Synthesis, Characterization, and Electrocatalytic Activity toward Methanol Oxidation of Carbon-Supported Pt(x)-(RuO(2)-M)(1-x) Composite Ternary Catalysts (M = CeO(2), MoO(3), or PbO(x))

Carbon-supported platinum is commonly used as an anode electrocatalyst in low-temperature fuel cells fueled with methanol. The cost of Pt and the limited world supply are significant barriers for the widespread use of this type of fuel cell. Moreover, Pt used as anode material is readily poisoned by carbon monoxide produced as a byproduct of the alcohol oxidation. Although improvements in the catalytic performance for methanol oxidation were attained using Pt-Ru alloys, the state-of-the-art Pt-Ru catalyst needs further improvement because of relatively low catalytic activity and the high cost of noble Pt and Ru. For these reasons, the development of highly efficient ternary platinum-based catalysts is an important challenge. Thus, various compositions of ternary Pt(x)-(RuO(2)-M)(1-x)/C composites (M = CeO(2), MoO(3), or PbO(x)) were developed and further investigated as catalysts for the methanol electro-oxidation reaction. The characterization carried out by X-ray diffraction, energy-dispersive X-ray analysis, transmission electron microscopy, X-ray photoelectron spectroscopy, and cyclic voltammetry point out that the different metallic oxides were successfully deposited on the Pt/C, producing small and well-controlled nanoparticles in the range of 2.8-4.2 nm. Electrochemical experiments demonstrated that the Pt(0.50)(RuO(2)-CeO(2))(0.50)/C composite displays the higher catalytic activity toward the methanol oxidation reaction (lowest onset potential of 207 mV and current densities taken at 450 mV, which are 140 times higher than those at commercial Pt/C), followed by the Pt(0.75)(RuO(2)-MoO(3))(0.25)/C composite. In addition, both of these composites produced low quantities of formic acid and formaldehyde when compared to a commercially available Pt(0.75)-Ru(0.25)/C composite (from E-Tek, Inc.), suggesting that the oxidation of methanol occurs mainly by a pathway that produces CO(2) forming the intermediary CO(ads).

Electrochemical Behavior of Verapamil at Graphite-Polyurethane Composite Electrodes: Determination of Release Profiles in Pharmaceutical Samples

A solid graphite-polyurethane composite electrode has been used to determine release profiles of verapamil, a calcium-channel blocker. The electro-oxidation process was characterized by cyclic voltammetry and electrochemical impedance spectroscopy and showed no adsorption of analyte or oxidation products, unlike at other carbon-based electrodes. Quantification gave linear ranges up to 40molL-1 with cyclic voltammetry and detection limits of 0.7molL-1 by differential pulse and square-wave voltammetry. Commercial product samples were successfully analyzed with results equal to those from spectrophotometry. Because no electrode surface renewal is needed, this electrode material has many advantages.

Sustentabilidade e Desenvolvimento Local: Estudo de Projeto na Formação da Ecovila Viver Simples em Itamonte - MG

Eco-villages are considered models of intentional communities or sustainable communities and have been incorporated by the United Nations in the Sustainable Communities Development Programme (SCDP) as a human scale settlement. They are characterized by human activities being integrated in a non-damaging way into the natural world in such a way as to give support to healthy human development so as to be able to continue indefinitely into the future. This text assesses the extent to which a project to create the Eco-village for Simple Living in Itamonte - Minas Gerais" is successful, based on the concepts of sustainability and local development succeeds, by examining the indicators and attributes that are able to be measured in the planning phase, describing the stages and discussions of the project, as well as assessing the members 'perception of "the concepts of the Eco-village", "sustainability" and "local development". Subsequent analysis of the degree of sustainability (ecological, social, economic, spacial and cultural / spiritual) and local development, based on the social economy, demonstrated the presence of a number of aspects used to support, guide, discuss, plan and implement actions in the creation of the Eco-village being studied. This work could be used as a guide to Eco-villages during the planning phase, indicating the importance of the concepts studied, especially for some communities which are self-proclaimed "Eco-villages" but which in fact do not show even the slightest structural aspects which would describe them as such, like solidarity in the relations between participants, or construction oriented with a view to the precepts of environmental preservation. "

Excessiva atividade de remodelamento ventricular sinaliza limitada resposta terapêutica ao manejo agressivo da insuficiência cardíaca avanaçada

