Phytochrome and light influence on germination and vigor of ocimum gratissimum L. (Lamiaceae) seeds under high irradiance conditions

Ocimum gratissimum seed germination (% germination and vigor) has been found as phytochrome dependent, having a typical High Irradiant Response (HIR). Seven treatments were tested: daylight (DL), red (R), far-red (FR), blue (B), green (G), dark (DK), and reversible (RVB). No statistical difference among the DL, R, FR, B, and G were found. DK and RVB were statistically equal and presented the lowest results. The germination also occurred in the DK treatment but in non-useful rates, and it was nonreversible in the RVB treatment. It allows these seeds to be classified as positively photoblastic. The minimum energy need to initiate the germination was evaluated by a fluency-response curve. It plotted four different exposition times to R light (1 second, 60 seconds, 1 hour, and 13 hours) against percent germination. Useful germination occurred only after 1 hour, confirming the high energy needed to incite the process. The germination rate increased with the raise of the photoequilibrium (j). The high positive correlation index found confirms the phytochrome influence in this process. Facing all the results presented here, it is suggested to sow these seeds under direct and highly intense sunlight. It is preferable to avoid places exposed to variations in the shading, because inhibition induced by dense shade effects (low R/FR ration and consequently low j established) were demonstrated irreversible, and it can lead to undesirable loss of the germination power.

Blue-greenish acrochaetioid algae in freshwater habitats are Chantransia stages of Batrachospermales sensu lato (Rhodophyta)

Fourteen culture isolates of freshwater acrochaetioid algae from distinct regions around the world were analysed, including the reddish species Audouinella hermannii, the dubious blue-greenish species A. pygmaea, and Chantransia stages from distinct taxonomic origins in the Batrachospermales sensu lato (Batrachospermaceae, Lemaneaceae and Thoreaceae). Four isolates (two 'Chantransia' stages and two species of Audouinella, A. hermannii and A. pygmaea) were tested under experimental conditions of temperature (10-25°C), irradiance (65 and 300 μmol photons m-2 s-1) and photoperiod (16:8 h and 8:16 h light/dark cycles). Plant colour is proposed as the only vegetative character that can be unequivocally applied to distinguish Audouinella from 'Chantransia', blue-greenish representing Chantransia stages and reddish applying to true Audouinella species (also forming reproductive structures other than monosporangia, e.g. tetrasporangia). Some isolates of A. pygmaea were proven to be unequivocally 'Chantransia stages owing either to production of juvenile gametophytes or to derivation from carpospores. No association of the morphology of A. pygmaea was found with any particular species, thus it should be regarded as a complex involving many species of the Batrachospermales sensu lato, as is also the case with A. macrospora. We therefore recommend that all blue-greenish acrochaetioid algae in freshwater habitats be considered as Chantransia stages of members of the Batrachospermales, and that the informal descriptors pygmaea and macrospora be used to distinguish the two discernable morphologies. Induction of gametophytes occurred under much wider conditions than previously reported, reinforcing the conclusion that requirements are probably species-specific. Although phenotypic plasticity was in evidence, with temperature, irradiance and photoperiod affecting morphology, no alga showed variation outside the limits based on traditional taxonomic studies. No overall trend was observed for vegetative or reproductive characters in response to temperature, irradiance and photoperiod for all the algae tested, only for specific algae or characters. Effects of temperature and irradiance on morphological characters were more evident, as well as strong interactions between these variables, whereas few differences were generally found in response to photoperiod and irradiance.

Temperature analysis during bonding of brackets using LED or halogen light base units

The purpose of our investigation is to compare the intrapulpal temperature changes following blue LED system and halogen lamp irradiation at the enamel surface of permanent teeth. The fixation of brackets using composite resin is more comfortable and faster when using a photo-curable composite. Several light sources can be used: halogens, arc plasma, lasers, and recently blue LED systems. An important aspect to be observed during such a procedures is the temperature change. In this study, we have used nine human extracted permanent teeth: three central incisors, three lateral incisors, and three canines. Teeth were exposed to two light sources: blue LED system (preliminary commercial model LEC 470-II) and halogen lamp (conventional photo-cure equipment). The surface of teeth was exposed for 20, 40, and 60 sec at the buccal and lingual enamel surface with an angle of 45 degrees. Temperature values measured by a thermistor placed at pulpar chamber were read in time intervals of 1 sec. We obtained plots showing the temperature evolution as a function of time for each experiment. There is a correlation between heating quantity and exposition time of light source: with increasing exposition time, heating increases into the pulpal chamber. The halogen lamp showed higher heating than the LED system, which showed a shorter time of cooling than halogen lamp. The blue LED system seems like the indicated light source for photo-cure of composite resin during the bonding of brackets. The fixation of brackets using composite resin is more comfortable and faster when using a photo-curable composite. Blue LED equipment did not heat during its use. This could permit a shorter clinical time of operation and better performance. © Mary Ann Liebert, Inc.

