An Asymptotic Solution for Surface Fields on a Dielectric-Coated Circular Cylinder with an Effective Impedance Boundary Condition.

Reverberation chambers are well known for providing a random-like electric field distribution. Detection of directivity or gain thereof requires an adequate procedure and smart post-processing. In this paper, a new method is proposed for estimating the directivity of radiating devices in a reverberation chamber (RC). The method is based on the Rician K-factor whose estimation in an RC benefits from recent improvements. Directivity estimation relies on the accurate determination of the K-factor with respect to a reference antenna. Good agreement is reported with measurements carried out in near-field anechoic chamber (AC) and using a near-field to far-field transformation.

Exact solution for the conjugate fluid-fluid problem in the thermal entrance region of laminar counterflow heat exchangers

A generalized Lévêque solution is presented for the conjugate fluid–fluid problem that arises in the thermal entrance region of laminar counterflow heat exchangers. The analysis, carried out for constant property fluids, assumes that the Prandtl and Peclet numbers are both large compared to unity, and neglects axial conduction both in the fluids and in the plate, assumed to be thermally thin. Under these conditions, the thermal entrance region admits an asymptotic self-similar description where the temperature varies as a power ϳ of the axial distance, with the particularity that the self-similarity exponent must be determined as an eigenvalue by solving a transcendental equation arising from the requirement of continuity of heat fluxes at the heat conducting wall. Specifically, the analysis reveals that j depends only on the lumped parameter ƙ = (A2/A1)1/3 (α1/α2)1/3(k2/k1), defined in terms of the ratios of the wall velocity gradients, A, thermal diffusivities, α i, and thermal conductivities,k i, of the fluids entering, 1, and exiting, 2, the heat exchanger. Moreover, it is shown that for large (small) values of K solution reduces to the classical first (second) Lévêque solution. Closed-form analytical expressions for the asymptotic temperature distributions and local heat-transfer rate in the thermal entrance region are given and compared with numerical results in the counterflow parallel-plate configuration, showing very good agreement in all cases.

Transferencia inalámbrica de energía

El trabajo presentado en este documento se centra en la temática de la transferencia inalámbrica de energía, concretamente en aplicaciones de campo lejano, para llevar a cabo dicho trabajo nos centraremos en el diseño, implementación y medición de una rectenna operando en la banda ISM concretamente a una frecuencia de 2.45GHz, el objetivo primordial de este trabajo será analizar que parámetros intervienen en la eficiencia de conversión en la etapa de RF-DC a fin de lograr la máxima eficiencia de conversión posible. Para llevar a cabo dicho análisis se emplearán herramientas informáticas, concretamente se hará uso del software AWR Microwave Office, a través del cual se realizarán simulaciones SourcePull a fin de determinar la impedancia óptima de entrada que se le debe presentar a la etapa rectificadora RF-DC para conseguir la máxima eficiencia de conversión, una vez realizadas dichas pruebas se implementará físicamente un circuito