species which are proposed to bond to the zeolite extraframework is observed. In addition to the framework titanium species, these isolated TiOx species are assumed to be also active for propylene epoxidation.

Titanium species in titanium silicalite TS-1 prepared by hydrothermal method

The titanium species existing in titanium silicalite TS-1, which is prepared by hydrothermal method, were investigated using chemical analysis, XRD, FT-IR, Si-29 MAS NMR, UV-VIS, ESR. It has been observed that several kinds of titanium species may exist in titanium silicalite. The form that titanium atoms incorporate into the framework of titanium silicalite synthesized using tetrapropylammonium bromide (TPABr) as template differs from that using the classical method. But, the symmetry of titanium silicalite, changes from monoclinic to orthorhombic with the increase of titanium content in both methods. The Ti-O-2(-) originated from framework titanium and H2O2 has the moderate stability and may be active site in oxidation reaction. TS-1 synthesized using TPABr as template does not contain anatase, but contains a kind of partly condensed titanium species with six-fold coordination. The titanium species may correspond to 270-280 mn band in UV-VIS spectra and also can form Ti-O-2(-). But, this kind of Ti-O-2(-) is very stable and cannot be catalytic active site. So, the six-fold coordination titanium species may be inactive in both the oxidation reaction and the decomposition of H2O2. The hypothesis has been further proved by the phenomena that the titanium species is easily washed off using acid, and acid treating will not influence the catalytic performance of TS-1. (C) 2001 Elsevier Science B.V. All rights reserved.

A highly active palladium-phosphoramidite catalyst for the Suzuki cross-coupling of aryl bromides

A highly efficient palladium-catalyzed Suzuki coupling of aryl bromides with aiylboronic acids using phosphoramidite ligand 2c was developed. The phosphoramidite ligands are cost-effective and easily prepared from inexpensive, commercially available starting materials using a simple, efficient method. It represents an advance toward the discovery of low-cost catalyst systems for eventual availability. (c) 2005 Elsevier B.V. All rights reserved.

Nanotoxicologia

Projeto de Pós-Graduação/Dissertação apresentado à Universidade Fernando Pessoa como parte dos requisitos para obtenção do grau de Mestre em Ciências Farmacêuticas

Design, synthesis and evaluation of novel ellipticine derivatives and analogues as anti-cancer agents

This thesis describes work carried out on the synthesis of novel 5- and 11-substituted ellipticines and derivatives of the ellipticine analogues, isoellipticine and deazaellipticine, followed by investigation of their potential as anti-cancer agents. Preparation of the key 5- and 11-substituted ellipticine targets involved the development of regiospecific, sequential alkylation reactions with alkenyllithium and Grignard reagents. Investigation of these novel reactions resulted in a new route towards 5-substituted ellipticines via Grignard reaction with vinylmagnesium bromide. These novel 5-vinylellipticine derivatives were further functionalised in an ozonolysis reaction, followed by oxidation to give a range of novel 5-substituted ellipticines. Less success was encountered in the 11-substituted ellipticine series, however preparation of these derivatives using a previously published route was accomplished, and the resulting 11-formylellipticine was further derivatised to give a panel of novel 9- and 11-substituted ellipticines, incorporating amide, carboxylate, imine and amine functionality. The successful route towards 5-substituted ellipticines was applied to the preparation of a range of novel 11-substituted isoellipticines and 6-substituted deazaellipticines, the first time substantial synthesis has been undertaken with these analogues. In addition to this, the first preparation of isoellipticinium salts is described, and a panel of novel isoellipticinium, 7 formylisoellipticinium and 7-hydroxyisoellipticinium salts were synthesised in good yields. Biological evaluation of a panel of 43 novel ellipticine, isoellipticine and deazaellipticine derivatives was accomplished with a topoisomerase II decatenation assay and submission to the NCI 60-cell line screen. Four novel isoellipticine topoisomerase II inhibitors were identified from the decatenation assay, with strong activity at 10 μM. In addition to this, NCI screening identified five highly cytotoxic ellipticine and isoellipticine compounds with remarkable selectivity profiles for different cancer types. These novel lead compounds represent new templates for further research and synthesis.

Biological wastes as plant growth substrate amendments

Globally, agriculture is being intensified with mechanization and increased use of synthetic fertilizers and pesticides. There has been a scaling up of production to satisfy the demands of supermarket distribution. Problems associated with intensification of production, trade globalisation and a larger market demand for greater volumes of fresh produce, include consumers' concern about pesticide residues and leaching of nutrients and pesticides into the environment, as well as increases in the transmission of human food-poisoning pathogens on raw vegetables and in fruit juices. The first part of this research was concerned with the evaluation of a biological control strategy for soil-borne pathogens, these are difficult to eliminate and the chemicals of which the most effective fumigants e.g. methyl bromide, are being withdrawn form use. Chitin-containing crustaceans shellfish waste was investigated as a selective growth substrate amendment in the field, in glasshouse and in storage trials against Sclerotinia disease of Helianthus tuberosus, Phytophthora fragariae disease of Fragaria vesca and Fusarium disease of Dianthus. Results showed that addition to shellfish waste stimulated substrate microbial populations and lytic activity and induced plant defense proteins, namely chitinases and cellulases. Protective effects were seen in all crop models but the results indicate that further trials are required to confirm long-term efficacy. The second part of the research investigated the persistence of enteric bacteria in raw salad vegetables using model food poisoning isolates. In clinical investigations plants are sampled for bacterial contamination but no attempt is made to differentiate between epiphytes and endophytes. Results here indicate that the mode isolates persist endophytically thereby escaping conventional chlorine washes and they may also induce host defenses, which results in their suppression and in negative results in conventional plate count screening. Finally a discussion of criteria that should be considered for a HACCP plan for safe raw salad vegetable production is presented.

