BER-Based Call Admission In Wavelength-Routed Optical Networks

Consider a wavelength-routed optical network in which nodes, i.e., multiwave length cross-connect switches (XCSs), are connected by fiber to form an arbitrary physical topology. A new call is admitted into the network if an all-optical lightpath can be established between the call’s source and destination nodes. Wavelength converters are assumed absent in this work.

Sistema autônomo de iluminação utilizando energia solar

This work presents a self-sustainable lighting system using ultracapacitor as a storage device, replacing the conventional battery, using solar energy as the only energy supplier. A detailed study of solar panels, switched mode converters and ultracapacitors was made, in order to design a circuit capable of capturing solar energy and transfer it efficiently to a bank of ultracapacitors. Later, at nighttime, this energy is used for lighting in LED luminaires which have high luminous efficiency and high reliability index. This work presents the design of the solar panel, ultracapacitors bank, the development of the voltage converter circuit and charger working at the maximum power point of the solar panel. All subsystems were simulated and it was shown that the use of ultracapacitors is feasible to feed a LED lamp with enough brightness for a person to walk at night, for two night shifts, using a capacitive bank with twenty-four ultracapacitors. Replacing the battery by an ultracapacitor allows a faster recharge, with low maintenance costs, since ultracapacitors have a lifetime bigger than batteries; beyond reducing the environmental impact, as they don't use potentially toxic chemical compounds

Effect of pulse repetition rate and number of pulses in the analysis of polypropylene and high density polyethylene by nanosecond infrared laser induced breakdown spectroscopy

Pulse repetition rates and the number of laser pulses are among the most important parameters that do affect the analysis of solid materials by laser induced breakdown spectroscopy, and the knowledge of their effects is of fundamental importance for suggesting analytical strategies when dealing with laser ablation processes of polymers. In this contribution, the influence of these parameters in the ablated mass and in the features of craters was evaluated in polypropylene and high density polyethylene plates containing pigment-based PbCrO4. Surface characterization and craters profile were carried out by perfilometry and scanning electron microscopy. Area, volume and profile of craters were obtained using Taylor Map software. A laser induced breakdown spectroscopy system consisted of a Q-Switched Nd:YAG laser (1064 nm, 5 ns) and an Echelle spectrometer equipped with ICCD detector were used. The evaluated operating conditions consisted of 10, 25 and 50 laser pulses at 1, 5 and 10 Hz, 250 mJ/pulse (85 J cm(-2)), 2 mu s delay time and 6 mu s integration time gate. Differences in the topographical features among craters of both polymers were observed. The decrease in the repetition rate resulted in irregular craters and formation of edges, especially in polypropylene sample. The differences in the topographical features and ablated masses were attributed to the influence of the degree of crystallinity, crystalline melting temperature and glass transition temperature in the ablation process of the high density polyethylene and polypropylene. It was also observed that the intensities of chromium and lead emission signals obtained at 10 Hz were two times higher than at 5 Hz by keeping the number of laser pulses constant. (C) 2011 Elsevier B. V. All rights reserved.

Evaluation of the power production performance of the wavepiston, wave energy converter