rectenna a través del cual realizar medidas de SourcePull mediante un Wide Matching Range Slide Screw Tuner de MAURY MICROWAVE para cotejar las posibles diferencias con los resultados obtenidos en las simulaciones. Tras la fase de pruebas SourcePull se extrapolará una red de entrada en base a los datos obtenidos en las mediciones anteriores y se diseñará y fabricará un circuito rectenna con máxima eficiencia de conversión para un conjunto de valores de potencia de entrada de RF y carga de DC, tras lo cual se analizará la eficiencia del circuito diseñado para diferentes valores de potencia de RF de entrada y carga de DC. Como elemento rectificador emplearemos en nuestro trabajo el diodo Schottky HSMS-2820, los diodos Schottky se caracterizan por tener tiempos de conmutación relativamente bajos y pérdidas en directa reducidas los cual será fundamental a la hora de trabajar con niveles reducidos de potencia de RF de entrada, para implementar el circuito se empleará un substrato FR4 con espesor de 0.8mm para disminuir en la mayor medida posible las pérdidas introducidas por el dieléctrico, se analizarán diferentes posibilidades a la hora de implementar el filtro de RF a la salida del diodo rectificador y finalmente se optará por el empleo de un stub radial ya que será este el que mejor ancho de banda nos proporcione. Los resultados simulados se compararán con los resultados medidos sobre el circuito rectenna para determinar la similitud entre ambos. ABSTRACT. The work presented in this paper focuses on the issue of wireless transfer of energy, particularly applied to far-field applications, to carry out this work we focus on the design, implementation and measurement of a rectenna operating in the ISM band specifically at a frequency of 2.45GHz, the primary objective of this study is to analyze any parameter involved in the RF-DC conversion efficiency in order to achieve the maximum conversion efficiency as possible. Computer analysis tools will be used, particularly AWR Microwave Office software, in order to carry out SourcePull simulations to determine the optimal input impedance which must be presented to the rectifier stage for maximum conversion efficiency, once obtained, a rectenna circuit will be implemented to compute SourcePull measurements, and finally simulated results will be compared to measured results. Once obtained the result, an input network impedance is extrapolated based on data from previous measurements to design and implement a rectenna circuit with high conversion efficiency for a set of RF input power and DC load values , after that, the designed circuit efficiency will be analyzed for different values of RF input power and DC load. In this work a HSMS-2820 Schottky diode will be used as the rectifier , Schottky diodes are characterized by relatively low switching times and reduced direct losses, that properties will be essential when working with low RF input power levels , to implement the circuit a FR4 substrate with 0.8mm thickness is used to reduce as much as possible the dielectric losses, different possibilities to implement the RF filter to the output of the rectifier diode will be analyzed, finally we will opt for the use of a radial stub as this will provide the best bandwidth possible. The simulated results are compared with the results measured on the rectenna circuit to determine the similarity between them.

