Effects of heat treatment on the nutritional value of raw soybean selected for low trypsin inhibitor activity

1. Two broiler experiments and a layer experiments were conducted on Kunitz trypsin inhibitor (Kti) soybeans (SB) of low trypsin inhibitor (TI) activity to determine their nutritive value when included as mash in least-cost poultry diets. 2. Experiment 1 compared chick performance on the Kti or raw SB using a commercial full-fat SB meal (FFSBM) and a solvent extracted SB meal (SBM) as controls during a 20 d experimental period. Broiler experiment 2 compared Kti and raw SB, non-steamed, or steam-pelleted with and without DL-methionine supplementation added to every treatment containing 170 g SB/kg. For each broiler experiment the levels of each SB were 70, 120 and 170 g/kg with the control birds fed only 170 g SB/kg. 3. The layer experiment, compared steam-pelleted Kti and raw SB against a non-steamed Kti and raw SB each fed at two levels (70 and 110 g/kg) x 30 replicates from 29 weeks of age for 19 weeks in a completely randomised design. Production parameters were measured when diets were formulated to contain minimum required specifications and calculated apparent metabolisable energy (AME). At the completion of each trial, 2 broiler birds from each cage and 5 layer birds per treatment were killed, weighed, and their liver and pancreas weighed. 4. Both broiler experiments indicated that production parameters on the Kti SB treatments were significantly lower (P < 0.05) than on the two commercial control SB treatments. However, the Kti treatments were superior to the raw SB treatments. 5. Pancreas weight increased with increasing inclusion of both raw and Kti SB, suggesting that a TI was causing the depression in performance. The AME of the Kti SB was similar to that of commercial FFSB meal. After steam conditioning, the raw SB meal AME value of 9.5 MJ/kg dry matter (DM) was improved to 14.1 MJ/kg DM by reduced TI activity, but this AME improvement with TI activity reduction, plus the supplementation with DL-methionine on birds fed the raw SB had no effect (P > 0.05) on any parameter evaluated in experiment 2. 6. The layer experiment showed that hens on the Kti SB treatments had significantly greater live weight gain (LWG), egg weight and daily egg mass than birds given raw SB. A reduced food intake (FI) was observed in the Kti treatments but egg mass was generally similar to that on the FFSB control diet, indicating that Kti SB supported excellent egg production at an inclusion of 110 g/kg. The depressed performance observed for broiler chicks suggest that younger birds are more susceptible to the effects of SB TI.

Desenvolvimento e análise de uma rede neural artificial para estimativa da erosividade da chuva para o Estado de São Paulo

O conhecimento do valor da erosividade da chuva (R) de determinada localidade é fundamental para a estimativa das perdas de solo feitas a partir da Equação Universal de Perdas de Solo, sendo, portanto, de grande importância no planejamento conservacionista. A fim de obter estimativas do valor de R para localidades onde este é desconhecido, desenvolveu-se uma rede neural artificial (RNA) e analisou-se a acurácia desta com o método de interpolação "Inverso de uma Potência da Distância" (ID). Comparando a RNA desenvolvida com o método de interpolação ID, verificou-se que a primeira apresentou menor erro relativo médio na estimativa de R e melhor índice de confiança, classificado como "Ótimo", podendo, portanto, ser utilizada no planejamento de uso, manejo e conservação do solo no Estado de São Paulo.

