Avaliação da auto-suficiência energética de reatores anaeróbios no tratamento de esgoto sanitário e água cinza

The anaerobic treatment of sewage is widely employed in Brazil and it is an appreciated way for the treatment of effluents, helping to reduce the environmental impact in rivers. The methane gas obtained from the process can be applied to improve the energetic efficiency of the system, reducing the amount of waste and the cost of the treatment process. This work presents the net energy balance of anaerobic reactors applied to the treatment of sewage. The analysis was performed considering full-scale and laboratory-scale treatment systems. In laboratory scale, the results from three kinds of systems were compared regarding the biological treatment of greywater. Two of them (UASB7 and UASB12) were anaerobic and the other one was a combined anaerobic-aerobic system (UASB7/SBR6). Greywater methanization (compared to theoretical maximum) was calculated considering 100% removal (g BOD/day), the literature percentage removal and the anionic surfactant presence in the effluentt. For each of these three cases, the efficiencies were, respectively, 16.9%, 43.6% and 51.3% in UASB7 reactor, 25.6%, 50.3% and 59.2% in UASB12 reactor and 30.6%, 61.2% and 71.9% in UASB7/SBR6 reactor. The energetic potential was found to be 4.66x10-4, 7.77x10-4 and 5.12x10-4 kWh/L for the UASB7, UASB12 and UASB7/SBR6 reactors, respectively. The pumping system, the aeration (in the anaerobic-aerobic system) and the temperature controlled heating system were considered to calculate the energetic consumption. However, the third one was not employed since tropical regions like Brazil do not need heating systems and also because of its high energetic consumption. The calculated net energy balance in the reactors was negative in the case of greywater, respectively -0.16, -0.28 and -0.18 kWh/L for the reactors UASB7, UASB12 and UASB7/SRB6. In full scale (ETE Jardim das Flores - Rio Claro, SP), the average energy... (Complete abstract click electronic access below)

O perfil dos alunos do curso de Pedagogia da UNESP de Bauru (2007-2010)

The present work aims to expand and contribute to the understanding of issues related to social demands urgent today as regards of teachers’ formation of kindergarten and initial series. Through a survey of the profile of students in four years (2007-2010) of Pedagogy, UNESP, Bauru, I propose to trace discussions about the student profile that seeks to train teacher in higher education. This process will reveal the profile of the student who is preparing to enter the teaching profession and who in later years will work in public and private spheres of education as a teacher, coordinator and manager in the kindergarten and elementary education. For this research will develop both qualitative approach in that it analyzes the profile to the light of the literature and studied quantitatively the extent that is based on the results

Avaliação da viabilidade econômica do uso de um aquecedor solar de água de garrafas pet para aquecer o ar de uma cabine de pintura e uma estufa de secagem

Nowadays, the biggest part of the world's energy supply comes from fossil fuels and nuclear. However, the current need of the society for the preservation of the environment and wise use of natural resources, has favored the search for alternative energy sources and improvement of energy efficiency. In this new scenario, companies are beginning to mobilize in order to adapt its facilities to renewable energy. Solar, with its immense potential, not really exploited yet, can be very useful for companies that want to beat their sustainability goals. Given these facts, the aim is to evaluate the economic viability of introducing a solar water heater which uses a colorless PET bottle as one of its components in a plant. The hot water generated will heat the air of a paint booth and a warm house, reducing energy consumption, since they are heated by electric heaters

Avaliação da tenacidade à fratura em juntas soldadas circunferenciais de tubulações de processo

