RF disturbances produced by high-power photovoltaic solar plants

In this thesis, analysis of electromagnetic compatibility of high-power photovoltaic solar plant is made. Current standards suitable for photovoltaic applications are given. Measurements of antenna factor for experimental setup are shown. Also, measurements of common mode disturbance voltages in high-power solar plant are given. Importance of DC-side filter is shown. In the last part of the work, electromagnetic simulations are made. These simulations show influence of several factors to EMC of power plant. Based on these simulations and measurements recommendations are given.

Variação estacional da radiação solar em ambiente externo e no interior de floresta semidecídua

Medições diárias de radiação solar global foram feitas, durante o período de junho de 2000 a janeiro de 2001, no interior de mata semidecídua e no ambiente exterior, tendo sido registrados valores médios de 1,1 e 19,3 MJ/m²/d, respectivamente. A transmissão de radiação solar para o interior da mata foi influenciada pela época do ano e variou de 3,3 a 8,2%, para o verão e o inverno. Equações de regressão, para estações do ano, foram desenvolvidas para estimar a radiação solar no interior da mata, em função de valores obtidos no ambiente externo.

Measurement and simulation of solar radiation availability in relation to the growth of coffee plants in an agroforestry system with rubber trees

Solar radiation is an important factor for plant growth, being its availability to understory crops strongly modified by trees in an Agroforestry System (AFS). Coffee trees (Coffea arabica - cv. Obatã IAC 1669-20) were planted at a 3.4 x 0.9 m spacing inside and aside rows of monocrops of 12 year-old rubber trees (Hevea spp.), in Piracicaba-SP, Brazil (22º42'30" S, 47º38'00" W - altitude: 546m). One-year-old coffee plants exposed to 25; 30; 35; 40; 45; 80; 90; 95 and 100% of the total solar radiation were evaluated according to its biophysical parameters of solar radiation interception and capture. The Goudriaan (1977) adapted by Bernardes et al. (1998) model for radiation attenuation fit well to the measured data. Coffee plants tolerate a decrease in solar radiation availability to 50% without undergoing a reduction on growth and LAI, which was approximately 2m².m-2 under this condition. Further reductions on the availability of solar radiation caused a reduction in LAI (1.5m².m-2), thus poor land cover and solar radiation interception, resulting in growth reduction.

MODELING AND SIMULATION OF RELIEF INFLUENCE ON EUCALYPTUS FORESTS: INTERACTION BETWEEN SOLAR IRRADIANCE AND PRODUCTIVITY

ABSTRACT This study aimed to verify the differences in radiation intensity as a function of distinct relief exposure surfaces and to quantify these effects on the leaf area index (LAI) and other variables expressing eucalyptus forest productivity for simulations in a process-based growth model. The study was carried out at two contrasting edaphoclimatic locations in the Rio Doce basin in Minas Gerais, Brazil. Two stands with 32-year-old plantations were used, allocating fixed plots in locations with northern and southern exposure surfaces. The meteorological data were obtained from two automated weather stations located near the study sites. Solar radiation was corrected for terrain inclination and exposure surfaces, as it is measured based on the plane, perpendicularly to the vertical location. The LAI values collected in the field were used. For the comparative simulations in productivity variation, the mechanistic 3PG model was used, considering the relief exposure surfaces. It was verified that during most of the year, the southern surfaces showed lower availability of incident solar radiation, resulting in up to 66% losses, compared to the same surface considered plane, probably related to its geographical location and higher declivity. Higher values were obtained for the plantings located on the northern surface for the variables LAI, volume and mean annual wood increase, with this tendency being repeated in the 3PG model simulations.

