Influence of pH on the incorporation and growth of Pb(2)CrO(5) crystallites in silica matrix

Pb(2)CrO(5) nanoparticles were embedded in an amorphous SiO(2) matrix by the sol-gel process. The pH and heat treatment effects were evaluated in terms of structural, microstructural and optical properties from Pb(2)CrO(5)/SiO(2) compounds. X-ray diffraction (XRD), high resolution transmission electron microscopy (HR-TEM), energy dispersive spectroscopy (EDS), and diffuse reflectance techniques were employed. Kubelka-Munk theory was used to calculate diffuse reflectance spectra that were compared to the experimental results. Finally, colorimetric coordinates of the Pb(2)CrO(5)/SiO(2) compounds were shown and discussed. In general, an acid pH initially dissolves Pb(2)CrO(5) nanoparticles and following heat treatment at 600 A degrees C crystallized into PbCrO(4) composition with grain size around 6 nm in SiO(2) matrix. No Pb(2)CrO(5) solubilization was observed for basic pH. These nanoparticles were incorporated in silica matrix showing a variety of color ranging from yellow to orange.

Magnetic resonance study of a vanadium pentoxide gel

In this work we report results from continuous-wave (CW) and pulsed electron paramagnetic resonance (EPR) and proton nuclear magnetic resonance (NMR) studies of the vanadium pentoxide xerogel V2O5:nH(2)O (n approximate to 1.6). The low temperature CW-EPR spectrum shows hyperfine structure due to coupling of unpaired V4+ electron with the vanadium nucleus. The analysis of the spin Hamiltonian parameters suggests that the V4+ ions are located in tetragonally distorted octahedral sites. The transition temperature from the rigid-lattice low-temperature regime to the high temperature liquid-like regime was determined from the analysis of the temperature dependence of the hyperfine splitting and the V4+ motional correlation time. The Electron Spin Echo Envelope Modulation (ESEEM) data shows the signals resulting from the interaction of H-1 nuclei with V4+ ions. The modulation effect was observed only for field values in the center of the EPR absorption spectrum corresponding to the single crystals orientated perpendicular to the magnetic field direction. At least three protons are identified in the xerogel by our magnetic resonance experiments: (I) the OH groups in the equatorial plane, (ii) the bound water molecules in the axial V=O bond and (iii) the free mobile water molecules between the oxide layers. Proton NMR lineshapes and spin-lattice relaxation times were measured in the temperature range between 150 K and 323 K. Our analysis indicates that only a fraction of the xerogel protons contribute to the measured conductivity.

External polyacrylate-coating as alternative material for preparation of photopolymerized sol-gel monolithic column

Photopolymerized sol-gel monolithic columns for use in capillary electrochromatography were prepared in 125 mu m i.d. polyacrylate-coated fused-silica capillaries. The polyacrylate-coating, unlike the polyimide one, is transparent to the radiation used (approximate to 370 nm), and thus, no coating removal is necessary. This is a very important particularity since intrinsic capillary column characteristics, such as flexibility and mechanical resistance, are unchanged. A mixture containing metacryloxypropyltrimethoxysilane (MPTMS) as the polymeric precursor, hydrochloric acid as the catalyst, toluene as the porogen and bis(2,4,6-trimethylbenzoyl)-phenylphosphine oxide (Irgacure 819) as the photoinitiator was irradiated at 370 nm for 20 min inside the capillaries to prepare the columns through sol-gel approach. The versatility and viability of the use of polyacrilate as a new capillary external coating were shown through preparation of two columns under different conditions, which were tested in electrochromatography for separation of standard mixture containing thiourea (marker compound), propylbenzene, phenanthrene and pyrene. (C) 2008 Elsevier B.V. All rights reserved.

Anticorrosive cerium-based coatings prepared by the sol-gel method

The development of efficient anti-corrosion and environmentally friendly coating systems are needed for the replacement of the highly toxic Cr-based conversion coatings for corrosion protection of aluminum alloys. In this study, we demonstrate that the direct application of ceramic cerium-based sol-gel coatings to AA7075-T6 substrates produces high-performance anti-corrosion layers. Electrochemical experiments and analyses of the microstructure demonstrate that the protective layers are very efficient for the passivation of the alloy surfaces operating as both passive and active barrier for corrosion protection.