This work aims to analyze the toughness of a welded joint in the presence of a crack through the analysis of maximum tension the material can withstand the presence of this type of defect, since a discontinuity is likely to occur in this type of joint and its detection and its design is simple, using non-destructive testing techniques. The study will be conducted through the CTOD test - Crack-Tip Opening Displacement, with type specimens SE (B) - Single Edge Bend taken from a weld in the L-C position in relation to the length (longitudinal axis) of a test tube. The main idea is to simulate the welding conditions for the manufacture of industrial pipes, made in boiler shops (pipe-shop) within petrochemical plants. These pipes are often subject to operation with flammable and toxic subjected to high pressures and temperatures, where one can break the line can cause irreparable damage to the plant, the environment and the health of surrounding communities. With this study we evaluate whether the weld metal has the same properties as fracture toughness of the base material. This study shows the importance of using a qualified welding procedure for performing quality welds while maintaining the properties of the fracture toughness of the base metal. It was found from the results of tests using a welding procedure described for carrying out welding ensures mechanical properties very close to the base metal, which in terms of design is great, since one can ensure that the weld will the same characteristics of the base metal specified for the assembly of the pipe

Avaliação de funcionamento das bombas hidráulicas do sistema de tratamento de efluentes da Empresa Parker Hannifin

On the field of the projects of hydraulic systems exists a lot of worries when we talk about the calculate of hydraulic pumps. In this case some facts must be considerate: length of tubes, fluid characteristics, height gauge, temperature, pressure, characteristics of tubes, flow required and others. For that mathematic calculates must be developed with the objective to optimize hydraulic pumps and agree to find an ideal machine (that don't requires more energy than necessary or less energy than it requires; that is the more critical case, cause exists the risk that the fluid pumped do not agree to become in your destiny). The wrong calculate of this machine can super-size its, bringing an excessive energy consumption. Actually it's an important subject because we are in the age of lack of energy what turn it more expensive. So the correct sizing of a hydraulic pump is connected with the fact that you have to uses the enough energy resources avoiding waste. The calculate of ideal pump in the pumping system is studied during years and a lot of specialists in this subject develop equations and theories to calculate its. Some researches study about this subject and all of them become to the same conclusion: to find the ideal pump we have to know the characteristics of fluid (cinematic viscosity), the required flow , overall yield (overall of motor x overall of pump) the high gauge or discharge pressure and the loss of repression. The pressure drop can be calculated with different theories: using Hazen-Williams, Darcy e Weisbach or Chézy (1775 - that starts the researches to calculate the pressure drop). Although the most used theory and what is most near to reality is the Darcy's equation. So, in this job the Darcy's equation were choice to calculate the drop pressure that consider what kind of flow we are studying: laminar or turbulent. The determination of the best pump to be used in the ... ( complete abstract click eletronic access below)

Estudo químico e avaliação da atividade antioxidante e antimicrobiana dos escapos de Syngonanthus nitens (bong.) Ruhland. (Eriocaulaceae)

Neste trabalho é apresentado o estudo químico dos escapos de Syngonanthus nitens (Bong.) Ruhland, pertencente à família Eriocaulaceae. O extrato metanólico foi preparado por percolação, concentrado e fracionado em coluna de permeação em gel. As frações obtidas foram analisadas por CCDC e purificadas por HSCCC, HPLC-RI e HPLC-PDA. As estruturas foram determinadas usando ultravioleta, técnicas mono e bidimensionais de RMN e espectrometria de massas com fonte electrospray e analisador íon trap (modo de inserção direta). O perfil cromatográfico de HPLC-PDA mostrou que as flavonas derivadas da luteolina são os seus principais constituintes químicos. Foram isoladas as substâncias: 7-metoxiluteolina-8-C-β-D-glicopiranosídeo (SN1), 7-metoxiluteolina-6-C-β-D-glicopiranosídeo (SN2), 3',7-dimetoxiluteolina-6-C-β-D-glicopiranosídeo (SN3), luteolina (SN4), 6-hidroxiluteolina (SN5), luteolina-6-C--D-glicopiranosídeo (Sn6), 6-hidroxiluteolina-7-O--D-galactopiranosideo (Sn7) e 7-metoxiluteolina-6-C- β-D-glicopiranosideo-(3'-O-3''')-7ʹ-metoxiluteolina-8'-C-β-D-glicopiranosídeo (Sn8). Foram avaliadas as atividades antioxidantes do extrato metanólico dos escapos de S. nitens e do biflavonóide identificado, os quais apresentaram atividade significativa quando comparada com os padrões do ácido gálico, rutina e quercetina . A atividade antimicrobiana do extrato metanólico dos escapos e das substâncias identificadas derivadas da luteolina foram também avaliadas. O extrato metanólico dos escapos apresentou melhor atividade antimicrobiana, quando comparada com os demais flavonoides isolados e identificados do mesmo extrato. Finalmente, foi avaliada a atividade antiulcerogênica do extrato metanolico dos escapos, utilizando-se o modelo de lesão ulcerativa induzida por etanol absoluto

