Numerical analysis of including phase change material in a domestic hot water cylinder

The domestic hot water cylinder incorporates encapsulated pcm placed in 57 vertical pipes. The use of PCM increases the thermal energy storage capacity of the cylinder and allows the use of low cost electricity during low peak periods. After experimental validation the numerical model developed in the project will be used to optimize the distribution of the pcm inside the water tank.

Analysis of the voltage source inverter with small DC-link capacitor

IIn electric drives, frequency converters are used to generatefor the electric motor the AC voltage with variable frequency and amplitude. When considering the annual sale of drives in values of money and units sold, the use of low-performance drives appears to be in predominant. These drives have tobe very cost effective to manufacture and use, while they are also expected to fulfill the harmonic distortion standards. One of the objectives has also been to extend the lifetime of the frequency converter. In a traditional frequency converter, a relatively large electrolytic DC-link capacitor is used. Electrolytic capacitors are large, heavy and rather expensive components. In many cases, the lifetime of the electrolytic capacitor is the main factor limiting the lifetime of the frequency converter. To overcome the problem, the electrolytic capacitor is replaced with a metallized polypropylene film capacitor (MPPF). The MPPF has improved properties when compared to the electrolytic capacitor. By replacing the electrolytic capacitor with a film capacitor the energy storage of the DC-linkwill be decreased. Thus, the instantaneous power supplied to the motor correlates with the instantaneous power taken from the network. This yields a continuousDC-link current fed by the diode rectifier bridge. As a consequence, the line current harmonics clearly decrease. Because of the decreased energy storage, the DC-link voltage fluctuates. This sets additional conditions to the controllers of the frequency converter to compensate the fluctuation from the supplied motor phase voltages. In this work three-phase and single-phase frequency converters with small DC-link capacitor are analyzed. The evaluation is obtained with simulations and laboratory measurements.

The SwissLipids knowledgebase for lipid biology.

MOTIVATION: Lipids are a large and diverse group of biological molecules with roles in membrane formation, energy storage and signaling. Cellular lipidomes may contain tens of thousands of structures, a staggering degree of complexity whose significance is not yet fully understood. High-throughput mass spectrometry-based platforms provide a means to study this complexity, but the interpretation of lipidomic data and its integration with prior knowledge of lipid biology suffers from a lack of appropriate tools to manage the data and extract knowledge from it. RESULTS: To facilitate the description and exploration of lipidomic data and its integration with prior biological knowledge, we have developed a knowledge resource for lipids and their biology-SwissLipids. SwissLipids provides curated knowledge of lipid structures and metabolism which is used to generate an in silico library of feasible lipid structures. These are arranged in a hierarchical classification that links mass spectrometry analytical outputs to all possible lipid structures, metabolic reactions and enzymes. SwissLipids provides a reference namespace for lipidomic data publication, data exploration and hypothesis generation. The current version of SwissLipids includes over 244 000 known and theoretically possible lipid structures, over 800 proteins, and curated links to published knowledge from over 620 peer-reviewed publications. We are continually updating the SwissLipids hierarchy with new lipid categories and new expert curated knowledge. AVAILABILITY: SwissLipids is freely available at http://www.swisslipids.org/. CONTACT: alan.bridge@isb-sib.ch SUPPLEMENTARY INFORMATION: Supplementary data are available at Bioinformatics online.

Pienvesivoiman elvytys, käyttöönotto ja kannattavuus

Uusiutuvan energian tuottamisen lisääminen on edellytys saavuttaaksemme EU:n asettamat tavoitteet. Tämän takia on syytä tutkia kaikki mahdollisuudet uusiutuvan energian tuottamisen lisäämiseksi jopa aivan pienimmistä laitoksista lähtien. Tämän työn tarkoituksena on tutkia pienvesivoiman taloudellisuutta ja kannattavuutta energiantuotannossa. Työssä suoritetaan myös kustannuslaskenta, jossa pohditaan käytöstä poistetun laitoksen palauttamista takaisin sähkön tuotantoon. Samalla käydään läpi teknisiä, taloudellisia ja lakisääteisiä kysymyksiä, joita pienvoiman verkkoonliittäminen aiheuttaa. Tämä työ on eräänlainen käsikirja pienvesivoimasta. Pienvesivoiman liittäminen jakeluverkkoon on sinällään suojausteknisesti yksinkertaista, mutta kaikkien eri taloudellisten ja lakiteknisten tekijöiden huomioonottaminen on puolestaan haastavaa. Laitosten käyttö ja kunnossapito eivät sinällään vaadi sähköteknistä osaamista, kunhan turvallisuusseikat otetaan visusti huomioon. Työssä havaittiin, että pienvesivoima ei pienissä laitoksissa riitä kattamaan suuria työvoimakustannuksia, joita syntyy, kun yritysten henkilökunta ottaa osaa laitoksen toimintaan. Toisaalta pienvesivoima on erinomainen tapa tuottaa sähköä yksityiselle ihmiselle, mikäli hän on itse valmis operoimaan laitosta eikä laske omalle työlleen suuria kustannuksia. Edellytyksenä on, että omalta maa‐alueelta löytyy pienikin puro suhteellisen läheltä jakeluverkkoa.

