Correct procedures for the calculation of heats of adsorption for heterogeneous adsorbents from molecular simulation

Several procedures for calculating the heat of adsorption from Monte Carlo simulations for a heterogeneous adsorbent are presented. Simulations have been performed to generate isotherms for nitrogen at 77 K and methane at 273.15 K in graphitic slit pores of various widths. The procedures were then applied to calculate the heat of adsorption of an activated carbon with an arbitrary pore size distribution. The consistency of the different procedures shows them to be correct in calculating interaction energy contributions to the heat of adsorption. The currently favored procedure for this type of calculation, from the literature, is shown to be incorrect and in serious error when calculating the heat of adsorption of activated carbon.

Adsorption dynamics measured by permeation and batch adsorption methods

We have measured the adsorption equilibrium and kinetics of carbon dioxide on a commercially available activated carbon by two methods; permeation and batch adsorption. The two methods are compared and found to yield consistent results. All experiments are performed at low pressure (

Methyl chloride purification for the silicone industry

This study experimentally investigated methyl chloride (MeCl) purification method using an inhouse designed and built volumetric adsorption/desorption rig. MeCl is an essential raw material in the manufacture of silicone however all technical grades of MeCl contain concentrations (0.2 - 1.0 % wt) of dimethyl ether (DME) which poison the process. The project industrial partner had previously exhausted numerous separation methods, which all have been deemed not suitable for various reasons. Therefore, adsorption/desorption separation was proposed in this study as a potential solution with less economic and environmental impact. Pure component adsorption/desorption was carried out for DME and MeCl on six different adsorbents namely: zeolite molecular sieves (types 4 Å and 5 Å); silica gels (35-70 mesh, amorphous precipitated, and 35-60 mesh) and granular activated carbon (type 8-12 mesh). Subsequent binary gas mixture adsorption in batch and continuous mode was carried out on both zeolites and all three silica gels following thermal pre-treatment in vacuum. The adsorbents were tested as received and after being subjected to different thermal and vacuum pre-treatment conditions. The various adsorption studies were carried out at low pressure and temperature ranges of 0.5 - 3.5 atm and 20 - 100 °C. All adsorbents were characterised using Brunauer Emmett Teller (BET), thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and energy dispersive x-ray analysis (EDXA) to investigate their physical and chemical properties. The well-known helium (He) expansion method was used to determine the empty manifold and adsorption cell (AC) regions and respective void volumes for the different adsorbents. The amounts adsorbed were determined using Ideal gas laws via the differential pressure method. The heat of adsorption for the various adsorbate-adsorbent (A-S) interactions was calculated using a new calorimetric method based on direct temperature measurements inside the AC. Further adsorption analysis included use of various empirical and kinetic models to determine and understand the behaviour of the respective interactions. The gas purification behaviour was investigated using gas chromatography and mass spectroscopy (GC-MC) analysis. Binary gas mixture samples were syringed from the manifold iii and AC outlet before and after adsorption/desorption analysis through manual sample injections into the GC-MS to detect and quantify the presence of DME and ultimately observe for methyl chloride purification. Convincing gas purification behaviour was confirmed using two different GC columns, thus giving more confidence on the measurement reliability. From the single pure component adsorption of DME and MeCl on the as received zeolite 4A subjected to 1 h vacuum pre-treatment, both gases exhibited pseudo second order adsorption kinetics with DME exhibiting a rate constant nearly double that of MeCl thus suggesting a faster rate of adsorption. From the adsorption isotherm classification both DME and MeCl exhibited Type II and I adsorption isotherm classifications, respectively. The strength of bonding was confirmed by the differential heat of adsorption measurement, which was found to be 23.30 and 10.21 kJ mol-1 for DME and MeCl, respectively. The former is believed to adsorb heterogeneously through hydrogen bonding whilst MeCl adsorbs homogenously via van der Waal’s (VDW) forces. Single pure component adsorption on as received zeolite 5A, silica gels (35-70, amorphous precipitated and 35-60) resulted in similar adsorption/desorption behaviour in similar quantities (mol kg-1). The adsorption isotherms for DME and MeCl on zeolite 5A, silica gels (35-70, amorphous precipitated and 35-60) and activated carbon 8-12 exhibited Type I classifications, respectively. Experiments on zeolite 5A indicated that DME adsorbed stronger, faster and with a slightly stronger strength of interaction than MeCl but in lesser quantities. On the silica gels adsorbents, DME exhibited a slightly greater adsorption capacity whilst adsorbing at a similar rate and strength of interaction compared to MeCl. On the activated carbon adsorbent, MeCl exhibited the greater adsorption capacity at a faster rate but with similar heats of adsorption. The effect of prolonged vacuum (15 h), thermal pre-treatment (150 °C) and extended equilibrium time (15 min) were investigated for the adsorption behaviour of DME and MeCl on both zeolites 4A and 5A, respectively. Compared to adsorption on as received adsorbents subjected to 1 h vacuum the adsorption capacities for DME and MeCl were found to increase by 1.95 % and 20.37 % on zeolite 4A and by 4.52 % and 6.69 % on zeolite 5A, respectively. In addition the empirical and kinetic models and differential heats of adsorption resulted in more definitive fitting curves and trends due to the true equilibrium position of the adsorbate with the adsorbent. Batch binary mixture adsorption on thermally and vacuum pre-treated zeolite 4A demonstrated purification behaviour of all adsorbents used for MeCl streams containing DME impurities, with a concentration as low as 0.66 vol. %. The GC-MS analysis showed no DME detection for the tested concentration mixtures at the AC outlet after 15 or 30 min, whereas MeCl was detectable in measurable amounts. Similar behaviour was also observed when carrying out adsorption in continuous mode. On the other hand, similar studies on the other adsorbents did not show such favourable MeCl purification behaviour. Overall this study investigated a wide range of adsorbents (zeolites, silica gels and activated carbon) and demonstrated for the first time potential to purify MeCl streams containing DME impurities using adsorption/desorption separation under different adsorbent pre-treatment and adsorption operating conditions. The study also revealed for the first time the adsorption isotherms, empirical and kinetic models and heats of adsorption for the respective adsorbentsurface (A-S) interactions. In conclusion, this study has shown strong evidence to propose zeolite 4A for adsorptive purification of MeCl. It is believed that with a technical grade MeCl stream competitive yet simultaneous co-adsorption of DME and MeCl occurs with evidence of molecular sieiving effects whereby the larger DME molecules are unable to penetrate through the adsorbent bed whereas the smaller MeCl molecules diffuse through resulting in a purified MeCl stream at the AC outlet. Ultimately, further studies are recommended for increased adsorption capacities by considering wider operating conditions, e.g. different adsorbent thermal and vacuum pre-treatment and adsorbing at temperatures closer to the boiling point of the gases and different conditions of pressure and temperature.

