Energy Efficiency Consideration in Electric Vehicle Transmission

This study is a survey of benefits and drawbacks of embedding a variable gearbox instead of a single reduction gear in electric vehicle powertrain from efficiency point of view. Losses due to a pair of spur gears meshing with involute teeth are modeled on the base of Coulomb’s law and fluid mechanics. The model for a variable gearbox is fulfilled and further employed in a complete vehicle simulation. Simulation model run for a single reduction gear then the results are taken as benchmark for other types of commonly used transmissions. Comparing power consumption, which is obtained from simulation model, shows that the extra load imposed by variable transmission components will shade the benefits of efficient operation of electric motor. The other accomplishment of this study is a combination of modified formulas that led to a new methodology for power loss prediction in gear meshing which is compatible with modern design and manufacturing technology.

Combination of pulsed corona discharge with TiO2 photocatalysis: verification of hypothesis

The oxidation potential of pulsed corona discharge concerning aqueous impurities is limited in respect to certain refractory compounds. This may be enhanced in combination of the discharge with catalysis/photocatalysis as developed in homogeneous gas-phase reactions. The objective of the work consists of testing the hypothesis of oxidation potential enhancement in combination of the discharge with TiO2 photocatalysis applied to aqueous solutions of refractory oxalate. Meglumine acridone acetate was included for meeting the practical needs. The experimental research was undertaken into oxidation of aqueous solutions under conditions of various target pollutant concentrations, pH and the pulse repetition rate with plain electrodes and the electrodes with TiO2 attached to their surface. The results showed no positive influence of the photocatalyst, the pollutants were oxidized with the rate identical within the accuracy of measurements. The possible explanation for the observed inefficiency may include low UV irradiance, screening effect of water and generally low oxidation rate in photocatalytic reactions. Further studies might include combination of electric discharge with ozone decomposition/radical formation catalysts.

Simulation of new p-type pixel strip detector with enhanced multiplication effect

This Master’s Thesis is dedicated to the simulation of new p-type pixel strip detector with enhanced multiplication effect. It is done for high-energy physics experiments upgrade such as Super Large Hadron Collider especially for Compact Muon Solenoid particle track silicon detectors. These detectors are used in very harsh radiation environment and should have good radiation hardness. The device engineering technology for developing more radiation hard particle detectors is used for minimizing the radiation degradation. New detector structure with enhanced multiplication effect is proposed in this work. There are studies of electric field and electric charge distribution of conventional and new p-type detector under reverse voltage bias and irradiation. Finally, the dependence of the anode current from the applied cathode reverse voltage bias under irradiation is obtained in this Thesis. For simulation Silvaco Technology Computer Aided Design software was used. Athena was used for creation of doping profiles and device structures and Atlas was used for getting electrical characteristics of the studied devices. The program codes for this software are represented in Appendixes.

Induction of Fos protein immunoreactivity by spinal cord contusion

The objective of the present study was to identify neurons in the central nervous system that respond to spinal contusion injury in the rat by monitoring the expression of the nuclear protein encoded by the c-fos gene, an activity-dependent gene, in spinal cord and brainstem regions. Rats were anesthetized with urethane and the injury was produced by dropping a 5-g weight from 20.0 cm onto the exposed dura at the T10-L1 vertebral level (contusion group). The spinal cord was exposed but not lesioned in anesthetized control animals (laminectomy group); intact animals were also subjected to anesthesia (intact control). Behavioral alterations were analyzed by Tarlov/Bohlman scores, 2 h after the procedures and the animals were then perfused for immunocytochemistry. The patterns of Fos-like immunoreactivity (FLI) which were site-specific, reproducible and correlated with spinal laminae that respond predominantly to noxious stimulation or injury: laminae I-II (outer substantia gelatinosa) and X and the nucleus of the intermediolateral cell column. At the brain stem level FLI was detected in the reticular formation, area postrema and solitary tract nucleus of lesioned animals. No Fos staining was detected by immunocytochemistry in the intact control group. However, detection of FLI in the group submitted to anesthesia and surgical procedures, although less intense than in the lesion group, indicated that microtraumas may occur which are not detected by the Tarlov/Bohlman scores. There is both a local and remote effect of a distal contusion on the spinal cord of rats, implicating sensory neurons and centers related to autonomic control in the reaction to this kind of injury.