In the early 1970 the community has started to realize that have as a main principle the industry one, with the oblivion of the people and health conditions and of the world in general, it could not be a guideline principle. The sea, as an energy source, has the characteristic of offering different types of exploitation, in this project the focus is on the wave energy. Over the last 15 years the Countries interested in the renewable energies grew. Therefore many devices have came out, first in the world of research, then in the commercial one; these converters are able to achieve an energy transformation into electrical energy. The purpose of this work is to analyze the efficiency of a new wave energy converter, called WavePiston, with the aim of determine the feasibility of its actual application in different wave conditions: from the energy sea state of the North Sea, to the more quiet of the Mediterranean Sea. The evaluation of the WavePiston is based on the experimental investigation conducted at the University of Aalborg, in Denmark; and on a numerical modelling of the device in question, to ascertain its efficiency regardless the laboratory results. The numerical model is able to predict the laboratory condition, but it is not yet a model which can be used for any installation, in fact no mooring or economical aspect are included yet. È dai primi anni del 1970 che si è iniziato a capire che il solo principio dell’industria con l’incuranza delle condizioni salutari delle persone e del mondo in generale non poteva essere un principio guida. Il mare, come fonte energetica, ha la caratteristica di offrire diverse tipologie di sfruttamento, in questo progetto è stata analizzata l’energia da onda. Negli ultimi 15 anni sono stati sempre più in aumento i Paesi interessati in questo ambito e di conseguenza, si sono affacciati, prima nel mondo della ricerca, poi in quello commerciale, sempre più dispositivi atti a realizzare questa trasformazione energetica. Di tali convertitori di energia ondosa ne esistono diverse classificazioni. Scopo di tale lavoro è analizzare l’efficienza di un nuovo convertitore di energia ondosa, chiamato WavePiston, al fine si stabilire la fattibilità di una sua reale applicazione in diverse condizioni ondose: dalle più energetiche del Mare del Nord, alle più quiete del Mar Mediterraneo. La valutazione sul WavePiston è basata sullo studio sperimentale condotto nell’Università di Aalborg, in Danimarca; e su di una modellazione numerica del dispositivo stesso, al fine di conoscerne l’efficienza a prescindere dalla possibilità di avere risultati di laboratorio. Il modello numerico è in grado di predirre le condizioni di laboratorio, ma non considera ancora elementi come gli ancoraggi o valutazione dei costi.

Entwicklung eines Verfahrens zur Ultraspurenbestimmung der Platingruppenelemente in Umwelt- und geologischen Proben mit einem ICP-QMS unter Verwendung der Isotopenverdünnungsanalyse sowie geeigneter Separationstechniken

ZusammenfassungSchwerpunkt dieser Arbeit war die Verfahrensentwicklung zur Ultraspurenbestimmung der Platingruppenelemente (PGE) in Umwelt- und geologischen Proben unter Verwendung der massenspektrometrischen Isotopenverdünnungsanalyse mit anschließender Bestimmung an einem Quadrupol ICP-MS (ICP-QMSIVA). Geeignete Separationstechniken in der Probenaufbereitung, um die PGE von der Matrix der untersuchten Proben zu trennen, stellten eine richtige und präzise Bestimmung der Ultraspuren an einem Quadrupol ICP-MS sicher.Das Verfahren konnte anhand von geologischen Referenzmaterialien aus Kanada sichergestellt werden. Gerade die Wiederholungsbestimmungen der verschiedenen Referenzmaterialien unter Verwendung des ICP-QMSIVA Verfahrens sind beispiellos und in dieser Form noch nicht in der Literatur beschrieben. Durch systematische Messungen konnten Richtigkeit und Präzision des Verfahrens bestätigt werden und die Inhomogenität des Referenzmaterials UMT-1 bezüglich Pt bewiesen werden. Das in dieser Arbeit entwickelte Verfahren zur Ultraspurenbestimmung der PGE mit ICP-QMSIVA wurde im Rahmen des Projektes 'Production and certification of a road dust reference material for platinum, palladium and rhodium (PGEs) in automative catalytic converters (PACEPAC)' der Europäischen Union zur Zertifizierung von zwei Referenzmaterialien für Umweltproben eingesetzt. Hierbei wurde bei der Zertifizierung ('intercomparison round') eine sehr gute Übereinstimmung der Ergebnisse mit dem gewichteten Mittelwert der Ergebnisse für Pd und Pt mit den übrigen teilnehmenden Laboratorien festgestellt. Die mit der hier entwickelten Methode erhaltenen Ergebnisse wurden ohne Ausnahme für alle gemessenen Elemente zur Zertifizierung herangezogen. Damit leistete die vorliegende Arbeit einen erheblichen Beitrag zum erfolgreichen Abschluß dieses Projekts. Den Erwartungen hinsichtlich Richtigkeit und Reproduzierbarkeit des entwickelten Verfahrens wurde somit voll entsprochen. Erneut konnte die große Bedeutung der Isotopenverdünnungstechnik für die Zertifizierung von Referenzmaterialien aufgezeigt werden, da mit dieser Technik bei sachgerechtem Einsatz Ergebnisse hoher Richtigkeit erzielt werden. Durch vergleichende Messungen mit der NiS-Dokimasie und NAA, die in einer Kooperation mit dem Kernchemischen Institut der Universität Mainz durchgeführt wurden, und dem hier verwendeten Verfahren, konnten übereinstimmende Daten, hinsichtlich der Abnahme der Konzentrationen von Pd und Pt in Abhängigkeit von der Entfernung zu einer Autobahn, erzielt werden. Diese Arbeit und die Forschungsergebnisse, die mit der anerkannten NAA erzielt wurden, zeigen, daß die PGE durch Katalysatoren von Automobilen überwiegend metallisch emittiert werden. Der anthropogene Eintrag der PGE in die Umwelt kann mit dem ICP-QMSIVA Verfahren weiterhin sehr gut verfolgt werden.

