Queen's EAP Steering Committee Annual Report, 2007/2008

The 2007/2008 annual report of the Queen's EAP Steering Committee.

Insight into the key aspects of the regeneration process in the NOx storage reduction (NSR) reaction probed using fast transient kinetics coupled with isotopically labelled (NO)-N-15 over Pt and Rh-containing Ba/Al2O3 catalysts

For the first time, the coupling of fast transient kinetic switching and the use of an isotopically labelled reactant (15NO) has allowed detailed analysis of the evolution of all the products and reactants involved in the regeneration of a NOx storage reduction (NSR) material. Using realistic regeneration times (ca. 1 s) for Pt, Rh and Pt/Rh-containing Ba/Al2O3 catalysts we have revealed an unexpected double peak in the evolution of nitrogen. The first peak occurred immediately on switching from lean to rich conditions, while the second peak started at the point at which the gases switched from rich to lean. The first evolution of nitrogen occurs as a result of the fast reaction between H2 and/or CO and NO on reduced Rh and/or Pt sites. The second N2 peak which occurs upon removal of the rich phase can be explained by reaction of stored ammonia with stored NOx, gas phase NOx or O2. The ammonia can be formed either by hydrolysis of isocyanates or by direct reaction of NO and H2.

The study highlights the importance of the relative rates of regeneration and storage in determining the overall performance of the catalysts. The performance of the monometallic 1.1%Rh/Ba/Al2O3 catalyst at 250 and 350 °C was found to be dependent on the rate of NOx storage, since the rate of regeneration was sufficient to remove the NOx stored in the lean phase. In contrast, for the monometallic 1.6%Pt/Ba/Al2O3 catalyst at 250 °C, the rate of regeneration was the determining factor with the result that the amount of NOx stored on the catalyst deteriorated from cycle to cycle until the amount of NOx stored in the lean phase matched the NOx reduced in the rich phase. On the basis of the ratio of exposed metal surface atoms to total Ba content, the monometallic 1.6%Pt/Ba/Al2O3 catalyst outperformed the Rh-containing catalysts at 250 and 350 °C even when CO was used as a reductant.

Effect of the carburization of MoO3-based catalysts on the activity for butane hydroisomerization

Catalysts based on molybdena (MoO3) reduced at mild temperatures are highly active and selective for the hydroisomerization of alkanes: however, further catalyst development has been hampered by the structural complexity of the material and the controversy regarding the nature of the active phase. The present work is aimed at determining the relationship between the content of carbon present in an oxycarbide phase and the activity for n-butane hydroisomerization. A series of temperature-programmed oxidation (TPO) and temporal analysis of product (TAP) data showed that the oxycarbidic carbon content is not related to the activity of the sample for the isomerization of n-butane to isobutane. The formation of a carbon-containing phase is, therefore, not crucial to obtain an active catalyst. This study also highlights the capability of the multi-pulse TAP technique to investigate structure-activity relationships over materials with readily variable atomic composition. (C) 2008 Elsevier B.V. All rights reserved.

Hydrogenation/hydrogenolysis of disulfides using sulfided Ni/Mo catalysts

The mechanism of the hydrogenation/hydrogenolysis of dinitrodiphenyldisulfides using sulfided NiMo/ gamma Al2O3 catalysts has been examined in detail. Although two routes are possible, the major pathway involves an initial S-S bond cleavage followed by reduction of the nitro group. Importantly, the disulfide hydrogenolysis occurs in the absence of the catalyst with the role of the catalyst thought to be to activate the hydrogen and trap the cleaved intermediate as well as facilitate the reduction of the nitro group. Monitoring the mass balance throughout the reaction demonstrates the difficulty in measuring intrinsic kinetics for gas-liquid-solid reactions. Although the mass balance is restored at the end of the reaction, up to 45% of the substrate/products is found to be adsorbed on the catalyst during the reaction. (c) 2008 Elsevier B.V. All rights reserved.

