Eliminating non-renewable CO2 emissions from sewage treatment: An anaerobic migrating bed reactor pilot plant study

The aim of this work was to demonstrate at pilot scale a high level of energy recovery from sewage utilising a primary Anaerobic Migrating Bed Reactor (AMBR) operating at ambient temperature to convert COD to methane. The focus is the reduction in non-renewable CO2 emissions resulting from reduced energy requirements for sewage treatment. A pilot AMBR was operated on screened sewage over the period June 2003 to September 2004. The study was divided into two experimental phases. In Phase 1 the process operated at a feed rate of 10 L/h (HRT 50 h), SRT 63 days, average temperature 28 degrees C and mixing time fraction 0.05. In Phase 2 the operating parameters were 20 L/h, 26 days, 16 degrees C and 0.025. Methane production was 66% of total sewage COD in Phase 1 and 23% in Phase 2. Gas mixing of the reactor provided micro-aeration which suppressed sulphide production. Intermittent gas mixing at a useful power input of 6 W/m(3) provided satisfactory process performance in both phases. Energy consumption for mixing was about 1.5% of the energy conversion to methane in both operating phases. Comparative analysis with previously published data confirmed that methane supersaturation resulted in significant losses of methane in the effluent of anaerobic treatment systems. No cases have been reported where methane was considered to be supersaturated in the effluent. We have shown that methane supersaturation is likely to be significant and that methane losses in the effluent are likely to have been greater than previously predicted. Dissolved methane concentrations were measured at up to 2.2 times the saturation concentration relative to the mixing gas composition. However, this study has also demonstrated that despite methane supersaturation occurring, microaeration can result in significantly lower losses of methane in the effluent (< 11% in this study), and has demonstrated that anaerobic sewage treatment can genuinely provide energy recovery. The goal of demonstrating a high level of energy recovery in an ambient anaerobic bioreactor was achieved. An AMBR operating at ambient temperature can achieve up to 70% conversion of sewage COD to methane, depending on SRT and temperature. (c) 2006 Wiley Periodicals, Inc.

Studies in three phase gas-liquid-solid fluidised systems

The work is a logical continuation of research started at Aston some years ago when studies were conducted on fermentations in bubble columns. The present work highlights typical design and operating problems that could arise in such systems as waste water, chemical, biochemical and petroleum operations involving three-phase, gas-liquid-solid fluidisation; such systems are in increasing use. It is believed that this is one of few studies concerned with `true' three-phase, gas-liquid-solid fluidised systems, and that this work will contribute significantly to closing some of the gaps in knowledge in this area. The research work was mainly experimentally based and involved studies of the hydrodynamic parameters, phase holdups (gas and solid), particle mixing and segregation, and phase flow dynamics (flow regime and circulation patterns). The studies have focused particularly on the solid behaviour and the influence of properties of solids present on the above parameters in three-phase, gas-liquid-solid fluidised systems containing single particle components and those containing binary and ternary mixtures of particles. All particles were near spherical in shape and two particle sizes and total concentration levels were used. Experiments were carried out in two- and three-dimensional bubble columns. Quantitative results are presented in graphical form and are supported by qualitative results from visual studies which are also shown as schematic diagrams and in photographic form. Gas and solid holdup results are compared for air-water containing single, binary and ternary component particle mixtures. It should be noted that the criteria for selection of the materials used are very important if true three-phase fluidisation is to be achieved: this is very evident when comparing the results with those in the literature. The fluid flow and circulation patterns observed were assessed for validation of the generally accepted patterns, and the author believes that the present work provides more accurate insight into the modelling of liquid circulation in bubble columns. The characteristic bubbly flow at low gas velocity in a two-phase system is suppressed in the three-phase system. The degree of mixing within the system is found to be dependent on flow regime, liquid circulation and the ratio of solid phase physical properties. Evidence of strong `trade-off' of properties is shown; the overall solid holdup is believed to be a major parameter influencing the gas holdup structure.

