Comparative degradation of ZnO- and SnO(2)-based polycrystalline non-ohmic devices by current pulse stress

The degradation behaviour of SnO(2)-based varistors (SCNCr) due to current pulses (8/20 mu s) is reported here for the first time in comparison with the ZnO-based commercial varistors (ZnO). Puncturing and/or cracking failures were observed in ZnO-based varistors possessing inferior thermo-mechanical properties in comparison with that found in a SCNCr system free of failures. Both systems presented electric degradation related to the increase in the leakage current and decrease in the electric breakdown field, non-linear coefficient and average value of the potential barrier height. However, it was found that a more severe degradation occurred in the ZnO-based varistors concerning their non-ohmic behaviour, while in the SCNCr system, a strong non-ohmic behaviour remained after the degradation. These results indicate that the degradation in the metal oxide varistors is controlled by a defect diffusion process whose rate depends on the mobility, the concentration of meta-stable defects and the amount of electrically active interfaces. The improved behaviour of the SCNCr system is then inferred to be associated with the higher amount of electrically active interfaces (85%) and to a higher energy necessary to activate the diffusion of the specific defects.

Color tunability of intense upconversion emission from Er3+-Yb3+ co-doped SiO2-Ta2O5 glass ceramic planar waveguides

This work reports on the infrared-to-visible CW frequency upconversion from planar waveguides based on Er3+-Yb3+-doped 100-xSiO(2)-xTa(2)O(5) obtained by a sol-gel process and deposited onto a SiO2-Si substrate by dip-coating. Surface morphology and optical parameters of the planar waveguides were analyzed by atomic force microscopy and the m-line technique. The influence of the composition on the electronic properties of the glass-ceramic films was followed by the band gap ranging from 4.35 to 4.51 eV upon modification of the Ta2O5 content. Intense green and red emissions were detected from the upconversion process for all the samples after excitation at 980 nm. The relative intensities of the emission bands around 550 nm and 665 nm, assigned to the H-2(11/2) -> I-4(15/2), S-4(3/2) -> I-4(15/2), and F-4(9/2) -> I-4(15/2) transitions, depended on the tantalum oxide content and the power of the laser source at 980 nm. The upconversion dynamics were investigated as a function of the Ta2O5 content and the number of photons involved in each emission process. Based on the upconversion emission spectra and 1931CIE chromaticity diagram, it is shown that color can be tailored by composition and pump power. The glass ceramic films are attractive materials for application in upconversion lasers and near infrared-to-visible upconverters in solar cells.

PbO-GeO2 rare earth doped glasses with silver nanoparticles as materials for IR laser triggers

We have shown the possibility of operation by the piezooptical response of PbO-GeO2 glasses doped with rare earth ions and silver nanoparticles by illumination of double frequency CO2 nanosecond laser. Substantial influence of thermoannealing on the output photoinduced elastooptical susceptibilities was established. The effect is very sensitive to temperature and to the corresponding tensor components. The effect of thermoannealing leads to enhanced long-range ordering with the occurrence of corresponding trapping levels within the forbidden gaps. The discovered effects may be used for creation of low-temperature IR laser triggers.

Frequency upconversion properties of Tm3+ doped TeO2-ZnO glasses containing silver nanoparticles

Frequency upconversion (UC) properties of Tm3+ doped TeO2-ZnO glasses containing silver nanoparticles (NPs) were investigated. Infrared-to-visible and infrared-to-infrared UC processes associated to the Tm3+ ions were studied by exciting the samples with a cw 1050 nm ytterbium laser. The luminescence intensity as a function of laser intensity was also measured using a pulsed 1047 nm Nd3+:YVO laser in order to determine the number of photons participating in the UC processes. Enhancement of the UC signals for samples heat-treated during various time intervals is attributed to the growth of the local field in the vicinity of the NPs. PL enhancement by one-order of magnitude was observed in the whole spectrum of the samples heat-treated during 48 h. On the other hand PL quenching was observed for the samples heat-treated more than 48 h. (c) 2011 Elsevier B.V. All rights reserved.