Estimativa da irradiação solar global com partição mensal e sazonal para a região de Cascavel - PR

No presente trabalho, mostram-se equações de estimativa da irradiação solar global (R G), por meio do modelo de Angstrom, com partições sazonal e mensal para a região de Cascavel - PR. Os dados experimentais foram cedidos pelo IAPAR, coletados na sua estação meteorológica localizada na COODETEC/Cascavel - PR, no período de 1983 a 1998. Dos 16 anos de dados, 12 anos foram utilizados para cálculo dos coeficientes (a e b) e quatro anos para a validação das equações. Os coeficientes de determinação encontrados foram superiores a 80% para as duas partições. O mínimo da R G é superestimado e o máximo é subestimado quando comparados com o mínimo e o máximo para dados reais, sendo esses encontrados no solstício de inverno e equinócio de primavera, respectivamente. A variação sazonal e mensal do coeficiente "a" foi menor (0,16 a 0,19 e 0,14 a 0,21) e do coeficiente "b" maior (0,34 a 0,43 e 0,32 a 0,44). As maiores variações dos erros médios diários ocorreram no equinócio de primavera (-19,45% a 27,28%) e as menores no equinócio de outono (-11,32% a 10,61%). O ajuste mais eficaz das equações foi encontrado para a partição mensal.

Avaliação de modelo matemático para estimar a radiação solar incidente sobre superfícies com diferentes exposições e declividades

Este trabalho teve por objetivo avaliar modelo matemático para estimar a radiação solar global diária sobre superfícies com diferentes exposições e declividades, no período de março de 2002 a março de 2003. A pesquisa foi desenvolvida em uma estrutura denominada "Bacia Hidrográfica Experimental" do Departamento de Engenharia Rural da UNESP, Câmpus de Jaboticabal - SP. Nessa estrutura, foram utilizadas superfícies caracterizadas como H, 10N, 10S, 20N, 20S, 10E, 10W, 20E e 20W. O sensor utilizado para medir a radiação solar global incidente nas superfícies estudadas foi um piranômetro da marca Kipp & Zonnen, modelo CM3. Para calcular a radiação solar incidente nas superfícies estudadas, foi utilizado o modelo de Kondratyev. As análises dos resultados foram feitas para o período diário, utilizando-se de análise de regressão e considerando o modelo linear (y = ax + b), na qual a variável dependente foi a radiação global medida (K¯M) e a radiação global calculada (K¯C) foi a variável independente. Os resultados deste estudo mostram que o modelo apresentou bons resultados para estimar a radiação nas superfícies H, 10N, 10S, 10E, 10W, 20E e 20W. Utilizando-se de dados de dias com céu límpido, foram obtidos os seguintes resultados: no inverno, o modelo foi preciso para estimar a radiação solar na superfície 20N, e apresentou resultados aceitáveis para estimar a radiação solar na superfície 20S.

APROS model validation in case of fast transients in a boiling water reactor

This Master´s thesis investigates the performance of the Olkiluoto 1 and 2 APROS model in case of fast transients. The thesis includes a general description of the Olkiluoto 1 and 2 nuclear power plants and of the most important safety systems. The theoretical background of the APROS code as well as the scope and the content of the Olkiluoto 1 and 2 APROS model are also described. The event sequences of the anticipated operation transients considered in the thesis are presented in detail as they will form the basis for the analysis of the APROS calculation results. The calculated fast operational transient situations comprise loss-of-load cases and two cases related to a inadvertent closure of one main steam isolation valve. As part of the thesis work, the inaccurate initial data values found in the original 1-D reactor core model were corrected. The input data needed for the creation of a more accurate 3-D core model were defined. The analysis of the APROS calculation results showed that while the main results were in good accordance with the measured plant data, also differences were detected. These differences were found to be caused by deficiencies and uncertainties related to the calculation model. According to the results the reactor core and the feedwater systems cause most of the differences between the calculated and measured values. Based on these findings, it will be possible to develop the APROS model further to make it a reliable and accurate tool for the analysis of the operational transients and possible plant modifications.

Análise de um sistema de aquecimento de água para residências rurais, utilizando energia solar

A conscientização da importância do meio ambiente tem incentivado o estudo de novas fontes energéticas renováveis e menos poluentes. Dentre essas fontes, a energia solar destaca-se por ser perene e limpa. A utilização da energia solar em sistemas de aquecimento de água residencial rural pode colaborar com a economia de energia elétrica, base da matriz energética brasileira. Conhecer os fatores que influenciam na operação de um sistema de aquecimento de água por energia solar é importante na determinação de sua viabilidade técnica, visando a sua difusão em residências rurais. Para tanto, construiu-se um protótipo, no câmpus da Faculdade Assis Gurgacz, em Cascavel - PR, com características similares a um equipamento utilizado em residências para dois habitantes, para funcionar com circulação natural ou termossifão e sem auxílio de sistema de aquecimento complementar. O equipamento mostrou-se viável tecnicamente, alcançando a temperatura mínima para banho de 35 °C, sempre que a radiação solar foi superior a 3.500 Wh m-2, o que aconteceu para a maioria dos dias estudados.