Métodos de estimativa de descarga sólida em rios : análise comparativa

Transporte de sedimentos em bacias hidrográficas está relacionado com geomorfologia, ecologia fluvial, estabilidade das estruturas de engenharia e condições de navegação, dentre outros aspectos importantes para o planejamento e o controle de recursos hídricos. Existência de inúmeras variáveis envolvidas na mecânica de transporte de sedimentos e complexidade nas interações de processos físicos tornam difícil o estabelecimento de metodologias indiretas para estimativa de transporte de sedimentos em rios. Desta forma, não existe ainda metodologia universalmente aceita. O principal objetivo do presente trabalho é a análise comparativa de diferentes métodos empíricos disponíveis na literatura para estimativa de descargas sólidas em rios, considerando suas características específicas e resultados de aplicações às bacias dos rios Santa Joana e Santa Maria do Doce e microbacias Sossego e Santa Júlia, inseridas na porção da bacia do rio Doce localizada no Espírito Santo. Foram aplicados os métodos de estimativa indireta de descarga sólida: Einstein Modificado por Colby e Hembree (1955); Colby Simplificado (1957); Engelund & Hansen (1967); Ackers & White (1973); Yang (1973), Karim (1998) e Cheng (2002). Considerando as médias das estimativas de descarga sólida de material de leito (Qsml) relativas às campanhas realizadas em período chuvoso para a seção transversal do rio Doce, de maior porte, o método de Karim (1998), seguido pelo método de Ackers & White (1973), apresentou o maior valor, enquanto que o método de Yang (1973) apresentou o menor. Para os rios Santa Maria do Doce e Santa Joana e os córregos Santa Júlia e Sossego, verificou-se que o método de Ackers & White (1973), seguido de Karim (1998) e Yang (1973) apresentaram as maiores médias, enquanto que os métodos de Cheng (2002) e Engelund & Hansen (1967) apresentaram as menores. O método Simplificado de Colby apresentou as maiores estimativas de descargas sólidas totais (Qst) para todas as seções transversais de todos os cursos d'água monitorados. Concluiu-se que os diferentes métodos indiretos podem resultar em grandes diferenças em estimativas de transporte de sedimento em rios e que, desta forma, resultados de aplicação destes métodos devem ser considerados com muita cautela. Os resultados mostraram a grande importância de realização de campanhas de medição sedimentométricas para avaliação do transporte de sedimentos e definição dos melhores métodos indiretos de estimativa para cursos d'água específicos.

Tendências temporais de mortalidade por câncer de próstata no estado do Espírito Santo

Introdução: O câncer de próstata é o segundo tipo de câncer mais incidente em homens em todas as regiões do Brasil. Aproximadamente 62% dos casos diagnosticados no mundo ocorrem em homens com 65 anos ou mais, caracterizando o único fator de risco estabelecido. Objetivos: Estudar a tendência da completude do Sistema de Informação de Mortalidade (SIM), segundo as variáveis idade, raça/cor, escolaridade e estado civil no período de 2000 a 2010, no Espírito Santo, Região Sudeste e Brasil. Analisar a tendência de mortalidade por câncer de próstata na série histórica no estado do Espírito Santo (ES), no período de 1980 a 2010. Metodologia: Realizou-se um estudo descritivo baseado em dados secundários de todos os óbitos por câncer de próstata obtidos do SIM e dados do Instituto Brasileiro de Geografia e Estatística (IBGE) disponíveis no DATASUS departamento de informática do SUS (Sistema Único de Saúde), no ES, Região Sudeste e Brasil, no período de 1980 a 2010. Considerou-se as variáveis (idade, raça/cor, escolaridade e estado civil). Analisou-se o número absoluto e calculou-se o percentual de não preenchimento das informações das declarações de óbitos (DOs), que são a base de informação do SIM, nas localidades selecionadas (ES, Região Sudeste e Brasil). Analisou-se através do Pacote Estatístico para Ciências Sociais (SPSS), versão 18.0. Realizou-se uma análise inferencial com ajustes de curvas para os percentuais de dados faltantes das variáveis demográficas disponíveis no sistema do DATASUS (estado civil, escolaridade, raça/cor). E para a análise de tendência, foi realizado o cálculo do coeficiente de mortalidade por óbitos. As equações do melhor modelo e as estatísticas de ajuste (valor de R2 e o p-valor do teste F de adequação do modelo) foram obtidas do programa SPSS, versão 18.0. Resultados: No período de 2000 a 2010 a variável raça/cor, escolaridade, mostrou-se decrescente para o Brasil. A variável estado civil destacou-se por caracterizar uma tendência crescente no ES, Região Sudeste e Brasil. No período de 1980 a 2010 observou-se 3.561 óbitos no ES. Observa-se na série história que há tendência crescente de mortalidade por câncer de próstata. Conclusão: O trabalho é de grande importância para o estudo de câncer de próstata no Brasil. Identificou-se a crescente não completude dos campos de Estado Civil, enquanto a variável raça/cor foi considerada decrescente, porém com qualidade dos dados ruim. É preciso ações para que o processo de coleta dos dados seja aprimorado pela capacitação dos registradores. Nos resultados observou-se a tendência de crescimento da mortalidade, sendo necessárias ações, estratégias e políticas governamentais voltadas para a integralidade à saúde masculina.