Acylation of sulfonamines using silica grafted 1-butyl-3-(3-triethoxysilylpropyl)-4,5-dihydroimidazolium ionic liquids as catalysts

Heterogeneous immobilized ionic liquid catalysts were prepared via grafting of 1,3-dimethyl-3-(3-triethoxysilylpropyl)-imidazolium tetrafluoroborate or bist{(trifluoromethyl)sulfonyl} imide ([NTf2](-)) on silica supports with different surfaces and pore size. In addition to the adsorption-desorption isotherms of nitrogen at -196C, the catalysts were characterized by TG-DTA, XPS, DRIFTS, DR-UV-vis, NMR, and XRD techniques. The catalytic behavior was checked in the acylation of three different sulfonamines: benzenesulfonamine, p-nitrobenzene-sulfonamine, and p-methoxybenzene-sulfonamine with acetic acid, acetic anhydride and maleic anhydride. These tests confirmed the acid Lewis properties of these catalysts. (c) 2007 Elsevier B.V. All rights reserved.

CO multipulse TAP studies of 2% Pt/CeO2 catalyst: Influence of catalyst pretreatment and temperature on the number of active sites observed

CO multipulse temporal analysis of products (TAP) experiments were used to characterize a ceria-supported platinum catalyst after various oxidative and reductive pretreatments using O-2, H2O, CO2, and H-2. Based on the amount of CO consumed, using the final CO-saturated catalyst composition as the common state point, the oxidatively pretreated catalyst could be described using a general scale. From a kinetic analysis of the CO multipulse responses, two kinetic regimes corresponding to two types of active sites could be identified. As the temperature was raised, the number of the most active sites did not change while the amount of the less active site increased. Comparison of the number of active sites determined from the TAP data reported herein with that determined by a previous steady-state isotope transient kinetic analysis experiment showed excellent agreement. This correlation indicates that the (very fast response) TAP experiments can provide information regarding the number and type of active sites that are relevant to a catalyst under real reaction conditions. (c) 2007 Elsevier Inc. All rights reserved.

A DFT study of the chain growth probability in Fischer-Tropsch synthesis

The chain growth probability (alpha value) is one of the most significant parameters in Fischer-Tropsch (FT) synthesis. To gain insight into the chain growth probability, we systematically studied the hydrogenation and C-C coupling reactions with different chain lengths on the stepped Co(0001) surface using density functional theory calculations. Our findings elucidate the relationship between the barriers of these elementary reactions and the chain length. Moreover, we derived a general expression of the chain growth probability and investigated the behavior of the alpha value observed experimentally. The high methane yield results from the lower chain growth rate for C-1 + C-1 coupling compared with the other coupling reactions. After C-1, the deviation of product distribution in FT synthesis from the Anderson-Schulz-Flory distribution is due to the chain length-dependent paraffin/olefin ratio. (C) 2008 Elsevier Inc. All rights reserved.

A quantitative determination of reaction mechanisms from density functional theory calculations: Fischer-Tropsch synthesis on flat and stepped cobalt surfaces

We systematically investigated the mechanism of the C-1 + C-1 coupling reactions using density functional theory. The activation energies of C-1 + C-1 coupling and carbon hydrogenation reactions on both flat and stepped surfaces were calculated and analyzed. Moreover, the coverages of adsorbed C-1 species were estimated, and the reaction rates of all possible C-1 + C-1 coupling pathways were quantitatively evaluated. The results suggest that the reactions of CH2 + CH2 and CH3 + C at steps are most likely to be the key C-1 + C-1 coupling steps in FT synthesis on Co catalysts. The reactions of C-2 + C-1 and C-3 + C-1 coupling also were studied; the results demonstrate that in addition to the pathways of RCH + CH2 and RCH2 + C, the coupling of RC + C and RC + CH also may contribute to the chain growth after C-1. (C) 2008 Elsevier Inc. All rights reserved.