Introdução: Níveis de fator de necrose tumoral–alfa (TNF-α), N-peptídeo do pró-colágeno III (PIIINP) e metaloproteinase de matriz –1 (MMP-1), marcadores biológicos de remodelamento ventricular, estão elevados em pacientes com insuficiência cardíaca (IC), talvez refletindo elevadas pressões de enchimento. A correlação destes marcadores com variáveis clínicas e hemodinâmicas permanece pouco compreendida, particularmente no contexto ambulatorial da IC. Objetivo: Avaliar níveis séricos de marcadores biológicos de remodelamento ventricular em pacientes com IC, comparando tratamento guiado por ecocardiografia (ECO), buscando redução de pressões de enchimento, versus tratamento convencional (CLÍNICO), baseado em sinais e sintomas. Métodos: Ensaio clínico randomizado. Pacientes estáveis com IC e fração de ejeção menor do que 40% foram alocados entre os grupos de tratamento e submetidos a ecocardiograma e coletas de sangue no início do estudo e em 180 dias. TNF-α e MMP- 1 foram medidos por ELISA, e PIIINP, por radioimunoensaio. Resultados: Incluiu-se 80 pacientes, com 59 ± 15 anos e fração de ejeção de 26 ± 7%; 25% isquêmicos e 52% masculinos. Houve redução dos marcadores biológicos intragrupos, não havendo diferença entre os tratamentos. No grupo CLÍNICO, os níveis de TNF-α, MMP-1 e PIIINP apresentaram diferenças estatisticamente significativas entre os momentos basal e final (respectivamente, 3,11 ± 2,90 versus 1,24 ± 0,60 pg/mL p < 0,0003; 2,66 ± 1,00 versus 1,16 ± 0,40 ng/mL p < 0,0001; 6,12 ± 2,60 versus 3,89 ± 1,60 μg/L p < 0,0001). De maneira semelhante, tal diferença também foi observada no grupo ECO para os três marcadores (respectivamente, 3,90 ± 4,90 versus 1,40 ± 1,30 pg/mL p < 0,0001; 2,50 ± 0,90 versus 1,09 ± 0,40 ng/mL p < 0,0001; 6,09 ± 2,60 versus 3,50 ± 1,30 μg/L p<0,0001). Ao final da intervenção, no entanto, não foi observada diferença significativa dos valores de TNF-α , MMP-1 e PIIINP entre os dois grupos de tratamento (p = 0,7; p = 0,8; e p = 0,2; respectivamente). A combinação dos valores basais das variáveis biológicas gerou um escore que se associou significativamente com o comportamento final das pressões atrial direita e sistólica da artéria pulmonar. Pacientes com marcadores biológicos basais no quartil 75% mantiveram níveis superiores de pressões atrial direita (13 mmHg; p = 0,034) e sistólica de artéria pulmonar (60 mmHg; p = 0,007) ao final do seguimento. Conclusão: Independente do tratamento alocado, houve redução dos níveis de marcadores biológicos ao final do seguimento; no entanto, níveis basais mais elevados destes marcadores foram preditores de menor redução das pressões em átrio direito e sistólica da artéria pulmonar. Os dados sugerem que indicativos de intenso processo de remodelamento ventricular se associam à progressão da IC e a pressões de enchimento elevadas.

Development of a new analytical approach based on cellulose membrane and chelator for differentiation of labile and inert metal species in aquatic systems

A new procedure was developed in this study, based on a system equipped with a cellulose membrane and a tetraethylenepentamine hexaacetate chelator (MD-TEPHA) for in situ characterization of the lability of metal species in aquatic systems. To this end, the DM-TEPHA system was prepared by adding TEPHA chelator to cellulose bags pre-purified with 1.0 mol L-1 of HCl and NaOH solutions. After the MD-TEPHA system was sealed, it was examined in the laboratory to evaluate the influence of complexation time (0-24 h), pH (3.0, 4.0, 5.0, 6.0 and 7.0), metal ions (Cu, Cd, Fe, Mn and Ni) and concentration of organic matter (15, 30 and 60 mg L-1) on the relative lability of metal species by TEPHA chelator. The results showed that Fe and Cu metals were complexed more slowly by TEPHA chelator in the MD-TEPHA system than were Cd, Ni and Mn in all pH used. It was also found that the pH strongly influences the process of metal complexation by the MD-TEPHA system. At all the pH levels, Cd, Mn and Ni showed greater complexation with TEPHA chelator (recovery of about 95-75%) than did Cu and Fe metals. Time also affects the lability of metal species complexed by aquatic humic substances (AHS); while Cd, Ni and Mn showed a faster kinetics, reaching equilibrium after about 100 min, and Cu and Fe approached equilibrium after 400 min. Increasing the AHS concentration decreases the lability of metal species by shifting the equilibrium to AHS-metal complexes. Our results indicate that the system under study offers an interesting alternative that can be applied to in situ experiments for differentiation of labile and inert metal species in aquatic systems. (c) 2006 Elsevier B.V. All rights reserved.

