A utilização do controle estatístico do processo para o monitoramento do sangue: estudo de caso no Memonorte-RN

The present work is grounded basically on the use of the Basic Tools for the Statistic Process Control SPC, with the intent to detect non-conformities on a given productive process. It consists on a case study accomplished at a Hemocenter in Natal (Rio Grande do Norte). In this study it is shown that, the Statistic Process Control Technique, which was used as a tool, is useful to identify on-conformities on the volume of hemocomponents. The gathering of the used data was performed by means of document analysis, direct observations and database queries. The results achieved from the study show that the analyzed products, even though when they have presented, in some cases, points out of control, they satisfied the ANVISA standards. Finally, suggestions for further improvement of the final product and guidance for future employment of CEP, also extended to other lines of production, are presented

Utilização do controle estatístico do processo para monitoramento do peso médio de cápsulas de Tuberculostáticos: estudo de caso no NUPLAM- RN

This Master Thesis presents a case study on the use of Statistical Process Control (SPC) at the Núcleo de Pesquisas em Alimentos e Medicamentos (NUPLAM). The SPC basic tools have been applied in the process of the tuberculostáticos drugs encapsulation, primarily concerning the objective to choose, between two speeds, which one is the best one to perform the tuberculostatics encapsulation. Later on, with the company effectively operating, the SPC was applied intending to know the variability of the process and, through the tracking of the process itself, to arrive at an estimated limit for the control of future lots of tuberculostatics of equal dosage. As special causes were detected acting in the process, a cause-and-effect diagram was built in order to try to discover, in each factor that composes the productive process, the possible causes of variation of the capsules average weight. The hypotheses raised will be able to serve as a base for deepened the study to eliminate or reduce these interferences in the process. Also a study on the capacity of the process to attend the specifications was carried out, and this study has shown the process´s inaptitude to take care of them. However, on the side of NUPLAM exists a real yearning to implant the SPC and consequently to improve the existing quality already present on its medicines

Importância do gerenciamento com base em dados estudo de caso : farmácias de manipulação do Estado do Rio Grande do Norte

Last century Six Sigma Strategy has been the focus of study for many scientists, between the discoveries we have the importance of data process for the free of error product manufactory. So, this work focuses on data quality importance in an enterprise. For this, a descriptive-exploratory study of seventeen pharmacies of manipulations from Rio Grande do Norte was undertaken with the objective to be able to create a base structure model to classify enterprises according to their data bases. Therefore, statistical methods such as cluster and discriminant analyses were used applied to a questionnaire built for this specific study. Data collection identified four group showing strong and weak characteristics for each group and that are differentiated from each other

Otimização do processo de recuperação do cromo de efluentes de curtumes por microemulsões no extrator Morris

The tanning industries are those which transform animal hide or skin into leather. Due to the complexity of the transformation process, greater quantities of chemicals are being used which results in the generation of effluents with residual solids. The chromium in the residual waters generated by tanning tend to be a serious problem to the environment, therefore the recovery of this metal could result in the reduction of manufacturing costs. This metal is usually found in a trivalent form which can be converted into a hexavalent compound under acidic conditions and in the presence of organic matter. The present study was carried out with the objective to recover chromium through an extraction/re-extraction process using micro emulsions. Micro emulsions are transparent and thermodynamically stable system composed of two immiscible liquids, one forming the continuous phase and the other dispersed into micro bubbles, established by an interfacial membrane formed by surface active and co-surface active molecules. The process of recovering the chromium was carried out in two stages. The first, an extraction process, where the chromium was extracted in the micro emulsion phase and the aqueous phase in excess was separated. In the second stage, a concentrated acid was added to the micro emulsion phase rich in chromium in order to obtain a Winsor II system, where the water that formed in the micro emulsion phase separates into a new micro emulsion phase with a higher concentration of chromium, due to the lowering of the hydrophiles as well as the ionisation of the system. During the experimental procedure, a study was initiated with a synthetic solution of chromium sulphate passing onto the effluent. A Morris extractor was used in the extraction process. Tests were carried out according to the plan and the results were analysed by statistical methods in order to optimise the main parameters that influence the process: the total rate of flow (Q), stirring speed (w) and solvent rate (r). The results, after optimization, demonstrated that the best percentuals in relation to the chromium extraction (99 %) were obtained in the following operational conditions: Q= 2,0 l/h, w= 425 rpm and r= 0,375. The re-extraction was carried out at room temperature (28 °C), 40 °C and 50°C using hydrochloric acid (8 and 10 M) and sulphuric acid (8 M) as re-extracting agents. The results obtained demonstrate that the process was efficient enough in relation to the chromium extraction, reaching to re-extraction percentage higher than 95 %.