Trained Neural Network Characterizing Variables for Predicting Organic Retention by Nanofiltration Membranes

Many organic compounds cause an irreversible damage to human health and the ecosystem and are present in water resources. Among these hazard substances, phenolic compounds play an important role on the actual contamination. Utilization of membrane technology is increasing exponentially in drinking water production and waste water treatment. The removal of organic compounds by nanofiltration membranes is characterized not only by molecular sieving effects but also by membrane-solute interactions. Influence of the sieving parameters (molecular weight and molecular diameter) and the physicochemical interactions (dissociation constant and molecular hydrophobicity) on the membrane rejection of the organic solutes were studied. The molecular hydrophobicity is expressed as logarithm of octanol-water partition coefficient. This paper proposes a method used that can be used for symbolic knowledge extraction from a trained neural network, once they have been trained with the desired performance and is based on detect the more important variables in problems where exist multicolineality among the input variables.

Composition of zooplankton assemblages along the Zagyva River

The species composition, longitudinal distribution and seasonal dynamics of zooplankton were studied in the Zagyva River, Hungary. A total of 108 taxa was recorded from which 61 were new for the river. Rotatoria was the most abundant group, microcrustaceans were less important, only nauplii and copepodites were represented in similar individual numbers. Frequent species included Anuraeopsis fissa, Pompholyx spp., Keratella cochlearis, Brachionus angularis, Bdelloida sp., Bosmina longirostris. Dominance of cosmopolitan species was observed both in the river and its reservoir, and species characteristic of eutrophic waters were of major importance in the latter. There was a downstream decrease in zooplankton densities, which was explained by modified conditions. The relatively large number of individuals in autumn months, and the characteristic large number of individuals in the upper section contrasted general findings of potamoplankton dynamics. On the basis of the species abundance matrix, three river sections can be distinguished (upper, middle, lower section). Due to waste water discharges - received from the Tarján Stream - we found extremely high number of individuals and the lowest diversity at the sampling site Nagybátony (148 rkm).

Eco-innovation – does additional engagement lead to additional rewards?

Purpose: Eco-innovation is any form of product, process or organisational innovation that contributes towards sustainable development. Firms can eco-innovate in a variety of ways. The purpose of this paper is to identify nine different eco-innovation activities – including such items as reducing material use per unit of output, reducing energy use per unit of output, reducing carbon dioxide (CO2) “footprint” – and the authors ask whether these act as substitutes or complements to one another. Design/methodology/approach: Eco-innovation is any form of product, process or organisational innovation that contributes towards sustainable development. Firms can eco-innovate in a variety of ways. In this paper the authors identify nine different eco-innovation activities – including such items as reducing material use per unit of output, reducing energy use per unit of output, reducing CO2 “footprint” – and the authors ask whether these act as substitutes or complements to one another. Findings: Introducing only one eco-innovation activity has little payoff (in terms of turnover per worker) with only those firms who reduce their CO2 “footprint” having higher levels of turnover per worker. When introducing more than one eco-innovation activity the authors find that certain eco-innovation activities complement one another (e.g. reducing material use within the firm at the same time as improving the ability to recycle the product after use) others act as substitutes (e.g. reducing material use within the firm at the same time as recycling waste, water or materials within the firm). Practical implications: The results suggest that firms can maximise their productive capacity by considering specific combinations of eco-innovation. This suggests that firms should plan to introduce eco-innovation which act as complements, thereby, boosting productivity. It also suggests that eco-innovation stimuli, introduced by policy makers, should be targeted at complementary eco-innovations. Originality/value: The paper analyses whether eco-innovations act as complements or substitutes. While a number of studies have analysed the importance of eco-innovation for firm performance, few have assessed the extent to which diverse types of eco-innovation interact with each other to complement or substitute for one another.

Ottimizzazione della reazione di Fenton mediante l’utilizzo di un sistema automatico di reazione

The research presented in this dissertation is aimed to the automation of the Fenton process. The Fenton reaction is finalized to the waste water pre-treatment in order to promote the abatement of the organic contaminants and make it more degradable. Reagents adopted are constituted by a mixture of iron ions and hydrogen peroxide and their effect is strictly influenced by several variables, such as: the reagents molar ratio and their quantities counterpoised to the substrate, temperature, pH, agitation, etc. Therefore, the optimization is far from being considered an easy procedure. The research was carried out using a batch configuration, through which the optimal [Fe2+]/[H2O2] and [substrate]/[H2O2] ratios were identified. Then, in order to improve the process, a semibatch configuration was performed. The preliminary results show that is possible to obtain a greater abatement efficiency for high organic burden using the semibatch configuration here proposed.