Reduction of intraspecific aggression in adult rats by neonatal treatment with a selective serotonin reuptake inhibitor

Most studies suggest that serotonin exerts an inhibitory control on the aggression process. According to experimental evidence, this amine also influences growth and development of the nervous tissue including serotoninergic neurons. Thus, the possibility exists that increased serotonin availability in young animals facilitates a long-lasting effect on aggressive responses. The present study aimed to investigate the aggressive behavior of adult rats (90-120 days) treated from the 1st to the 19th postnatal day with citalopram (CIT), a selective serotonin reuptake inhibitor (20 mg/kg, sc, every 3 days). Aggressive behavior was induced by placing a pair of rats (matched by weight) in a box (20 x 20 x 20 cm), and submitting them to a 20-min session of electric footshocks (five 1.6-mA - 2-s current pulses, separated by a 4-min intershock interval). When compared to the control group (rats treated for the same period with equivalent volumes of saline solution), the CIT group presented a 41.4% reduction in the duration of aggressive response. The results indicate that the repeated administration of CIT early in life reduces the aggressive behavior in adulthood and suggest that the increased brain serotoninergic activity could play a role in this effect.

Lightweight, liquid-cooled, direct-drive generator for highpower wind turbines: motivation, concept, and performance

Thesis: A liquid-cooled, direct-drive, permanent-magnet, synchronous generator with helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit offers an excellent combination of attributes to reliably provide economic wind power for the coming generation of wind turbines with power ratings between 5 and 20MW. A generator based on the liquid-cooled architecture proposed here will be reliable and cost effective. Its smaller size and mass will reduce build, transport, and installation costs. Summary: Converting wind energy into electricity and transmitting it to an electrical power grid to supply consumers is a relatively new and rapidly developing method of electricity generation. In the most recent decade, the increase in wind energy’s share of overall energy production has been remarkable. Thousands of land-based and offshore wind turbines have been commissioned around the globe, and thousands more are being planned. The technologies have evolved rapidly and are continuing to evolve, and wind turbine sizes and power ratings are continually increasing. Many of the newer wind turbine designs feature drivetrains based on Direct-Drive, Permanent-Magnet, Synchronous Generators (DD-PMSGs). Being low-speed high-torque machines, the diameters of air-cooled DD-PMSGs become very large to generate higher levels of power. The largest direct-drive wind turbine generator in operation today, rated just below 8MW, is 12m in diameter and approximately 220 tonne. To generate higher powers, traditional DD-PMSGs would need to become extraordinarily large. A 15MW air-cooled direct-drive generator would be of colossal size and tremendous mass and no longer economically viable. One alternative to increasing diameter is instead to increase torque density. In a permanent magnet machine, this is best done by increasing the linear current density of the stator windings. However, greater linear current density results in more Joule heating, and the additional heat cannot be removed practically using a traditional air-cooling approach. Direct liquid cooling is more effective, and when applied directly to the stator windings, higher linear current densities can be sustained leading to substantial increases in torque density. The higher torque density, in turn, makes possible significant reductions in DD-PMSG size. Over the past five years, a multidisciplinary team of researchers has applied a holistic approach to explore the application of liquid cooling to permanent-magnet wind turbine generator design. The approach has considered wind energy markets and the economics of wind power, system reliability, electromagnetic behaviors and design, thermal design and performance, mechanical architecture and behaviors, and the performance modeling of installed wind turbines. This dissertation is based on seven publications that chronicle the work. The primary outcomes are the proposal of a novel generator architecture, a multidisciplinary set of analyses to predict the behaviors, and experimentation to demonstrate some of the key principles and validate the analyses. The proposed generator concept is a direct-drive, surface-magnet, synchronous generator with fractional-slot, duplex-helical, double-layer, non-overlapping windings formed from a copper conductor with a coaxial internal coolant conduit to accommodate liquid coolant flow. The novel liquid-cooling architecture is referred to as LC DD-PMSG. The first of the seven publications summarized in this dissertation discusses the technological and economic benefits and limitations of DD-PMSGs as applied to wind energy. The second publication addresses the long-term reliability of the proposed LC DD-PMSG design. Publication 3 examines the machine’s electromagnetic design, and Publication 4 introduces an optimization tool developed to quickly define basic machine parameters. The static and harmonic behaviors of the stator and rotor wheel structures are the subject of Publication 5. And finally, Publications 6 and 7 examine steady-state and transient thermal behaviors. There have been a number of ancillary concrete outcomes associated with the work including the following. X Intellectual Property (IP) for direct liquid cooling of stator windings via an embedded coaxial coolant conduit, IP for a lightweight wheel structure for lowspeed, high-torque electrical machinery, and IP for numerous other details of the LC DD-PMSG design X Analytical demonstrations of the equivalent reliability of the LC DD-PMSG; validated electromagnetic, thermal, structural, and dynamic prediction models; and an analytical demonstration of the superior partial load efficiency and annual energy output of an LC DD-PMSG design X A set of LC DD-PMSG design guidelines and an analytical tool to establish optimal geometries quickly and early on X Proposed 8 MW LC DD-PMSG concepts for both inner and outer rotor configurations Furthermore, three technologies introduced could be relevant across a broader spectrum of applications. 1) The cost optimization methodology developed as part of this work could be further improved to produce a simple tool to establish base geometries for various electromagnetic machine types. 2) The layered sheet-steel element construction technology used for the LC DD-PMSG stator and rotor wheel structures has potential for a wide range of applications. And finally, 3) the direct liquid-cooling technology could be beneficial in higher speed electromotive applications such as vehicular electric drives.