Chronic exposure to sub-lethal concentration of a glyphosate-based herbicide alters hormone profiles and affects reproduction of female Jundia (Rhamdia quelen)

This work was carried out to verify the effect of a glyphosate-based herbicide on Jundia hormones (cortisol, 17 beta-estradiol and testosterone), oocyte and swim-up fry production. Earthen ponds containing Jundia females were contaminated with glyphosate (3.6 mg/L); blood samples were collected from eight females from each treatment immediately before, or at 1, 10, 20 30 and 40 days following contamination. A typical post-stress rise in cortisol levels was observed at the 20th and 40th days following exposure to glyphosate. At the 40th day, 17 beta-estradiol was decreased in the exposed females. A similar number of oocytes were stripped out from females from both groups, however, a lower number of viable swim-up fry were obtained from the herbicide exposed females, which also had a higher liver-somatic index (LSI). The results indicate that the presence of glyphosate in water was deleterious to Rhamdia quelen reproduction, altering steroid profiles and egg viability. (c) 2006 Elsevier B.V. All rights reserved.

Exigências de minerais para cabras durante a gestação: Na, K, Mg, S, Fe e Zn

O trabalho foi realizado com o objetivo de estimar a retenção e a exigência líquida dos minerais Na, K, Mg, S, Fe e Zn durante a gestação de cabras com um ou dois fetos. A estimativa de retenção foi baseada na diferença entre o total de cada mineral depositado no feto, útero, membranas, fluídos fetais e glândula mamária dos animais nas diferentes etapas da gestação e o total de cada mineral armazenado nas cabras vazias, utilizando-se o modelo de predição ln=A+Bx+Cx2, em que x=tempo de gestação. Os conteúdos de Na, K, Mg, S, Fe e Zn, durante as gestações de um e dois fetos foram de: 13,2 e 21,4 mg; 13,3 e 21,3 g; 2,1 e 3,7 mg; 5,5 e 9,3 mg; 575,5 e 981,0 mg; 112,6 e 164,7 mg nas gestações, resultando em exigências líquidas diárias de 0,13 e 0,11 g; 0,21 e 0,31 g; 0,06 e 0,11g; 0,17 e 0,21 g; 22,94 e 40,51 mg; 2,63 e 2,78 mg, respectivamente.

Cellulose-Based Bio- and Nanocomposites: A Review

Cellulose macro- and nanofibers have gained increasing attention due to the high strength and stiffness, biodegradability and renewability, and their production and application in development of composites. Application of cellulose nanofibers for the development of composites is a relatively new research area. Cellulose macro- and nanofibers can be used as reinforcement in composite materials because of enhanced mechanical, thermal, and biodegradation properties of composites. Cellulose fibers are hydrophilic in nature, so it becomes necessary to increase their surface roughness for the development of composites with enhanced properties. In the present paper, we have reviewed the surface modification of cellulose fibers by various methods. Processing methods, properties, and various applications of nanocellulose and cellulosic composites are also discussed in this paper.

Development of Nanostructured Electrochemical Sensor Based on Polymer Film Nickel-Salen for Determination of Dissolved Oxygen

An amperometric oxygen sensor based on a polymeric nickel-salen (salen = N,N '-ethylenebis(salicydeneiminato)) film coated platinum electrode was developed. The sensor was constructed by electropolymerization of nickel-salen complex at a platinum electrode in acetonitrile/tetrabuthylamonium perchlorate by cyclic voltammetry. The voltammetric behavior of the modified electrode was investigated in 0.5 mol L-1 KCl solution in the absence and presende of molecular oxygen. A significant increased of cathodic peak current (at -0.20 vs. SCE) of the modified electrode with addition of oxygen to the solution was observed. This result shows that the nickel-salen film on the surface of the electrode promotes the reduction of oxygen. The reaction can be brought about electrochemically where in the nickel(II) complex is first reduced to a nickel(I) complex at the electrode surface. The nickel(I) complex then undergoes a catalytic oxidation by the oxygen molecular in solution back to the nickel(II) complex, which can then be electrochemically re-reduced to produce an enhancement of the cathodic current. The plot of the cathodic current versus the dissolved oxygen concentration for chronoamperometry (potential fixed = -0.20 V) at the sensor was linear in the concentration range of 3.95 to 9.20 mg L-1 with concentration limit of 0.17 mg L-1 O-2. The modified electrode proposed is useful for the quality control and routine analysis of dissolved oxygen in commercial water and environmental water samples. The results obtained for the levels of dissolved oxygen are in agreement with the results obtained with an O-2 commercial sensor. (C) 2011 Published by Elsevier Ltd.