Sex steroid feedback regulation of pituitary gonadotropins during early secondary oocyte growth in coho salmon (Oncorhynchus kisutch) – a potential target of endocrine disruption.

Thesis (Ph.D.)--University of Washington, 2016-06

Evaluación de vetiver (Chrysopogon zizanioides) y la elefanta (Pennisetum purpureum) en el diseño de humedales artificiales

En este trabajo se presenta la descripción e investigación en la evaluación de vetiver (Chrysopogon zizanioides) y la elefanta (Pennisetum purpureum) en el diseño de humedales artificiales. Para el tratamiento de aguas residuales de origen doméstico, siendo la vegetación uno de los principales componentes de estos sistemas de tratamientos no convencionales. Muchos \sistemas naturales" están siendo considerados con el propósito del tratamiento del agua residual y control de la contaminación del agua, debido a su alta fiabilidad ambiental y los bajos costos de construcción y mantenimiento, es el caso de los humedales artificiales. El interés en los sistemas naturales está basado en la conservación de los recursos asociados con estos sistemas como opuesto al proceso de tratamiento convencional de aguas residuales que es intensivo respecto al uso de energía y químicos. Los wetlands o humedales artificiales constituyen una alternativa de tratamiento debido a su alta eficiencia de remoción de contaminantes, a su bajo costo de instalación y mantenimiento y a su alta fiabilidad ambiental, generalmente un humedal artificial esta constituido por un medio de soporte el cual generalmente es arena o grava, vegetación y microorganismos o biopelícula los cuales llevan los diferentes procesos bioquímicos para remover los contaminantes del afluente. El objetivo general de este trabajo ha sido: Evaluar la eficiencia de remoción de materia orgánica, sólidos, nitrógeno y fósforo total de dos especies de plantas: vetiver (Chrysopogon zizanioides) y la elefanta (Pennisetum purpureum), en el diseño de humedales artificiales para el tratamiento de aguas residuales de origen doméstico. Los humedales artificiales o sistemas pilotos, se encuentran ubicados en la universidad de Medellín y reciben una preparación de agua sintética, que asemeja a las características de un agua residual de origen doméstico. En el presente trabajo se evalúa el porcentaje de remoción de la carga orgánica de aguas residuales, en un sistema de tratamiento por humedales artificiales con dos especies vegetales. El sistema fue diseñado con tres módulos instalados de manera adjunta. En el primero no se integra ninguna especie vegetal, solo el medio de sustrato el cual constituye el blanco (-), en el segundo se integraron organismos de la especie vetiver (Chrysopogon zizanioides), en el tercer sistema piloto, organismos de la especie elefanta (Pennisetum purpureum) y en el cuarto organismos de la especie papiro japones (Cyperus alternifolius), los cuales constituyen el control positivo (+). Los módulos experimentales fueron limpiados, cortados y adecuados acorde al montaje inicial de las plantas y al espacio requerido para su disposición. A cada sistema piloto se le agrega medio de soporte constituido por grava (5 a 10 cm) y arena (15 a 20 cm), el sustrato es evaluado y caracterizado por su diámetro nominal, posterior en cada sistema se siembran las especies en un área de 3x3 y cada humedal por dos semanas se adecua bajo la solución de Hoagland y Arnon y régimen de humedad. En el agua sintética se analizaron los siguientes parámetros: pH, sólidos totales, sólidos suspendido totales, sólidos disueltos totales, demanda química de oxígeno (DQO), demanda bioquímica de oxígeno (DBO5), nitrógeno total (NTK) y fosforo total (PT). También se realizó la determinación del crecimiento de las plantas a partir del incremento de biomasa, porosidad de la raíz y de igual forma se determina NTK y PT. Los resultados demostraron que el sistema es una opción para la remoción de la carga orgánica y de nutrientes en aguas residuales de origen doméstico, de bajo costo de operación y mantenimiento, especialmente se observa que las plantas que crecen en sistemas de régimen de humedad ácuico y ústico, tienden a tener una mayor recepción y adaptación en los humedales artificiales pilotos, es el caso de la elefanta (Pennisetum purpureum), el cual presenta las más altas tasas de remoción de contaminantes y nutrientes en el afluente, seguido por el papiro japonés (Cyperus alternifolius) y el vetiver (Chrysopogon zizanioides), respecto a tasas de remoción. La remoción de contaminantes que se presentan más altos respectivamente, constituyen sólidos en primera instancia, seguido por la demanda bioquímica de oxigeno (DBO5), demanda química de oxígeno (DQO), nitrógeno total (NTK) y fósforo total (PT), estos últimos presentan una baja tasa de remoción, debido a la naturaleza misma del contaminante, a los organismos que realizan la remoción y absorción y al tiempo de retención que se elige, el cual influye en la tasa de remoción del contaminante siendo menor en la concentración de fósforo, pero se encuentranen el rango esperado para estos sistemas de tratamiento no convencionales.

