Strategic planning of electricity systems: Integrating renewable energies

Tese de Doutoramento - Programa Doutoral em Engenharia Industrial e Sistemas (PDEIS)

OnBoard reconfigurable battery charger for electric vehicles with traction-to-auxiliary mode

This paper proposes a single-phase reconfigurable battery charger for Electric Vehicle (EV) that operates in three different modes: Grid-to-Vehicle (G2V) mode, in which the traction batteries are charged from the power grid; Vehicle-to-Grid (V2G) mode, in which the traction batteries deliver part of the stored energy back to the power grid; and in Traction-to-Auxiliary (T2A) mode, in which the auxiliary battery is charged from the traction batteries. When connected to the power grid, the battery charger works with sinusoidal current in the AC side, for both G2V and V2G modes, and also regulates the reactive power. When the EV is disconnected from the power grid, the control algorithms are modified and the full-bridge AC-DC bidirectional converter works as a full-bridge isolated DC-DC converter that is used to charge the auxiliary battery of the EV, avoiding the use of an additional charger to accomplish this task. To assess the behavior of the proposed reconfigurable battery charger under different operation scenarios, a 3.6 kW laboratory prototype has been developed and experimental results are presented.

Desenvolvimento de um filtro ativo paralelo monofásico compacto e didático utilizando MOSFETs

Dissertação de mestrado integrado em Engenharia Eletrónica Industrial e Computadores

Fundamental studies on natural deep eutectic solvents: physico-chemical, thermal and rheological properties

When combined at particular molar fractions, sugars, aminoacids or organic acids a present a high melting point depression, becoming liquids at room temperature. These are called Natural Deep Eutectic Solvents – NADES and are envisaged to play a major role on the chemical engineering processes of the future. Nonetheless, there is a significant lack of knowledge of its fundamental and basic properties, which is hindering their industrial applications. For this reason it is important to extend the knowledge on these systems, boosting their application development [1]. In this work, we have developed and characterized NADES based on choline chloride, organic acids, amino acids and sugars. Their density, thermal behavior, conductivity and polarity were assessed for different compositions. The conductivity was measured from 0 to 40 °C and the temperature effect was well described by the Vogel-Fulcher-Tammann equation. The morphological characterization of the crystallizable materials was done by polarized optical microscopy that provided also evidence of homogeneity/phase separation. Additionally, the rheological and thermodynamic properties of the NADES and the effect of water content were also studied. The results show these systems have Newtonian behavior and present significant viscosity decrease with temperature and water content, due to increase on the molecular mobility. The anhydrous systems present viscosities that range from higher than 1000Pa.s at 20°C to less than 1Pa.s at 70°C. DSC characterization confirms that for water content as high as 1:1:1 molar ratio, the mixture retains its single phase behavior. The results obtained demonstrate that the NADES properties can be finely tunned by careful selection of its constituents. NADES present the necessary properties for use as extraction solvents. They can be prepared from inexpensive raw materials and tailored for the selective extraction of target molecules. The data produced in this work is hereafter importance for the selection of the most promising candidates avoiding a time consuming and expensive trial and error phase providing also data for the development of models able to predict their properties and the mechanisms that allow the formation of the deep eutectic mixtures.