Polymer light emitting devices with Langmuir Blodgett (LB) films of a polyfluorene derivative

Polyfluorenes are promising materials for the emitting layer of polymer light emitting devices (PLEDs) with blue emission. In this work, we report on PLEDs fabricated with Langmuir-Blodgett (LB) films of a polyfluorene derivative, namely poly(9,9-di-hexylfluorenediyl vinylene-alt-1,4-phenylenevinylene) (PDHF-PV). Y-type LB films were transferred onto ITO substrates at a surface pressure of 35 mN m-1 and with dipping speed of 3 mm min -1. A thin aluminum layer was evaporated on top of the LB film, thus yielding a sandwich structure (ITO/PDHF-PV(LB)/Al). Current-voltage (I vs V) measurements indicate that the device displays a classical behavior of a rectifying diode. The threshold value is approximately 5 V, and the onset for visible light emission occurs at ca. 10 V. From the a.c. electrical responses we infer that the active layer has a typical behavior of PLEDs where the real component of ac conductivity obeys a power-law with the frequency. Cole-Cole plots (Im(Z) vs. Re(Z)) for the device exhibit a series of semicircles, the diameter of which decreases with increasing forward bias. This PLED structure is modeled by a parallel resistance and capacitance combination, representing the dominant mechanisms of charge transport and polarization in the organic layer, in series with a resistance representing the ITO contact. Overall, the results presented here demonstrate the feasibility of LEDs made with LB films of PDHF-PV.

Colorimetric determination of ambient ozone using indigo blue droplet

A simple and sensitive method based on a liquid droplet is described for the measurement of atmospheric ozone. A 30 μL drop of indigo blue solution is suspended in a flowing-air sampling stream. The ozone collected reacts with the indigo solution resulting in its decolorization. The colorimetric sensor is composed of two optical fibers and the source of monochromatic light was a red LED (625 nm). The calibration curve was constructed with ozone standard concentrations ranging from 37 - 123 ppbv. The detection limit achieved was 7.3 ppbv. The method considered here showed itself to be easy to apply with a fast response and a total analysis time of only 5 minutes.

Influence of pre-heat treatment and different light-curing units on Vickers hardness of a microhybrid composite resin

The aim of this study was to evaluate the hardness of a dental composite resin submitted to temperature changes before photo-activation with two light-curing unite (LCUs). Five samples (4 mm in diameter and 2 mm in thickness) for each group were made with pre-cure temperatures of 37, 54, and 60°C. The samples were photo-activated with a conventional quartz-tungsten-halogen (QTH) and blue LED LCUs during 40 s. The hardness Vickers test (VHN) was performed on the top and bottom surfaces of the samples. According to the interaction between light-curing unit and different pre-heating temperatures of composite resin, only the light-curing unit provided influences on the mean values of initial Vickers hardness. The light-curing unit based on blue LED showed hardness mean values more homogeneous between the top and bottom surfaces. The hardness mean values were not statistically significant difference for the pre-cure temperature used. According to these results, the pre-heating of the composite resin provide no influence on Vickers hardness mean values, however the blue LED showed a cure more homogeneous than QTH LCU. © 2009 Pleiades Publishing, Ltd.

Effect of light-curing units on push-out fiber post bond strength in root canal dentin

The purpose of this study was to evaluate the effectiveness of different light-curing units on the bond strength (push-out) of glass fiber posts in the different thirds of the root (cervical, middle and apical) with different adhesive luting resin systems (dual-cure total-etch; dual-cured and self-etch bonding system; and dual-cure self-adhesive cements), Disks of the samples (n = 144) were used, with approximately 1 mm of thickness of 48 bovine roots restored with glass fiber posts, that were luted with resin cements photo-activated by halogen LCU (QTH, Optilux 501) and blue LED (Ultraled), with power densities of 600 and 550 mW/cm 2, respectively. A universal testing machine (MTS 810 Material Test System) was used with a 1 mm diameter steel rod at cross-head speed of 0.5 mm/min until post extrusion, with load cell of 50 kg, for evaluation of the push-out strength in the different thirds of each sample. The push-out strength values in kgf were converted to MPa and analyzed through Analysis of Variance and Tukey's test, at significance level of 5%. The results showed that there were no statistical differences between the QTH and LED LCUs. The self-adhesive resin cement had lower values of retention. The total-etch and self-adhesive system resin cements seem to be a possible alternative for glass fiber posts cementation into the radicular canal and the LED LCU can be applied as an alternative to halogen light on photo-activation of dual-cured resin cements. © 2009 Pleiades Publishing, Ltd.

