383 resultados para mould


Relevância:

10.00% 10.00%

Publicador:

Resumo:

Networked Learning, e-Learning and Technology Enhanced Learning have each been defined in different ways, as people's understanding about technology in education has developed. Yet each could also be considered as a terminology competing for a contested conceptual space. Theoretically this can be a ‘fertile trans-disciplinary ground for represented disciplines to affect and potentially be re-orientated by others’ (Parchoma and Keefer, 2012), as differing perspectives on terminology and subject disciplines yield new understandings. Yet when used in government policy texts to describe connections between humans, learning and technology, terms tend to become fixed in less fertile positions linguistically. A deceptively spacious policy discourse that suggests people are free to make choices conceals an economically-based assumption that implementing new technologies, in themselves, determines learning. Yet it actually narrows choices open to people as one route is repeatedly in the foreground and humans are not visibly involved in it. An impression that the effective use of technology for endless improvement is inevitable cuts off critical social interactions and new knowledge for multiple understandings of technology in people's lives. This paper explores some findings from a corpus-based Critical Discourse Analysis of UK policy for educational technology during the last 15 years, to help to illuminate the choices made. This is important when through political economy, hierarchical or dominant neoliberal logic promotes a single ‘universal model’ of technology in education, without reference to a wider social context (Rustin, 2013). Discourse matters, because it can ‘mould identities’ (Massey, 2013) in narrow, objective economically-based terms which 'colonise discourses of democracy and student-centredness' (Greener and Perriton, 2005:67). This undermines subjective social, political, material and relational (Jones, 2012: 3) contexts for those learning when humans are omitted. Critically confronting these structures is not considered a negative activity. Whilst deterministic discourse for educational technology may leave people unconsciously restricted, I argue that, through a close analysis, it offers a deceptively spacious theoretical tool for debate about the wider social and economic context of educational technology. Methodologically it provides insights about ways technology, language and learning intersect across disciplinary borders (Giroux, 1992), as powerful, mutually constitutive elements, ever-present in networked learning situations. In sharing a replicable approach for linguistic analysis of policy discourse I hope to contribute to visions others have for a broader theoretical underpinning for educational technology, as a developing field of networked knowledge and research (Conole and Oliver, 2002; Andrews, 2011).

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Diabetic nephropathy (DN) is characterized by an early, progressive expansion and sclerosis of the glomerular mesangium leading to glomerulosclerosis. This is associated with parallel fibrosis of the renal interstitium. In experimental renal scarring, the protein cross-linking enzyme, tissue transglutaminase (tTg), is up-regulated and externalized causing an increase in its crosslink product, e-(γ-glutamyl)-lysine, in the extracellular space. This potentially contributes to the extracellular matrix (ECM) accumulation central to tissue fibrosis by increasing deposition and inhibiting breakdown. We investigated if a similar mechanism may contribute to the ECM expansion characteristic of DN using the rat streptozotocin model over 120 days. Whole kidney e-(γ-glutamyl)-lysine (HPLC analysis) was significantly increased from Day 90 (+337%) and peaked at Day 120 (+650%) (p <0.05). Immunofluorescence showed this increase to be predominantly extracellular in the peritubular interstitial space, but also in individual glomeruli. Total kidney transglutaminase (Tg) was not elevated. However, using a Tg in situ activity assay, increased Tg was detected in both the extracellular interstitial space and glomeruli by Day 60, with a maximal 53% increase at Day 120 (p <0.05). Using a specific anti-tTg antibody, immunohistochemistry showed a similar increase in extracellular enzyme in the interstitium and glomeruli. To biochemically characterize glomerular changes, glomeruli were isolated by selective sieving. In line with whole kidney measurement, there was an increase in glomerular e-(γ-glutamyl) lysine (+ 361%); however, in the glomeruli this was associated with increases in Tg activity (+228%) and tTg antigen by Western blotting (+215%). Importantly, the ratio of glomerular e-(γ-glutamyl) lysine to hydroxyproline increased by 2.2-fold. In DN, changes in the kidney result in increased translocation of tTg to the extracellular environment where high Ca2+ and low GTP levels allow its activation. In the tubulointerstitium this is independent of increased tTg production, but dependent in the glomerulus. This leads to excessive ECM cross-linking, contributing to the renal fibrosis characteristic of progressive DN.