Use of conventional PCR and smear microscopy to diagnose pulmonary tuberculosis in the Amazonian rainforest area

The diagnostic usefulness of Ziehl-Neelsen (ZN)-stained sputum smears combined with conventional polymerase chain reaction (ZN/PCR) to amplify IS6110 region DNA extracted from ZN slides was evaluated. The objective was to verify if this association could improve tuberculosis (TB) diagnosis in patients at remote sites. The study was carried out in 89 patients with culture-confirmed pulmonary TB as defined by the Brazilian Manual for TB Treatment. The participants were recruited in a reference unit for TB treatment in Rondônia, a state in the Amazonian area in northern Brazil. ZN, PCR, and culture performed in the sputum samples from these patients were analyzed in different combinations (i.e., ZN plus PCR and ZN plus culture). The prevalence rates of pulmonary TB in these patients were 32.6 and 28.1% considering culture and ZN/PCR, respectively. The sensitivity and specificity of ZN/PCR were 86 and 93%, respectively. ZN/PCR was able to detect more TB cases than ZN alone. This method could offer a new approach for accurate tuberculosis diagnosis, especially in remote regions of the world where culture is not available.

Recognition of nucleic acids by metal ion complexes

Metal-ion-mediated base-pairing of nucleic acids has attracted considerable attention during the past decade, since it offers means to expand the genetic code by artificial base-pairs, to create predesigned molecular architecture by metal-ion-mediated inter- or intra-strand cross-links, or to convert double stranded DNA to a nano-scale wire. Such applications largely depend on the presence of a modified nucleobase in both strands engaged in the duplex formation. Hybridization of metal-ion-binding oligonucleotide analogs with natural nucleic acid sequences has received much less attention in spite of obvious applications. While the natural oligonucleotides hybridize with high selectivity, their affinity for complementary sequences is inadequate for a number of applications. In the case of DNA, for example, more than 10 consecutive Watson-Crick base pairs are required for a stable duplex at room temperature, making targeting of sequences shorter than this challenging. For example, many types of cancer exhibit distinctive profiles of oncogenic miRNA, the diagnostics of which is, however, difficult owing to the presence of only short single stranded loop structures. Metallo-oligonucleotides, with their superior affinity towards their natural complements, would offer a way to overcome the low stability of short duplexes. In this study a number of metal-ion-binding surrogate nucleosides were prepared and their interaction with nucleoside 5´-monophosphates (NMPs) has been investigated by 1H NMR spectroscopy. To find metal ion complexes that could discriminate between natural nucleobases upon double helix formation, glycol nucleic acid (GNA) sequences carrying a PdII ion with vacant coordination sites at a predetermined position were synthesized and their affinity to complementary as well as mismatched counterparts quantified by UV-melting measurements.

Disclosure of HIV status and stigma in rural communities in Brazil: A conundrum for researchers

Étude de cas / Case study

Photothermal Investigations on Certain Plasma Polymerized Thin Films and Near IR Overtone Studies of Some Organic Molecules

Photothermal effect refers to heating of a sample due to the absorption of electromagnetic radiation. Photothermal (PT) heat generation which is an example of energy conversion has in general three kinds of applications. 1. PT material probing 2. PT material processing and 3. PT material destruction. The temperatures involved increases from 1-. 3. Of the above three, PT material probing is the most important in making significant contribution to the field of science and technology. Photothermal material characterization relies on high sensitivity detection techniques to monitor the effects caused by PT material heating of a sample. Photothermal method is a powerful high sensitivity non-contact tool used for non-destructive thermal characterization of materials. The high sensitivity of the photothermal methods has led to its application for analysis of low absorbance samples. Laser calorimetry, photothermal radiometry, pyroelectric technique, photoacoustic technique, photothermal beam deflection technique, etc. come under the broad class ofphotothermal techniques. However the choice of a suitable technique depends upon the nature of the sample, purpose of measurement, nature of light source used, etc. The present investigations are done on polymer thin films employing photothermal beam deflection technique, for the successful determination of their thermal diffusivity. Here the sample is excited by a He-Ne laser (A = 6328...\ ) which acts as the pump beam. Due to the refractive index gradient established in the sample surface and in the adjacent coupling medium, another optical beam called probe beam (diode laser, A= 6500A ) when passed through this region experiences a deflection and is detected using a position sensitive detector and its output is fed to a lock-in amplifier from which the amplitude and phase of the deflection can be directly obtained. The amplitude and phase of the signal is suitably analysed for determining the thermal diffusivity.The production of polymer thin film samples has gained considerable attention for the past few years. Plasma polymerization is an inexpensive tool for fabricating organic thin films. It refers to formation of polymeric materials under the influence of plasma, which is generated by some kind of electric discharge. Here plasma of the monomer vapour is generated by employing radio frequency (MHz) techniques. Plasma polymerization technique results in homogeneous, highly adhesive, thermally stable, pinhole free, dielectric, highly branched and cross-linked polymer films. The possible linkage in the formation of the polymers is suggested by comparing the FTIR spectra of the monomer and the polymer.Near IR overtone investigations on some organic molecules using local mode model are also done. Higher vibrational overtones often provide spectral simplification and greater resolution of peaks corresponding to nonequivalent X-H bonds where X is typically C, N or O. Vibrational overtone spectroscopy of molecules containing X-H oscillators is now a well established tool for molecular investigations. Conformational and steric differences between bonds and structural inequivalence ofCH bonds (methyl, aryl, acetylenic, etc.) are resolvable in the higher overtone spectra. The local mode model in which the X-H oscillators are considered to be loosely coupled anharmonic oscillators has been widely used for the interpretation of overtone spectra. If we are exciting a single local oscillator from the vibrational ground state to the vibrational state v, then the transition energy of the local mode overtone is given by .:lE a......v = A v + B v2 • A plot of .:lE / v versus v will yield A, the local mode frequency as the intercept and B, the local mode diagonal anharmonicity as the slope. Here A - B gives the mechanical frequency XI of the oscillator and B = X2 is the anharmonicity of the bond. The local mode parameters XI and X2 vary for non-equivalent X-H bonds and are sensitive to the inter and intra molecular environment of the X-H oscillator.