Development of a triple stage heat transformer for the recycling of low temperature heat energy

Absorption heat transformers are thermodynamic systems which are capable of recycling industrial waste heat energy by increasing its temperature. Triple stage heat transformers (TAHTs) can increase the temperature of this waste heat by up to approximately 145˚C. The principle factors influencing the thermodynamic performance of a TAHT and general points of operating optima were identified using a multivariate statistical analysis, prior to using heat exchange network modelling techniques to dissect the design of the TAHT and systematically reassemble it in order to minimise internal exergy destruction within the unit. This enabled first and second law efficiency improvements of up to 18.8% and 31.5% respectively to be achieved compared to conventional TAHT designs. The economic feasibility of such a thermodynamically optimised cycle was investigated by applying it to an oil refinery in Ireland, demonstrating that in general the capital cost of a TAHT makes it difficult to achieve acceptable rates of return. Decreasing the TAHT's capital cost may be achieved by redesigning its individual pieces of equipment and reducing their size. The potential benefits of using a bubble column absorber were therefore investigated in this thesis. An experimental bubble column was constructed and used to track the collapse of steam bubbles being absorbed into a hotter lithium bromide salt solution. Extremely high mass transfer coefficients of approximately 0.0012m/s were observed, showing significant improvements over previously investigated absorbers. Two separate models were developed, namely a combined heat and mass transfer model describing the rate of collapse of the bubbles, and a stochastic model describing the hydrodynamic motion of the collapsing vapour bubbles taking into consideration random fluctuations observed in the experimental data. Both models showed good agreement with the collected data, and demonstrated that the difference between the solution's temperature and its boiling temperature is the primary factor influencing the absorber's performance.

Impacts of shale gas wastewater disposal on water quality in western Pennsylvania.

The safe disposal of liquid wastes associated with oil and gas production in the United States is a major challenge given their large volumes and typically high levels of contaminants. In Pennsylvania, oil and gas wastewater is sometimes treated at brine treatment facilities and discharged to local streams. This study examined the water quality and isotopic compositions of discharged effluents, surface waters, and stream sediments associated with a treatment facility site in western Pennsylvania. The elevated levels of chloride and bromide, combined with the strontium, radium, oxygen, and hydrogen isotopic compositions of the effluents reflect the composition of Marcellus Shale produced waters. The discharge of the effluent from the treatment facility increased downstream concentrations of chloride and bromide above background levels. Barium and radium were substantially (>90%) reduced in the treated effluents compared to concentrations in Marcellus Shale produced waters. Nonetheless, (226)Ra levels in stream sediments (544-8759 Bq/kg) at the point of discharge were ~200 times greater than upstream and background sediments (22-44 Bq/kg) and above radioactive waste disposal threshold regulations, posing potential environmental risks of radium bioaccumulation in localized areas of shale gas wastewater disposal.

Bromuro de metilo como tratamiento cuarentenario para cítricos infestados por la mosca del Mediterráneo

p.171-176

The thermal desulfination of allylic sulfonyl halides

Allylic sulfonyl halides can be generated by halogenolysis of the corresponding triorganotin sulfinates. Allylic sulfonyl bromides and iodides undergo a first order, thermal desulfination with allylic rearrangement to yield the corresponding allylic halides. The desulfination of a cyclic allylic sulfonyl bromide is stereospecific, proceeding with T-syn bromine migration.

Can Pickering emulsion formation aid the removal of creosote DNAPL from porous media?

The purpose of this investigation was to examine the proposition that creosote, emplaced in an initially water saturated porous system, can be removed from the system through Pickering emulsion formation. Pickering emulsions are dispersions of two immiscible fluids in which coalescence of the dispersed phase droplets is hindered by the presence of colloidal particles adsorbed at the interface between the two immiscible fluid phases. Particle trapping is strongly favoured when the wetting properties of the particles are intermediate between strong water wetting and strong oil wetting. In this investigation the necessary chemical conditions for the formation of physically stable creosote-in-water emulsions protected against coalescence by bentonite particles were examined. It was established that physically stable emulsions could be formed through the judicious addition of small amounts of sodium chloride and the surfactant cetyl-trimethylammonium bromide. The stability of the emulsions was initially established by visual inspection. However, experimental determinations of emulsion stability were also undertaken by use of oscillatory rheology. Measurements of the elastic and viscous responses to shear indicated that physically stable emulsions were obtained when the viscoelastic systems showed a predominantly elastic response to shearing. Once the conditions were established for the formation of physically stable emulsions a "proof-of-concept" chromatographic experiment was carried out which showed that creosote could be successfully removed from a saturated model porous system. (C) 2007 Elsevier Ltd. All rights reserved.