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Currently, there is a great search for materials derived from renewable sources. The vegetable fibers as reinforcement for polymer matrixes, has been used as an alternative to replace synthetic fibres, being biodegradable and of low cost. The present work aims to develop a composite material with epoxy resin reinforced with curauá fibre with the addition of alumina trihydrate (aluminum hydroxide, Al(OH)3) as a flame retardant, which was used in proportions of 10 %, 20% and 30% of the total volume of the composite. The curauá fibers have gone through a cleaning process with an alkaline bath of sodium hydroxide (NaOH ), parallelized by hand and cut carding according to the default length . They were molded composites with fibers 30cm. Composites were molded in a Lossy Mold with unidirectional fibres in the proportion of 20% of the total volume of the composite. The composites were prepared in the Chemical Processing Laboratory of the Textile Engineering Department at UFRN. To measure the performance of the material, tests for the resistance to traction and flexion were carried out. with samples that were later analyzed in the Electronic Microscopy Apparatus (SEM ). The composites showed good mechanical properties by the addition of flame retardant and in some cases, leaving the composite more vulnerable to breakage. These mechanical results were analyzed by chi-square statistical test at the 5% significance level to check for possible differences between the composite groups. Flammability testing was conducted based on the standard Underwriters Laboratory 94 and the material showed a satisfactory result taking their average burn rate (mm / min) decreasing with increasing addition of the flame retardant composite.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This report is a review of additive and subtractive manufacturing techniques. This approach (additive manufacturing) has resided largely in the prototyping realm, where the methods of producing complex freeform solid objects directly from a computer model without part-specific tooling or knowledge. But these technologies are evolving steadily and are beginning to encompass related systems of material addition, subtraction, assembly, and insertion of components made by other processes. Furthermore, these various additive processes are starting to evolve into rapid manufacturing techniques for mass-customized products, away from narrowly defined rapid prototyping. Taking this idea far enough down the line, and several years hence, a radical restructuring of manufacturing could take place. Manufacturing itself would move from a resource base to a knowledge base and from mass production of single use products to mass customized, high value, life cycle products, majority of research and development was focused on advanced development of existing technologies by improving processing performance, materials, modelling and simulation tools, and design tools to enable the transition from prototyping to manufacturing of end use parts.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The purpose of this research is to investigate potential methods to produce an ion-exchange membrane that can be integrated directly into a polydimethylsiloxane Lab-on-a-Chip or Micro-Total-Analysis-System. The majority of microfluidic membranes are based on creating microporous structures, because it allows flexibility in the choice of material such that it can match the material of the microfluidic chip. This cohesion between the material of the microfluidic chip and membrane is an important feature to prevent bonding difficulties which can lead to leaking and other practical problems. However, of the materials commonly used to manufacture microfluidic chips, there are none that provide the ion-exchange capability. The DuPont product Nafion{TM} is chosen as the ion-exchange membrane, a copolymer with high conductivity and selectivity to cations and suitable for many applications such as electrolysis of water and the chlor-alkali process. The use of such an ion-exchange membrane in microfluidics could have multiple advantages, but there is no reversible/irreversible bonding that occurs between PDMS and Nafion{TM}. In this project multiple methods of physical entrapment of the ion-exchange material inside a film of PDMS are attempted. Through the use of the inherent properties of PDMS, very inexpensive sugar granulate can be used to make an inexpensive membrane mould which does not interfere with the PDMS crosslinking process. After dissolving away this sacrificial mould material, Nafion{TM} is solidified in the irregular granulate holes. Nafion{TM} in this membrane is confined in the irregular shape of the PDMS openings. The outer structure of the membrane is all PDMS and can be attached easily and securely to any PDMS-based microfluidic device through reversible or irreversible PDMS/PDMS bonding. Through impedance measurement, the effectiveness of these integrated membranes are compared against plain Nafion{TM} films in simple sodium chloride solutions.