Avaliação da regeneração natural em trechos da mata ciliar do rio Moji-Guaçu, Pirassununga-SP

O presente trabalho teve por objetivo analisar e quantificar o banco de plântulas em trechos de Mata Ciliar do Rio Moji-Guaçu situados na Academia da Força Aérea (AFA) em Pirassununga-SP. Os trechos definidos para a amostragem foram relacionados com as condições do entorno e com a estrutura da comunidade local. Foi realizada uma avaliação da diversidade e da dominância de guildas que se encontram presentes nesse compartimento da regeneração natural, o que forneceu informações das espécies que contribuem de forma mais expressiva para a manutenção da comunidade florestal, bem como aquelas respectivas a grupos funcionais que caracterizam as condições sucessionais da estrutura atual dos segmentos de mata analisados. Na análise dos parâmetros fitossociológicos encontrou-se um Índice de Shannon-Wiener (H’) de diversidade de 3,843 nits/ind, índice de equabilidade de Pielou (J’) de 0,84, e índice de dominância de Simpson de 0,034. A síndrome de dispersão zoocórica correspondeu a quase 60% das espécies, no trecho ciliar estudado. A classe sucessional das espécies não pioneiras recebeu maior destaque, representada por 50% das espécies amostradas, mas também as lianas ocorreram com expressão no banco de plântulas analisado. Embora os padrões aqui observados possam ser generalizados, no entanto com cautela, o presente trabalho traz resultados importantes, apesar de primários, pois medidas visando à preservação e à restauração florestal dependem, primeiramente, do conhecimento sobre as espécies com ocorrência na área, sua biologia e histórico de abrangência na paisagem

Avaliação da toxicidade do dióxido de carbono no sistema nervoso de Apis mellifera (Hymenoptera, Apidae)

A concentração de dióxido de carbono (CO2) global eleva-se a cada ano, isso deve-se a um desequilíbrio entre as taxas de emissão deste gás por atividades antropogênicas e fontes naturais e a taxa que a biosfera e oceanos o removem da atmosfera. O CO2 é um importante constituinte químico do ambiente, pois este é um gás que aprisiona radiação infravermelha emitida pela superfície da Terra, contribuindo, assim, para a manutenção da temperatura global necessária a vida. As alterações na concentração de CO2 na atmosfera afetam inúmeros animais que dependem que estas estejam altamente controladas para poderem sobreviver. Em abelhas Apis mellifera valores elevados de temperatura ou níveis de CO2 dentro da colméia podem ter efeitos deletérios. Estes insetos são considerados bioindicadores naturais, pois apresentam diferenças fisiológicas conforme as condições do ambiente, sendo utilizadas na avaliação de efeitos a várias substâncias presentes no meio. Atualmente uma das técnicas utilizadas para a avaliação do efeito de estímulos externos é a utilização da marcação da proteína c-Fos através da expressão do gene c-fos, que indicam tanto a existência de atividade celular como também possibilita a identificação de áreas cerebrais determinadas. Esta proteína foi utilizada com o intuído de verificar se concentrações elevadas de gás carbônico são capazes de alterar as funções cerebrais da abelha Apis mellifera, comprometendo sua atividade de orientação e, conseqüentemente seu forrageamento. Marcações positivas à proteína Fos foram observadas nas regiões dos lobos ópticos e ocelos tanto do grupo controle quanto dos grupos Resumo Jacob, C. R. O. 9 expostos ao gás dióxido de carbono para todas as idades coletadas, estes resultados estão relacionados com a...(Resumo completo, clicar acesso eletrônico abaixo)