Sistemi di ancoraggio per convertitori di energia da onda galleggianti

Il presente lavoro presenta una analisi di sensitività sui parametri progettuali più significativi per i sistemi di ancoraggio di dispositivi di produzione di energia del mare di tipo galleggiante, comunemente conosciuti come Floating Wave Energy Converters (F-WEC). I convertitori di questo tipo sono installati offshore e possono basarsi su diversi principi di funzionamento per la produzione di energia: lo sfruttamento del moto oscillatorio dell’onda (chiamati Wave Active Bodies, gran parte di convertitori appartengono la tecnologia di questo tipo), la tracimazione delle onde (Overtopping Devices), o il principio della colonna d’acqua oscillante (Oscillating Water Columns). La scelta del luogo di installazione dei tali dispositivi implica una adeguata progettazione del sistema di ancoraggio che ha lo scopo di mantenere il dispositivo in un intorno sufficientemente piccolo del punto dove è stato originariamente collocato. Allo stesso tempo, dovrebbero considerarsi come elemento integrato del sistema da progettare al fine di aumentare l’efficienza d’estrazione della potenza d’onda. Le problematiche principali relativi ai sistemi di ancoraggio sono: la resistenza del sistema (affidabilità, fatica) e l’economicità. Le due problematiche sono legate tra di loro in quanto dall’aumento del resistenza dipende l’aumento della complessità del sistema di ancoraggio (aumentano il numero delle linee, si utilizzano diametri maggiori, aumenta il peso per unità di lunghezza per ogni linea, ecc.). E’ però chiaro che sistemi più affidabili consentirebbero di abbassare i costi di produzione e renderebbero certamente più competitiva l’energia da onda sul mercato energetico. I dispositivi individuali richiedono approcci progettuali diversi e l’economia di un sistema di ormeggio è strettamente legata al design del dispositivo stesso. Esistono, ad oggi, una serie di installazioni a scala quasi di prototipo di sistemi WEC che hanno fallito a causa del collasso per proprio sistema di ancoraggio, attirando così l’attenzione sul problema di una progettazione efficiente, affidabile e sicura.

Nonlinear constrained and saturated control of power electronics and electromechanical systems

Power electronic converters are extensively adopted for the solution of timely issues, such as power quality improvement in industrial plants, energy management in hybrid electrical systems, and control of electrical generators for renewables. Beside nonlinearity, this systems are typically characterized by hard constraints on the control inputs, and sometimes the state variables. In this respect, control laws able to handle input saturation are crucial to formally characterize the systems stability and performance properties. From a practical viewpoint, a proper saturation management allows to extend the systems transient and steady-state operating ranges, improving their reliability and availability. The main topic of this thesis concern saturated control methodologies, based on modern approaches, applied to power electronics and electromechanical systems. The pursued objective is to provide formal results under any saturation scenario, overcoming the drawbacks of the classic solution commonly applied to cope with saturation of power converters, and enhancing performance. For this purpose two main approaches are exploited and extended to deal with power electronic applications: modern anti-windup strategies, providing formal results and systematic design rules for the anti-windup compensator, devoted to handle control saturation, and “one step” saturated feedback design techniques, relying on a suitable characterization of the saturation nonlinearity and less conservative extensions of standard absolute stability theory results. The first part of the thesis is devoted to present and develop a novel general anti-windup scheme, which is then specifically applied to a class of power converters adopted for power quality enhancement in industrial plants. In the second part a polytopic differential inclusion representation of saturation nonlinearity is presented and extended to deal with a class of multiple input power converters, used to manage hybrid electrical energy sources. The third part regards adaptive observers design for robust estimation of the parameters required for high performance control of power systems.