Development of micro immunosensors to study genomic and proteomic biomarkers related to cancer and Alzheimer's disease

A report from the National Institutes of Health defines a disease biomarker as a “characteristic that is objectively measured and evaluated as an indicator of normal biologic processes, pathogenic processes, or pharmacologic responses to a therapeutic intervention.” Early diagnosis is a crucial factor for incurable disease such as cancer and Alzheimer’s disease (AD). During the last decade researchers have discovered that biochemical changes caused by a disease can be detected considerably earlier as compared to physical manifestations/symptoms. In this dissertation electrochemical detection was utilized as the detection strategy as it offers high sensitivity/specificity, ease of operation, and capability of miniaturization and multiplexed detection. Electrochemical detection of biological analytes is an established field, and has matured at a rapid pace during the last 50 years and adapted itself to advances in micro/nanofabrication procedures. Carbon fiber microelectrodes were utilized as the platform sensor due to their high signal to noise ratio, ease and low-cost of fabrication, biocompatibility, and active carbon surface which allows conjugation with biorecognition moieties. This dissertation specifically focuses on the detection of 3 extensively validated biomarkers for cancer and AD. Firstly, vascular endothelial growth factor (VEGF) a cancer biomarker was detected using a one-step, reagentless immunosensing strategy. The immunosensing strategy allowed a rapid and sensitive means of VEGF detection with a detection limit of about 38 pg/mL with a linear dynamic range of 0–100 pg/mL. Direct detection of AD-related biomarker amyloid beta (Aβ) was achieved by exploiting its inherent electroactivity. The quantification of the ratio of Aβ1-40/42 (or Aβ ratio) has been established as a reliable test to diagnose AD through human clinical trials. Triple barrel carbon fiber microelectrodes were used to simultaneously detect Aβ1-40 and Aβ1-42 in cerebrospinal fluid from rats within a detection range of 100nM to 1.2μM and 400nM to 1μM respectively. In addition, the release of DNA damage/repair biomarker 8-hydroxydeoxyguanine (8-OHdG) under the influence of reactive oxidative stress from single lung endothelial cell was monitored using an activated carbon fiber microelectrode. The sensor was used to test the influence of nicotine, which is one of the most biologically active chemicals present in cigarette smoke and smokeless tobacco.

