Analysis and modelling of chemical looping combustion process with and without oxygen uncoupling

Effective control and limiting of carbon dioxide (CO₂) emissions in energy production are major challenges of science today. Current research activities include the development of new low-cost carbon capture technologies, and among the proposed concepts, chemical combustion (CLC) and chemical looping with oxygen uncoupling (CLOU) have attracted significant attention allowing intrinsic separation of pure CO₂ from a hydrocarbon fuel combustion process with a comparatively small energy penalty. Both CLC and CLOU utilize the well-established fluidized bed technology, but several technical challenges need to be overcome in order to commercialize the processes. Therefore, development of proper modelling and simulation tools is essential for the design, optimization, and scale-up of chemical looping-based combustion systems. The main objective of this work was to analyze the technological feasibility of CLC and CLOU processes at different scales using a computational modelling approach. A onedimensional fluidized bed model frame was constructed and applied for simulations of CLC and CLOU systems consisting of interconnected fluidized bed reactors. The model is based on the conservation of mass and energy, and semi-empirical correlations are used to describe the hydrodynamics, chemical reactions, and transfer of heat in the reactors. Another objective was to evaluate the viability of chemical looping-based energy production, and a flow sheet model representing a CLC-integrated steam power plant was developed. The 1D model frame was succesfully validated based on the operation of a 150 kWth laboratory-sized CLC unit fed by methane. By following certain scale-up criteria, a conceptual design for a CLC reactor system at a pre-commercial scale of 100 MWth was created, after which the validated model was used to predict the performance of the system. As a result, further understanding of the parameters affecting the operation of a large-scale CLC process was acquired, which will be useful for the practical design work in the future. The integration of the reactor system and steam turbine cycle for power production was studied resulting in a suggested plant layout including a CLC boiler system, a simple heat recovery setup, and an integrated steam cycle with a three pressure level steam turbine. Possible operational regions of a CLOU reactor system fed by bituminous coal were determined via mass, energy, and exergy balance analysis. Finally, the 1D fluidized bed model was modified suitable for CLOU, and the performance of a hypothetical 500 MWth CLOU fuel reactor was evaluated by extensive case simulations.

A morphometric study of the lumbar spinous process in the Chinese population

Our goal was to analyze the anatomical parameters of the lumbar spine spinous process for an interspinous stabilization device designed for the Chinese population and to offer an anatomical basis for its clinical application. The posterior lumbar spines (T12-S1) of 52 adult cadavers were used for measuring the following: distance between two adjacent spinous processes (DB), distance across two adjacent spinous processes (DA), thickness of the central spinous processes (TC), thickness of the superior margin of the spinous processes (TS), thickness of the inferior margin of the spinous processes (TI), and height of the spinous processes (H). Variance and correlation analyses were conducted for these data, and the data met the normal distribution and homogeneity of variance. DB decreased gradually from L1-2 to L5-S1. DA increased from T12-L1 to L2-3 and then decreased from L2-3 to L4-5. The largest H in males was noted at L3 (25.45±5.96 mm), whereas for females the largest H was noted at L4 (18.71±4.50 mm). Usually, TS of the adjacent spinous process was lower than TI. Based on the anatomical parameters of the lumbar spinous processes obtained in this study, an “H”-shaped coronal plane (posterior view) was proposed as an interspinous stabilization device for the Chinese population. This study reports morphometric data of the lumbar spinous processes in the Chinese population, which provides an anatomical basis for future clinical applications.

Study of clarification process of sugar cane juice for consumption

Sugar cane juice or garapa darkens quickly after extraction due to the oxidation of some of its constituents harming its commercialization thus requiring rapid consumption. The objective of this study was to develop a mild process for sugar cane clarification, obtaining a cloudy, greenish-yellow beverage. The following parameters were combined to aiming at this objective: heat treatment at 65 ºC/50 minutes; pH change (to 7.0, 7.5, and 8.0); addition of flocculant (0, 30, and 60 ppm Aluminum polychloride or APC - "Panclar P-1010"), and clarifier aid (0, 2, or 4 ppm of positively charged polyelectrolyte - "Magnafloc LT-27"). The decantation time was 45 minutes and the supernatant liquid was removed with a vacuum pump. The treatments were defined using the Response Surface Methodology and were submitted to physicochemical analysis for turbidity (%), total polysaccharide content (µg.mL-1), dextran content (µg.mL-1), and sensory analysis (acceptance test) for the attributes of color, appearance, and turbidity. It was concluded that the addition of 60 ppm APC, pH 8, and 0 ppm polyelectrolyte represented the best treatment to obtain a low polysaccharide content, 90% turbidity, and high scores for color, appearance, and turbidity. The beverage was sensorially well accepted by consumers.