Partial Discharge Phenomena in Converter and Traction Transformers: Identification and Reliability

After the development of power electronics converters, the number of transformers subjected to non-sinusoidal stresses (including DC) has increased in applications such as HVDC links and traction (electric train power cars). The effects of non-sinusoidal voltages on transformer insulation have been investigated by many researchers, but still now, there are some issues that must be understood. Some of those issues are tackled in this Thesis, studying PD phenomena behavior in Kraft paper, pressboard and mineral oil at different voltage conditions like AC, DC, AC+DC, notched AC and square waveforms. From the point of view of converter transformers, it was found that the combined effect of AC and DC voltages produces higher stresses in the pressboard that those that are present under pure DC voltages. The electrical conductivity of the dielectric systems in DC and AC+DC conditions has demonstrated to be a critical parameter, so, its measurement and analysis was also taken into account during all the experiments. Regarding notched voltages, the RMS reduction caused by notches (depending on firing and overlap angles) seems to increase the PDIV. However, the experimental results show that once PD activity has incepted, the notches increase PD repetition rate and magnitude, producing a higher degradation rate of paper. On the other hand, the reduction of mineral oil stocks, their relatively low flash point as well as environmental issues, are factors that are pushing towards the use of esters as transformer insulating fluids. This PhD Thesis also covers the study of two different esters with the scope to validate their use in traction transformers. Mineral oil was used as benchmark. The complete set of dielectric tests performed in the three fluids, show that esters behave better than mineral oil in practically all the investigated conditions, so, their application in traction transformers is possible and encouraged.

Arbitrary Waveform Multilevel Generator for High Voltage High Frequency Plasma Actuators

This dissertation presents the theory and the conducted activity that lead to the construction of a high voltage high frequency arbitrary waveform voltage generator. The generator has been specifically designed to supply power to a wide range of plasma actuators. The system has been completely designed, manufactured and tested at the Department of Electrical, Electronic and Information Engineering of the University of Bologna. The generator structure is based on the single phase cascaded H-bridge multilevel topology and is comprised of 24 elementary units that are series connected in order to form the typical staircase output voltage waveform of a multilevel converter. The total number of voltage levels that can be produced by the generator is 49. Each level is 600 V making the output peak-to-peak voltage equal to 28.8 kV. The large number of levels provides high resolution with respect to the output voltage having thus the possibility to generate arbitrary waveforms. Maximum frequency of operation is 20 kHz. A study of the relevant literature shows that this is the first time that a cascaded multilevel converter of such dimensions has been constructed. Isolation and control challenges had to be solved for the realization of the system. The biggest problem of the current technology in power supplies for plasma actuators is load matching. Resonant converters are the most used power supplies and are seriously affected by this problem. The manufactured generator completely solves this issue providing consistent voltage output independently of the connected load. This fact is very important when executing tests and during the comparison of the results because all measures should be comparable and not dependent from matching issues. The use of the multilevel converter for power supplying a plasma actuator is a real technological breakthrough that has provided and will continue to provide very significant experimental results.

Studio, simulazione e verifica sperimentale di tecniche di controllo per convertitori multilivello modulari

L’evoluzione dei componenti elettronici di potenza ed il conseguente sviluppo dei convertitori statici dell’energia elettrica hanno consentito di ottenere un’elevata efficienza energetica, sia nell’ambito degli azionamenti elettrici, sia nell’ambito della trasmissione e distribuzione dell’energia elettrica. L’efficienza energetica è una questione molto importante nell’attuale contesto storico, in quanto si sta facendo fronte ad una elevatissima richiesta di energia, sfruttando prevalentemente fonti di energia non rinnovabili. L’introduzione dei convertitori statici ha reso possibile un notevolissimo incremento dello sfruttamento delle fonti di energia rinnovabili: si pensi ad esempio agli inverter per impianti fotovoltaici o ai convertitori back to back per applicazioni eoliche. All’aumentare della potenza di un convertitore aumenta la sua tensione di esercizio: le limitazioni della tensione sopportabile dagli IGBT, che sono i componenti elettronici di potenza di più largo impiego nei convertitori statici, rendono necessarie modifiche strutturali per i convertitori nei casi in cui la tensione superi determinati valori. Tipicamente in media ed alta tensione si impiegano strutture multilivello. Esistono più tipi di configurazioni multilivello: nel presente lavoro è stato fatto un confronto tra le varie strutture esistenti e sono state valutate le possibilità offerte dall’architettura innovativa Modular Multilevel Converter, nota come MMC. Attualmente le strutture più diffuse sono la Diode Clamped e la Cascaded. La prima non è modulare, in quanto richiede un’apposita progettazione in relazione al numero di livelli di tensione. La seconda è modulare, ma richiede alimentazioni separate e indipendenti per ogni modulo. La struttura MMC è modulare e necessita di un’unica alimentazione per il bus DC, ma la presenza dei condensatori richiede particolare attenzione in fase di progettazione della tecnica di controllo, analogamente al caso del Diode Clamped. Un esempio di possibile utilizzo del convertitore MMC riguarda le trasmissioni HVDC, alle quali si sta dedicando un crescente interesse negli ultimi anni.