Oxide Semiconductors For Organic Opto-electronic Devices

Development of transparent oxide semiconductors (TOS) from Earth-abundant materials is of great interest for cost-effective thin film device applications, such as solar cells, light emitting diodes (LEDs), touch-sensitive displays, electronic paper, and transparent thin film transistors. The need of inexpensive or high performance electrode might be even greater for organic photovoltaic (OPV), with the goal to harvest renewable energy with inexpensive, lightweight, and cost competitive materials. The natural abundance of zinc and the wide bandgap ($sim$3.3 eV) of its oxide make it an ideal candidate. In this dissertation, I have introduced various concepts on the modulations of various surface, interface and bulk opto-electronic properties of ZnO based semiconductor for charge transport, charge selectivity and optimal device performance. I have categorized transparent semiconductors into two sub groups depending upon their role in a device. Electrodes, usually 200 to 500 nm thick, optimized for good transparency and transporting the charges to the external circuit. Here, the electrical conductivity in parallel direction to thin film, i.e bulk conductivity is important. And contacts, usually 5 to 50 nm thick, are optimized in case of solar cells for providing charge selectivity and asymmetry to manipulate the built in field inside the device for charge separation and collection. Whereas in Organic LEDs (OLEDs), contacts provide optimum energy level alignment at organic oxide interface for improved charge injections. For an optimal solar cell performance, transparent electrodes are designed with maximum transparency in the region of interest to maximize the light to pass through to the absorber layer for photo-generation, plus they are designed for minimum sheet resistance for efficient charge collection and transport. As such there is need for material with high conductivity and transparency. Doping ZnO with some common elements such as B, Al, Ga, In, Ge, Si, and F result in n-type doping with increase in carriers resulting in high conductivity electrode, with better or comparable opto-electronic properties compared to current industry-standard indium tin oxide (ITO). Furthermore, improvement in mobility due to improvement on crystallographic structure also provide alternative path for high conductivity ZnO TCOs. Implementing these two aspects, various studies were done on gallium doped zinc oxide (GZO) transparent electrode, a very promising indium free electrode. The dynamics of the superimposed RF and DC power sputtering was utilized to improve the microstructure during the thin films growth, resulting in GZO electrode with conductivity greater than 4000 S/cm and transparency greater than 90 %. Similarly, various studies on research and development of Indium Zinc Tin Oxide and Indium Zinc Oxide thin films which can be applied to flexible substrates for next generation solar cells application is presented. In these new TCO systems, understanding the role of crystallographic structure ranging from poly-crystalline to amorphous phase and the influence on the charge transport and optical transparency as well as important surface passivation and surface charge transport properties. Implementation of these electrode based on ZnO on opto-electronics devices such as OLED and OPV is complicated due to chemical interaction over time with the organic layer or with ambient. The problem of inefficient charge collection/injection due to poor understanding of interface and/or bulk property of oxide electrode exists at several oxide-organic interfaces. The surface conductivity, the work function, the formation of dipoles and the band-bending at the interfacial sites can positively or negatively impact the device performance. Detailed characterization of the surface composition both before and after various chemicals treatment of various oxide electrode can therefore provide insight into optimization of device performance. Some of the work related to controlling the interfacial chemistry associated with charge transport of transparent electrodes are discussed. Thus, the role of various pre-treatment on poly-crystalline GZO electrode and amorphous indium zinc oxide (IZO) electrode is compared and contrasted. From the study, we have found that removal of defects and self passivating defects caused by accumulation of hydroxides in the surface of both poly-crystalline GZO and amorphous IZO, are critical for improving the surface conductivity and charge transport. Further insight on how these insulating and self-passivating defects cause charge accumulation and recombination in an device is discussed. With recent rapid development of bulk-heterojunction organic photovoltaics active materials, devices employing ZnO and ZnO based electrode provide air stable and cost-competitive alternatives to traditional inorganic photovoltaics. The organic light emitting diodes (OLEDs) have already been commercialized, thus to follow in the footsteps of this technology, OPV devices need further improvement in power conversion efficiency and stable materials resulting in long device lifetimes. Use of low work function metals such as Ca/Al in standard geometry do provide good electrode for electron collection, but serious problems using low work-function metal electrodes originates from the formation of non-conductive metal oxide due to oxidation resulting in rapid device failure. Hence, using low work-function, air stable, conductive metal oxides such as ZnO as electrons collecting electrode and high work-function, air stable metals such as silver for harvesting holes, has been on the rise. Devices with degenerately doped ZnO functioning as transparent conductive electrode, or as charge selective layer in a polymer/fullerene based heterojunction, present useful device structures for investigating the functional mechanisms within OPV devices and a possible pathway towards improved air-stable high efficiency devices. Furthermore, analysis of the physical properties of the ZnO layers with varying thickness, crystallographic structure, surface chemistry and grain size deposited via various techniques such as atomic layer deposition, sputtering and solution-processed ZnO with their respective OPV device performance is discussed. We find similarity and differences in electrode property for good charge injection in OLEDs and good charge collection in OPV devices very insightful in understanding physics behind device failures and successes. In general, self-passivating surface of amorphous TCOs IZO, ZTO and IZTO forms insulating layer that hinders the charge collection. Similarly, we find modulation of the carrier concentration and the mobility in electron transport layer, namely zinc oxide thin films, very important for optimizing device performance.

Hydrogeophysical characterization of anisotropy in the Biscayne Aquifer using geophysical methods

