Geochemistry at DSDP Hole 69-504B

Cores from Deep Sea Drilling Project Holes 501, 504B and 505B have an unusual near-vein zonation in basalts. Megascopically, zonation occurs as differently colored strips and zones whose typical thickness does not exceed 6 to 7 cm. Microscopically, the color of zones depends on variably colored clay minerals which are the products of low-temperature hydrothermal alteration in basalt. These differently colored zones form the so called "oxidative" type of alteration of basalts. Another "background," or, less precisely termed, "non-oxidative," type of alteration in basalts is characterized by large-scale, homogeneous replacement of olivine, and filling of vesicles and cracks by an olive-brown or olive-green clay mineral. The compositions of clay minerals of the "background" type of alteration, as well as the composition of co-existing titanomagnetites, were determined with an electron microprobe. There are sharp maxima in potassium and iron content, and minima in alumina, silica, and magnesia in clay minerals in the colored zones near veins. Coloring of clay and rock-forming minerals by iron hydroxides and a decrease of the amount of titanomagnetite, which apparently was the source of redeposited iron, occur frequently in colored zones. We assume that the large-scale "background" alteration in the basalts occurred under the effect of pore waters slowly penetrating through bottom sediments. Faulting can facilitate access of fresh sea water to basalts; thus above the general homogeneous background arise zones of "oxidative" alteration along fractures in basalts. The main factors controlling these processes are time (age of basalt), grain size, temperature, thickness of sedimentary cover, and heat flow.

d18O, lithologies, mineralogy and determination of temperature and depth of formation of DSDP Site 69-504 siliceous rocks

Seven opal-CT-rich and five quartz-rich porcellanites and cherts from Site 504 have a range in oxygen-isotope values of 24.4 and 29.4 per mil. In opal-CT rocks, d18O becomes larger with sub-bottom depth and with age. Quartz-rich rocks do not show these trends. Boron, in general, increases with decreasing d18O for porcellanites and cherts considered together, supporting the conclusion that boron is incorporated within the quartz crystal structure during precipitation of the SiO2. Silicification of the chalks at Site 504 began 1 m.y. ago - that is, 5 m.y. after sedimentation commenced on the oceanic crust. Temperatures of chert formation determined from oxygen-isotope compositions reflect diagenetic temperatures rather than bottom-water temperatures, and are comparable to temperatures of formation determined by down-hole measurements. Opal-A in the chalks began conversion to opal-CT when a temperature of 50°C was reached in the sediment column. Conversion of opal-CT to quartz started at 55 °C. Silicification occurred over a stratigraphic thickness of about 10 meters when the temperature at the top of the 10 meters reached about 50°C. It took about 250,000 years to complete the silica transformation within each 10-meter interval of sediment at Site 504. Quartz formed over a stratigraphic range of at least 30 meters, at temperatures of about 54 to 60°C. The time and temperatures of silicification of Site 504 rocks are more like those at continental margins than those in deep-sea, open-ocean deposits.

Geochemistry of felsic rocks and minerals of ODP Hole 135-841B

A felsic volcanic series (605-825 mbsf) overlain by upper Eocene shallow-water sediments (500-605 mbsf) and basalticandesitic sills that intruded into sediments of Holocene to Miocene age (0-500 mbsf) was drilled in the forearc region of the Lau Basin at a water depth of 4810 m. The volcanic sequence at Site 841 includes altered and mineralized calc-alkaline rhyolites and dacites, dacitic tuffs, lapilli tuffs, flow breccias, and welded tuffs. These rocks formed subaerially or in a very shallow-water environment suffering a subsidence of >5000 m since Eocene times. Calculations of gains and losses of the major components during alteration show most pronounced changes in the uppermost 70 m of the volcanic sequence. Here, Al, Fe, Mg, and K are enriched, whereas Si and Na are strongly depleted. Illite, vermiculite, chlorite, and hematite predominate in this part of the hole. Throughout the section, quartz, plagioclase, kaolinite, and calcite are present. Sulfide mineralization (up to 10 vol%) consisting mainly of disseminated pyrite (with minor pyrrhotite inclusions) and marcasite together with minor amounts of chalcopyrite is pervasive throughout. Locally, a few sulfide-bearing quartz-carbonate veins as well as Ti-amphibole replacement by rutile and then by pyrite were observed. Strong variations in the As content of sulfides (from 0 to 0.69 wt%) from the same depth interval and local enrichments of Co, Ni, and Cu in pyrite are interpreted to result from fluctuations in fluid composition. Calculations of oxygen and sulfur fugacities indicate that fO2 and fS2 were high at the top and lower at the bottom of the sequence. Sulfur isotope determinations on separated pyrite grains from two samples give d34S values of +6.4ë and +8.4ë, which are close to those reported from Kuroko and Okinawa Trough massive sulfide deposits and calc-alkaline volcanic rocks of the Japanese Ryukyu Island Arc. Calculated chlorite formation temperatures of 265°-290°C at the top of the sequence are consistent with minimum formation temperatures of fluid inclusions in secondary quartz, revealing a narrow range of 270°-297°C. Chlorite formation temperatures are constant downhole and do not exceed 300°C. The presence of marcasite and 4C-type pyrrhotite indicates a formation temperature of <= 250°C. At a later stage, illite was formed at the top of the volcanic series at temperatures well below 200°C.

Petrology and geochemistry of silicified upper Miocene chalk at DSDP Site 69-504

Chert, Porcellanite, and other silicified rocks formed in response to high heat flow in the lower 50 meters of 275 meters of sediments at Deep Sea Drilling Project Site 504, Costa Rica Rift. Chert and Porcellanite partly or completely replaced upper Miocene chalk and limestone. Silicified rock occurs as nodules, laminae, stringers, and casts of burrows, and consists of quartz and opal-CT in varying amounts, associated with secondary calcite. The secondary silica was derived from dissolution of opal-A (biogenic silica), mostly diatom frustules and radiolarian tests. Temperature data obtained at the site indicate that transformation of opal-A to opal-CT began at about 50°C, and transformation from opal-CT to quartz at about 55°C. Quartz is most abundant close to basement basalts. These silica transformations occurred over the past 1 m.y., and took place so rapidly that there was incomplete ordering of opal-CT before transformation to quartz; opal-CT formed initially with an uncommonly wide d spacing. Quartz shows poor crystallinity. Chemical data show that the extensively silicified rocks consist of over 96% SiO2; in these rocks, minor and trace elements decreased greatly, except for boron, which increased. Low Al2O3 and TiO2 contents in all studied rocks preclude the presence of significant volcanic or terrigenous detritus. Mn content increases with depth, perhaps reflecting contributions from basalts or hydrothermal solutions. Comparisons with cherts from oceanic plateaus in the central Pacific point to a more purely biogenic host sediment for the Costa Rica Rift cherts, more rapid precipitation of quartz, and formation nearer a spreading center. Despite being closer to continental sources of ash and terrigenous detritus, Costa Rica Rift cherts have lower Al2O3, Fe2O3, and Mn concentrations.