NIR luminescent Er3+/Yb3+ co-doped SiO2-ZrO2 nanostructured planar and channel waveguides: Optical and structural properties

Optical and structural properties of planar and channel waveguides based on sol gel Er3+ and Yb3+ co-doped SiO2-ZrO2 are reported. Microstructured channels with high homogeneous surface profile were written onto the surface of multilayered densified films deposited on SiO2/Si substrates by a femtosecond laser etching technique. The densification of the planar waveguides was evaluated from changes in the refractive index and thickness, with full densification being achieved at 900 degrees C after annealing from 23 up to 500 min, depending on the ZrO2 content Crystal nucleation and growth took place together with densification, thereby producing transparent glass ceramic planar waveguides containing rare earth-doped ZrO2 nanocrystals dispersed in a silica-based glassy host Low roughness and crack-free surface as well as high confinement coefficient were achieved for all the compositions. Enhanced NIR luminescence of the Er3+ ions was observed for the Yb3+- codoped planar waveguides, denoting an efficient energy transfer from the Yb3+ to the Er3+ ion. (C) 2012 Elsevier B.V. All rights reserved.

Optical and thermal investigation of GeO2-PbO thin films doped with Au and Ag nanoparticles

The present work reports on the thermo-optical study of germanate thin films doped with Au and Ag nanoparticles. Transmission Electron Microscopy images, UV-visible absorption and Micro-Raman scattering evidenced the presence of nanoparticles and the formation of collective excitations, the so called surface plasmons. Moreover, the effects of the metallic nanoparticles in the thermal properties of the films were observed. The thermal lens technique was proposed to evaluate the Thermal Diffusivity (D) of the samples. It furnishes superficial spatial resolution of about 100 mu m, so it is appropriate to study inhomogeneous samples. It is shown that D may change up to a factor 3 over the surface of a film because of the differences in the nanoparticles concentration distribution. (C) 2011 Elsevier B.V. All rights reserved.

Evaluation of the micro-hardness and fracture toughness of amorphous and partially crystallized 3CaO center dot P2O5-SiO2-MgO bioglasses

In this work, the effect of the indentation load on the results of hardness and fracture toughness, determined by Vickers micro-hardness measurements, of some glasses and glass-ceramics has been investigated. Furthermore, in order to verify the effect of crystallinity on the results, glasses of composition 52.75 wt.% 3CaO center dot P2O5, 30 wt.% SiO2 and 17.25 wt.% MgO were fused at 1600 degrees C for 4 h and annealed at 700 degrees C for 2h, and further heat-treated at 700, 775, 800 and 900 degrees C for 4h. The obtained materials were analyzed by high resolution X-ray diffraction, HRXRD, to determine the crystallization degree in function of the heat-treatment temperature. The hardness of the different specimens was determined by Vickers' micro-hardness measurements under various loads. It has been observed that with increasing crystallization of the materials their hardness increased. Furthermore, it has been possible to verify the so-called indentation size effect (ISE), i.e. hardness decreases as the indentation depth, under higher loads, increases. This effect has been more pronounced in the glass-ceramic samples. Fracture toughness has been determined by the crack length induced by the Vickers indentations and relating them to the applied loads. Glass materials presented a fracture pattern with characteristics of cleavage, forming cracks of the half-penny shaped type, while the glass-ceramic materials exhibited crack bridging effects and Palmqvist type cracks. (C) 2011 Elsevier B.V. All rights reserved.

Tuning Low-Spin to High-Spin Mn Pairs in 2-D ZnO by Injecting Holes

We have performed an ab initio theoretical investigation of substitutional Mn(Zn) atoms in planar structures of ZnO, viz., monolayer [(ZnO)(1)] and bilayer [(ZnO)(2)] systems. Due to the 2-D quantum confinement effects, in those Mn -doped (ZnO)(1) and (ZnO)(2) structures, the antiferromagnetic (AFM) coupling between (nearest neighbor) Mn(Zn) impurities have been strengthened when compared with the one in ZnO bulk systems. On the other hand, we find that the magnetic state of these systems can be tuned from AFM to FM by adding holes, which can be supplied by a p-type doping or even photoionization processes. Whereas, upon addition of electrons (n-type doping), the system keeps its AFM configuration.

The influence of SiO2 content on spectroscopic properties and laser emission efficiency of Yb3+-Er3+ co-doped calcium aluminosilicate glasses

We have studied the influence of SiO2 content on the spectroscopic properties and laser emission efficiency of Yb3+-Er3+ co-doped calcium aluminosilicate glasses. An increase in SiO2 content resulted in higher phonon energy, which reduced the up-conversion emission, enhanced the energy transfer efficiency up to 70 % from Yb3+ to Er3+, and enhanced the optical quality. All these results led to an increase from 20 to 30 % in the laser emission efficiency.