The anisotropy of the Biscayne Aquifer which serves as the source of potable water for Miami-Dade County was investigated by applying geophysical methods. Electrical resistivity imaging, self potential and ground penetration radar techniques were employed in both regional and site specific studies. In the regional study, electrical anisotropy and resistivity variation with depth were investigated with azimuthal square array measurements at 13 sites. The observed coefficient of electrical anisotropy ranged from 1.01 to 1.36. The general direction of measured anisotropy is uniform for most sites and trends W-E or SE-NW irrespective of depth. Measured electrical properties were used to estimate anisotropic component of the secondary porosity and hydraulic anisotropy which ranged from 1 to 11% and 1.18 to 2.83 respectively. 1-D sounding analysis was used to models the variation of formation resistivity with depth. Resistivities decreased from NW (close to the margins of the everglades) to SE on the shores of Biscayne Bay. Porosity calculated from Archie's law, ranged from 18 to 61% with higher values found along the ridge. Higher anisotropy, porosities and hydraulic conductivities were on the Atlantic Coastal Ridge and lower values at low lying areas west of the ridge. The cause of higher anisotropy and porosity is attributed to higher dissolution rates of the oolitic facies of the Miami Formation composing the ridge. The direction of minimum resistivity from this study is similar to the predevelopment groundwater flow direction indicated in published modeling studies. Detailed investigations were carried out to evaluate higher anisotropy at West Perrine Park located on the ridge and Snapper Creek Municipal well field where the anisotropy trend changes with depth. The higher anisotropy is attributed to the presence of solution cavities oriented in the E-SE direction on the ridge. Similarly, the change in hydraulic anisotropy at the well field might be related to solution cavities, the surface canal and groundwater extraction wells.^

Analysis of the lateral diffuse metal-oxide semiconductor (LDMOS) power amplifier for cellular base stations

The primary purpose of this thesis was to present a theoretical large-signal analysis to study the power gain and efficiency of a microwave power amplifier for LS-band communications using software simulation. Power gain, efficiency, reliability, and stability are important characteristics in the power amplifier design process. These characteristics affect advance wireless systems, which require low-cost device amplification without sacrificing system performance. Large-signal modeling and input and output matching components are used for this thesis. Motorola's Electro Thermal LDMOS model is a new transistor model that includes self-heating affects and is capable of small-large signal simulations. It allows for most of the design considerations to be on stability, power gain, bandwidth, and DC requirements. The matching technique allows for the gain to be maximized at a specific target frequency. Calculations and simulations for the microwave power amplifier design were performed using Matlab and Microwave Office respectively. Microwave Office is the simulation software used in this thesis. The study demonstrated that Motorola's Electro Thermal LDMOS transistor in microwave power amplifier design process is a viable solution for common-source amplifier applications in high power base stations. The MET-LDMOS met the stability requirements for the specified frequency range without a stability-improvement model. The power gain of the amplifier circuit was improved through proper microwave matching design using input/output-matching techniques. The gain and efficiency of the amplifier improve approximately 4dB and 7.27% respectively. The gain value is roughly .89 dB higher than the maximum gain specified by the MRF21010 data sheet specifications. This work can lead to efficient modeling and development of high power LDMOS transistor implementations in commercial and industry applications.

Análise comparativa da imunoexpressão do IMP-3 e Ki-67 em queilites actínicas e carcinoma epidermóide de lábio inferior

Epithelial changes observed in actinic cheilitis (AC) and squamous cell carcinoma of the lower lip (LLSCC) are mainly caused by chronic exposure to ultraviolet rays (UV) and are studied using different immunohistochemical markers trying to evaluate the process of carcinogenesis. The objective of this study was to comparatively evaluate the expression of Ki-67 proteins and IMP-3 in AC and LLSCC to contribute with additional information on carcinogenesis in lower lip. A total of 33 cases of AC and 33 cases of LLSCC were studied, analyzed the clinical and pathological features and immunostaining of Ki-67 and IMP-3. Immunohistochemical analysis of Ki-67 was made through the determination of the proliferation index (PI) and subsequent classification of the cases according to the scores: 0 (0% positive cells) +1 (≤30%) + 2 (> 30% and ≤60%) and +3 (> 60%). For statistical tests cases were classified as unmarked (score 0), low expression (score +1) and high expression (scores +2 and +3). For the expression of IMP-3, the percentage of immunostained epithelial cells was established, and assigned scores: 0 (corresponding to 0%), +1 (up to 30% of positive cells); +2 (From 30% to 60% of immunostained cells) and +3 (over 60% of positive cells). Statistical tests chi-square test, Mann-Whitney and Wilcoxon were used. The significance level was 5%. Most AC chaos was male (78.8%) with mean age of 50 years and cases of LLSCC also were male (69.89%) with an average of 62 years. The Ki-67 was expressed in all cases of AC and in cases of LLSCC, predominantly in the two injuries the score 2, corresponding to 81.8% of cases in ACs and 54.5% in the CELI. The expression of IMP-3 in ACs occurred in 72.7% of cases, predominantly in 36.3% of LLSCC cases score 1. Already in the IMP-3 was expressed in 60.6% of cases, especially in 27.3% of the score of the cases 3. These results allow us to conclude that the expression of IMP3 and proliferative activity are early events in carcinogenesis independently lower lip state of change.