Monitoramento morfológico do xerogel híbrido 3-(1,4-fenilenodiamina)propil/silica obtido sob diferentes condições de síntese

Neste trabalho, foi obtido o xerogel híbrido 3-(1,4-fenilenodiamina) propil/sílica, usando-se o método sol-gel de síntese, variando-se as condições experimentais de síntese. Foram usados como reagentes precursores o tetraetilortosilicato (TEOS) e o 3-[(1,4-fenilenodiamina)propil]trimetoxisilano (FDAPS) sintetizado em nosso laboratório. As condições experimentais de síntese variadas foram: a concentração de precursor orgânico (FDAPS), a temperatura de gelificação, o tipo de solvente e o pH do meio reacional. O trabalho foi dividido em duas etapas: na primeira, foram obtidas duas séries de materiais onde se variou a temperatura de gelificação (5, 25, 50 e 70 °C), além da quantidade de precursor orgânico (FDAPS), adicionado à síntese (1,5 e 5,0 mmol). Na segunda etapa variou-se o pH do meio reacional (4, 7 e 10) além do tipo de solvente (etanol, butanol e octanol), mantendo-se a quantidade de precursor orgânico adicionado e a temperatura de gelificação constantes em 5,0 mmol e 25 oC, respectivamente. Em ambas etapas utilizou-se HF como catalisador e manteve-se o sistema fechado, porém não vedado, durante a gelificação. Na caracterização dos xerogéis híbridos foram usadas as seguintes técnicas: a) termoanálise no infravermelho, para estimar a estabilidade térmica do componente orgânico além da fração de orgânicos dispersos na superfície; b) isotermas de adsorção e dessorção de nitrogênio, para determinação da área superficial específica, do volume e da distribuição de tamanho de poros; c) análise elementar para estimar a fração de componente orgânico presente no xerogel e d) microscopia eletrônica de varredura onde foi possível observar textura, compactação e presença de partículas primárias nos xerogéis. A partir dos resultados de caracterização foi possível avaliar a influência dos parâmetros experimentais de síntese nas características dos xerogéis híbridos obtidos. Xerogéis híbridos com maior teor de orgânicos foram mais influenciados pela variação da temperatura de gelificação. Um aumento na temperatura de gelificação produz xerogéis com menor porosidade, entretanto, com maior estabilidade térmica do componente orgânico. Considerando-se estabilidade térmica e porosidade, as amostras gelificadas a 25 oC apresentaram os melhores resultados. Em relação à variação de pH e solvente, as amostras gelificadas em pH ácido foram as que apresentaram maior porosidade, enquanto que a maior estabilidade térmica foi alcançada usando-se etanol como solvente.

Electrochemical study of o-toluidine blue impregnated in mesoporous silica channels

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Bacterial cellulose-silica organic-inorganic hybrids

Bacterial cellulose (BC) hydrated membranes present nanometric reticulated structure that can be used as a template in the preparation of new organic-inorganic hybrids. BC-silica hybrids were prepared from BC membranes and tetraethoxysilane, (TEOS) at neutral pH conditions at room temperature. Macroscopically homogeneous membranes were obtained containing up to 66 wt.% of silica spheres, 20-30 nm diameter. Scanning electron micrographs clearly show the silica spheres attached to cellulose microfibrils. By removing the cellulose, the silica spheres can be easily recovered. The new hybrids are stable up to 300 degrees C and display a broad emission band under UV excitation assigned to oxygen-related defects at the silica particles surface. Emission color can be tuned by changing the excitation wavelength.