Potentially viable solar powered appliances cooling and distillation

Stand alone solar powered refrigeration and water desalination, two of the most popular and sought after applications of solar energy systems, have been selected as the topic of research for the works presented in this thesis. The water desalination system based on evaporation and condensation was found to be the most suitable one to be powered by solar energy. It has been established that highoutput fast-response solar heat collectors used to achieve high rates of evaporation and reliable solar powered cooling system for faster rates of condensation are the most important factors in achieving increased outputs in solar powered desalination systems. Comprehensive reviews of Solar powered cooling/refrigeration and also water desalination techniques have been presented. In view of the fact that the Institute of Technology, Sligo has a well-established long history of research and development in the production of state of the art high-efficiency fast-response evacuated solar heat collectors it was decided to use this know how in the work described in this thesis. For this reason achieving high rates of evaporation was not a problem. It was, therefore, the question of the solar powered refrigeration that was envisaged to be used in the solar powered desalination tofacilitate rapid condensation of the evaporated water that had to be addressed first. The principles of various solar powered refrigeration techniques have also been reviewed. The first step in work on solar powered refrigeration was to successfully modify a conventional refrigerator working on Platen-Munters design to be powered by highoutput fast-response evacuated solar heat collectors. In this work, which was the first ever successful attempt in the field, temperatures as low as —19°C were achieved in the icebox. A new approach in the use of photovoltaic technology to power a conventional domestic refrigerator was also attempted. This was done by modifying a conventional domestic refrigerator to be powered by photovoltaic panels in the most efficient way. In the system developed and successfully tested in this approach, the power demand has been reduced phenomenally and it is possible to achieve 48 hours of cooling power with exposure to just 7 hours of sunshine. The successful development of the first ever multi-cycle intermittent solar powered icemaker is without doubt the most exciting breakthrough in the work described in this thesis. Output of 74.3kg of ice per module with total exposure area of 2.88 m2, or 25.73kg per m2, per day is a major improvement in comparison to about 5-6kg of ice per m2 per day reported for all the single cycle intermittent systems. This system has then become the basis for the development of a new solar powered refrigeration system with even higher output, named the “composite” system described in this thesis. Another major breakthrough associated with the works described in this thesis is the successful development and testing of the high-output water desalination system. This system that uses a combination of the high-output fast-response evacuated solar heat collectors and the multi-cycle icemaker. The system is capable of producing a maximum of 141 litres of distilled water per day per module which has an exposure area of 3.24m2, or a production rate of 43.5 litres per m2 per day. Once again when this result is compared to the reported daily output of 5 litres of desalinated water per m per day the significance of this piece of work becomes apparent. In the presentation of many of the components and systems described in this thesis CAD parametric solid modelling has been used instead of photographs to illustrate them more clearly. The multi-cycle icemaker and the high-output desalination systems are the subject of two patent applications.

Putkilämmönsiirtimien mitoitustyökalujen kehittäminen

Diplomityön tarkoituksena on kehittää tietokoneohjelma putkilämmönsiirtimen vaippapuolen painehäviön laskemiseksi. Ohjelmalla voidaan varmistaa lämmönsiirtimen mitoitusvaiheessa, että vaippapuolen painehäviö ei ylitä sallittuja rajoja. Ohjelmatäydentää olemassa olevia mitoitusohjelmia. Tässä diplomityössä käsitellään ainoastaan höyryvoimalaitosprosesseissa käytettäviä putkilämmönsiirtimiä. Työn kirjallisessa osassa on selvitetty periaate höyryvoimalaitosprosessista ja siinä käytettävistä putkilämmönsiirtimistä sekä esitetty putkilämmönsiirtimien rakenne, yleinen suunnittelu ja lämpö- ja virtaustekninen mitoitus. Painehäviön laskennassa käytetyt ja lämpö- ja virtausteknistä mitoitusta käsittelevässä kappaleessa esitetyt yhtälöt perustuvat Bell-Delawaren menetelmään. Painehäviönlaskentaohjelma on toteutettu hyväksikäyttäen Microsoft Excel taulukkolaskentaa ja Visual Basic -ohjelmointikieltä. Painehäviön laskenta perustuu segmenttivälilevyillä varustetun putkilämmönsiirtimen vaippapuolen yksifaasivirtaukseen. Lämmönsiirtimen lauhdutinosan painehäviö oletetaan merkityksettömäksi, joten kokonaispainehäviö muodostuu höyryn- ja lauhteenjäähdyttimessä. Kehitetty ohjelma on suunniteltu erityisesti lauhteenjäähdyttimessä muodostuvan painehäviön laskentaan. Ohjelmalla laskettuja painehäviön arvoja on verrattu todellisesta lämmönsiirtimestä mitattuihin arvoihin. Lasketut arvotvastaavat hyvin mittaamalla saatuja, eikä tuloksissa ilmene mitään systemaattista virhettä. Ohjelma on valmis käytettäväksi putkilämmönsiirtimien mitoitustyökaluna. Diplomityön pohjalta on tehty ehdotukset ohjelman edelleen kehittämiseksi.

Analysis of the voltage source inverter with small DC-link capacitor

IIn electric drives, frequency converters are used to generatefor the electric motor the AC voltage with variable frequency and amplitude. When considering the annual sale of drives in values of money and units sold, the use of low-performance drives appears to be in predominant. These drives have tobe very cost effective to manufacture and use, while they are also expected to fulfill the harmonic distortion standards. One of the objectives has also been to extend the lifetime of the frequency converter. In a traditional frequency converter, a relatively large electrolytic DC-link capacitor is used. Electrolytic capacitors are large, heavy and rather expensive components. In many cases, the lifetime of the electrolytic capacitor is the main factor limiting the lifetime of the frequency converter. To overcome the problem, the electrolytic capacitor is replaced with a metallized polypropylene film capacitor (MPPF). The MPPF has improved properties when compared to the electrolytic capacitor. By replacing the electrolytic capacitor with a film capacitor the energy storage of the DC-linkwill be decreased. Thus, the instantaneous power supplied to the motor correlates with the instantaneous power taken from the network. This yields a continuousDC-link current fed by the diode rectifier bridge. As a consequence, the line current harmonics clearly decrease. Because of the decreased energy storage, the DC-link voltage fluctuates. This sets additional conditions to the controllers of the frequency converter to compensate the fluctuation from the supplied motor phase voltages. In this work three-phase and single-phase frequency converters with small DC-link capacitor are analyzed. The evaluation is obtained with simulations and laboratory measurements.