Visibilidad y percepción en la construcción de un paisaje Prehistórico. El caso de Calviá (Mallorca, Islas Baleares)

El presente trabajo se centra en el estudio del papel que juega el control visual del espacio en las prácticas sociales de las comunidades prehistóricas. Este trabajo se articula a partir de un estudio de caso, el término municipal de Calviá, situado en el sureste de la isla de Mallorca, para analizar las diferentes formas de monumentalidad arquitectónica y cómo estas se constituyen cómo un punto de referencia social dentro del paisaje. Partiendo de una amplia horquilla temporal, que abarcaría el Bronce Naviforme (1550-850 AC), el período Talayótico (850-550 AC) y el Postalayótico (550-123 AC), se propone analizar los cambios y pervivencias en la construcción del paisaje, a través de estrategias de visibilidad, percepción y movimiento alrededor de los monumentos arquitectónicos. A través de la perspectiva de la Arqueología del Paisaje y mediante el uso de Sistemas de Información Geográfica (SIG) se propone un análisis de tendencias a largo plazo en la configuración social de un paisaje.

Indirect Effects of Parental Coping on Children’s Psychosocial Adjustment in the Context of Pediatric Cancer

Thesis (Ph.D.)--University of Washington, 2016-08

Avian influenza in Australia: a summary of 5 years of wild bird surveillance

BackgroundAvian influenza viruses (AIVs) are found worldwide in numerous bird species, causing significant disease in gallinaceous poultry and occasionally other species. Surveillance of wild bird reservoirs provides an opportunity to add to the understanding of the epidemiology of AIVs. MethodsThis study examined key findings from the National Avian Influenza Wild Bird Surveillance Program over a 5-year period (July 2007-June 2012), the main source of information on AIVs circulating in Australia. ResultsThe overall proportion of birds that tested positive for influenza A via PCR was 1.90.1%, with evidence of widespread exposure of Australian wild birds to most low pathogenic avian influenza (LPAI) subtypes (H1-13, H16). LPAI H5 subtypes were found to be dominant and widespread during this 5-year period. ConclusionGiven Australia's isolation, both geographically and ecologically, it is important for Australia not to assume that the epidemiology of AIV from other geographic regions applies here. Despite all previous highly pathogenic avian influenza outbreaks in Australian poultry being attributed to H7 subtypes, widespread detection of H5 subtypes in wild birds may represent an ongoing risk to the Australian poultry industry.

Sick Boy

This poetry collection explores the concepts of addiction and redemption. It does so through a series of vignette-style poems set in the Baltimore and DC area at the height of the heroin epidemic in the United States. Split into three parts, the first addresses the narrator’s initial drug use, the second follows the narrator at the strongest and least hopeful point of his addiction, and the third examines, through various scenes, the narrator’s attempts to find a life free from the confines of addiction. Although dealing with subject matter derived from dark and unfortunate circumstances, the narrator’s heroin addiction serves merely as a catalyst for the various situations that force the narrator to develop emotionally and grow even when trapped in the seemingly inescapable confines of addiction.

