Comparação dos efeitos de compressão isostática e compressão uniaxial na obtenção da liga NiTi por metalurgia do pó

Several alloys present the shape memory effect and among them, the equiatomic NiTi alloy, nitinol, is the most important one. It is usually used in several engineering applications and also in biomedical devices, in the fabrication of orthodontic wire, stents and Judet staples. Although a considerable amount of these biomedical devices is utilized in Brazil and a fraction of it is already made here, all nitinol used is bought abroad. Thus, it is important to develop the necessary know-how to fabricate NiTi wire and sheet. It would mean less importation with job creation and wealth generation for the country. In this work nitinol was obtained powder metallurgy from elemental powders of Ti and Ni using uniaxial compression and uniaxial compression followed by isostatic compression. The final densities achieved were determined by the Archimedes method. The precipitation of intermetallic secondary phases was studied and the samples were characterized by metallographic analysis, optical microscopy and X-ray diffraction. Results indicated that 50 hours sintering route showed a low amount of intermetallics, and no trace of unreacted powder. XRD and metallography at room temperature indicated B19’ as the predominant phase, which corresponds to martensite. Although density results showed little dispersion, the most dense sample was compacted under uniaxial compression and presented 4.8 g/cm3, corresponding to 20.84% porosity. Density variation was considered normal to the measurement process and independent of the compaction mode

Técnicas de caracterização microestrutural, por microscopia óptica e microscopia eletrônica de varredura, de aços bifásicos e multifásicos aplicados à indústria automobilística

This project developed microstructural characterization technics of commercial dualphase and multi-phasic (TRIP) steels that were provided by the automotive industry and are currently used as the raw material for the production of automobiles. Inserted in this context, there is the development of the advanced high strength steels in consonance with the ULSABAVC project, which aims the production of safe, economically viable and efficient in terms of fuel consumption vehicles for the 21st century. The micro-structural characterization of biphasic and multiphase steels was done by the identification and quantification of the coexistent phases. In this item, a special attention was given to the technics that were performed using optic microscopy and scanning electron microscopy. An important contribution to this work was the utilization of different alternative chemical reagents (Beraha, Heat-Tinting technics) in addition to the classical ones (Nital and LePera)already used conventionally by the UNESP's Group of Mechanical, Microstructural and Fractografic Characterization of Materials. The revealed microstructures were correlated with the materials' mechanical properties determined through traction tests, such as ultimate tensile strengths, yield strength and stretching important since the material has structural application in the automotive industry. As a result, it was observed the superiority concerning the studied mechanical properties for the biphasic and multiphasic steels when compared to the conventional carbon steels. Besides, it was perceived a large potential for the industrial scale utilization of the Heat Tinting technics in this field, seen its differentiation of the existent phases and easy reproducibility

Avaliação do processo de contaminação e remediação de água subterrânea por hidrocarbonetos

Pós-graduação em Engenharia Civil e Ambiental - FEB

O efeito da ordenação e estrutura geométrica dos materiais PtSn/C e PdSn/C na eletrooxidação do glicerol em meio alcalino

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo da influência do tratamento térmico a laser nas características dos aços avançados de alta resistência dual phase 600 e transformed induced plasticity 750

Pós-graduação em Engenharia Mecânica - FEG

Análise microestrutural e caracterização mecânica do aço AISI 4350 submetido a diferentes tratamentos térmicos

The multiphase steels are gaining increasing attention in scientific studies because of the different mechanical and microstructural properties that the material can achieve under different thermomechanical and heat treatments that can be submitted. In the present study, it was made a microstructural study thru the triple attack technic associated with optical microscopy and mechanical characterization of medium carbon AISI 4350 steel thru a tensile strength test, subjected to three routes of heat treatment: annealing, quenching and tempering and isothermal annealing. It was verified the predominance of ferrite-perlite constituent in the specimen annealed, martensitic in the quenched and tempered specimen and bainitic in the annealed isothermally specimen. The annealed material showed a higher ductility, while the hardened and tempered specimen showed the highest hardness and ultimately the bainitic specimen showed a combination of the two abovementioned mechanical properties. Thus, we proved that the multiphase steel SAE 4350 can be a versatile material with great potential for various industrial applications

Análise microestrutural e caracterização mecânica do aço AISI 4350 submetido a diferentes tratamentos térmicos