An ether-functionalised cyclic sulfonium based ionic liquid as an electrolyte for electrochemical double layer capacitors

A novel cyclic sulfonium cation-based ionic liquid (IL) with an ether-group appendage and the bis{(trifluoromethyl)sulfonyl}imide anion was synthesised and developed for electrochemical double layer capacitor (EDLC) testing. The synthesis and chemical-physical characterisation of the ether-group containing IL is reported in parallel with a similarly sized alkyl-functionalised sulfonium IL. Results of the chemical-physical measurements demonstrate how important transport properties, i.e. viscosity and conductivity, can be promoted through the introduction of the ether-functionality without impeding thermal, chemical or electrochemical stability of the IL. Although the apparent transport properties are improved relative to the alkyl-functionalised analogue, the ether-functionalised sulfonium cation-based IL exhibits moderately high viscosity, and poorer conductivity, when compared to traditional EDLC electrolytes based on organic solvents (propylene carbonate and acetonitrile). Electrochemical testing of the ether-functionalised sulfonium IL was conducted using activated carbon composite electrodes to inspect the performance of the IL as a solvent-free electrolyte for EDLC application. Good cycling stability was achieved over the studied range and the performance was comparable to other solvent free,
IL-based EDLC systems. Nevertheless, limitations of the attainable performance are primarily the result of sluggish transport properties and a restricted operative voltage of the IL, thus highlighting key aspects of this field which require further attention.

Specific Filters Applied in Nuclear Medicine Services

In Nuclear Medicine, radioiodine, in various chemical forms, is a key tracer used in diagnostic practices and/or therapy. Due to its high volatility, medical professionals may incorporate radioactive iodine during the preparation of the dose to be administered to the patient. In radioactive iodine therapy doses ranging from 3.7 to 7.4GBq per patient are employed. Thus, aiming at reducing the risk of occupational contamination, we developed a low cost filter to be installed at the exit of the exhaust system where doses of radioactive iodine are fractionated, using domestic technology. The effectiveness of radioactive iodine retention by silver impregnated silica [10%] crystals and natural activated carbon was verified using radiotracer techniques. The results showed that natural activated carbon is effective for I2 capture for a large or small amount of substrate but its use is restricted due to its low flash point (150º C). Besides, when poisoned by organic solvents, this flash point may become lower, causing explosions if absorbing large amounts of nitrates. To hold the CH3I gas, it was necessary to increase the volume of natural activated carbon since it was not absorbed by SiO2 + Ag crystals. We concluded that, for an exhaust flow range of (306 4) m3/h, a double stage filter using SiO2 + Ag in the first stage and natural activated carbon in the second is sufficient to meet radiological safety requirements.