Rutting performance of asphalt pavements

Cold in-place recycling (CIR) and cold central plant recycling (CCPR) of asphalt concrete (AC) and/or full-depth reclamation (FDR) of AC and aggregate base are faster and less costly rehabilitation alternatives to conventional reconstruction for structurally distressed pavements. This study examines 26 different rehabilitation projects across the USA and Canada. Field cores from these projects were tested for dynamic modulus and repeated load permanent deformation. These structural characteristics are compared to reference values for hot mix asphalt (HMA). A rutting sensitivity analysis was performed on two rehabilitation scenarios with recycled and conventional HMA structural overlays in different climatic conditions using the Mechanistic Empirical Pavement Design (MEPDG). The cold-recycled scenarios exhibited performance similar to that of HMA overlays for most cases. The exceptions were the cases with thin HMA wearing courses and/or very poor cold-recycled material quality. The overall conclusion is that properly designed CIR/FDR/CCPR cold-recycled materials are a viable alternative to virgin HMA materials.

Caracterização de compósitos Nb-20%cu obtidos por moagem de alta energia e sinterizados por fase líquida

In this work, was studied the formation of a composite of the refractory metal niobium with copper, through the process of high-energy milling and liquid phase sintering. The HEM can be used to synthesize composite powders with high homogeneity and fine size particle distribution. It may also produce the solid solubility in immiscible systems such as Nb-Cu, or extend the solubility of systems with limited solubility. Therefore, in the immiscible system Cu-Nb, the high-energy milling was successfully used to obtain the composite powder particles. Initially, the formation of composite particles during the HEM and the effect of preparation technique on the microstructure of the material was evaluated. Four loads of Nb and Cu powders containing 20%wt Cu were synthesized by MAE in a planetary type ball mill under different periods of grinding. The influence of grinding time on the metal particles is evaluated during the process by the withdrawal of samples at intermediate times of milling. After compaction under different forces, the samples were sintered in a vacuum furnace. The liquid phase sintering of these samples prepared by HEM produced a homogeneous and fine grained. The composite particles forming the sintered samples are the addition of a hard phase (Nb) with a high melting point, and a ductile phase (Cu) with low melting point and high thermal and electrical conductivities. Based on these properties, the Nb-Cu system is a potential material for many applications, such as electrical contacts, welding electrodes, coils for generating high magnetic fields, heat sinks and microwave absorbers, which are coupled to electronic devices. The characterization techniques used in this study, were laser granulometry, used to evaluate the homogeneity and particle size, and the X-ray diffraction, in the phase identification and to analyze the crystalline structure of the powders during milling. The morphology and dispersion of the phases in the composite powder particles, as well the microstructures of the sintered samples, were observed by scanning electron microscopy (SEM). Subsequently, the sintered samples are evaluated for density and densification. And finally, they were characterized by techniques of measuring the electrical conductivity and microhardness, whose properties are analyzed as a function of the parameters for obtaining the composite

Obtenção de pós de tântalo metálico a partir da redução aluminotérmica com ignição a plasma

Metallic tantalum has a high commercial value due to intrinsic properties like excellent ductility, corrosion resistance, high melt and boiling points and good electrical and thermal conductivities. Nowadays, it is mostly used in the manufacture of capacitors, due to excellent dielectric properties of its oxides. In the nature, tantalum occurs in the form of oxide and it is extracted mainly from tantalite-columbite ores. The tantalum is usually produced by the reduction of its oxide, using reductants like carbon, silicon, calcium, magnesium and aluminum. Among these techniques, the aluminothermic reduction has been used as the industrial method to produce niobium, tantalum and their alloys, due to the easy removal of the Al and Al2O3 of the system, easing further refining. In conventional aluminothermic reduction an electrical resistance is used to trigger the reaction. This reaction self-propagates for all the volume of material. In this work, we have developed a novel technique of aluminothermic reduction that uses the hydrogen plasma to trigger the reaction. The results obtained by XRD, SEM and EDS show that is possible to obtain a compound rich in tantalum through this technique of aluminothermic reduction in the plasma reactor