Hybridikäytön mitoitus liikkuvan työkoneen energian talteenottojärjestelmäksi

Työssä tarkastellaan sähköisiä energian talteenottomahdollisuuksia liikkuvissa työkoneissa. Työssä esitetään kolme erityyppistä liikkuvaan työkoneeseen soveltuvaa sähköisen energian talteenottojärjestelmää sekä mitoitetaan hybridikäyttö kahdelle erityyppiselle työkonesovellukselle kuormituskäyrien perusteella. Lisäksi työssä lasketaan hybridijärjestelmää käyttämällä saavutettava energiansäästö nykyiseen käyttöön verrattuna.

Dissulfeto de molibdênio, um material multifuncional e surpreendente

The aim of this work is to review the chemical and physical properties of layered molybdenum disulfide. The three polymorphic/polytypic modifications of the compound were found, the polytypes 2H (molybdenite) and 3R are semiconductors while the polymorph 1T is an electronic conductor. 2H-MoS2 has several important industrial applications as hydrotreatment catalysts, energy storage devices, solar cells, solid lubricants, among others. When intercalated, the 2H phase changes to a distorted 1T phase, producing unstable intercalation compounds that can be exfoliated in solution, producing single layers and consequently nanocomposites. The direct synthesis of the 1T phase produces stable intercalation compounds. Recently molybdenum disulfide was prepared as nanotubes and fulerene-like structures that bring new insights in the investigation of this important material.

Transporte de carga em compósitos de polianilina/V2O5

In this work, composites formed from a mixture of V2O5 and polyaniline (PANI) were investigated, for applications as cathode materials for secondary lithium batteries. Electrochemical quartz crystal microbalance (EQCM) data show that charge compensation in the [PANI]0.3V2O5 nanocomposite is achieved predominantly by Li+ migration. However, the charge compensation in the [PANI]V2O5 microcomposite occurs by Li+ and ClO4- transport. Electrochemical Impedance Spectroscopy (EIS) measurements reveal several benefits of nanohybrid formation, including the achievement of shorter ionic diffusion pathways, the higher diffusion rate of the lithium ion and also the higher electronic conductivity, which are responsible for a synergetic effect of the energy storage properties.

Estratégias de cultivo para produção dos plásticos biodegradáveis poli(3-Hidroxibutirato) e poli(3-hidroxibutirato-co-3-hidroxivalerato) por bactérias

Polyhydroxyalkanoates (PHAs) are carbon and energy storage materials that are accumulated as intracellular granules in a variety of microorganisms during unbalanced growth. PHAs have drawn attention due to their properties similar to conventional plastics and complete biodegradability. They can be used for food and cosmetics packaging, and in medicine and agriculture. However, their applicability is reduced because of their high production cost compared to conventional plastics. An overview on production strategies of poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) aiming at reducing the production costs is presented.

Aplicación de algunos modelos de series temporales al mercado de la electricidad en España

Hoy día, todo el mundo tiene un ojo puesto en el Mercado Eléctrico en nuestro país. No existe duda alguna sobre la importancia que tiene el comportamiento de la demanda eléctrica. Una de las peculiaridades de la electricidad que producimos, es que hoy por hoy, no existen aún métodos lo suficientemente efectivos para almacenarla, al menos en grandes cantidades. Por consiguiente, la cantidad demandada y la ofertada/producida deben casar de manera casi perfecta. Debido a estas razones, es bastante interesante tratar de predecir el comportamiento futuro de la demanda, estudiando una posible tendencia y/o estacionalidad. Profundizando más en los datos históricos de las demandas; es relativamente sencillo descubrir la gran influencia que la temperatura ambiente, laboralidad o la actividad económica tienen sobre la respuesta de la demanda. Una vez teniendo todo esto claro, podemos decidir cuál es el mejor método para aplicarlo en este tipo de series temporales. Para este fin, los métodos de análisis más comunes han sido presentados y explicados, poniendo de relieve sus principales características, así como sus aplicaciones. Los métodos en los que se ha centrado este proyecto son en los modelos de alisado y medias móviles. Por último, se ha buscado una relación entre la demanda eléctrica peninsular y el precio final que pagamos por la luz.

Pilhas alcalinas: um dispositivo útil para o ensino de Química

This paper presents the alkaline battery (MnO2/Zn) as a useful device in the teaching of chemistry. The preparation of the battery, the materials used in the preparation of the MnO2 electrode, the mechanism of energy storage and the parameters often used in the understanding of general batteries are discussed in detail. In addition, a schedule and a questionnaire that can be applied in an experimental class have been developed, which allow the assembly of an alkaline battery, its discharge using a galvanostatic or a load-resistance procedure, and the elaboration of a report based on the main text. This experimental class has been offered in the chemistry course of FFCLRP.