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This paper highlights for the first time a full comprehension of the deformation procedure during the injection stretch blow moulding (ISBM) process of poly(ethylene terephthalate) (PET) containers, namely thin-walled rigid bottles. The processes required to form PET bottles are complicated and extensive; any development in understanding the nature of material deformation can potentially improve the bottle optimisation process. Removing the bottle mould and performing free-stretch-blow (FSB) experiments revealed insight into the bottle forming characteristics at various preform temperatures and blowing rates. Process outputs cavity pressure and stretch-rod force were recorded using at instrumented stretch-rod and preform surface strain mapping was determined using a combination of a unique patterning procedure and high speed stereoscopic digital image correlation. The unprecedented experimental analysis reveals that the deformation behaviour varies considerably with contrasting process input parameters. Investigation into the effect on deformation mode, strain rate and final bottle shape provide a basis for full understanding of the process optimisation and therefore how the process inputs may aid development of the preferred optimised container.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

A novel processing method for the fast and economic production of hollow ceramic components has been developed by combining in situ coagulation moulding with a modified version of the technique of rotary moulding[Binner, J. G. P., Al-Dawery, I. A., Tari, G. and Yan, Y., Rotary casting technique. UK Patent application No. 0506349.0, March 2005], the latter being adapted from the polymer industry. The process was found to require a high solids content suspension, hence development work was performed in this direction though in the end a new, commercial suspension was utilised. Of the three forming routes of gel casting, direct coagulation casting and in situ coagulation moulding, the latter was found to be the most promising for the new process of rotary moulding of ceramics. Due to the low value of clay-based ceramics, a new low cost coagulant was identified and the effect of lactone concentration and temperature on setting time determined. Following substantial optimisation work, it was found that a two-speed approach to multi-axial rotation was the most successful; medium sized cream jugs could be produced in just 7 min. With respect to mould materials, the porous resin normally used for pressure casting of sanitary ware was found to be the best option, though since this is quite expensive conventional plaster-of-paris moulds were found to be a suitable material to enable companies, particularly SMEs, to become familiar with the technology whilst avoiding high costs for trials. The processed articles could be successfully fired and glazed using gas-fired kilns with no sign of any black cores. Major advantages of the process include the ability to precisely calculate the amount of ceramic slip required, eliminating either slip wastage or the need to pour used slip back into the virgin material as currently happens with slip casting. In addition, since the precursor suspension has a very high solids content, the time and energy required to dry the green product and associated moulds has been considerably reduced. © 2008 Elsevier Ltd. All rights reserved.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This paper details the results from a large European Union rotomoulding research project on the adaptation and development of industrial microwave oven technology to the rotational moulding process. Following computer modelling, an industrial scale microwave oven was specifically designed, manufactured and attached to the drop-arm of a convention rotational moulding machine where extensive moulding trials were carried out. The design and development of the microwave oven and test mould, together with the savings in terms of energy efficiency and mould heating rate that were achieved are discussed.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Rotational moulding is a method to produce hollow plastic articles. Heating is normally carried out by placing the mould into a hot air oven where the plastic material in the mould is heated. The most common cooling media are water and forced air. Due to the inefficient nature of conventional hot air ovens most of the energy supplied by the oven does not go to heat the plastic and as a consequence the procedure has very long cycle times. Direct oil heating is an effective alternative in order to achieve better energy efficiency and cycle times. This research work has combined this technology with new innovative design of mould, applying the advantages of electroforming and rapid prototyping. Complex cavity geometries are manufactured by electroforming from a rapid prototyping mandrel. The approach involves conformal heating and cooling channels , where the oil flows into a parallel channel to the electroformed cavity (nickel or copper). Because of this the mould enables high temperature uniformity with direct heating and cooling of the electroformed shell, Uniform heating and cooling is important not only for good quality parts but also for good uniform wall thickness distribution in the rotationally moulded part. The experimental work with the manufactured prototype mould has enabled analysis of the thermal uniformity in the cavity, under different temperatures. Copyright © 2008 by ASME.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This paper presents the results from investigations into the differences in moulding with a novel anodised machined aluminium mould material and a conventional machined aluminium mould material. Significant differences in terms of cycletime were observed between the moulding carried out with the anodised moulding and the conventional aluminium mould surface material with no change in the shrinkage, part appearance or mechanical properties noted between either.