A mixture theory based method for three-dimensional modeling of reinforce concrete members with embedded crack finite elements

The paper presents a methodology to model three-dimensional reinforced concrete members by means of embedded discontinuity elements based on the Continuum Strong Discontinuous Approach (CSDA). Mixture theory concepts are used to model reinforced concrete as a 31) composite material constituted of concrete with long fibers (rebars) bundles oriented in different directions embedded in it. The effects of the rebars are modeled by phenomenological constitutive models devised to reproduce the axial non-linear behavior, as well as the bond-slip and dowel action. The paper presents the constitutive models assumed for the components and the compatibility conditions chosen to constitute the composite. Numerical analyses of existing experimental reinforced concrete members are presented, illustrating the applicability of the proposed methodology.

Flexural behavior of Sisal/Castor oil-Based Polyurethane and Sisal/Phenolic Composites

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Analysis of Semi-solid Processing for Metal Matrix Composite Synthesis Using Factorial Design

The main goal in this work is to conduct a quantitative analysis of the mechanical stir casting process for obtaining particulate metal matrix composites. A combined route of stirring at semi-solid state followed by stirring at liquid state is proposed. A fractional factorial design was developed to investigate the influence and interactions of factors as: time, rotation, initial fraction and particle size, on the incorporated fraction. The best incorporations were obtained with all factors at high levels, as well as that very long stirring periods have no strong influence being particle size and rotation the most important factors on the incorporated fraction. Particle wetting occurs during stirring at semisolid state, highlighting the importance of the interactions between particles and the alloy globularized phase. The role of the alloying element Mg as a wettability-promoting agent is discussed. The shear forces resulting from the stirring system is emphasized and understood as the effect of rotation itself added to the propeller blade geometry.

Piezoelectric effect in composite polyurethane - Ferroelectric ceramics

Flexible and free-standing films of piezoelectric composites made up of lead zirconate titanate (PZT) ceramic powder dispersed in a castor oil-based polyurethane (PU) matrix were obtained by spin coating and characterised as materials for sensor applications. The piezoelectric coefficients d(31) and d(33) were measured with the usual technique. The piezoelectric charge constant d(33) yields values up to less than or equal to 24 pC/N, even at lower PZT content (33 vol%). Some desirable properties like piezoelectricity, flexibility and good mechanical resistance show this new material to be a good alternative for use as sensors and actuators.

Dielectric and pyroelectric properties of a composite of ferroelectric ceramic and polyurethane

Flexible piezo- and pyroelectric composite was made in the thin film form by spin coating. Lead Zirconate Titanate (PZT) ceramic powder was dispersed in a castor oil-based polyurethane (PU) matrix, providing a composite with 0-3 connectivity. The dielectric data, measured over a wide range of frequency (10(-5) Hz to 105 Hz), shows a loss peak around 100 Hz related with impurities in the polymer matrix. There is also an evidence of a peak in the range 10(-4) Hz, possibly originating from the glass transition temperature T of the polymer. The pyroelectric coefficient at 34 K is 7.0x10(-5) C(.)m(-2.)K(-1) which is higher than that of P-PVDF (1X10(-5) C(.)m(-2.)K(-1)).

Síntese, caracterização, propriedades e aplicação dos sistemas Mg- Al, Zn-Al e Mg-Fe

The Layered Double Hydroxides has become extremely promising materials due to its range of applications, easily obtained in the laboratory and reusability after calcination, so the knowledge regarding their properties is of utmost importance. In this study were synthesized layered double hydroxides of two systems, Mg-Al and Zn-Al, and such materials were analyzed with X-ray diffraction and, from these data, we determined the volume density, planar atomic density, size crystallite, lattice parameters, interplanar spacing and interlayer space available. Such materials were also subjected to thermogravimetric analysis reasons for heating 5, 10, 20 and 25 ° C / min to determine kinetic parameters for the formation of metaphases HTD and HTB based on theoretical models Ozawa, Flynn-Wall Starink and Model Free Kinetics. In addition, the layered double hydroxides synthesized in this working ratios were calcined heating 2.5 ° C / min and 20 ° C / min, and tested for adsorption of nitrate anion in aqueous solution batch system at time intervals 5 min, 15 min, 30 min, 1h, 2h and 4h. Such calcined materials were also subjected to exposure to the atmosphere and at intervals of 1 week, 2 weeks and 1 month were analyzed by infrared spectroscopy to study the kinetics of regeneration determining structural called "memory effect"