Desenvolvimento de processo de produção de conjuntos eletrodo-membrana-eletrodo para células a combustível baseadas no uso de membrana polimérica condutora de prótons (PEMFC) por impressão a tela

Proton exchange membrane fuel cell (PEMFC) requires membrane electrode assemblies (MEA) to generate electrical energy from hydrogen and oxygen. In this study a MEA production process by sieve printing and an ink composition were developed to produce catalyst layers of MEAs. The deposition of the exact catalyst content was possible on cathodes and anodes with only one print step. The optimal ink developed shown viscosity of 2.75 Pa s, density 1.27 g cm-3, total solid content of 33.76 % and tack of 92 U.T. The electrodes prepared in only one printing step showed higher performance than those prepared in several steps.

Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Phase voltage control and filtering in a converter-fed single-phase customer-end system of the LVDC distribution network

In recent years, the network vulnerability to natural hazards has been noticed. Moreover, operating on the limits of the network transmission capabilities have resulted in major outages during the past decade. One of the reasons for operating on these limits is that the network has become outdated. Therefore, new technical solutions are studied that could provide more reliable and more energy efficient power distributionand also a better profitability for the network owner. It is the development and price of power electronics that have made the DC distribution an attractive alternative again. In this doctoral thesis, one type of a low-voltage DC distribution system is investigated. Morespecifically, it is studied which current technological solutions, used at the customer-end, could provide better power quality for the customer when compared with the current system. To study the effect of a DC network on the customer-end power quality, a bipolar DC network model is derived. The model can also be used to identify the supply parameters when the V/kW ratio is approximately known. Although the model provides knowledge of the average behavior, it is shown that the instantaneous DC voltage ripple should be limited. The guidelines to choose an appropriate capacitance value for the capacitor located at the input DC terminals of the customer-end are given. Also the structure of the customer-end is considered. A comparison between the most common solutions is made based on their cost, energy efficiency, and reliability. In the comparison, special attention is paid to the passive filtering solutions since the filter is considered a crucial element when the lifetime expenses are determined. It is found out that the filter topology most commonly used today, namely the LC filter, does not provide economical advantage over the hybrid filter structure. Finally, some of the typical control system solutions are introduced and their shortcomings are presented. As a solution to the customer-end voltage regulation problem, an observer-based control scheme is proposed. It is shown how different control system structures affect the performance. The performance meeting the requirements is achieved by using only one output measurement, when operating in a rigid network. Similar performance can be achieved in a weak grid by DC voltage measurement. An additional improvement can be achieved when an adaptive gain scheduling-based control is introduced. As a conclusion, the final power quality is determined by a sum of various factors, and the thesis provides the guidelines for designing the system that improves the power quality experienced by the customer.

Akkujen ja superkondensaattorien yhteiskäyttö energiavarastoina ja niiden verkkoon liittäminen ajoneuvoissa

Ajoneuvojen tiukentuneet päästörajoitukset, sekä ajoneuvojen kokonaishyötysuhteen parantamisen tarve ohjaavat ajoneuvovalmistajia kehittämään uusia ratkaisuja. Energiavarastojen käyttö ajoneuvoissa on yleistynyt ja niiden käytöllä voidaan saada huomattava energiasäästö. Tässä kandidaatintyössä on esitelty erilaisia energiavarastoja ja niiden verkkoon liittämistä. Pääpaino työssä on akkujen ja superkondensaattorien rinnankytkennässä. Energiavarastot pyritään kytkemään mahdollisimman vähällä tehoelektroniikalla verkkoon. Esimerkkitapaukseksi on otettu litium-ioni akkujen ja superkondensaattorien rinnankytkentä vaihtojännitteeseen pelkällä invertterillä.

Aurinkopaneeleihin liitettävien vaihtosuuntaajien testaussuunnitelman laadinta ja toteutus

Aurinkoenergia on yksi monista uusiutuvan energian muodoista, joiden suosio on viimeisten vuosien aikana kasvanut fossiilisten polttoaineiden kallistumisen sekä ilmaston lämpenemisen vuoksi. Auringon säteilyn energiaa voidaan muuttaa sähköenergiaksi mm. aurinkopaneeleiden avulla. Aurinkopaneeleihin liitetään usein vaihtosuuntaaja, jolla tuotettu teho voidaan muokata sähköverkkoon tai kotitalouden sähköjärjestelmään sopivaksi. Tässä työssä on esitelty aurinkopaneelilla tuotettavan sähköenergian perusperiaatteet sekä tehoa tuottavan järjestelmän reunaehdot. Tutkimuksessa on perehdytty keskeisiin, aurinkopaneeleihin liitettäville vaihtosuuntaajille laadittuihin standardeihin, hyötysuhteen mittaamisen sekä sähkön laadun näkökulmista. Selvityksen avulla järjestelmän hyötysuhteen sekä lähtötehon laadun määrittämiseksi voidaan laatia standardien mukainen mittaussuunnitelma vaihtosuuntaajan nimellistehosta riippumatta. Standardien avulla on laadittu mittaussuunnitelma Global Inversonne, 100 kW - verkkovaihtosuuntaajayksikölle. Suunnitelman mukaisissa mittauksissa on tutkittu yksikön muunnoshyötysuhdetta sekä lähtöjännitteen- ja virran laatua. Lisäksi työssä on analysoitu mittaustulosten mittausepävarmuuksia ja niitä aiheuttavia tekijöitä.