Growth of euterpe oleracea seedlings under different color nets and light conditions

Euterpe oleracea, a native palm to the Amazon, has recognized trading importance because of its fruits and heart of palm. However, it still requires general information on its propagation and cultivation. As light is essential for plant growth, this work aimed to study the effect of different color nets and light conditions on the initial growth of E. oleracea, with the objective to obtain high quality seedlings. The experiment was conducted in Jaboticabal County, São Paulo State, Brazil. The experimental design was entirely randomized, with six treatments (six light conditions: red net with 50% of shading - red Chromatinet®; blue net with 50% of shading - blue Chromatinet®; black nets with 70, 50 or 30% of shading; and full sun) and six replications (six evaluation periods: 30, 60, 90, 120, 150 and 180 days after the beginning of the experiment). Each plot consisted of four pots with one plant per pot, resulting in 144 plants. Seedling growth was monthly evaluated by collecting four plants per replication until the end of the experiment. Shoot length, root length, stem diameter, leaf number, leaf area and root and shoot dry matter were evaluated. The best quality seedlings of E. oleracea were obtained when they were cultivated under the black net with 50% of shading.

Photoelectrochemical properties of FTO/m-BiVO4 electrode in different electrolytes solutions under visible light irradiation

Photoelectrochemical properties of FTO/BiVO4 electrode were investigated in different electrolytic solutions, potassium chloride (KCl) and sodium sulphate (Na2SO4), and under visible light irradiation condition. In order to accomplish that, an FTO/BiVO4 electrode was built by combining the solution combustion synthesis technique with the dip-coating deposition process. The morphology and structure of the BiVO4 electrode were investigated through X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy. Photoelectrochemical properties were analyzed through chronoamperometry measurements. Results have shown that the FTO/BiVO4 electrode presents higher electroactivity in the electrolyte Na2SO4, leading to better current stabilization, response time, and photoinduced current density, when compared to KCl electrolyte. Besides, this electrode shows excellent performance for methylene blue degradation under visible light irradiation condition. In Na2SO4, the electrode has shown higher degradation rate, 51 %, in contrast to 44 % in KCl, plus higher rate constant, 174 × 10-4 min-1 compared to 150 × 10-4 min-1 in KCl. Results presented in this communication leads to the indication of BiVO4 thin films as alternate materials to use in heterogeneous photoelectrocatalysis, more specifically in decontamination of surface water. © 2013 Springer-Verlag Berlin Heidelberg.

Streptococcus Mutans Photoinactivation by Combination of Short Exposure of a Broad-Spectrum Visible Light and Low Concentrations of Photosensitizers

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Light emitting diode (LED) use in artificial lighting for broiler chicken production

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Very Intense Distinct Blue and Red Photoluminescence Emission in MgTiO 3 Thin Films Prepared by the Polymeric Precursor Method: An Experimental and Theoretical Approach

MgTiO3 (MTO) thin films were prepared by the polymeric precursor method with posterior spin-coating deposition. The films were deposited on Pt(111)/Ti/SiO2/Si(100) substrates and heat treated at 350 °C for 2 h and then heat treated at 400, 450, 500, 550, 600, 650 and 700 °C for 2 h. The degree of structural order−disorder, optical properties, and morphology of the MTO thin films were investigated by X-ray diffraction (XRD), micro-Raman spectroscopy (MR), ultraviolet− visible (UV−vis) absorption spectroscopy, photoluminescence (PL) measurements, and field-emission gun scanning electron microscopy (FEG-SEM) to investigate the morphology. XRD revealed that an increase in the annealing temperature resulted in a structural organization of MTO thin films. First-principles quantum mechanical calculations based on density functional theory (B3LYP level) were employed to study the electronic structure of ordered and disordered asymmetric models. The electronic properties were analyzed, and the relevance of the present theoretical and experimental results was discussed in the light of PL behavior. The presence of localized electronic levels and a charge gradient in the band gap due to a break in the symmetry are responsible for the PL in disordered MTO lattice.

White Light and Multicolor Emission Tuning in Triply Doped Yb3+/Tm3+/Er3+ Novel Fluoro-phosphate Transparent Glass-ceramics

New Yb3+, Er3+ and Tm3+ doped fluoro-phosphate glasses belonging to the system NaPO3–YF3–BaF2–CaF2 and containing up to 10 wt% of rare-earth ion fluorides were prepared and characterized by differential scanning calorimetry, absorption spectroscopy and up-conversion emission spectroscopy under excitation with a 975 nm laser diode. Transparent and homogeneous glass-ceramics have been reproducibly obtained with a view to manage the red, green and blue emission bands and generate white light. X-ray diffraction as well as electron microscopy techniques have confirmed the formation of fluorite-type cubic nanocrystals at the beginning of the crystallization process while complex nanocrystalline phases are formed after a longer heat-treatment. The prepared glass-ceramics exhibit high optical transparency even after 170 h of thermal treatment. An improvement of up-conversion emission intensity – from 10 to 160 times larger – was measured in the glass-ceramics when compared to the parent glass, suggesting an important incorporation of the rare-earth ions into the crystalline phase(s). The involved mechanisms and lifetime were described in detail as a function of heat-treatment time. Finally, a large range of designable color rendering (from orange to turquoise through white) can be observed in these materials by controlling the laser excitation power and the crystallization rate.

Photodynamic antimicrobial chemotherapy on streptococcus mutans using curcumin and toluidine blue activated by a novel LED device

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Photoelectrochemical properties of FTO/p-NiO electrode induced by UV light irradiation

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)