Systematics, Germplasm evaluation and pattern of distribution and abundance of freshwater fishes of Kerala (lndia)

The overall focus of the thesis involves the systematics,germplasm evaluation and pattern of distribution and abundance of freshwater fishes of kerala (india).Biodiversity is the measure of variety of Life.With the signing on the convention on biodiversity, the countries become privileged with absolute rights and responsibility to conserve and utilize their diverse resources for the betterment of mankind in a sustainable way. South-east Asia along with Africa and South America were considered to be the most biodiversity rich areas in the world .The tremendous potential associated with the sustainable utilization of fish germplasm resources of various river systems of Kerala for food, aquaculture and ornamental purposes have to be fully tapped for economic upliftment of fisherman community and also for equitable sharing of benefits among the mankind without compromising the conservation of the rare and unique fish germplasm resources for the future generations.The study was carried during April 2000 to December 2004. 25 major river systems of Kerala were surveyed for fish fauna for delineating the pattern of distribution and abundance of fishes both seasonally and geographically.The results of germplasm inventory and evaluation of fish species were presented both for the state and also river wise. The results of evaluation of fish species for their commercial utilization revealed that, of the 145, 76 are ornamental, 47 food and 22 cultivable. 21 species are strictly endemic to Kerala rivers. The revalidation on biodiversity status of the fishes assessed based on IUCN is so alarming that a high percentage of fishes (59spp.) belong to threatened category which is inclusive of 8 critically ndangered (CR), 36 endangered and 15 species under vulnerable (VU) category.The river wise fish germplasm inventory surveys were conducted in 25 major river systems of Kerala.The results of the present study is indicative of existence of several new fish species in the streams and rivulets located in remote areas of the forests and therefore, new exclusive surveys are required to surface fish species new to science, new distributional records etc, for the river systems.The results of fish germplasm evaluation revealed that there exist many potential endemic ornamental and cultivable fishes in Kerala. It is found imperative to utilize these species sustainably for improving the aquaculture production and aquarium trade of the country which would definitely fetch more income and generate employment.

Studies on magnetic monopole solutions of non-abelian gauge theories and related problems

In 1931 Dirac studied the motion of an electron in the field of a magnetic monopole and found that the quantization of electric charge can be explained by postulating the mere existence of a magnetic monopole. Since 1974 there has been a resurgence of interest in magnetic monopole due to the work of ‘t’ Hooft and Polyakov who independently observed that monopoles can exist as finite energy topologically stable solutions to certain spontaneously broken gauge theories. The thesis, “Studies on Magnetic Monopole Solutions of Non-abelian Gauge Theories and Related Problems”, reports a systematic investigation of classical solutions of non-abelian gauge theories with special emphasis on magnetic monopoles and dyons which possess both electric and magnetic charges. The formation of bound states of a dyon with fermions and bosons is also studied in detail. The thesis opens with an account of a new derivation of a relationship between the magnetic charge of a dyon and the topology of the gauge fields associated with it. Although this formula has been reported earlier in the literature, the present method has two distinct advantages. In the first place, it does not depend either on the mechanism of symmetry breaking or on the nature of the residual symmetry group. Secondly, the results can be generalized to finite temperature monopoles.