Microwave Hydrothermal Synthesis and Photocatalytic Performance of ZnO and M:ZnO Nanostructures (M = V, Fe, Co)

ZnO and doped M:ZnO (M = V, Fe and Co) nanostructures were synthesized by microwave hydrothermal synthesis using a low temperature route without addition of any surfactant. The transition metal ions were successfully doped in small amount (3% mol) into ZnO structure. Analysis by X-ray diffraction reveals the formation of ZnO with the hexagonal (wurtzite-type) crystal structure for all the samples. The as-obtained samples showed a similar flower-like morphology except for Fe:ZnO samples, which presented a plate-like morphology. The photocatalytic performance for Rhodamine B (RhB) degradation confirmed that the photoactivity of M:ZnO nanostructures decreased for all dopants in structure, according to their eletronegativity. Photoluminescence spectroscopy was employed to correlate M:ZnO structure with its photocatalytical properties. It was suggested that transition metal ions in ZnO lattice introduce defects that act as trapping or recombination centers for photogenerated electrons and holes, making it impossible for them reach the surface and promote the photocatalytical process.

The Banhado Alkaline Complex, Southeastern Brazil: source and evolution of potassic SiO2-undersaturated high-Ca and low-Ca magmatic series

The Cretaceous Banhado alkaline complex in southeastern Brazil presents two potassic SiO2-undersaturated series. The high-Ca magmatic series consist of initially fractionated olivine (Fo(92-91)) + diopside (Wo(48-43)En(49-35)Ae(0-7)), as evidenced by the presence of xenocrysts and xenoliths. In that sequence, diopside (Wo(47-38)En(46-37)Ae(0-8)) + phlogopite + apatite + perovskite (Prv(> 92)) crystallized to form the phlogopite melteigite and led to the Ca enrichment of the magma. Diopside (Wo(47-41)En(32-24) Ae(3-14)) continued to crystallize as an early mafic mineral, followed by nepheline (Ne(74.8-70.1)Ks(26.3-21.2)Qz(7.6-0.9)) and leucite (Lc(65-56)) and subsequently by melanite and potassic feldspar (Or(85-99)Ab(1-7)) to form melanite ijolites, wollastonite-melanite urtites and melanite-nepheline syenites. Melanite-pseudoleucite-nepheline syenites are interpreted to be a leucite accumulation. Melanite nephelinite dykes are believed to represent some of the magmatic differentiation steps. The low-Ca magmatic series is representative of a typical fractionation of aegirine-augite (Wo(36-29)En(25-4)Ae(39-18)) + alkali feldspar (Or(57-96)Ab(3-43)) + nepheline (Ne(76.5-69.0)Ks(19.9-14.4)Qz(15.1-7.7)) + titanite from phonolite magma. The evolution of this series from potassic nepheline syenites to sodic sodalite syenites and sodalitolites is attributed to an extensive fractionation of potassic feldspar, which led to an increase of the NaCl activity in the melt during the final stages forming sodalite-rich rocks. Phonolite dykes followed a similar evolutionary process and also registered some crustal assimilation. The mesocratic nepheline syenites showed interactions with phlogopite melteigites, such as compatible trace element enrichments and the presence of diopside xenocrysts, which were interpreted to be due to a mixing/mingling process of phonolite and nephelinite magmas. The geochemical data show higher TiO2 and P2O5 contents and lower SiO2 contents for the high-Ca series and different LILE evolution trends and REE chondrite-normalized patterns as compared to the low-Ca series. The Sr-87/Sr-86, Nd-143/Nd-144, Pb-206/Pb-204 and Pb-208/Pb-204 initial ratios for the high-Ca series (0.70407-0.70526, 0.51242-0.51251, 17.782-19.266 and 38.051-39.521, respectively) were slightly different from those of the low-Ca series (0.70542-0.70583, 0.51232-0.51240, 17.758-17.772 and 38.021-38.061, respectively). For both series, a CO2-rich potassic metasomatized lithospheric mantle enriched the source with rutile-bearing phlogopite clinopyroxenite veins. Kamafugite-like parental magma is attributed to the high-Ca series with major contributions from the melting of the veins. Potassic nephelinite-like parental magma is assigned to the low-Ca series, where the metasomatized wall-rock played a more significant role in the melting process.