Structural Health Monitoring in Smart Structures Through Time Series Analysis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Sorteio de domicílios em favelas em inquéritos por amostragem

OBJETIVO: Identificar vantagens e desvantagens do uso de segmentos em relação ao sorteio feito a partir da lista completa de endereços, para o sorteio de domicílios em amostragem por conglomerados em múltiplos estágios em favelas. PROCEDIMENTOS METODOLÓGICOS: Estudo qualitativo realizado em quatro favelas sorteadas no Inquérito de Saúde do Município de São Paulo, SP, 2008, nas quais foram aplicadas as duas técnicas. Foram realizados grupos focais com pesquisadores de campo - arroladores e entrevistadores do inquérito. Os conteúdos das conversações foram analisados, agrupados em categorias e organizados em núcleos temáticos. ANÁLISE DOS RESULTADOS: A utilização de segmentos de domicílios foi associada a numerosas vantagens e poucas desvantagens. Entre as vantagens, constaram a rapidez e facilidade na elaboração do cadastro de endereços e na localização e identificação de domicílios na etapa de realização das entrevistas, maior segurança dos entrevistadores e da população, maior acesso aos entrevistados, maior estabilidade e maior cobertura do cadastro produzido, e menor ocorrência de erros na identificação dos domicílios sorteados. CONCLUSÕES: A construção de cadastro de domicílios por meio da criação de segmentos é vantajosa em relação à listagem completa de endereços, quando feita em favelas. Por ter se mostrado uma opção econômica e fácil de ser aplicada, constitui alternativa para a simplificação do processo de amostragem em áreas com as suas características de desorganização e adensamento de domicílios.

Short-term induction of thrombocytopenia delays periodontal healing in rats with periodontal disease: participation of endostatin and vascular endothelial growth factor

Background and Objective:Platelets contain factors, including VEGF and endostatin, that can modulate the healing process. We evaluated the effects of severe thrombocytopenia on periodontal healing in rats and determined the contribution of VEGF and endostatin to the healing process.Material and Methods:Rats were distributed into three test groups and two control groups. Cotton ligatures were placed at the gingival margin level of the lower first molar in the test groups. Sham-operated rats and rats in one of the periodontitis groups were killed 15 days later. Rats in the remaining two periodontitis groups had the ligatures removed in order to study the spontaneous recovery from the periodontal disease 15 days later, and these rats were treated with rabbit antiplatelet serum, in order to induce thrombocytopenia, or normal rabbit serum. An additional group without ligatures received antiplatet serum in the same period.Results:After ligature removal, rats treated with normal rabbit serum showed reduced myeloperoxidase activity, decreased alveolar bone loss and increased numbers of blood vessels. Thrombocytopenia caused a delay in alveolar bone regeneration, a decrease in the number of vessels and a modest decrease in myeloperoxidase activity. In the rats with periodontitis, serum endostatin concentrations were slightly decreased and serum VEGF remained unchanged compared with sham-operated animals. After ligature removal, a significant VEGF increase and endostatin decrease were observed in the rats treated with normal rabbit serum. Thrombocytopenia led to a dramatic fall in both VEGF and endostatin concentrations.Conclusion:Thrombocytopenia leads to a delay of periodontal healing in the situation of experimental periodontitis, which might be mediated in part by a decrease in the serum concentration of VEGF and endostatin derived from the platelets. However, other factors derived from the platelets may also have contributed to a delay of periodontal healing in the rats with thrombocytopenia.

The use of artificial neural networks in analysing the nutritional ecology of Chrysomya megacephala (F.) (Diptera: Calliphoridae), compared with a statistical model

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The CMS experiment at the CERN LHC

The Compact Muon Solenoid (CMS) detector is described. The detector operates at the Large Hadron Collider (LHC) at CERN. It was conceived to study proton-proton (and lead-lead) collisions at a centre-of-mass energy of 14 TeV (5.5 TeV nucleon-nucleon) and at luminosities up to 10(34)cm(-2)s(-1) (10(27)cm(-2)s(-1)). At the core of the CMS detector sits a high-magnetic-field and large-bore superconducting solenoid surrounding an all-silicon pixel and strip tracker, a lead-tungstate scintillating-crystals electromagnetic calorimeter, and a brass-scintillator sampling hadron calorimeter. The iron yoke of the flux-return is instrumented with four stations of muon detectors covering most of the 4 pi solid angle. Forward sampling calorimeters extend the pseudo-rapidity coverage to high values (vertical bar eta vertical bar <= 5) assuring very good hermeticity. The overall dimensions of the CMS detector are a length of 21.6 m, a diameter of 14.6 m and a total weight of 12500 t.