Investigation about the copper adsorption on the chloropropylsilica gel surface modified with a nanostructured dendrimer DAB-Am-16: an analytical application for determination of copper in different samples

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fractal character of the SAXS correlation volume in poly(ethylene glycol)/silica hybrid wet gels

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Dynamic Scaling and Growth Kinetics of 3-Glycidoxypropyltrimethoxysilane-Derived Organic/Silica Hybrids

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Nanopore size growth and ultrafiltration performance of SnO2 ceramic membranes prepared by sol-gel route

Supported ceramic membranes have been produced by the sol-casting procedure from aqueous colloidal suspensions prepared by the sol-gel route. Coatings on a tubular alumina support have been successfully performed leading to crack free layers. Samples have been sintered at 400, 500 and 600 degreesC, and the effect of heating treatment on the nanostructure and on the ultrafiltration properties are analyzed. The characterization has been done by high resolution scanning electron microscopy, nitrogen adsorption-desorption isotherms, water permeation and cut-off determination using polyethylene glycol standard solutions. The micrographs have revealed that grains and pore size increase with the temperature, whereas their shape remains invariant. This results is in agreements with N-2 adsorption-desorption analyses, which have revealed that the mean pore size diameter increases from 4 to 10 nm as the sintering temperature increases from 400 to 600 degreesC, while the total porosity remains constant. Furthermore, the tortuosity, calculated from water permeability, is essentially invariant with the sintering temperatures. The membranes cut-off, determined with a retention rate equal to 95%, are 3500, 6500 and 9000 g . mol(-1) for 400, 500 and 600 degreesC, respectively, showing that the permeation properties of SnO2 ultrafiltration membranes can easily be controlled by sintering condition.

NiTiO3 nanoparticles encapsulated with SiO2 prepared by sol-gel method

NiTiO3 (NTO) nanoparticles encapsulated with SiO2 were prepared by the sol-gel method resulting on core-shell structure. Changes on isoelectric point as a function of silica were evaluated by means of zeta potential. The NTO nanoparticles heat treated at 600 degrees C were characterized by X-ray diffraction, transmission electron microscopy (TEM) and energy dispersive X-ray analysis. TEM observations showed that the mean size of NTO is in the range of 2.5-42.5 nm while the thickness of SiO2 shell attained 1.5-3.5 nm approximately.

External polyacrylate-coating as alternative material for preparation of photopolymerized sol-gel monolithic column

Photopolymerized sol-gel monolithic columns for use in capillary electrochromatography were prepared in 125 mu m i.d. polyacrylate-coated fused-silica capillaries. The polyacrylate-coating, unlike the polyimide one, is transparent to the radiation used (approximate to 370 nm), and thus, no coating removal is necessary. This is a very important particularity since intrinsic capillary column characteristics, such as flexibility and mechanical resistance, are unchanged. A mixture containing metacryloxypropyltrimethoxysilane (MPTMS) as the polymeric precursor, hydrochloric acid as the catalyst, toluene as the porogen and bis(2,4,6-trimethylbenzoyl)-phenylphosphine oxide (Irgacure 819) as the photoinitiator was irradiated at 370 nm for 20 min inside the capillaries to prepare the columns through sol-gel approach. The versatility and viability of the use of polyacrilate as a new capillary external coating were shown through preparation of two columns under different conditions, which were tested in electrochromatography for separation of standard mixture containing thiourea (marker compound), propylbenzene, phenanthrene and pyrene. (C) 2008 Elsevier B.V. All rights reserved.

Influência da catálise ácida e básica na preparação da sílica funcionalizada pelo método sol-gel

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Thermogravimetric investigations during the synthesis of silica-based MCM-41

MCM-41 material was synthesized starting from hydrogel containing colloidal fumed silica, sodium silicate, cetyltetramethylammonium bromide (CTMABr) as surfactant, and distilled water as solvent. These reactants were mixed to obtain a gel with the following composition: 4SiO(2):1Na(2)O:1CTMABr:200H(2)O. The hydrogel with pH=14 was hydrothermally treated at 100 degreesC, for 4 days. Each day, the pH was measured, and then adjusted to 9.5-10 by using 30% acetic acid solution. Thermogravimetry was the main technique, which was used to monitor the participation of the surfactant on the MCM-41 nanophase, being possible to determine the temperature ranges relative to water desorption as well as the surfactant decomposition and silanol condensation.