Process variables in the osmotic dehydration of sliced peaches

This paper evaluated the influence of temperature and concentration of the sucrose syrup on the pre-osmotic dehydration of peaches. Physical (colour and texture) and chemical variables (soluble solid content; total sugar, reducing and non-reducing sugar contents; and titratable acidity) were investigated, as well as the osmotic dehydration parameters (loss of weight and water; solids incorporation). An experimental central composite design was employed varying the temperature (from 30 to 50 ºC) and concentration (from 45 to 65 ºBrix) and maintaining the syrup to fruit ratio (4:1), process time (4 hours), and format (slices). The degree of acceptance was used in the sensory analysis evaluating the following characteristics: appearance, taste, texture, colour, and overall quality using a hedonic scale. The results were modelled using the Statistica program (v. 6.0) and the Response Surface Methodology. The mathematical models of the following dimensionless variations yielded significant (p < 0.05) and predictive results: soluble solids content, total and non-reducing sugar contents, titratable acidity, colour parameter L*, and water loss. The models of the attributes colour and appearance yielded significant (p < 0.10) but not predictive results. Temperature was the prevalent effect in the models. The process conditions in the range from 50 to 54.1 ºC and from 45 to 65 ºBrix led to greater water losses and better sensory performances.

Determination of thermobacteriological parameters and size of Bacillus stearothermophilus ATCC 7953 spores

In order to determine thermobacteriological parameters for B. stearothermophilus spores, they were diluted in a saline solution medium and in ground corn-soybean mix, distributed in TDT tube, and submitted to heat for a specific period of time. The D value (time to reduce 1 log cycle of microbial count under a certain temperature) and z value (variation of temperature to cause 10-fold change in D value) were estimated. To estimate their dimensions, the spores were visualized by using a scanning electron microscope. D121.1 ºC and z values for these spores, as determined in the saline solution, were 8.8 minutes and 12.8 ºC, respectively. D121,1 ºC and z values determined in the corn-soy mix were 14.2 minutes and 23.7 ºC, respectively. The micrographs indicated that the spores have homogeneous shape and size, with length and diameter of 2 and 1 µm, respectively. These results confirm that the spore is highly thermal-resistant, and it is a good biological indicator to evaluate the extrusion process as a feed sterilizer.

Effects of the mechanical damage on the water absorption process by corn kernel

The purpose of this study was to investigate and model the water absorption process by corn kernels with different levels of mechanical damage Corn kernels of AG 1510 variety with moisture content of 14.2 (% d.b.) were used. Different mechanical damage levels were indirectly evaluated by electrical conductivity measurements. The absorption process was based on the industrial corn wet milling process, in which the product was soaked with a 0.2% sulfur dioxide (SO2) solution and 0.55% lactic acid (C3H6O3) in distilled water, under controlled temperatures of 40, 50, 60, and 70 ºC and different mechanical damage levels. The Peleg model was used for the analysis and modeling of water absorption process. The conclusion is that the structural changes caused by the mechanical damage to the corn kernels influenced the initial rates of water absorption, which were higher for the most damaged kernels, and they also changed the equilibrium moisture contents of the kernels. The Peleg model was well adjusted to the experimental data presenting satisfactory values for the analyzed statistic parameters for all temperatures regardless of the damage level of the corn kernels.

Physicochemical and microbiological parameters of dried salted pork meat with different sodium chloride levels

The objective of this study was to evaluate the physicochemical and microbiological parameters of pork meat submitted to dry salting. Sodium chloride (NaCl) was added at levels of 0%, 2.5%, 5%, 7.5% or 10% by the meat weight. Dry salting technique was used, which consists of rubbing the sodium chloride manually, followed by a rest period. The data were submitted to analysis of variance using a completely randomized experimental design. The means were compared by Duncan test at 5%. The salting process reduced (P < 0.05) humidity and water activity, and it increased (P < 0.05) ash, chloride, palmitic acid, and water holding capacity levels compared to those of the control. Luminosity (L*) was lower (P < 0.05) in the control, and a* color was more intense in samples with 2.5% NaCl. Cooking loss was lower (P < 0.05) in the samples salted with 5% and 10% NaCl, and similarity was observed between the levels 0 and 7.5% salt. The treatments with levels 0% and 2.5% NaCl had higher mesophilic counts. The other microbiological parameters were within limits established by law. Therefore, salting with 5% NaCl can be used in pork meat in order to maintain the physicochemical and microbiological characteristics of the final product.