One-sided Radial-Fundamental Matrix Estimation

For modern consumer cameras often approximate calibration data is available, making applications such as 3D reconstruction or photo registration easier as compared to the pure uncalibrated setting. In this paper we address the setting with calibrateduncalibrated image pairs: for one image intrinsic parameters are assumed to be known, whereas the second view has unknown distortion and calibration parameters. This situation arises e.g. when one would like to register archive imagery to recently taken photos. A commonly adopted strategy for determining epipolar geometry is based on feature matching and minimal solvers inside a RANSAC framework. However, only very few existing solutions apply to the calibrated-uncalibrated setting. We propose a simple and numerically stable two-step scheme to first estimate radial distortion parameters and subsequently the focal length using novel solvers. We demonstrate the performance on synthetic and real datasets.

Estimating Local Part Thickness in Midplane Meshes for Finite Element Analysis

Within the development of motor vehicles, crash safety (e.g. occupant protection, pedestrian protection, low speed damageability), is one of the most important attributes. In order to be able to fulfill the increased requirements in the framework of shorter cycle times and rising pressure to reduce costs, car manufacturers keep intensifying the use of virtual development tools such as those in the domain of Computer Aided Engineering (CAE). For crash simulations, the explicit finite element method (FEM) is applied. The accuracy of the simulation process is highly dependent on the accuracy of the simulation model, including the midplane mesh. One of the roughest approximations typically made is the actual part thickness which, in reality, can vary locally. However, almost always a constant thickness value is defined throughout the entire part due to complexity reasons. On the other hand, for precise fracture analysis within FEM, the correct thickness consideration is one key enabler. Thus, availability of per element thickness information, which does not exist explicitly in the FEM model, can significantly contribute to an improved crash simulation quality, especially regarding fracture prediction. Even though the thickness is not explicitly available from the FEM model, it can be inferred from the original CAD geometric model through geometric calculations. This paper proposes and compares two thickness estimation algorithms based on ray tracing and nearest neighbour 3D range searches. A systematic quantitative analysis of the accuracy of both algorithms is presented, as well as a thorough identification of particular geometric arrangements under which their accuracy can be compared. These results enable the identification of each technique’s weaknesses and hint towards a new, integrated, approach to the problem that linearly combines the estimates produced by each algorithm.

The estimation of the return on firms’ investments – as to ISO 9001

The aim of this paper was to estimate the return on investment in QMS (quality management systems) certification undertaken in Portuguese firms, according to the ISO 9000 series. A total of 426 certified Portuguese firms were surveyed. The response rate was 61.03 percent. The different payback periods were validated through statistical analysis and the relationship between expected and perceived payback periods was discussed. This study suggests that a firm’s sector of activity, size and degree of internationalization are related to the length of the investment in QMS certification recovery period. Furthermore, our findings suggest, that the time taken to obtain the certification is not directly related to the economic component of the certification. The majority of Portuguese firms (58.9%) took up to three years to recoup their investment and 35.5% of companies said they had not yet recovered the initial investment made. The recoup of investment was measured by the increase in the number of customers and consequent volume of deliveries, improved profitability and productivity of the company, improvement of competitive position and performance (cost savings), reduction in the number of external complaints and internal defects/scrap, achievement of some important clientele, among others. We compared our work to similar studies undertaken in other countries. This paper provides a contribution to the research related to the return on investment for costs related to the certification QMS according to ISO 9000. This paper provides a valuable contribution to the field and is one of the first studies to undertake this type of analysis in Portugal.

Integration of Individualized Management Systems (MSs) as an Aggregating Factor of Sustainable Value for Organizations: An Overview Through a Review of the Literature

Nowadays, there exist various standards for individual management systems (MSs), at least, one for each stakeholder. New ones will be published. An integrated management system (IMS) aims to integrate some or all components of the business into one coherent and efficient MS. Maximizing integration is more and more a strategic priority in that it constitutes an opportunity to eliminate and/or reduce potential factors of destruction of value for the organizations and also to be more competitive and consequently promote its sustainable success. A preliminary investigation was conducted on a Portuguese industrial company which, over the years, has been adopting gradually, in whole or in part, individualized management system standards (MSSs). A research, through a questionnaire, was performed with the objective to develop, in a real business environment, an adequate and efficient IMS-QES (quality, environment, and safety) model and to potentiate for the future a generic IMS model to integrate other MSSs. The strategy and research methods have taken into consideration the case study. It was obtained a set of relevant conclusions resulting from the statistical analyses of the responses to the survey. Globally, the investigation results, by themselves, justified and prioritized the conception of a model of development of the IMS-QES and consequent definition and validation of a structure of an IMS-QES model, to be implemented at the small- and medium-sized enterprise (SME) where the investigation was conducted.