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Rotational moulding is a unique manufacturing technique for the production of hollow plastic parts manufacturing. Moulds for rotational moulding are generally not standardized, such as for injection moulding, so each new mould must be completely manufactured except for a few ancillary parts like screws or clamps. The aim of this work has been to adapt and apply the advantages of rapid prototyping and electroforming technologies to try to achieve an innovative mould design for rotational moulding. The new innovative design integrates an electroformed shell, manufactured starting from a rapid prototyping mandrel, with different designed standard aluminium tools. The shell holder enables mould assembly with high precision a shell in a few minutes with the advantage of changing different geometries of the electroformed shells in the same tool. The overall mould cost is significantly decreased because it is only necessary to manufacture one or two shells each time, however the rest of the elements of the mould are standard and usable for an infinite number of shells, depending on size. The rapid prototyping of the mandrel enables a significant decrease the global cost of mould manufacturing as well. © 2008 Taylor & Francis Group.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Pour minoré et ignoré qu’il fût, le roman policier est désormais légitimé par l’institution littéraire. À parcourir les livres publiés dans la Caraïbe francophone, le genre demeure dans la marge de cette production [issue de la Caraïbe francophone (Haïti, Guadeloupe, Guyane française, Martinique)]. Quoiqu’il en soit, on notera que les années 1990 ont inauguré une véritable éclosion de publications de polars. Tout cela augure d’une acclimatation de ce genre qui ne s’accompagne pas moins de questionnements sur les spécificités éventuelles du polar caribéen francophone. Se situe-t-il dans la convention? Tente-il au contraire d’établir une distanciation avec la norme? C’est pour répondre à ces interrogations que cette thèse se propose d’explorer les enjeux de l’appropriation du polar provenant de cette aire géographique. À l’aune de la poétique des genres, de la sociocritique et de l’intermédialité, un corpus composé de quatorze romans fait l’objet d’une étude approfondie. Dans le premier chapitre, un bref récapitulatif permet de situer les œuvres à l’étude dans l’histoire littéraire du genre tout en soulignant l’adaptation du polar dans la Caraïbe de langue française. Il en ressort qu’un nombre significatif d’écrivains, attentifs à la latence du magico-religieux dans leur société, mettent en scène le surnaturel alors que le roman policier conventionnel plébiscite la méthode logico-déductive. C’est la raison pour laquelle le second chapitre s’intéresse à l’usage de l’inexplicable et son rapport avec le cartésianisme. Quant au troisième chapitre, il se penche sur un topos du genre : la violence telle qu’elle surgit dans ses dimensions commémoratives et répétitives de l’histoire tumultueuse de la Caraïbe. Notre corpus tend à relier la notion du crime, fut-il d’emprise originelle, à l’histoire post-coloniale. Dans la mesure où les personnages constituent un élément clé du genre, ils sont sondés, dans un quatrième chapitre, en regard de la critique sociale qu’ils incarnent et véhiculent. Le dernier chapitre cherche à circonscrire l’intermédialité qui structure et qualifie l’œuvre au sein du roman policier depuis sa genèse. Somme toute, ces divers axes contribuent à mieux comprendre le phénomène de transposition du polar dans cette région du monde.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

In the casting of metals, tundish flow, welding, converters, and other metal processing applications, the behaviour of the fluid surface is important. In aluminium alloys, for example, oxides formed on the surface may be drawn into the body of the melt where they act as faults in the solidified product affecting cast quality. For this reason, accurate description of wave behaviour, air entrapment, and other effects need to be modelled, in the presence of heat transfer and possibly phase change. The authors have developed a single-phase algorithm for modelling this problem. The Scalar Equation Algorithm (SEA) (see Refs. 1 and 2), enables the transport of the property discontinuity representing the free surface through a fixed grid. An extension of this method to unstructured mesh codes is presented here, together with validation. The new method employs a TVD flux limiter in conjunction with a ray-tracing algorithm, to ensure a sharp bound interface. Applications of the method are in the filling and emptying of mould cavities, with heat transfer and phase change.