Impact of sward type, cutting date and conditioning temperature on mass and energy flows in the integrated generation of solid fuel and biogas from semi-natural grassland

Energy production from biomass and the conservation of ecologically valuable grassland habitats are two important issues of agriculture today. The combination of a bioenergy production, which minimises environmental impacts and competition with food production for land with a conversion of semi-natural grasslands through new utilization alternatives for the biomass, led to the development of the IFBB process. Its basic principle is the separation of biomass into a liquid fraction (press fluid, PF) for the production of electric and thermal energy after anaerobic digestion to biogas and a solid fraction (press cake, PC) for the production of thermal energy through combustion. This study was undertaken to explore mass and energy flows as well as quality aspects of energy carriers within the IFBB process and determine their dependency on biomass-related and technical parameters. Two experiments were conducted, in which biomass from semi-natural grassland was conserved as silage and subjected to a hydrothermal conditioning and a subsequent mechanical dehydration with a screw press. Methane yield of the PF and the untreated silage was determined in anaerobic digestion experiments in batch fermenters at 37°C with a fermentation time of 13-15 and 27-35 days for the PF and the silage, respectively. Concentrations of dry matter (DM), ash, crude protein (CP), crude fibre (CF), ether extract (EE), neutral detergent fibre (NDF), acid detergent fibre (ADF), acid detergent ligning (ADL) and elements (K, Mg, Ca, Cl, N, S, P, C, H, N) were determined in the untreated biomass and the PC. Higher heating value (HHV) and ash softening temperature (AST) were calculated based on elemental concentration. Chemical composition of the PF and mass flows of all plant compounds into the PF were calculated. In the first experiment, biomass from five different semi-natural grassland swards (Arrhenaterion I and II, Caricion fuscae, Filipendulion ulmariae, Polygono-Trisetion) was harvested at one late sampling (19 July or 31 August) and ensiled. Each silage was subjected to three different temperature treatments (5°C, 60°C, 80°C) during hydrothermal conditioning. Based on observed methane yields and HHV as energy output parameters as well as literature-based and observed energy input parameters, energy and green house gas (GHG) balances were calculated for IFBB and two reference conversion processes, whole-crop digestion of untreated silage (WCD) and combustion of hay (CH). In the second experiment, biomass from one single semi-natural grassland sward (Arrhenaterion) was harvested at eight consecutive dates (27/04, 02/05, 09/05, 16/05, 24/05, 31/05, 11/06, 21/06) and ensiled. Each silage was subjected to six different treatments (no hydrothermal conditioning and hydrothermal conditioning at 10°C, 30°C, 50°C, 70°C, 90°C). Energy balance was calculated for IFBB and WCD. Multiple regression models were developed to predict mass flows, concentrations of elements in the PC, concentration of organic compounds in the PF and energy conversion efficiency of the IFBB process from temperature of hydrothermal conditioning as well as NDF and DM concentration in the silage. Results showed a relative reduction of ash and all elements detrimental for combustion in the PC compared to the untreated biomass of 20-90%. Reduction was highest for K and Cl and lowest for N. HHV of PC and untreated biomass were in a comparable range (17.8-19.5 MJ kg-1 DM), but AST of PC was higher (1156-1254°C). Methane yields of PF were higher compared to those of WCD when the biomass was harvested late (end of May and later) and in a comparable range when the biomass was harvested early and ranged from 332 to 458 LN kg-1 VS. Regarding energy and GHG balances, IFBB, with a net energy yield of 11.9-14.1 MWh ha-1, a conversion efficiency of 0.43-0.51, and GHG mitigation of 3.6-4.4 t CO2eq ha-1, performed better than WCD, but worse than CH. WCD produces thermal and electric energy with low efficiency, CH produces only thermal energy with a low quality solid fuel with high efficiency, IFBB produces thermal and electric energy with a solid fuel of high quality with medium efficiency. Regression models were able to predict target parameters with high accuracy (R2=0.70-0.99). The influence of increasing temperature of hydrothermal conditioning was an increase of mass flows, a decrease of element concentrations in the PC and a differing effect on energy conversion efficiency. The influence of increasing NDF concentration of the silage was a differing effect on mass flows, a decrease of element concentrations in the PC and an increase of energy conversion efficiency. The influence of increasing DM concentration of the silage was a decrease of mass flows, an increase of element concentrations in the PC and an increase of energy conversion efficiency. Based on the models an optimised IFBB process would be obtained with a medium temperature of hydrothermal conditioning (50°C), high NDF concentrations in the silage and medium DM concentrations of the silage.