The multiphase steels are gaining increasing attention in scientific studies because of the different mechanical and microstructural properties that the material can achieve under different thermomechanical and heat treatments that can be submitted. In the present study, it was made a microstructural study thru the triple attack technic associated with optical microscopy and mechanical characterization of medium carbon AISI 4350 steel thru a tensile strength test, subjected to three routes of heat treatment: annealing, quenching and tempering and isothermal annealing. It was verified the predominance of ferrite-perlite constituent in the specimen annealed, martensitic in the quenched and tempered specimen and bainitic in the annealed isothermally specimen. The annealed material showed a higher ductility, while the hardened and tempered specimen showed the highest hardness and ultimately the bainitic specimen showed a combination of the two abovementioned mechanical properties. Thus, we proved that the multiphase steel SAE 4350 can be a versatile material with great potential for various industrial applications

Directed and elliptic flow of charged particles in Cu plus Cu collisions at root s(NN)=22.4 GeV

This paper reports results for directed flow v(1) and elliptic flow v(2) of charged particles in Cu + Cu collisions at root s(NN) = 22.4 GeV at the Relativistic Heavy Ion Collider. The measurements are for the 0-60% most central collisions, using charged particles observed in the STAR detector. Our measurements extend to 22.4-GeV Cu + Cu collisions the prior observation that v1 is independent of the system size at 62.4 and 200 GeV and also extend the scaling of v(1) with eta/y(beam) to this system. The measured v(2)(p(T)) in Cu + Cu collisions is similar for root s(NN) throughout the range 22.4 to 200 GeV. We also report a comparison with results from transport model (ultrarelativistic quantum molecular dynamics and multiphase transport model) calculations. The model results do not agree quantitatively with the measured v(1)(eta), v(2)(p(T)), and v(2)(eta).

Analysis of energy dissipation in stirred suspension polymerisation reactors using computational fluid dynamics

This work evaluates the spatial distribution of normalised rates of droplet breakage and droplet coalescence in liquidliquid dispersions maintained in agitated tanks at operation conditions normally used to perform suspension polymerisation reactions. Particularly, simulations are performed with multiphase computational fluid dynamics (CFD) models to represent the flow field in liquidliquid styrene suspension polymerisation reactors for the first time. CFD tools are used first to compute the spatial distribution of the turbulent energy dissipation rates (e) inside the reaction vessel; afterwards, normalised rates of droplet breakage and particle coalescence are computed as functions of e. Surprisingly, multiphase simulations showed that the rates of energy dissipation can be very high near the free vortex surfaces, which has been completely neglected in previous works. The obtained results indicate the existence of extremely large energy dissipation gradients inside the vessel, so that particle breakage occurs primarily in very small regions that surround the impeller and the free vortex surface, while particle coalescence takes place in the liquid bulk. As a consequence, particle breakage should be regarded as an independent source term or a boundary phenomenon. Based on the obtained results, it can be very difficult to justify the use of isotropic assumptions to formulate particle population balances in similar systems, even when multiple compartment models are used to describe the fluid dynamic behaviour of the agitated vessel. (C) 2011 Canadian Society for Chemical Engineering

Biogenic Potassium Salt Particles as Seeds for Secondary Organic Aerosol in the Amazon

The fine particles serving as cloud condensation nuclei in pristine Amazonian rainforest air consist mostly of secondary organic aerosol. Their origin is enigmatic, however, because new particle formation in the atmosphere is not observed. Here, we show that the growth of organic aerosol particles can be initiated by potassium-salt-rich particles emitted by biota in the rainforest. These particles act as seeds for the condensation of low- or semi-volatile organic compounds from the atmospheric gas phase or multiphase oxidation of isoprene and terpenes. Our findings suggest that the primary emission of biogenic salt particles directly influences the number concentration of cloud condensation nuclei and affects the microphysics of cloud formation and precipitation over the rainforest.

Reddenings of Cepheids

The aim of this work is to derive precise reddenings for 31 Cepheids using multiphase high-resolution spectroscopic observations and literature-derived colors. Each individual reddening value was determined as a difference between the observed (B - V) value and a calculated (B - V) value based on Castelli stellar model atmospheres and atmosphere parameters (effective temperature and gravity) previously determined through high-resolution spectroscopic analysis. This procedure was repeated for all pulsational phases at which spectra were obtained (typically 11 spectra for each star). After that, the mean reddening value for a given Cepheid was obtained. The reddening values derived were compared to values based on the use of distances and multiband photometry, reaching the general conclusion that reddening derived in this manner agrees with those from other methods.