Spirulina platensis: process optimization to obtain biomass

Spirulina platensis is a photoautotrophic mesophilic cyanobacterium. Its main sources of nutrients are nitrate, urea, and ammonium salts. Spirulina cultivation requires temperature, light intensity, and nutrient content control. This microalgae has been studied and used commercially due to its therapeutic and antioxidant potential. In addition, several studies have reported its ability to use CO2, its immune activity, and use as an adjuvant nutritive factor in the treatment of obesity. The objective of this study is the production of biomass of S. platensis using different rates of stirring, nitrogen source, amount of micronutrients, and luminosity. A 2(4) experimental design with the following factors: stirring (120 and 140 RPM), amount of nitrogen (1.5 and 2.5 g/L), amount of micronutrients (0,25 and 0,75 mL/L) (11 and 15 W), and luminosity was used. Fermentation was performed in a 500 mL conical flask with 250 mL of culture medium and 10% inoculum in an incubator with controlled stirring and luminosity. Fermentation was monitored using a spectrophotometer (560 nm), and each fermentation lasted 15 days. Of the parameters studied, luminosity is the one with the highest significance, followed by the amount of nitrogen and the interaction between stirring and micronutrients. Maximum production of biomass for 15 days was 2.70 g/L under the following conditions: luminosity15W; stirring, 120 RPM; source of nitrogen, 1.5 g/L; and micronutrients, 0.75 mL/L.

Forced-air, vacuum, and hydro precooling of cauliflower (Brassica oleracea L. var. botrytis cv. Freemont): part I. determination of precooling parameters

The aim of the present study was to precool cauliflower using forced-air, vacuum and high and low flow hydro cooling methods. The weight of the precooled cauliflower heads (5000±5 g) was measured before they were placed in standard plastic crates. Cauliflower heads, whose initial temperature was 23.5 ± 0.5 ºC, were cooled until the temperature reached at 1 ºC. During the precooling process, time-dependent temperature and energy consumption were measured, and during vacuum precooling, the decreasing pressure values were recorded, and a curve of time-dependent pressure decrease (vacuum) was built. The most suitable cooling method to precool cauliflower in terms of cooling time and energy consumption was vacuum, followed by the high and low flow hydro and forced-air precooling methods, respectively. The highest weight loss was observed in the vacuum precooling method, followed by the forced-air method. However, there was an increase in the weight of the cauliflower heads in the high and low flow hydro precooling method. The best colour and hardness values were found in the vacuum precooling method. Among all methods tested, the most suitable method to precool cauliflower in terms of cooling and quality parameters was the vacuum precooling method.

Effects of gutting process on the shelf life of cultured meagre (Argyrosomus regius ASSO, 1801) stored at 4 ± 1 °C

Abstract The aim of this study was to determine chemical, nutritional and microbiological evaluation of whole or gutted meagre stored at 4 ± 1 oC. Whole ungutted (Group A), eviscerated (Group B), beheaded-eviscerated fish (Group C) and fillets (Group D) groups were created for this study. According to fatty acid analysis, it was determined that meagre is rich in PUFA content and the n3/n6 ratio is within the ideal limits. In all 4 groups, obtained from fillets values were the highest in general, quality parameters were found within acceptable limits. Psychrophilic and mesophilic aerobic bacteria counts exceeded the standards for fillet groups on 7th days of storage. According to microbiological analysis, ungutted, beheaded, eviscerated samples were not exceeded limit values on 9th day. In conclusion, whole or gutted (headed and eviscerated) storage of meagre is found to be more advantageous compared to fillets for storage at 4 ± 1 oC.

Asymmetric Smiles, Leverage Effects and Structural Parameters.