Prevalence of intestinal parasites in small ruminants and their senstivity to treatments with ethnobotanical remedies in Cholistan, Pakistan

Livestock production contributes substantially to the livelihoods of poor rural farmers in Pakistan; strengthening pastoral communities plays an imperative role in the country’s thrive for poverty alleviation. Intestinal helminths constitute a major threat for pastoral livestock keepers in the whole country because chronic infestation leads to distinct losses in livestock productivity, particularly the growth of young animals. Synthetic anthelmintics have long been considered the only effective way of controlling this problem but high prices, side effects and chemical residues/toxicity problems, or development of resistance, lead to their very limited use in many pastoral systems. Additionally, poor pastoralists in remote areas of Pakistan hardly have access to appropriate anthelmintic drugs, which are also relatively expensive due to the long routes of transportation. The search for new and more sustainable ways of supporting livestock keepers in remote areas has given rise to studies of ethno-botanicals or traditional plant-based remedies to be used in livestock health care. Plant-based remedies are cheap or free of cost, environmentally safe and generally create no problem of drug resistance; they thus might substitute allopathic drugs. Furthermore, these remedies are easily available in remote areas and simple to prepare and/or administer. Cholistan desert is a quite poor region of Pakistan and the majority of its inhabitants are practicing a nomadic life. The region’s total livestock population (1.29 million heads) is almost twice that of the human population. Livestock husbandry is the primordial occupation of the communities and traditionally wealth assessment was based on the number of animals, especially goats and sheep, owned by an individual. Fortunately, about 60% of this desert region is richly endowed with highly adapted grasses, shrubs and trees. This natural flora has a rich heritage of scientifically unexplored botanical pharmacopoeia. Against this background, the present research project that was conducted under the umbrella of the International Center for Development and Decent Work at Kassel University, focused on a development aspect: in the Cholistan desert region it was firstly examined how pastoralists manage their livestock, which major health problems they face for the different animal species, and which of the naturally occurring plants they use for the treatment of animal diseases (Chapter 2). For this purpose, a baseline survey was carried out across five locations in Cholistan, using a structured questionnaire to collect data from 100 livestock farmers (LF) and 20 local healers (LH). Most of LF and LH were illiterate (66%; 70%). On average, LH had larger herds (109 animals) than LF (85 animals) and were more experienced in livestock husbandry and management. On average LF spent about 163 Euro per year on the treatment of their livestock, with a huge variability in expenditures. Eighty-six traditional remedies based on 64 plants belonging to 43 families were used. Capparaceae was the botanical family with the largest number of species used (4), followed by Chenopodiaceae, Poaceae, Solanaceae and Zygophyllaceae (3). The plants Capparis decidua (n=55 mentions), Salsola foetida (n=52), Suaeda fruticosa (n=46), Haloxylon salicornicum (n=42) and Haloxylon recurvum (n=39) were said to be most effective against the infestations with gastrointestinal parasites. Aerial parts (43%), leaves (26%), fruits (9%), seeds and seed oils (9%) were the plant parts frequently used for preparation of