Avaliação do molhamento da matriz de um concreto refratário (Al2O3-SiC-SiO2-C) por escórias sintéticas contendo distintos teores de MgO

O comportamento de espalhamento de quatro escórias sintéticas foi investigado pelo método da gota séssil, quando em contato com a matriz de um concreto refratário contendo alto teor de carbono e carbeto de boro como agente antioxidante. A evolução do molhamento do sólido foi monitorada a 1450, 1550 e 1650 ºC por 1800 s. Além disso, simulações termodinâmicas foram efetuadas, usando o programa FactSage®, visando promover um maior entendimento das reações químicas que podem ocorrer na interface dos materiais avaliados. Foi observado que a composição química do líquido afetou diretamente o espalhamento deste e quanto maior o teor de MgO na composição da escória, maiores foram os valores do ângulo de contato entre líquido e sólido. No entanto, em altas temperaturas e tempos prolongados, foram verificadas a formação de bolhas na superfície do líquido e a infiltração das escórias nos poros do refratário. Estes fatores afetaram negativamente e tornaram menos conclusivos os dados coletados nos ensaios propostos, apontando que ainda são necessários aperfeiçoamentos da técnica de molhabilidade para a avaliação de materiais complexos, tais como os concretos refratários.

Cobalt dotiertes ZnO als verdünnter magnetischer Halbleiter

Verdünnte magnetische Halbleiter (DMS) sind technologisch vielversprechende Materialien mit sowohl ferromagnetischen als auch halbleitenden Eigenschaften. Sie gehören zu den entscheidenden Verbindungen bei der Entwicklung neuartiger Spintronikanwendungen. Bisher scheiterte der technologische Einsatz jedoch daran, dass die Curie Temperatur der meisten magnetischen Halbleiter viel zu niedrig ist. Neue Verbindungen auf Basis von ZnO wie Zn1-xCoxO sollen jedoch Ferromagnetismus oberhalb von Raumtemperatur zeigen. Die theoretischen Grundlagen der magnetischen Wechselwirkungen sind jedoch nicht verstanden und erfordern daher umfangreiche experimentelle Untersuchungen. Im Rahmen dieser Arbeit wurden dünne Filme aus Zn0.95Co0.05O mittels Laserablation hergestellt und bezüglich ihrer magnetischen, elektrischen und strukturellen Eigenschaften untersucht, mit dem Ziel den Ferromagnetismus in diesem Material besser zu verstehen. Dabei kamen verschiedene experimentelle Methoden zum Einsatz: wie Magnetometrie, Röntgendiffraktometrie, Magnetischer Röntgenzirkulardichroismus (XMCD), Elektronenspinresonanz sowie magnetoelektrische Transportmessungen. Bei entsprechend defektfördernden Herstellungsbedingungen zeigen die Proben klare ferromagnetische Eigenschaften oberhalb von Raumtemperatur mit einer Sättigungsmagnetisierung von ca. 2 Bohr Magneton / Co sowie einer Remanenz von bis zu 90%. Elektrische Transportmessungen zeigen zudem einen deutlichen Magnetowiderstand sowie einen anomalen Hall Effekt. Letzterer steigt mit der Probenmagnetisierung und spricht für intrinsischen Ferromagnetismus sowie eine geringe Spinpolarisation. Da der Ferromagnetismus mit höherer Ladungsträgerdichte jedoch verschwindet, ist eine ferromagnetische Wechselwirkung über die Leitungselektronen auszuschließen. Eine genauere Auswertung der magnetoelektrischen Messdaten deutet zudem auf ein leitendes Störstellenband hin, das unter Umständen selbst spinpolarisiert ist. Vieles spricht somit dafür, dass die ferromagnetische Ordnung über magnetische Polaronen zustande kommt. Einige strukturelle und magnetometrische Ergebnisse sowie Elektronenspinresonanzmessungen deuten zudem auf metallische Ausscheidungen in Form von Cobalt Clustern hin, die einen zusätzlichen extrinsischen ferromagnetischen Beitrag liefern, der deutlich größer sein könnte als der intrinsische. Überraschenderweise zeigen XMCD Messungen jedoch, dass Cobalt überhaupt nicht am Ferromagnetismus beteiligt ist. Insgesamt gibt es Anzeichen, dass magnetische Defekte eine entscheidende Rolle hinsichtlich des Magnetismus in Zn0.95Co0.05O spielen.

Kontrolle der Grenzflächeneigenschaften anorganischer Nanopartikel mittels amphiphiler Polymere