A bio-coke for anode production and the manufacturing method thereof

Dans l’industrie de l’aluminium, le coke de pétrole calciné est considéré comme étant le composant principal de l’anode. Une diminution dans la qualité du coke de pétrole a été observée suite à une augmentation de sa concentration en impuretés. Cela est très important pour les alumineries car ces impuretés, en plus d’avoir un effet réducteur sur la performance des anodes, contaminent le métal produit. Le coke de pétrole est aussi une source de carbone fossile et, durant sa consommation, lors du processus d’électrolyse, il y a production de CO2. Ce dernier est considéré comme un gaz à effet de serre et il est bien connu pour son rôle dans le réchauffement planétaire et aussi dans les changements climatiques. Le charbon de bois est disponible et est produit mondialement en grande quantité. Il pourrait être une alternative attrayante pour le coke de pétrole dans la fabrication des anodes de carbone utilisées dans les cuves d’électrolyse pour la production de l’aluminium. Toutefois, puisqu’il ne répond pas aux critères de fabrication des anodes, son utilisation représente donc un grand défi. En effet, ses principaux désavantages connus sont sa grande porosité, sa structure désordonnée et son haut taux de minéraux. De plus, sa densité et sa conductivité électrique ont été rapportées comme étant inférieures à celles du coke de pétrole. L’objectif de ce travail est d’explorer l’effet du traitement de chaleur sur les propriétés du charbon de bois et cela, dans le but de trouver celles qui s’approchent le plus des spécifications requises pour la production des anodes. L’évolution de la structure du charbon de bois calciné à haute température a été suivie à l’aide de différentes techniques. La réduction de son contenu en minéraux a été obtenue suite à des traitements avec de l’acide chlorhydrique utilisé à différentes concentrations. Finalement, différentes combinaisons de ces deux traitements, calcination et lixiviation, ont été essayées dans le but de trouver les meilleures conditions de traitement.

Estudo cinético do branqueamento do óleo da carpa (Cyprinus carpio L)

O óleo de pescado é caracterizado por ser uma fonte rica de ácidos graxos poliinsaturados ω-3, desde modo a sua oxidação lipídica se torna mais favorável quando comparado com outros óleos de origem vegetal. O objetivo do presente trabalho foi a otimização da etapa de branqueamento através da metodologia de superfície de resposta, sendo utilizado misturas de carvão ativado e terra ativada (Tonsil) para a remoção da cor e dos produtos de oxidação, procurando-se preservar o conteúdo total de carotenóides no óleo de carpa. O óleo bruto de carpa (Cyprinus carpio L.) para a realização do trabalho foi obtido a partir da realização de ensilagem ácida, passando posteriormente pelas etapas de refino: degomagem, neutralização, lavagem, secagem e branqueamento. A otimização da etapa de branqueamento foi realizada através de um planejamento fatorial composto central, com os fatores de estudo: a quantidade de adsorvente (Ads) e a quantidade de carvão ativado (Ca), sendo consideradas como respostas o conteúdo total de carotenóides e o valor de TBA. Na melhor condição do branqueamento do óleo de carpa foi realizado um estudo cinético, e para o cálculo das constantes cinéticas foram utilizados os modelos de Brimberg modificado e de Langmuir-Hinshelwood, A condição ótima do branqueamento foi com 2% de adsorvente e 10% de carvão ativado, onde ocorreram menores perdas de carotenóides (44,40%), com redução da cor escura presente no óleo de (85,62%) e redução do valor de TBA (73,10%), obtendo-se um óleo branqueado de carpa com qualidade oxidativa e melhor aspecto em relação à cor. Os dois modelos cinéticos representaram de forma satisfatória os dados experimentais do branqueamento do óleo de carpa, pelos altos coeficientes de determinação e baixos erros médios relativos apresentados. Foi possível observar que ocorreu uma rápida adsorção dos pigmentos carotenóides, e após 30 min a adsorção foi menos eficiente. Nos óleos bruto e branqueado de vísceras de carpa não foi identificada diferença significativa entre as concentrações de ácidos graxos, demonstrando que as etapas de refino utilizadas não alteraram o perfil de ácidos graxos do óleo bruto.