Optimal and sub-optimal control in Dengue epidemics

This work concerns the application of the optimal control theory to Dengue epidemics. The dynamics of this insect-borne disease is modelled as a set of non-linear ordinary differential equations including the effect of educational campaigns organized to motivate the population to break the reproduction cycle of the mosquitoes by avoiding the accumulation of still water in open-air recipients. The cost functional is such that it reflects a compromise between actual financial spending (in insecticides and educational campaigns) and the population health (which can be objectively measured in terms of, for instance, treatment costs and loss of productivity). The optimal control problem is solved numerically using a multiple shooting method. However, the optimal control policy is difficult to implement by the health authorities because it is not practical to adjust the investment rate continuously in time. Therefore, a suboptimal control policy is computed assuming, as the admissible set, only those controls which are piecewise constant. The performance achieved by the optimal control and the sub-optimal control policies are compared with the cases of control using only insecticides when Breteau Index is greater or equal to 5 and the case of no-control. The results show that the sub-optimal policy yields a substantial reduction in the cost, in terms of the proposed functional, and is only slightly inferior to the optimal control policy. Copyright (C) 2001 John Wiley & Sons, Ltd.

Qualidade da colheita mecanizada de feijão (Phaseolus vulgaris) em dois sistemas de preparo do solo

Dentre as etapas de produção do feijoeiro a colheita é uma das mais importantes, porque pode interferir de maneira decisiva na qualidade e no custo de produção. Assim, objetivou-se avaliar a qualidade da operação da colheita mecanizada de feijão (Phaseolus vulgaris), cultivado sob preparo convencional e plantio direto. As variáveis analisadas foram: o nível de ruído emitido, calculado através de um medidor de pressão sonora; o desempenho operacional, sendo monitorado o consumo de combustível, a patinagem dos rodados e a velocidade de deslocamento do conjunto coletados em uma central digital (datalogger); e a operação de colheita quanto à matéria seca e densidade de palhada, e as perdas na colheita. A velocidade e os consumos horário e operacional apresentaram distribuição normal dos dados, enquanto que o nível de ruído apresentou distribuição assimétrica. As perdas na colheita mecanizada de feijão e a densidade de palhada apresentaram baixa variabilidade e distribuição normal. Assim, apenas o consumo horário e a produção de matéria seca de palhada apresentaram comportamento instável em relação ao controle estatístico de processo, enquanto os demais indicadores mostraram condições de manter a qualidade da operação de colheita tanto no preparo convencional de solo quanto no plantio direto.

Controle estatístico aplicado ao processo de colheita mecanizada de cana-de-açúcar

O avanço da mecanização na colheita da cana-de-açúcar (Saccharum spp.) proporcionou o uso de novas tecnologias e ganho em produtividade para a cultura. O controle da qualidade do processo de colheita da cana-de-açúcar é fundamental para reduzir as perdas. Este trabalho teve o objetivo de avaliar as perdas na colheita mecanizada de cana-de-açúcar, utilizando-as como indicadores de qualidade do processo de colheita. Os dados foram coletados em duas propriedades próximas a Jaboticabal - SP, com a variedade SP80-3280, em 3º e 4º cortes. Caracterizou-se o porte do canavial e, após a colheita, demarcou-se área de 1,5 ha, sendo demarcados 25 pontos, espaçados de 12 x 50 m, quantificando-se as perdas visíveis. Posteriormente, foi aplicado o controle estatístico do processo pela média, que consta de três vezes o desvio-padrão para mais ou para menos, sendo esses os limites superior e inferior de controle, respectivamente. A média das perdas de pedaço solto foi estatisticamente maior do que as médias de perdas em pedaço fixo, cana inteira, cana-ponta e toco. A ocorrência de perdas em rebolo estilhaçado foi menor para o 4º corte em relação ao 3º corte, enquanto as perdas em pedaço fixo e toco foram menores no 3º corte, comparadas às perdas no 4º corte. em cada corte, as médias para as perdas totais estiveram próximas dos valores encontrados na bibliografia. Pedaço solto foi a variável de perdas visíveis com maior percentagem de ocorrência. As perdas demonstraram que a colheita mecanizada não se encontra sob controle estatístico de processo.

Caracterização das perdas e distribuição de cobertura vegetal em colheita mecanizada de soja

O conceito de controle de qualidade nas operações inserido na agricultura é viabilizado por incidir diretamente nos principais objetivos do processo produtivo: retorno econômico e aumento da produtividade. A colheita mecanizada normalmente é realizada sem que haja controle efetivo para que a variabilidade das perdas fique dentro de padrões aceitáveis. Esta pesquisa teve o objetivo de determinar e caracterizar as perdas e a distribuição da cobertura vegetal após a colheita mecanizada da soja, por meio de ferramenta de controle estatístico de processo (cartas de controle). A média da perda de grãos total foi próxima do limite superior aceitável para a cultura da soja, apresentando alta variabilidade entre os pontos, tornando o processo fora de controle. A distribuição de cobertura vegetal manteve-se em processo controlado, com maior variabilidade onde o relevo foi mais inclinado. A utilização das cartas de controle foi eficiente na identificação dos pontos fora de controle e na avaliação da qualidade do processo de colheita.

Gráficos adaptativos de controle por atributos e seu projeto na prática

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Planejamento do controle estatístico de processos com baixa fração não conforme restrito a amostras pequenas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)