Two-phase flow patterns and pressure drop inside horizontal tubes containing twisted-tape inserts

This paper presents an experimental study on two-phase flow patterns and pressure drop of R134a inside a 15.9 mm ID tube containing twisted-tape inserts. Experimental results were obtained in a horizontal test section for twisted-tape ratios of 3, 4, 9 and 14, mass velocities ranging from 75 to 250 kg/m(2) s and saturation temperatures of 5 and 15 degrees C. An unprecedented discussion on two-phase flow patterns inside tubes containing twisted-tape inserts is presented and the flow pattern effects on the frictional pressure drop are carefully discussed. Additionally, a new method to predict the frictional pressure drop during two-phase flow inside tubes containing twisted-tape inserts is proposed. (C) 2012 Elsevier Ltd. All rights reserved.

Modeling and simulation of severe slugging with mass transfer effects

A mathematical model and numerical simulations are presented to investigate the dynamics of gas, oil and water flow in a pipeline-riser system. The pipeline is modeled as a lumped parameter system and considers two switchable states: one in which the gas is able to penetrate into the riser and another in which there is a liquid accumulation front, preventing the gas from penetrating the riser. The riser model considers a distributed parameter system, in which movable nodes are used to evaluate local conditions along the subsystem. Mass transfer effects are modeled by using a black oil approximation. The model predicts the liquid penetration length in the pipeline and the liquid level in the riser, so it is possible to determine which type of severe slugging occurs in the system. The method of characteristics is used to simplify the differentiation of the resulting hyperbolic system of equations. The equations are discretized and integrated using an implicit method with a predictor-corrector scheme for the treatment of the nonlinearities. Simulations corresponding to severe slugging conditions are presented and compared to results obtained with OLGA computer code, showing a very good agreement. A description of the types of severe slugging for the three-phase flow of gas, oil and water in a pipeline-riser system with mass transfer effects are presented, as well as a stability map. (C) 2011 Elsevier Ltd. All rights reserved.

Boron site preference in ternary Ta and Nb boron suicides

X-ray single crystal (XSC) and neutron powder diffraction data (NPD) were used to elucidate boron site preference for five ternary phases. Ta3Si1-xBx (x=0.112(4)) crystallizes with the Ti3P-type (space group P4(2)/n) with B-atoms sharing the 8g site with Si atoms. Ta5Si3-x (x=0.03(1); Cr5B3- type) crystallizes with space group 14/mcm, exhibiting a small amount of vacancies on the 4 alpha site. Both, Ta-5(Si1-xBx)(3), X=0.568(3), and Nb-5(Si1-xBx)(3), x=0.59(2), are part of solid solutions of M5Si3 with Cr5B3-type into the ternary M-Si-B systems (M=Nb or Ta) with B replacing Si on the 8h site. The D8(8)-phase in the Nb-Si-B system crystallizes with the Ti5Ga4-type revealing the formula Nb5Si3B1-x (x=0.292(3)) with B partially filling the voids in the 2b site of the Mn5Si3 parent type. (C) 2012 Elsevier Inc. All rights reserved.

Drag reduction phenomenon in viscous oil-water dispersed pipe flow: Experimental investigation and phenomenological modeling

An experimental study on drag-reduction phenomenon in dispersed oil-water flow has been performed in a 26-mm-i.d. Twelve meter long horizontal glass pipe. The flow was characterized using a novel wire-mesh sensor based on capacitance measurements and high-speed video recording. New two-phase pressure gradient, volume fraction, and phase distribution data have been used in the analysis. Drag reduction and slip ratio were detected at oil volume fractions between 10 and 45% and high mixture Reynolds numbers, and with water as the dominant phase. Phase-fraction distribution diagrams and cross-sectional imaging of the flow suggested the presence of a higher amount of water near to the pipe wall. Based on that, a phenomenology for explaining drag reduction in dispersed flow in a flow situation where slip ratio is significant is proposed. A simple phenomenological model is developed and the agreement between model predictions and data, including data from the literature, is encouraging. (c) 2011 American Institute of Chemical Engineers AIChE J, 2012