Evapotranspiração de referência com base na radiação solar global estimada pelo método de Bristow-Campbell

A quantidade de água a ser aplicada em sistemas de irrigação é normalmente calculada com base na evapotranspiração de referência (ETo) da região. Vários métodos podem ser empregados para o cálculo de ETo, sendo o de Hargreaves um dos mais adotados. Esse método utiliza valores estimados da radiação solar global (Rs) com base na diferença entre as temperaturas máxima (Tmáx) e mínima (Tmín) do ar. Entretanto, a Rs pode ser calculada por outros métodos, como o de Bristow-Campbell, que também se baseia na diferença entre Tmáx e Tmín. No presente trabalho, foram estimados valores diários da ETo pelo método de Hargreaves, em Jales - SP, com e sem o uso da equação de Bristow-Campbell para cálculo de Rs. Esses valores foram comparados aos obtidos pelo método de Penman-Monteith, que é considerado padrão para a estimativa de ETo. As avaliações consideraram os períodos úmido e seco na região. O uso da equação de Bristow-Campbell melhorou o desempenho do método de Hargreaves, em relação ao de Penman-Monteith, sendo que durante o período seco do ano o desempenho foi superior ao do período úmido.

Kinetic behavior of nitrification in the post-treatment of poultry wastewater in a sequential batch reactor

A sequential batch reactor with suspended biomass and useful volume of 5 L was used in the removal of nutrients and organic matter in workbench scale under optimal conditions obtained by central composite rotational design (CCRD), with cycle time (CT) of 16 h (10.15 h, aerobic phase, and 4.35 h, anoxic phase) and carbon: nitrogen ratio (COD/NO2--N+NO3--N) equal to 6. Complete cycles (20), nitrification followed by denitrification, were evaluated to investigate the kinetic behavior of degradation of organic (COD) and nitrogenated (NH4+-N, NO2--N and NO3--N) matter present in the effluent from a bird slaughterhouse and industrial processing facility, as well as to evaluate the stability of the reactor using Shewhart control charts of individual measures. The results indicate means total inorganic nitrogen (NH4+-N+NO2- -N+NO3--N) removal of 84.32±1.59% and organic matter (COD) of 53.65±8.48% in the complete process (nitrification-denitrification) with the process under statistical control. The nitrifying activity during the aerobic phase estimated from the determination of the kinetic parameters had mean K1 and K2 values of 0.00381±0.00043 min-1 and 0.00381±0.00043 min-1, respectively. The evaluation of the kinetic behavior of the conversion of nitrogen indicated a possible reduction of CT in the anoxic phase, since removals of NO2--N and NO3--N higher than 90% were obtained with only 1 h of denitrification.

Solar drying of jack fruit almonds

Dryers heated by solar energy have been constructed and used in drying whole and half jack fruit almonds. The samples were dried during the day in direct sun and in the conventional solar dryer prepared for this purpose. Another piece of equipment was built for reception and accumulation of sun energy in a body of water, which was used as a heat source for night drying. The drying with the sun energy was compared with artificial drying. The jack fruit almonds were dried whole, half, with pellicle and without it. The storage of solar energy in water was technically viable for use in night drying. The drying by combining solar dryers in the day and night periods were completed in approximately 35 hours, and were equivalent to artificial drying between 40ºC and 70ºC. Almond cut in half and the pellicle removed reduced the drying time.

Computer tools applied to analysis of solar water heaters

The simulation programs are important tools to analyze the different energetic alternatives, including the use of renewable energy. The objective of this study was to analyze comparatively the different computer tools available for modeling of solar water heaters. Among the main simulation software of solar thermal systems, there are: RETScreen International, EnergyPlus, TRNSYS, SolDesigner, SolarPro, e T*SOL. Among the tools mentioned, only EnergyPlus and RETScreen International are free, but they allow obtaining interesting results when applied together. The first one has a detailed module of energy analysis of solar water heaters, while the second one provides an detailed economic feasibility study and an assessment of emissions of greenhouse gases. RETScreen International and EnergyPlus programs are aimed at a diverse audience, including designers, researchers and energy planners.