remedies, while flowers, roots, bulbs and pods were less frequently used (<5%). Common preparations were decoction, jaggery and ball drench; oral drug administration was very common. There was some variation in the doses used for different animal species depending on age, size and physical condition of the animal and severity of the disease. In a second step the regionally most prevalent gastrointestinal parasites of sheep and goats were determined (Chapter 3) in 500 animals per species randomly chosen from pastoral herds across the previously studied five localities. Standard parasitological techniques were applied to identify the parasites in faecal samples manually collected at the rectum. Overall helminth prevalence was 78.1% across the 1000 animals; pure nematode infestations were most prevalent (37.5%), followed by pure trematode (7.9%), pure cestode (2.6%) and pure protozoa infestations (0.8%). Mixed infestations with nematodes and trematodes occurred in 6.4% of all animals, mixed nematode-cestode infestations in 3.8%, and all three groups were found in 19.1% of the sheep and goats. In goats more males (81.1%) than females (77.0%) were infested, the opposite was found in sheep (73.6% males, 79.5% females). Parasites were especially prevalent in suckling goats (85.2%) and sheep (88.5%) and to a lesser extent in young (goats 80.6%, sheep 79.3%) and adult animals (goats 72.8%, sheep 73.8%). Haemonchus contortus, Trichuris ovis and Paramphistomum cervi were the most prevalent helminths. In a third step the in vitro anthelmintic activity of C. decidua, S. foetida, S. fruticosa, H. salicornicum and H. recurvum (Chapter 2) was investigated against adult worms of H. contortus, T. ovis and P. cervi (Chapter 3) via adult motility assay (Chapter 4). Various concentrations ranging from 7.8 to 500 mg dry matter/ml of three types of extracts of each plant, i.e. aqueous, methanol, and aqueous-methanol (30:70), were used at different time intervals to access their anthelmintic activity. Levamisol (0.55 mg/ml) and oxyclozanide (30 mg/ml) served as positive and phosphate-buffered saline as negative control. All extracts exhibited minimum and maximum activity at 2 h and 12 h after parasite exposure; the 500 mg/ml extract concentrations were most effective. Plant species (P<0.05), extract type (P<0.01), parasite species (P<0.01), extract concentration (P<0.01), time of exposure (P<0.01) and their interactions (P<0.01) had significant effects on the number of immobile/dead helminths. From the comparison of LC50 values it appeared that the aqueous extract of C. decidua was more potent against H. contortus and T. ovis, while the aqueous extract of S. foetida was effective against P. cervi. The methanol extracts of H. recurvum were most potent against all three types of parasites, and its aqueous-methanol extract was also very effective against T. ovis and P. cervi. Based on these result it is concluded that the aqueous extract of C. decidua, as well as the methanol and aqueous-methanol extract of H. recurvum have the potential to be developed into plant-based drugs for treatment against H. contortus, T. ovis and P. cervi infestations. Further studies are now needed to investigate the in vivo anthelmintic activity of these plants and plant extracts, respectively, in order to develop effective, cheap and locally available anthelmintics for pastoralists in Cholistan and neighboring desert regions. This will allow developing tangible recommendations for plant-based anthelminthic treatment of sheep and goat herds, and by this enable pastoralists to maintain healthy and productive flocks at low costs and probably even manufacture herbal drugs for marketing on a regional scale.