Development of a PC Tool for Estimating Pressure Drops in Forced-convection Boiler Tubes

Kaksifaasivirtauksen kuvaamiseen käytettävät mallit, ja menetelmät kaksifaasivirtauksen painehäviön määrittämiseksi kehittyvät yhä monimutkaisimmiksi. Höyrystinputkissa tapahtuvien painehäviöiden arvioinnin vaatiman laskennan suorittamiseksi tietokoneohjelman kehittäminen on välttämätöntä. Tässä työssä on kehitetty itsenäinen PC-ohjelma painehäviöiden arvioimiseksi pakotetulle konvektiovirtaukselle pystysuorissa höyrykattilan höyrystinputkissa. Veden ja vesihöyryn aineominaisuuksien laskentaan käytetään IAPWS-IF97 –yhtälökokoelmaa sekä muita tarvittavia IAPWS:n suosittelemia yhtälöitä. Höyrystinputkessa kulloinkin vallitsevan virtausmuodon määrittämiseen käytetään sovelluskelpoisia virtausmuotojen välisiä rajoja kuvaavia yhtälöitä. Ohjelmassa käytetään painehäviön määritykseen kirjallisuudessa julkaistuja yhtälöitä, virtausmuodosta riippuen, alijäähtyneelle virtaukselle, kupla-, tulppa- ja rengasvirtaukselle sekä tulistetun höyryn virtaukselle. Ohjelman laskemia painehäviöarvioita verrattiin kirjallisuudesta valittuihin mittaustuloksiin. Laskettujen painehäviöiden virhe vaihteli välillä –19.5 ja +23.9 %. Virheiden itseisarvojen keskiarvo oli 12.8 %.

Extração líquido-líquido em sistemas de fluxo

This review deals with principles of the liquid-liquid extraction, when performed in flow systems. This approach is frequently used for sample treatment to improve the selectivity and/or sensitivity in analytical measurements. The advances in this area are reported, including the use of monosegmented flow systems to perform metal extraction through both two-phase and single phase processes.

Grounding in a wind power application

The subject of this master’s thesis is to research grounding in a particular wind power application. The aim is to define how the grounding from different points effects to the function of the whole system. The investigated subjects are generator voltage spikes, ground currents and system fault situations. The first part of this thesis represents power electronics, which is commonly used in wind power systems. The second part concentrates more to the grounding, electrical safety demands and potential fault situations. The object of the simulations is to investigate voltage spikes and fault situations. Measurements will be made with small-scale setup and in the last part simulation and measurement results are compared to each other and to a full-scale system.

Role of references in international industrial marketing : a theory-building case study about supplier’s processes of utilizing references

Scientific studies regarding specifically references do not seem to exist. However, the utilization of references is an important practice for many companies involved in industrial marketing. The purpose of the study is to increase the understanding about the utilization of references in international industrial marketing in order to contribute to the development of a theory of reference behavior. Specifically, the modes of reference usage in industry, the factors affecting a supplier's reference behavior, and the question how references are actually utilized, are explored in the study. Due to the explorative nature of the study, a research design was followed where theory and empirical studies alternated. An Exploratory Framework was developed to guide a pilot case study that resulted in Framework 1. Results of the pilot study guided an expanded literature review that was used to develop first a Structural Framework and a Process Framework which were combined in Framework 2. Then, the second empirical phase of the case study was conducted in the same (pilot) case company. In this phase, Decision Systems Analysis (DSA) was used as the analysis method. The DSA procedure consists of three interviewing waves: initial interviews, reinterviews, and validating interviews. Four reference decision processes were identified, described and analyzed in the form of flowchart descriptions. The flowchart descriptions were used to explore new constructs and to develop new propositions to develop Framework 2 further. The quality of the study was ascertained by many actions in both empirical parts of the study. The construct validity of the study was ascertained by using multiple sources of evidence and by asking the key informant to review the pilot case report. The DSA method itself includes procedures assuring validity. Because of the choice to conduct a single case study, external validity was not even pursued. High reliability was pursued through detailed documentation and thorough reporting of evidence. It was concluded that the core of the concept of reference is a customer relationship regardless of the concrete forms a reference might take in its utilization. Depending on various contingencies, references might have various tasks inside the four roles of increasing 1) efficiency of sales and sales management, 2) efficiency of the business, 3) effectiveness of marketing activities, and 4) effectiveness in establishing, maintaining and enhancing customer relationships. Thus, references have not only external but internal tasks as well. A supplier's reference behavior might be affected by many hierarchical conditions. Additionally, the empirical study showed that the supplier can utilize its references as a continuous, all pervasive decision making process through various practices. The process includes both individual and unstructured decision making subprocesses. The proposed concept of reference can be used to guide a reference policy recommendable for companies for which the utilization of references is important. The significance of the study is threefold: proposing the concept of reference, developing a framework of a supplier's reference behavior and its short term process of utilizing references, and conceptual structuring of an unstructured and in industrial marketing important phenomenon to four roles.