Performance of an anaerobic-aerobic reactor and kinetic study of organic matter removal of cattle slaughterhouse effluent

This paper sought to evaluate the behavior of an upflow Anaerobic-Aerobic Fixed Bed Reactor (AAFBR) in the treatment of cattle slaughterhouse effluent and determine apparent kinetic constants of the organic matter removal. The AAFBR was operated with no recirculation (Phase I) and with 50% of effluent recirculation (Phase II), with θ of 11h and 8h. In terms of pH, bicarbonate alkalinity and volatile acids, the results indicated the reactor ability to maintain favorable conditions for the biological processes involved in the organic matter removal in both operational phases. The average removal efficiencies of organic matter along the reactor height, expressed in terms of raw COD, were 49% and 68% in Phase I and 54% and 86% in Phase II for θ of 11h and 8h, respectively. The results of the filtered COD indicated removal efficiency of 52% and k = 0.0857h-1 to θ of 11h and 42% and k = 0.0880h-1 to θ of 8h in the Phase I. In Phase II, the removal efficiencies were 59% and 51% to θ of 11h and 8h, with k = 0.1238h-1 and k = 0.1075 h-1, respectively. The first order kinetic model showed good adjustment and described adequately the kinetics of organic matter removal for θ of 11h, with r² equal to 0.9734 and 0.9591 to the Phases I and II, respectively.

Application of response surface methodology to study the biological removal of nitrogen from effluent of cattle slaughterhouse in a sequencing batch reactor

The aim of this study was to evaluate the efficiency of a sequencing batch reactor (SBR) on biological removal of nitrogen from cattle slaughterhouse wastewater by nitrification/denitrification processes. The effects of initial concentration of ammoniacal nitrogen were investigated at 100; 150 and 200 mg L-1 and air flow rate at 0.125; 0.375 and 0.625 L min¹ Lreactor-1 on the nitrogen compounds removal, by a Central Composite Rotational Design (CCRD) configuration. There were variations from 9.2 to 94.9%, 4.0 to 19.6% and 20.8 to 92.0% in the conversion of ammoniacal nitrogen to nitrate and nitrite concentration and removal of total nitrogen, respectively. The increase of air flow rate and decrease of the initial concentration of ammoniacal nitrogen resulted in higher efficiencies of total nitrogen removal, as well as the conversion of ammoniacal nitrogen to nitrate. During the pre-established intervals of this study, the removal and conversion efficiencies of nitrogen compounds above 85% were achieved in air flow rate variations from 0.375 to 0.725 L min-1 Lreactor-1 and initial concentration of ammoniacal nitrogen from 80 to 200 mg L-1. On denitrification process, we obtained efficiencies from 91.5 to 96.9% on the removal of nitrite/nitrate and from 78.3 to 87.9% on the removal of organic matter.

Solar energy use for water pre-heating in boilers of agro-industries

Energy consumption in the world has been growing every year. The industrial sector represents 27.32% of the world energy demand. Heating systems that use solar energy may contribute with a percentage of the total energy required by industries. This work aimed to study the use of vacuum solar collectors for water pre-heating in boilers. We used four collectors installed according to NBR 15,569; water flow through the tubes was 0.058 L/s, and temperature in the inlet and outlet pipes was measured. Results showed that instantaneous radiation, and inlet fluid and room temperatures are variables that influence the process, reaching water maximum temperature in the solar collector outlet of 97.9 °C, and efficiency of approximately 65% for most experiments. For the financial viability evaluation, the payback study was applied, which resulted in 4; 7 and 5 years, for the respective sources: firewood, LPG (liquefied petroleum gas), and electricity. Regarding the calculation of the annual contribution to the reduction of greenhouse gases, it was, respectively, 2.162 and 356 kg of CO2 per m² of collector tubes, in comparison with firewood and LPG.