Sustainability of Small Scale Farming in a Mountain Region: Case Study of the Khaling Rai Population of the Solukhumbu, Nepal

The Khaling Rai live in a remote area of the mountain region of Nepal. Subsistence farming is central to their livelihood strategy, the sustainability of which was examined in this study. The sustainable livelihood approach was identified as a suitable theoretical framework to analyse the assets of the Khaling Rai. A baseline study was conducted using indicators to assess the outcome of the livelihood strategies under the three pillars of sustainability – economic, social and environmental. Relationships between key factors were analysed. The outcome showed that farming fulfils their basic need of food security, with self-sufficiency in terms of seeds, organic fertilisers and tools. Agriculture is almost totally non-monitized: crops are grown mainly for household consumption. However, the crux faced by the Khaling Rai community is the need to develop high value cash crops in order to improve their livelihoods while at the same time maintaining food security. Institutional support in this regard was found to be lacking. At the same time there is declining soil fertility and an expanding population, which results in smaller land holdings. The capacity to absorb risk is inhibited by the small size of the resource base and access only to small local markets. A two-pronged approach is recommended. Firstly, the formation of agricultural cooperative associations in the area. Secondly, through them the selection of key personnel to be put forward for training in the adoption of improved low-cost technologies for staple crops and in the introduction of appropriate new cash crops.