Relations entre apports terrigènes et conchyliculture dans les Pertuis Charentais

This work presents interactions between quantitative and qualitative river freshwater inputs and the shellfish farming (oyster and mussel) in the Pertuis Charentais. The quantity of freshwater (i.e. salinity) seems to have a weak influence on the shellfish farming contrarily to its quality determined by particulate and dissolved matters contained in the water. In autumn and winter, large precipitations have a "globally positive" effect amending the coastal ecosystem. Associated dissolved nutriments and the organic matter largely determine the quality of the coming spring growth for bred shellfish, itself controlling in turn the annual yield efficiencies. However, in winter their effects are postponed because of strong mineral load, low luminosity and temperature, then limiting the primary production. The spring contributions, directly linked to territorial practices, agriculture and tourism are more variable in quantity and quality from one year to another. They often correspond to high-risk inflows since numerous substances from anthropogenic watersheds can be found diluted in the coastal zone as in the Pertuis Charentais. Their impacts on in situ estuarine ecosystems are still poorly known since these substances are mainly studied and estimated in laboratory in controlled conditions. Several studies showed anthropogenic contaminations (i.e. cadmium, pesticides) could have significant direct or indirect effects on shellfish farming. For instance, the "summer" mortalities between 1990 and 2000 in the South of the Marennes-Oléron bay (MOB), that induced environmental and physiological oyster disorders, could be linked to pesticide effects, measured during consecutive years on the oyster bed of Ronce Perquis in the South of the MOB. The weak results from the spring larval rearing of the IFREMER experimental hatchery in the South of the bay, and chromosomal abnormalities measured on the stocks of wild oysters of the Pertuis could confirm a high-risk spring environment for the shellfish farming. In summer terrestrial inputs are reduced by low precipitations, anthropogenic water removals (drinking water, irrigation) and by plant evapotranspiration. Consequently certain years, a significant salinity increase in water masses of the Pertuis Charentais is observed. However, based on long-term observations, the significant interannual variability noticed in freshwater contributions constitutes one of the most important facts of these last years. When contributions are weak (i.e. 1991 and 2011), the mean annual salinity is 34.5 in the MOB. To the contrary, other years (i.e. 1977, 1981, 1983 and 1988), the mean salinity reduced to 30.5 shows the significant freshwater contributions to the bay. Elsewhere, particularly in the mediterranean region, oyster breeding water conditions characterized by high salinity values show the freshwater does not seem to be necessary for biological functions of the Pacific oyster Crassostrea gigas. Indeed, the oyster embryonic life in particular is well adapted to high salinity values as long as trophic resources are substantial and temperatures remain high. These two factors firstly condition the embryonic survival before the water salinity. Besides, in the Pertuis Charentais, wind conditions and the geographical bloodstock position rather determine the success of the larvae capture than seawater physic-chemical conditions. Finally, a misunderstanding still remains on summer freshwater contributions to the oyster larvae food supply.