Avaliação de diferentes dietas na manutenção dos cupins Heterotermes tenuis e Cornitermes cumulans (Isoptera, Rhinotermitidae, Termitidae) em condições laboratoriais

Não disponível

Validação do instrumento de avaliação do jogador de futebol em situação de jogo

In the literature, it is possible to find a large number of studies directed toward athletic training in the physical, technical and tactical aspects of the Soccer game. In the other side, we are able to attest that there exists few instruments in the sport area of studies on evaluation of the athlete, in specific, rare are the instruments for assessment that takes into consideration the game situation. The most important aspect of an instrument of assessment is its validity. The present study has the objective to validate the “Instrument for Assessment of the Soccer Player” (IASP), proposed by Gama (2003). For the process of validation, participated nine university students, volunteers, four women and five men. The evaluators had a training period for acquaintance with the instrument and they analyzed, in individual basis, soccer games registered in video. This procedure was done via a 29 inches TV set, a DVD device and a voice recorder. Tests of reliability and objectivity were applied in order to measure intra and between observers consistency. As for the objectivity analysis, the results for each one of the soccer motor action with the ball in a game situation showed high correlation between possible score and obtained score. However these data did not allow for the validation of the IASP instrument as the criterion applied to the analyzed actions were different between observers even when of the observation of the same player in the same game. This problem was detected also in the evaluation of reliability. However, the present study was capable to point out inconsistencies within the Instrument for Assesment of the Soccer Player (IASP) so that after the needed changes being made, another validation will be done

Influência do uso de hipoclorito de sódio 2,5% e extrato glicólico de sálvia 20% durante o preparo biomecânico sobre a resistência adesiva de retentores intra- radiculares: avaliação através do teste de push-out

The aim of this study it was to evaluate the use of irrigating solution used during root canal preparation on the adhesive cementation of prefabricated fiberglass pins. The bond strength between different regions of the root and the fiberglass pins cemented into the root canal were evaluated by push-out assay. For this study, 36 human teeth were used, all equally prepared. The irrigating solutions used for biomechanical preparation were: saline solution, sodium hypochlorite 2,5% and glycolic extract of salvia 20%. The dual cure resin cement was used for cementation of pins. After cementation, specimens were sectioned to give 3 slices of approximately 2 mm each (cervical, middle and apical), which were submitted to mechanical push-out test. Were performed ANOVA and Tukey's test with a significance level of 5%, for the analysis of mechanical test. Comparing the thirds we observed that the only solution that presented statistical difference in the bond strength was sodium hypochlorite, which showed higher values for the middle and apical third compared with the cervical third, but when compared without taking into consideration the dental thirds, solutions studied showed no differences in bond strength. Therefore, it was concluded that the solutions studied can be used during endodontic treatment without causing harmful effects on the final adhesive restoration

Avaliação do metabolismo oxidativo em cepas de Trypanosoma cruzi naturalmente resistentes ao benzonidazol