Ultra-Low Power and Non-intrusive Wireless Monitoring for Smart Buildings

Wireless Sensor Networks (WSNs) offer a new solution for distributed monitoring, processing and communication. First of all, the stringent energy constraints to which sensing nodes are typically subjected. WSNs are often battery powered and placed where it is not possible to recharge or replace batteries. Energy can be harvested from the external environment but it is a limited resource that must be used efficiently. Energy efficiency is a key requirement for a credible WSNs design. From the power source's perspective, aggressive energy management techniques remain the most effective way to prolong the lifetime of a WSN. A new adaptive algorithm will be presented, which minimizes the consumption of wireless sensor nodes in sleep mode, when the power source has to be regulated using DC-DC converters. Another important aspect addressed is the time synchronisation in WSNs. WSNs are used for real-world applications where physical time plays an important role. An innovative low-overhead synchronisation approach will be presented, based on a Temperature Compensation Algorithm (TCA). The last aspect addressed is related to self-powered WSNs with Energy Harvesting (EH) solutions. Wireless sensor nodes with EH require some form of energy storage, which enables systems to continue operating during periods of insufficient environmental energy. However, the size of the energy storage strongly restricts the use of WSNs with EH in real-world applications. A new approach will be presented, which enables computation to be sustained during intermittent power supply. The discussed approaches will be used for real-world WSN applications. The first presented scenario is related to the experience gathered during an European Project (3ENCULT Project), regarding the design and implementation of an innovative network for monitoring heritage buildings. The second scenario is related to the experience with Telecom Italia, regarding the design of smart energy meters for monitoring the usage of household's appliances.

Nano-Power Integrated Circuits for Energy Harvesting

The energy harvesting research field has grown considerably in the last decade due to increasing interests in energy autonomous sensing systems, which require smart and efficient interfaces for extracting power from energy source and power management (PM) circuits. This thesis investigates the design trade-offs for minimizing the intrinsic power of PM circuits, in order to allow operation with very weak energy sources. For validation purposes, three different integrated power converter and PM circuits for energy harvesting applications are presented. They have been designed for nano-power operations and single-source converters can operate with input power lower than 1 μW. The first IC is a buck-boost converter for piezoelectric transducers (PZ) implementing Synchronous Electrical Charge Extraction (SECE), a non-linear energy extraction technique. Moreover, Residual Charge Inversion technique is exploited for extracting energy from PZ with weak and irregular excitations (i.e. lower voltage), and the implemented PM policy, named Two-Way Energy Storage, considerably reduces the start-up time of the converter, improving the overall conversion efficiency. The second proposed IC is a general-purpose buck-boost converter for low-voltage DC energy sources, up to 2.5 V. An ultra-low-power MPPT circuit has been designed in order to track variations of source power. Furthermore, a capacitive boost circuit has been included, allowing the converter start-up from a source voltage VDC0 = 223 mV. A nano-power programmable linear regulator is also included in order to provide a stable voltage to the load. The third IC implements an heterogeneous multisource buck-boost converter. It provides up to 9 independent input channels, of which 5 are specific for PZ (with SECE) and 4 for DC energy sources with MPPT. The inductor is shared among channels and an arbiter, designed with asynchronous logic to reduce the energy consumption, avoids simultaneous access to the buck-boost core, with a dynamic schedule based on source priority.