Preparation of o/w emulsions stabilized by solid particles and their characterization by oscillatory rheology

The purpose of this investigation was to examine the preparation and characterisation of hexane-in-water emulsions stabilised by clay particles. These emulsions, called Pickering emulsions, are characterised by the adsorption of solid particles at the oil/water (o/w) interface. The development of an elastic film at the o/w interface following the adsorption of colloidal particles helps to promote emulsion stability. Three different solid materials were used: silica sand, kaolin, and bentonite. Particles were added to the liquid mixtures in the range of 0.5–10 g dm−3. Emulsions were prepared using o/w ratios of 0.1, 0.2, 0.3, and 0.4. The effect of sodium chloride, on the stability of the prepared emulsions, was assessed in the range of 0–0.5 mol dm−3. In addition the use of a cationic surfactant hexadecyl-trimethylammonium bromide (CTAB) as an aid to improving emulsion stability was assessed in the concentration range of 0–0.05% (w/v). Characterisation of emulsion stability was realised through measurements of rheological properties including non-Newtonian viscosity, the elastic modulus, G', the loss modulus, G", and complex modulus, G*. The stability of the emulsions was evaluated immediately after preparation and 4 weeks later. Using the stability criteria, that for highly stable emulsions: G' > G" and both G' and G" are independent of frequency (varpi) it was concluded that highly stable emulsions could be prepared using a bentonite concentration of 2% (or more); an o/w ratio greater than 0.2; a CTAB concentration of 0.01%; and a salt concentration of 0.05 M or less—though salt was required.

Identification of the region of non-A beta component (NAC) of alzheimer's disease amyloid responsible for its aggregation and toxicity

The non-beta-amyloid (Aß) component of Alzheimer's disease amyloid (NAC) and its precursor a-synuclein have been linked to amyloidogenesis in several neurodegenerative diseases. NAC and a-synuclein both form ß-sheet structures upon ageing, aggregate to form fibrils, and are neurotoxic. We recently established that a peptide comprising residues 3±18 of NAC retains these properties. To pinpoint the exact region responsible we have carried out assays of toxicity and physicochemical properties on smaller fragments of NAC. Toxicity was measured by the ability of fresh and aged peptides to inhibit the reduction of the redox dye 3-(4,5-dimethylthiazol-2-yl)-2,5 diphenyltetrazolium bromide (MTT) by rat pheochromocytoma PC12 cells and human neuroblastoma SHSY-5Y cells. On immediate dissolution, or after ageing, the fragments NAC(8±18) and NAC(8±16) are toxic, whereas NAC(12±18), NAC(9±16) and NAC(8±15) are not. Circular dichroism indicates that none of the peptides displays ß-sheet structure; rather all remain random coil throughout 24 h. However, in acetonitrile, an organic solvent known to induce ß sheet, fragments NAC(8±18) and NAC(8±16) both form ß-sheet structure. Only NAC(8±18) aggregates, as indicated by concentration of peptide remaining in solution after 3 days, and forms fibrils, as determined by electron microscopy. These findings indicate that residues 8±16 of NAC, equivalent to residues 68±76 in a-synuclein, comprise the region crucial for toxicity.

Do vesicle cells of the red alga Asparagopsis (Falkenbergia stage) play a role in bromocarbon production?

The Rhodophyceae (red algae) are an established source of volatile halocarbons in the marine environment. Some species in the Bonnemaisoniaceae have been reported to contain large amounts of halogens in structures referred to as vesicle cells, suggesting involvement of these specialised cells in the production of halocarbons. We have investigated the role of vesicle cells in the accumulation and metabolism of bromide in an isolate of the red macroalga Asparagopsis (Falkenbergia stage), a species known to release bromocarbons. Studies of laboratory-cultivated alga, using light microscopy, revealed a requirement of bromide for both the maintenance and formation of vesicle cells. Incubation of the alga in culture media with bromide concentrations below 64 mg l-1 (the concentration of Br- in seawater) resulted in a decrease in the proportion of vesicle cells to pericentral cells. The abundance of vesicle cells was correlated with bromide concentration below this level. Induction of vesicle cell formation in cultures of Falkenbergia occurred at concentrations as low as 8 mg l-1, with the abundance of vesicle cells increasing with bromide concentration up to around 100 mg l-1. Further studies revealed a positive correlation between the abundance of vesicle cells and dibromomethane and bromoform production. Interestingly, however, whilst dibromomethane production was stimulated by the presence of bromide in the culture media, bromoform release remained unaffected suggesting that the two compounds are formed by different mechanisms.