In this paper, we characterize the asymmetries of the smile through multiple leverage effects in a stochastic dynamic asset pricing framework. The dependence between price movements and future volatility is introduced through a set of latent state variables. These latent variables can capture not only the volatility risk and the interest rate risk which potentially affect option prices, but also any kind of correlation risk and jump risk. The standard financial leverage effect is produced by a cross-correlation effect between the state variables which enter into the stochastic volatility process of the stock price and the stock price process itself. However, we provide a more general framework where asymmetric implied volatility curves result from any source of instantaneous correlation between the state variables and either the return on the stock or the stochastic discount factor. In order to draw the shapes of the implied volatility curves generated by a model with latent variables, we specify an equilibrium-based stochastic discount factor with time non-separable preferences. When we calibrate this model to empirically reasonable values of the parameters, we are able to reproduce the various types of implied volatility curves inferred from option market data.

Asymmetric cell division intersects with cell geometry : a method to extrapolate and quantify geometrical parameters of sensory organ precursors

La division cellulaire asymétrique (DCA) consiste en une division pendant laquelle des déterminants cellulaires sont distribués préférentiellement dans une des deux cellules filles. Par l’action de ces déterminants, la DCA générera donc deux cellules filles différentes. Ainsi, la DCA est importante pour générer la diversité cellulaire et pour maintenir l’homéostasie de certaines cellules souches. Pour induire une répartition asymétrique des déterminants cellulaires, le positionnement du fuseau mitotique doit être très bien contrôlé. Fréquemment ceci génère deux cellules filles de tailles différentes, car le fuseau mitotique n’est pas centré pendant la mitose, ce qui induit un positionnement asymétrique du sillon de clivage. Bien qu’un complexe impliquant des GTPases hétérotrimériques et des protéines liant les microtubules au cortex ait été impliqué directement dans le positionnement du fuseau mitotique, le mécanisme exact induisant le positionnement asymétrique du fuseau durant la DCA n'est pas encore compris. Des études récentes suggèrent qu’une régulation asymétrique du cytosquelette d’actine pourrait être responsable de ce positionnement asymétrique du faisceau mitotique. Donc, nous émettons l'hypothèse que des contractions asymétriques d’actine pendant la division cellulaire pourraient déplacer le fuseau mitotique et le sillon de clivage pour créer une asymétrie cellulaire. Nos résultats préliminaires ont démontré que le blebbing cortical, qui est une indication de tension corticale et de contraction, se produit préférentiellement dans la moitié antérieure de cellule précurseur d’organes sensoriels (SOP) pendant le stage de télophase. Nos données soutiennent l'idée que les petites GTPases de la famille Rho pourraient être impliqués dans la régulation du fuseau mitotique et ainsi contrôler la DCA des SOP. Les paramètres expérimentaux développés pour cette thèse, pour étudier la régulation de l’orientation et le positionnement du fuseau mitotique, ouvrirons de nouvelles avenues pour contrôler ce processus, ce qui pourrait être utile pour freiner la progression de cellules cancéreuses. Les résultats préliminaires de ce projet proposeront une manière dont les petites GTPases de la famille Rho peuvent être impliqués dans le contrôle de la division cellulaire asymétrique in vivo dans les SOP. Les modèles théoriques qui sont expliqués dans cette étude pourront servir à améliorer les méthodes quantitatives de biologie cellulaire de la DCA.

A Study on the Transport and Distribution of Atmospheric Aerosols and its Influence on Regional Meteorological Parameters over the Indian Subcontinent

This doctoral thesis addresses the growing concern about the significant changes in the climatic and weather patterns due to the aerosol loading that have taken place in the Indo Gangetic Plain(IGP)which includes most of the Northern Indian region. The study region comprises of major industrial cities in India (New Delhi, Kanpur, Allahabad, Jamshedpur and Kolkata). Northern and central parts of India are one of the most thickly populated areas in the world and have the most intensely farmed areas. Rapid increase in population and urbanization has resulted in an abrupt increase in aerosol concentrations in recent years. The IGP has a major source of coal; therefore most of the industries including numerous thermal power plants that run on coal are located around this region. They inject copious amount of aerosols into the atmosphere. Moreover, the transport of dust aerosols from arid locations is prevalent during the dry months which increase the aerosol loading in theatmosphere. The topography of the place is also ideal for the congregation of aerosols. It is bounded by the Himalayas in the north, Thar Desert in the west, the Vindhyan range in the south and Brahmaputra ridge in the east. During the non‐monsoon months (October to May) the weather in the location is dry with very little rainfall. Surface winds are weak during most of the time in this dry season. The aerosols that reach the location by means of long distance transport and from regional sources get accumulated under these favourable conditions. The increase in aerosol concentration due to the complex combination of aerosol transport and anthropogenic factors mixed with the contribution from the natural sources alters the optical properties and the life time of clouds in the region. The associated perturbations in radiative balance have a significant impact on the meteorological parameters and this in turn determines the precipitation forming process. Therefore, any change in weather which disturbs the normal hydrological pattern is alarming in the socio‐economic point of view. Hence, the main focus of this work is to determine the variation in transport and distribution of aerosols in the region and to understand the interaction of these aerosols with meteorological parameters and cloud properties.