O agente etiológico da doença de Chagas, Trypanosoma cruzi, é responsável pela infecção de milhões de pessoas na América Latina. No momento há apenas dois fármacos disponíveis, o nifurtimox (5-nitrofurano), teve o uso descontinuado no Brasil, e o benzonidazol (2-nitroimidazole), embora ambos possuam ações limitadas, visto que dependem da fase da doença, das condições fisiológicas do hospedeiro, da suscetibilidade e variabilidade genética da cepa. Assim, a busca de novas moléculas torna-se urgente e necessária, bem como a compreensão do mecanismo de resistência aos fármacos tripanocidas. Alguns estudos relatam aumento na produção de enzimas que atuam na defesa celular, as quais, provavelmente, poderiam ser responsáveis pela resistência de certas cepas do parasita. Tais enzimas têm funções importantes na sobrevivência e crescimento dos parasitas: superóxido dismutase (SOD), uma metaloenzima que elimina radicais superóxido ao convertê-los em peróxido de hidrogênio e oxigênio molecular; old yellow enzyme (OYE), que é uma NADPH flavina oxidoredutase e pode estar envolvida na redução de substâncias tripanocidas; e, peroxiredoxina (Prx), que catalisa a redução de peróxidos. O objetivo deste projeto é avaliar a suscetibilidade de diferentes cepas ao benzonidazol, clonar, sequenciar e expressar enzimas possivelmente envolvidas na resistência a este fármaco e realizar análises morfológicas serão nos parasitos após serem expostos à substância em questão. Futuramente os anticorpos policlonais obtidos a partir das proteínas recombinantes de Prx, SOD e OYE serão empregados para avaliar o nível de expressão das mesmas em parasitas tratados e não tratados com o benzonidazol.

Avaliação do comportamento mecânico sob deformação da liga Ti- 30Ta visando aplicações biomédicas

Titanium and its alloys have been used for biomedical applications due their excellent properties such as high corrosion resistance, biocompatibility and mechanical properites. In this study, microstructural and mechanical properties of Ti-30Ta alloy was evaluated during its processing. Ti-30Ta alloy ingots were produced from sheets of commercially pure titanium (99.9%) and tantalum (99.9%). Its melting was realized in arc melting furnace in an argon atmosphere. After homogenizing at 1200ºC, ingots were cold worked by swaging. Samples with 13 mm in diameter were obtained. They were forging at the reduction ratios of 15%. After deformation, microstructure was evaluated by optical microscopy in each condition. Also, Vickers microhardness of samples was measured and phase constitution was evaluated using XRD analysis

Importância da avaliação de hematúrias através do dismorfismo eritrocitário

A hematúria é a eliminação de um número anormal de hemácias na urina e suas causas são múltiplas e nem sempre a investigação clínica é simples. A indicação para se estabelecer a diferenciação entre as causas das hematúrias, se glomerulares ou não glomerulares é feita através de solicitação específica do exame de dismorfismo eritrocitário. Esse exame é realizado em urina recém emitida, colhida em jato médio, por meio de microscopia de contraste de fase onde a morfologia das hemácias pode sugerir a origem da hematúria, direcionando o diagnóstico e conduta terapêutica pelo clínico. Neste projeto estudou-se a aplicação da caracterização das hemácias por microscopia de contraste de fase nos casos de hematúrias detectadas, sem a presença de leucocitúrias (sinais que sugerem infecção do trato urinário) nos achados de sedimentoscopia urinária realizados na rotina do setor de bioquímica clínica do CRD-Nac-UNESP, avaliando assim a importância da indicação da aplicação deste procedimento para a clínica

Avaliação do ciclo de vida dos tubos de PVC produzidos no Brasil

Naturally characterizes the human being the interference in the environment to ensure their survival and also convenience. After numerous environmental accidents caused by unbridled pursuit of this goal, the concern about providing for current needs without compromising the ability of the future generations to supply their own, gained space. In order to contribute to sustainable development the Life Cycle Assessment (LCA) was implemented. This tool is based on the concept that if the environmental impacts of a product or service are known, it is possible to take better decisions concerning its environmental aspects. The purpose of this research is to conduct the LCA of polyvinyl chloride (PVC), the world’s second most consumed thermoplastic. The methodology described in NBR ISO 14040 and NBR ISO 14044 was followed. As a result, the LCA of polyvinyl chloride produced in Brazil was obtained, and, therefore, the inventory of the product in question adapted to Brazilian reality. The research can be applied to various studies considering that actions were taken to ensure that it represents the Brazilian reality. Moreover, the procedures were described to guarantee the greatest transparency possible