Tasasähkönjakeluverkon asiakaspäätelaitteen galvaanisen erotuksen toteuttaminen

Tässä työssä tutkitaan LLC resonanssipiirin soveltuvuutta galvaanisen erotuksen toteuttamiseen tasasähkönjakeluverkon asiakaspäätelaitteessa. Tarkastellaan resonanssipiirin ominaisuuksia ja aikaisempia käyttökohteita. Tutkitaan piirin soveltuvuutta vaihtosähkö sovellukseen ja esitellään piirin toimintaa, häviöitä ja ohjausta. Esitellään pulssin leveys moduloitu (PWM) ja pulssin tiheys moduloitu (PDM) invertteri sovellukset ja näiden toimintaa. Esitetään vielä parannusehdotuksia ja kytkentäkuvio kytkennän ominaisuuksien ja hyö-tysuhteen parantamiseksi. Tutkimuksessa selvisi, että suora PDM topologia ei sovellu tähän käyttötarkoitukseen suuren suodin induktanssin vuoksi. PWM invertteri topologia jännitteen tasasuuntauksella taas sopii sovellukseen ja tällä rakenteella on mahdollista tehdä galvaaninen erotus hyvinkin hyvällä hyötysuhteella. Pehmeän kytkennän aiheuttamien häviöiden tarkka määrittely simulointimallista on parhaimmillaankin vain suuntaa-antava, mutta tulokset olivat mielestäni oikein positiivisia. LLC resonanssipiirin toimintaa tutkittiin vain resonanssitaajuudella kytkettäessä, jolloin sen jännitevahvistusominaisuuksien hyödyntäminen jää tarkastelun ulko-puolelle.

Chelyabinsk CHP-3 “locked power” problem solving

All over the world power systems become bigger and bigger every day. New equipment is installed, new feeders are constructed, new power units are installed. Some old elements of the network, however, are not changed in time. As a result, “bottlenecks” for capacity transmission can occur. By locked power problem the situation when a power plant has installed capacity exceeding the power it can actually deliver is usually meant. Regime, scheme or even technical restrictions-related issues usually cause this kind of problem. It is really important, since from the regime point of view it is typical decision to have a mobile capacity reserve, in case of malfunctions. And, what can be even more significant, power plant owner (JSC Fortum in our case) losses his money because of selling less electrical energy. The goal of master`s thesis is to analyze the current state of Chelyabinsk power system and the CHP-3 (Combined Heat and Power plant) in particular in relation with it`s ability to deliver the whole capacity of the CHP in it`s existing state and also taking into consideration the prospect of power unit 3 installation by the fourth quarter of 2010. The thesis contains some general information about the UPS of Russia, CPS of Ural, power system of Chelyabinsk and the Chelyabinsk region itself. Then the CHP-3 is described from technical point of view with it`s equipment observation. Regimes for the nowadays power system and for the system after the power unit 3 installation are reviewed. The problems occurring are described and, finally, a solution is offered.

Bubble-Bubble Interaction in Horizontal Two-Phase Slug Flow

Modelling of the slug structure requires a new effort on fundamental research. To clarify some aspects of the horizontal slug flow, an experimental study of the behaviour of two isolated bubbles in a single-phase liquid flow was performed. This procedure was adopted to avoid the overlap of different phenomena induced by a train of long bubbles. The experimental facility consists of a 90-m horizontal PVC pipe with internal diameter of 0,053 m. The behaviour of two single air bubbles travelling in a water flow was studied. Focus was given on the influence of the distance between the bubbles on the velocity of the second bubble. This study allows the understanding of the mechanism of overtaking that takes place right after the slug formation and that precedes the coalescence of bubbles in a slug flow. The results show that bubbles placed behind a liquid slug smaller than a critical value move faster than the leading one. Otherwise, they move slower than the leading one.