Improving FEM crash simulation accuracy through local thickness estimation based on CAD data

In this paper, we present a method for estimating local thickness distribution in nite element models, applied to injection molded and cast engineering parts. This method features considerable improved performance compared to two previously proposed approaches, and has been validated against thickness measured by di erent human operators. We also demonstrate that the use of this method for assigning a distribution of local thickness in FEM crash simulations results in a much more accurate prediction of the real part performance, thus increasing the bene ts of computer simulations in engineering design by enabling zero-prototyping and thus reducing product development costs. The simulation results have been compared to experimental tests, evidencing the advantage of the proposed method. Thus, the proposed approach to consider local thickness distribution in FEM crash simulations has high potential on the product development process of complex and highly demanding injection molded and casted parts and is currently being used by Ford Motor Company.

Dense motion field estimation from myocardial boundary displacements

Minimally invasive cardiovascular interventions guided by multiple imaging modalities are rapidly gaining clinical acceptance for the treatment of several cardiovascular diseases. These images are typically fused with richly detailed pre-operative scans through registration techniques, enhancing the intra-operative clinical data and easing the image-guided procedures. Nonetheless, rigid models have been used to align the different modalities, not taking into account the anatomical variations of the cardiac muscle throughout the cardiac cycle. In the current study, we present a novel strategy to compensate the beat-to-beat physiological adaptation of the myocardium. Hereto, we intend to prove that a complete myocardial motion field can be quickly recovered from the displacement field at the myocardial boundaries, therefore being an efficient strategy to locally deform the cardiac muscle. We address this hypothesis by comparing three different strategies to recover a dense myocardial motion field from a sparse one, namely, a diffusion-based approach, thin-plate splines, and multiquadric radial basis functions. Two experimental setups were used to validate the proposed strategy. First, an in silico validation was carried out on synthetic motion fields obtained from two realistic simulated ultrasound sequences. Then, 45 mid-ventricular 2D sequences of cine magnetic resonance imaging were processed to further evaluate the different approaches. The results showed that accurate boundary tracking combined with dense myocardial recovery via interpolation/ diffusion is a potentially viable solution to speed up dense myocardial motion field estimation and, consequently, to deform/compensate the myocardial wall throughout the cardiac cycle. Copyright © 2015 John Wiley & Sons, Ltd.

Voxel-based registration of simulated and real patient CBCT data for accurate dental implant pose estimation

The success of dental implant-supported prosthesis is directly linked to the accuracy obtained during implant’s pose estimation (position and orientation). Although traditional impression techniques and recent digital acquisition methods are acceptably accurate, a simultaneously fast, accurate and operator-independent methodology is still lacking. Hereto, an image-based framework is proposed to estimate the patient-specific implant’s pose using cone-beam computed tomography (CBCT) and prior knowledge of implanted model. The pose estimation is accomplished in a threestep approach: (1) a region-of-interest is extracted from the CBCT data using 2 operator-defined points at the implant’s main axis; (2) a simulated CBCT volume of the known implanted model is generated through Feldkamp-Davis-Kress reconstruction and coarsely aligned to the defined axis; and (3) a voxel-based rigid registration is performed to optimally align both patient and simulated CBCT data, extracting the implant’s pose from the optimal transformation. Three experiments were performed to evaluate the framework: (1) an in silico study using 48 implants distributed through 12 tridimensional synthetic mandibular models; (2) an in vitro study using an artificial mandible with 2 dental implants acquired with an i-CAT system; and (3) two clinical case studies. The results shown positional errors of 67±34μm and 108μm, and angular misfits of 0.15±0.08º and 1.4º, for experiment 1 and 2, respectively. Moreover, in experiment 3, visual assessment of clinical data results shown a coherent alignment of the reference implant. Overall, a novel image-based framework for implants’ pose estimation from CBCT data was proposed, showing accurate results in agreement with dental prosthesis modelling requirements.

Sponsoring, brand value and social media

The increasing involvement of individuals in social media over the past decade has enabled firms to pursue new avenues in communication and sponsoring activities. Besides general research on either social media or sponsoring, questions regarding the consequences of a joint activity (sponsoring activities in social media) remain unexplored. Hence, the present study analyses whether the perceived image of the brand and the celebrity endorser credibility of a top sports team influence the perceived brand value of the sponsoring firm in a social media setting. Moreover, these effects are compared between existing customers and non-customers of the sponsoring firm. Interestingly, perceived celebrity endorser credibility plays no role in forming brand value perceptions in the case of the existing customers. Implications for marketing theory and practice are derived.