Avaliação de Impacto Ambiental, Valorização do Efluente e dos Resíduos Sólidos da Indústria Corticeira

A preocupação com o meio ambiente, nomeadamente na descarga de águas residuais, consumo de água excessivo e produção de resíduos industriais, está cada vez mais presente no quotidiano. Devido a estas problemáticas, efetuou-se a avaliação de impacte ambiental (AIA) do processo produtivo das rolhas de cortiça naturais, tratamento das águas de cozedura da cortiça (estudo da possível reutilização do efluente tratado) e valorização de subprodutos – resíduo sólido (raspa de cortiça), sendo estes os objetivos propostos para a realização da presente dissertação. Na AIA, efetuada no decorrer das fases da Análise do Ciclo de Vida (ACV), foram selecionadas 8 categorias de impacte – aquecimento global, acidificação, dessecação, toxicidade e ecotoxicidade, eutrofização, consumo de recursos não renováveis e oxidação foto-química. A água de cozedura caracterizou-se por uma elevada carga poluente, apresentando elevada concentração de cor, Carência Química de Oxigénio (CQO), taninos e lenhina e Sólidos Suspensos Totais (SST). O processo de tratamento proposto consistiu num pré-tratamento por ultrafiltração (UF), com membranas de 30.000 e 20.000 MWCO, seguido de adsorção por carvão ativado (comercial e produzido a partir de raspa de cortiça). No tratamento por UF, utilizando uma membrana de 30.000 MWCO, foram obtidas percentagens de remoção para a primeira amostra de água de cozedura de 74,8 % para a cor, 33,1 % para a CQO e para a segunda amostra de 85,2 % para a cor e 41,8 % para a CQO. Posteriormente, apenas para a segunda amostra de água de cozedura e com uma membrana de 20.000 MWCO, as percentagens de remoção obtidas foram superiores, de 93% para a cor, 68,9 % para a CQO, 88,4 % para taninos e lenhina e 43,0 % para azoto total. No tratamento por adsorção com carvão ativado estudou-se o tempo de equilíbrio do carvão ativado comercial e do carvão ativado produzido a partir de aparas de cortiça, seguindo-se o estudo das isotérmicas de adsorção, no qual foram analisados os parâmetros da cor e CQO para cada solução. Os ajustes dos modelos teóricos aos pontos experimentais demonstraram que ambos os modelos (Langmuir e Freundlich) poderiam ser considerados, uma vez que apresentaram ajustes idênticos. Relativamente ao tratamento de adsorção em contínuo do permeado, obtido por UF com membrana de 20.000 MWCO, constatou-se que ambos os carvões ativados (comercial e produzido) não ficaram saturados, tendo em consideração os tempos de saturação estimados pela capacidade máxima de adsorção (determinada para a isotérmica de Langmuir) e as representações gráficas dos valores experimentais obtidos para cada ensaio. No ensaio de adsorção com carvão ativado comercial verificou-se que o efluente tratado poderia ser descarregado no meio hídrico ou reutilizado no processo industrial (considerando os parâmetros analisados), uma vez que até aos 11 minutos de ensaio a concentração da solução à saída foi de 111,50 mg/L O2, para a CQO, e incolor, numa diluição de 1:20. Em relação à adsorção em contínuo com carvão ativado produzido verificou-se no ensaio 4 que o efluente resultante apresentou uma concentração de CQO de 134,5 mg/L O2 e cor não visível, numa diluição de 1:20, ao fim de 1h22 min de ensaio. Assim, concluiu-se que os valores obtidos são inferiores aos valores limite de emissão (VLE) presentes no Decreto-Lei n.º 236/98 de 1 de Agosto. O carvão ativado produzido apresentou elevada área superficial específica, com 870 m2/g, comparativamente ao carvão comercial que foi de 661 m2/g. O processo de extração da suberina a partir de raspa de cortiça isenta de extraíveis, efetuado através da metanólise alcalina, apresentou percentagens de extração superiores aos restantes métodos. No processo efetuado em scale-up, por hidrólise alcalina, obteve-se uma extração de 3,76 % de suberina. A aplicação da suberina no couro demonstrou que esta cera apresenta enormes potencialidades, uma vez que a sua aplicação confere ao couro um aspeto sedoso, com mais brilho e um efeito de “pull-up”.