Im Rahmen dieser Arbeit wurden amphiphile Co- und Terpolymere verwendet, um die Grenzflächeneigenschaften anorganischer Nanopartikel zu kontrollieren. Es wurde eine effiziente und vielseitige Methode entwickelt, mit der in-situ hydrophobierte, formanisotrope ZnO-, CdS- und Au-Nanopartikel sowie poröse TiO2-Nanopartikel hergestellt werden konnten. Diese Technik basierte auf der Fällung anorganischer Nanopartikel in einer inversen Emulsion mittels kombinierten Einsatzes zweier maßgeschneiderter amphiphiler Polymere. Ein Copolymer ermöglichte sowohl die Stabilisierung der Emulsion als auch die Hydrophobierung der Partikel, und ein weiteres Struktur-dirigierendes Agens (SDA) kontrollierte den Kristallisationsprozess. Infolge ihrer Form zeigten die Nanopartikel von sphärischen Teilchen abweichende Lagen der Oberflächenplasmonenresonanz und der Bandlücke. Aufgrund der hervorragenden Hydrophobierung dieser Kolloide mittels amphiphiler Copolymere konnten diese homogen in polymere Materialien eingearbeitet werden. Dies erlaubte es die speziellen Eigenschaften von nicht-sphärischen Kolloiden auf Nanokompositmaterialien zu übertragen. Darüber hinaus wurden amphipolare Copolymere genutzt, um superhydrophobe Oberflächen zu generieren. Hierzu wurden Filme bestehend aus rauen SiO2-Nanopartikeln mit fluorierten Emulgatoren beschichtet. In einem dritten Schwerpunkt dieser Arbeit wurden amphiphile Co- und Terpolymere verwendet, um anorganische Nanopartikel zu hydrophilieren. Durch Variation der Emulgatorzusammensetzung konnten die Ladung und Ladungsdichte auf der Partikeloberfläche gezielt gesteuert werden. Darüber hinaus konnte die Partikelhülle zusätzlich mit Farbstoffmolekülen funktionalisiert werden, was den erfolgreichen Einsatz der Kolloide in Zellaufnahmeexperimenten ermöglichte.

Kolloide und ihre Überstrukturen als Bausteine zur Herstellung funktioneller Materialien

In dieser Arbeit wird die Synthese von Polymerkolloiden mit unterschiedlichen Formen und Funktionalitäten sowie deren Verwendung zur Herstellung kolloidaler Überstrukturen beschrieben. Über emulgatorfreie Emulsionspolymerisation (SFEP) erzeugte monodisperse sphärische Kolloide dienen als Bausteine von Polymeropalen, die durch die Selbstorganisation dieser Kolloide über vertikale Kristallisation (mit Hilfe einer Ziehmaschine) oder horizontale Kristallisation (durch Aufschleudern oder Aufpipettieren) entstehen. Durch die Kontrolle der Kugelgröße über die Parameter der Emulsionspolymerisation sowie die Einstellung der Schichtdicke der Kolloidkristalle über die Anpassung der Kristallisationsparameter ist die Erzeugung von qualitativ hochwertigen Opalen mit definierter Reflektionswellenlänge möglich. Darüber hinaus kann die chemische und thermische Beständigkeit der Opale durch den Einbau von Vernetzern oder vernetzbaren Gruppen in die Polymere erhöht werden. Die Opalfilme können als wellenlängenselektive Reflektoren in auf Fluoreszenzkonzentratoren basierenden Solarzellensystemen eingesetzt werden, um Lichtverluste in diesen Systemen zu reduzieren. Sie können auch als Template für die Herstellung invertierter Opale aus verschiedenen anorganischen Oxiden (TiO2, Al2O3, ZnO) dienen. Über einen CVD-Prozess erzeugte ZnO-Replika besitzen dabei den Vorteil, dass sie nicht nur eine hohe optische Qualität sondern auch eine elektrische Leitfähigkeit aufweisen. Dies ermöglicht sowohl deren Einsatz als Zwischenreflektor in Tandemsolarzellen als auch die Herstellung hierarchischer Strukturen über die Elektroabscheidung von Nanokristallen. In einem weiteren Teil der Arbeit wird die Herstellung funktioneller formanisotroper Partikel behandelt. Durch die Entmischung von mit Monomer gequollenen vernetzten Partikeln in einer Saatpolymerisation sind mehrere Mikrometer große Kolloide zugänglich, die aus zwei interpenetrierenden Halbkugeln aus gleichen oder verschiedenen Polymeren bestehen. Dadurch sind unter anderem Glycidyl-, Alkin- und Carbonsäuregruppen in die eine oder die andere Halbkugel integrierbar. Diese funktionellen Gruppen erlauben die Markierung bestimmter Partikelhälften mit Farbstoffen, die Beschichtung von Partikelbereichen mit anorganischen Oxiden wie SiO2 sowie die Erzeugung amphiphiler formanisotroper Partikel, die sich an Grenzflächen ausrichten lassen. Das Synthesekonzept kann - ausgehend von mittels SFEP erzeugten stark vernetzten PMMA-Partikeln - auch auf kleine Kolloide mit Größen von mehreren hundert Nanometern übertragen werden.