Enhancement of inductive power transfer with flat spiral resonators

The aim of this thesis is to develop a depth analysis of the inductive power transfer (or wireless power transfer, WPT) along a metamaterial composed of cells arranged in a planar configuration, in order to deliver power to a receiver sliding on them. In this way, the problem of the efficiency strongly affected by the weak coupling between emitter and receiver can be obviated, and the distance of transmission can significantly be increased. This study is made using a circuital approach and the magnetoinductive wave (MIW) theory, in order to simply explain the behavior of the transmission coefficient and efficiency from the circuital and experimental point of view. Moreover, flat spiral resonators are used as metamaterial cells, particularly indicated in literature for WPT metamaterials operating at MHz frequencies (5-30 MHz). Finally, this thesis presents a complete electrical characterization of multilayer and multiturn flat spiral resonators and, in particular, it proposes a new approach for the resistance calculation through finite element simulations, in order to consider all the high frequency parasitic effects. Multilayer and multiturn flat spiral resonators are studied in order to decrease the operating frequency down to kHz, maintaining small external dimensions and allowing the metamaterials to be supplied by electronic power converters (resonant inverters).

Analysis and design of high performance multiphase electric drives for vehicle and aircraft applications

The first part of this thesis has focused on the construction of a twelve-phase asynchronous machine for More Electric Aircraft (MEA) applications. In fact, the aerospace world has found in electrification the way to improve the efficiency, reliability and maintainability of an aircraft. This idea leads to the aircraft a new management and distribution of electrical services. In this way is possible to remove or to reduce the hydraulic, mechanical and pneumatic systems inside the aircraft. The second part of this dissertation is dedicated on the enhancement of the control range of matrix converters (MCs) operating with non-unity input power factor and, at the same time, on the reduction of the switching power losses. The analysis leads to the determination in closed form of a modulation strategy that features a control range, in terms of output voltage and input power factor, that is greater than that of the traditional strategies under the same operating conditions, and a reduction in the switching power losses.

Biogas and bio-hydrogen: production and uses. A review

The first part of this essay aims at investigating the already available and promising technologies for the biogas and bio-hydrogen production from anaerobic digestion of different organic substrates. One strives to show all the peculiarities of this complicate process, such as continuity, number of stages, moisture, biomass preservation and rate of feeding. The main outcome of this part is the awareness of the huge amount of reactor configurations, each of which suitable for a few types of substrate and circumstance. Among the most remarkable results, one may consider first of all the wet continuous stirred tank reactors (CSTR), right to face the high waste production rate in urbanised and industrialised areas. Then, there is the up-flow anaerobic sludge blanket reactor (UASB), aimed at the biomass preservation in case of highly heterogeneous feedstock, which can also be treated in a wise co-digestion scheme. On the other hand, smaller and scattered rural realities can be served by either wet low-rate digesters for homogeneous agricultural by-products (e.g. fixed-dome) or the cheap dry batch reactors for lignocellulose waste and energy crops (e.g. hybrid batch-UASB). The biological and technical aspects raised during the first chapters are later supported with bibliographic research on the important and multifarious large-scale applications the products of the anaerobic digestion may have. After the upgrading techniques, particular care was devoted to their importance as biofuels, highlighting a further and more flexible solution consisting in the reforming to syngas. Then, one shows the electricity generation and the associated heat conversion, stressing on the high potential of fuel cells (FC) as electricity converters. Last but not least, both the use as vehicle fuel and the injection into the gas pipes are considered as promising applications. The consideration of the still important issues of the bio-hydrogen management (e.g. storage and delivery) may lead to the conclusion that it would be far more challenging to implement than bio-methane, which can potentially “inherit” the assets of the similar fossil natural gas. Thanks to the gathered knowledge, one devotes a chapter to the energetic and financial study of a hybrid power system supplied by biogas and made of different pieces of equipment (natural gas thermocatalitic unit, molten carbonate fuel cell and combined-cycle gas turbine structure). A parallel analysis on a bio-methane-fed CCGT system is carried out in order to compare the two solutions. Both studies show that the apparent inconvenience of the hybrid system actually emphasises the importance of extending the computations to a broader reality, i.e. the upstream processes for the biofuel production and the environmental/social drawbacks due to fossil-derived emissions. Thanks to this “boundary widening”, one can realise the hidden benefits of the hybrid over the CCGT system.