Amphiphilic catalysts for the treatment of oily wastewaters

The main objective of this study was to obtain an effective catalyst for removal of diazo dye - Sudan IV by Catalytic Wet Peroxide Oxidation (CWPO). For this purpose liquid phase treatment was used to increase the basicity of activated carbon surface favoring the adsorption of organic pollutants. Modified activated carbon catalysts were used in different types of experiments: 1) decomposition of H2O2 in aquatic media, 2) decomposition of H2O2 in organic media, 3) adsorption of Sudan IV, 4) Sudan IV removal by CWPO. As the result of all of these experiments the most effective catalyst was obtained and discussed. It was not observed removal of Sudan IV from biphasic system by CWPO. The obtained results in some cases show a slight increase in concentration of Sudan IV, which may be ascribed to experimental errors. Different factors could be the reason of those errors. For example, the high volatility properties of organic media used in experiments should be taken into account during experiments. Under settled reaction temperature the decrease of cyclohexane volume during experiment could give rise in Sudan IV concentration. The initial concentration of model diazo dye also should be reviewed more detailed for CWPO experiments. Despite of these experimental errors the behavior of our catalysts in different media was observed.

Pore size distributions derived from adsorption isotherms, immersion calorimetry, and isosteric heats: A comparative study

We compare the pore size distribution of a well-characterized activated carbon derived from model-dependent, adsorption integral equation (AIE) methods with those from model-independent, immersion calorimetry and isosteric heat analyses. The AIE approach applied to nitrogen gave a mean pore width of 0.57 nm; the CO2 distribution exhibited wider dispersion. Spherical model application to CO2 and diffusion limitations for nitrogen and argon were proposed as primary reasons for inconsistency. Immersion enthalpy revealed a sharp decrease in available area equivalent to a cut-off due to molecular exclusion when the accessible surface was assessed against probe kinetic diameter. Mean pore width was identified as 0.58 ± 0.02 nm, endorsing the underlying assumptions for the nitrogen-based AIE approach. A comparison of the zero-coverage isosteric heat of adsorption for various non-polar adsorptives by the porous test sample was compared with the same adsorptives in contact with a non-porous reference adsorbent, leading to an energy ratio or adsorption enhancement factor. A linear relationship between the energy ratio and probe kinetic diameter indicated a primary pore size at 0.59 nm. The advantage of this enthalpy, model-independent methods over AIE were due to no assumptions regarding probe molecular shape, and no assumptions for pore shape and/or connectivity.

Immobilized Microalgae for Nutrient Recovery from Source Separated Urine

Shortages in supply of nutrients and freshwater for a growing human population are critical global issues. Traditional centralized sewage treatment can prevent eutrophication and provide sanitation, but is neither efficient nor sustainable in terms of water and resources. Source separation of household wastes, combined with decentralized resource recovery, presents a novel approach to solve these issues. Urine contains within 1 % of household waste water up to 80 % of the nitrogen (N) and 50 % of the phosphorus (P). Since microalgae are efficient at nutrient uptake, growing these organisms in urine might be a promising technology to concomitantly clean urine and produce valuable biomass containing the major plant nutrients. While state-of-the-art suspension systems for algal cultivation have mayor shortcomings in their application, immobilized cultivation on Porous Substrate Photobioreactors (PSBRs) might be a feasible alternative. The aim of this study was to develop a robust process for nutrient recovery from minimally diluted human urine using microalgae on PSBRs. The green alga Desmodesmus abundans strain CCAC 3496 was chosen for its good growth, after screening 96 algal strains derived from urine-specific isolations and culture collections. Treatment of urine, 1:1 diluted with tap water and without addition of nutrients, was performed at a light intensity of 600 μmol photons m-2 s-1 with 2.5 % CO2 and at pH 6.5. A growth rate of 7.2 g dry weight m-² day-1 and removal efficiencies for N and P of 13.1 % and 94.1 %, respectively, were determined. Pre-treatment of urine with activated carbon was found to eliminate possible detrimental effects of pharmaceuticals. These results provide a basis for further development of the technology at pilot-scale. If found to be safe in terms human and environmental health, the biomass produced from three persons could provide the P for annual production of 31 kg wheat grain and 16 kg soybean, covering the caloric demand in food for almost one month of the year for such a household. In combination with other technologies, PSBRs could thus be applied in a decentralized resource recovery system, contributing to locally close the link between sanitation and food production.