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Les anodes de carbone sont des éléments consommables servant d’électrode dans la réaction électrochimique d’une cuve Hall-Héroult. Ces dernières sont produites massivement via une chaine de production dont la mise en forme est une des étapes critiques puisqu’elle définit une partie de leur qualité. Le procédé de mise en forme actuel n’est pas pleinement optimisé. Des gradients de densité importants à l’intérieur des anodes diminuent leur performance dans les cuves d’électrolyse. Encore aujourd’hui, les anodes de carbone sont produites avec comme seuls critères de qualité leur densité globale et leurs propriétés mécaniques finales. La manufacture d’anodes est optimisée de façon empirique directement sur la chaine de production. Cependant, la qualité d’une anode se résume en une conductivité électrique uniforme afin de minimiser les concentrations de courant qui ont plusieurs effets néfastes sur leur performance et sur les coûts de production d’aluminium. Cette thèse est basée sur l’hypothèse que la conductivité électrique de l’anode n’est influencée que par sa densité considérant une composition chimique uniforme. L’objectif est de caractériser les paramètres d’un modèle afin de nourrir une loi constitutive qui permettra de modéliser la mise en forme des blocs anodiques. L’utilisation de la modélisation numérique permet d’analyser le comportement de la pâte lors de sa mise en forme. Ainsi, il devient possible de prédire les gradients de densité à l’intérieur des anodes et d’optimiser les paramètres de mise en forme pour en améliorer leur qualité. Le modèle sélectionné est basé sur les propriétés mécaniques et tribologiques réelles de la pâte. La thèse débute avec une étude comportementale qui a pour objectif d’améliorer la compréhension des comportements constitutifs de la pâte observés lors d’essais de pressage préliminaires. Cette étude est basée sur des essais de pressage de pâte de carbone chaude produite dans un moule rigide et sur des essais de pressage d’agrégats secs à l’intérieur du même moule instrumenté d’un piézoélectrique permettant d’enregistrer les émissions acoustiques. Cette analyse a précédé la caractérisation des propriétés de la pâte afin de mieux interpréter son comportement mécanique étant donné la nature complexe de ce matériau carboné dont les propriétés mécaniques sont évolutives en fonction de la masse volumique. Un premier montage expérimental a été spécifiquement développé afin de caractériser le module de Young et le coefficient de Poisson de la pâte. Ce même montage a également servi dans la caractérisation de la viscosité (comportement temporel) de la pâte. Il n’existe aucun essai adapté pour caractériser ces propriétés pour ce type de matériau chauffé à 150°C. Un moule à paroi déformable instrumenté de jauges de déformation a été utilisé pour réaliser les essais. Un second montage a été développé pour caractériser les coefficients de friction statique et cinétique de la pâte aussi chauffée à 150°C. Le modèle a été exploité afin de caractériser les propriétés mécaniques de la pâte par identification inverse et pour simuler la mise en forme d’anodes de laboratoire. Les propriétés mécaniques de la pâte obtenues par la caractérisation expérimentale ont été comparées à celles obtenues par la méthode d’identification inverse. Les cartographies tirées des simulations ont également été comparées aux cartographies des anodes pressées en laboratoire. La tomodensitométrie a été utilisée pour produire ces dernières cartographies de densité. Les résultats des simulations confirment qu’il y a un potentiel majeur à l’utilisation de la modélisation numérique comme outil d’optimisation du procédé de mise en forme de la pâte de carbone. La modélisation numérique permet d’évaluer l’influence de chacun des paramètres de mise en forme sans interrompre la production et/ou d’implanter des changements coûteux dans la ligne de production. Cet outil permet donc d’explorer des avenues telles la modulation des paramètres fréquentiels, la modification de la distribution initiale de la pâte dans le moule, la possibilité de mouler l’anode inversée (upside down), etc. afin d’optimiser le processus de mise en forme et d’augmenter la qualité des anodes.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Botrytis cinerea (Grey mould) is a necrotrophic fungus infecting over 230 plant species worldwide. It can cause major pre- and post-harvest diseases of many agronomic and horticultural crops. Botrytis cinerea causes annual economic losses of 10–100 billion US dollars worldwide and instability in the food supply (Jin and Wu, 2015). Grey mould losses, either at the farm gate or later in the food chain, could be reduced with improved knowledge of inoculum availability during production. In this paper, we report on the ability to monitor Botrytis spore concentration in glasshouse tomato production ahead of symptom development on plants. Using a light weight and portable air sampler (microtitre immunospore trap) it was possible to quantify inoculum availability within hours. Also, this study investigated the spatial aspect of the pathogen with an increase of B. cinerea concentration in bio-aerosols collected in the lower part of the glasshouse (0.5 m) and adjacent to the trained stems of the tomato plants. No obvious relationship was observed between B. cinerea concentration and the internal glasshouse environmental parameters of temperature and relative humidity. However the occurrence of higher outside wind speeds did increase the prevalence of B. cinerea conidia in the cropping environment of a vented glasshouse. Knowledge of inoculum availability at time periods when the environmental risk of pathogen infection is high should improve the targeted use and effectiveness of control inputs.