Analysis and Optimization of Machining Process Using Evolutionary Algorithms

To ensure quality of machined products at minimum machining costs and maximum machining effectiveness, it is very important to select optimum parameters when metal cutting machine tools are employed. Traditionally, the experience of the operator plays a major role in the selection of optimum metal cutting conditions. However, attaining optimum values each time by even a skilled operator is difficult. The non-linear nature of the machining process has compelled engineers to search for more effective methods to attain optimization. The design objective preceding most engineering design activities is simply to minimize the cost of production or to maximize the production efficiency. The main aim of research work reported here is to build robust optimization algorithms by exploiting ideas that nature has to offer from its backyard and using it to solve real world optimization problems in manufacturing processes.In this thesis, after conducting an exhaustive literature review, several optimization techniques used in various manufacturing processes have been identified. The selection of optimal cutting parameters, like depth of cut, feed and speed is a very important issue for every machining process. Experiments have been designed using Taguchi technique and dry turning of SS420 has been performed on Kirlosker turn master 35 lathe. Analysis using S/N and ANOVA were performed to find the optimum level and percentage of contribution of each parameter. By using S/N analysis the optimum machining parameters from the experimentation is obtained.Optimization algorithms begin with one or more design solutions supplied by the user and then iteratively check new design solutions, relative search spaces in order to achieve the true optimum solution. A mathematical model has been developed using response surface analysis for surface roughness and the model was validated using published results from literature.Methodologies in optimization such as Simulated annealing (SA), Particle Swarm Optimization (PSO), Conventional Genetic Algorithm (CGA) and Improved Genetic Algorithm (IGA) are applied to optimize machining parameters while dry turning of SS420 material. All the above algorithms were tested for their efficiency, robustness and accuracy and observe how they often outperform conventional optimization method applied to difficult real world problems. The SA, PSO, CGA and IGA codes were developed using MATLAB. For each evolutionary algorithmic method, optimum cutting conditions are provided to achieve better surface finish.The computational results using SA clearly demonstrated that the proposed solution procedure is quite capable in solving such complicated problems effectively and efficiently. Particle Swarm Optimization (PSO) is a relatively recent heuristic search method whose mechanics are inspired by the swarming or collaborative behavior of biological populations. From the results it has been observed that PSO provides better results and also more computationally efficient.Based on the results obtained using CGA and IGA for the optimization of machining process, the proposed IGA provides better results than the conventional GA. The improved genetic algorithm incorporating a stochastic crossover technique and an artificial initial population scheme is developed to provide a faster search mechanism. Finally, a comparison among these algorithms were made for the specific example of dry turning of SS 420 material and arriving at optimum machining parameters of feed, cutting speed, depth of cut and tool nose radius for minimum surface roughness as the criterion. To summarize, the research work fills in conspicuous gaps between research prototypes and industry requirements, by simulating evolutionary procedures seen in nature that optimize its own systems.

Highly conductive and transparent ZnO thin film using Chemical Spray Pyrolysis technique: Effect of doping and deposition parameters

In the present work we report the preparation details studies on ZnO thin films. ZnO thin films are prepared using cost effective deposition technique viz., Chemical Spray Pyrolysis (CSP). The method is very effective for large area preparation of the ZnO thin film. A new post-deposition process could also be developed to avoid the adsorption of oxygen that usually occurs after the spraying process i.e., while cooling. Studies were done by changing the various deposition parameters for optimizing the properties of ZnO thin film. Moreover, different methods of doping using various elements are also tried to enhance the conductivity and transparency of the film to make these suitable for various optoelectronic applications.