Irrigation with domestic treated sewage and nitrogen fertilizing in sunflower cultivation

The objective of this study was to evaluate the productive performance of sunflower plants irrigated with different levels of domestic treated sewage and groundwater well with different doses of nitrogen. It was used randomized blocks design in split-split plots with four replications. In the plots, we evaluated the effect of two types of irrigation water, in the subplots we evaluated the five irrigation levels expressed as 25, 50, 75, 100 and 125% of the Class A pan Evaporation (CAE), and in the sub subplots, we evaluated the effect of four different doses of nitrogen (25, 50, 75 and 100 kg ha-1). The irrigation of sunflower with domestic sewage produced greater yield potential of grain and oil. The use of water from treated wastewater can replace up to 50 kg N ha-1 without affecting productivity. It is recommended for the commercial production of sunflower the use of treated sewage water with irrigation depth relative to 100% of CAE (296.64 mm) and nitrogen of 25 kg ha-1.

Technology for sugarcane agroindustry waste reuse as granulated organomineral fertilizer

Aiming to evaluate the use of sugarcane industry waste such as byproducts from vinasse concentration process, it was assessed the organomineral fertilizer BIOFOM (concentrated vinasse, filter cake, boiler ash, soot from chimneys and supplemented with mineral fertilizers). The study included characterization and agronomic potential analysis of a test plant (corn), by noting the differences between mineral fertilizers and BIOFOM fertilization until 45 days after sowing. The technology traditionally used to produce BIOFOM was based on vinasse evaporation with high heat transfer coefficients. It was observed that the technology, which can be formulated according to the needs of any crop, could be used in many cases as mineral fertilizer. Therefore, the use of this organomineral fertilizer reduces waste generation of sugarcane industry.

Corrosion behaviour of boiler tube materials during combustion of fuels containing Zn and Pb

Många förbränningsanläggningar som bränner utmanande bränslen såsom restfraktioner och avfall råkar ut för problem med ökad korrosion på överhettare och/eller vattenväggar pga. komponenter i bränslena som är korrosiva. För att minimera problemen i avfallseldade pannor hålls ångparametrarna på en relativt låg nivå, vilket drastiskt minskar energiproduktionen. Beläggningarna i avfallseldade pannor består till största delen av element som är förknippade med högtemperaturkorrosion: Cl, S, alkalimetaller, främst K och Na, och tungmetaller som Pb och Zn, och det finns också indikationer av Br-förekomst. Det låga ångtrycket i avfallseldade pannor påverkar också stålrörens temperatur i pannväggarna i eldstaden. I dagens läge hålls temperaturen normalt vid 300-400 °C. Alkalikloridorsakad (KCl, NaCl) högtemperaturkorrosion har inte rapporterats vara relevant vid såpass låga temperaturer, men närvaro av Zn- och Pb-komponenter i beläggningarna har påvisats förorsaka ökad korrosion redan vid 300-400 °C. Vid förbränning kan Zn och Pb reagera med S och Cl och bilda klorider och sulfater i rökgaserna. Dessa tungmetallföreningar är speciellt problematiska pga. de bildar lågsmältande saltblandningar. Dessa lågsmältande gasformiga eller fasta föreningar följer rökgasen och kan sedan fastna eller kondensera på kallare ytor på pannväggar eller överhettare för att sedan bilda aggressiva beläggningar. Tungmetallrika (Pb, Zn) klorider och sulfater ökar risken för korrosion, och effekten förstärks ytterligare vid närvaro av smälta. Motivet med den här studien var att få en bättre insikt i högtemperaturkorrosion förorsakad av Zn och Pb, samt att undersöka och prediktera beteendet och motståndskraften hos några stålkvaliteter som används i överhettare och pannväggar i tungmetallrika förhållanden och höga materialtemperaturer. Omfattande laboratorie-, småskale- och fullskaletest utfördes. Resultaten kan direkt utnyttjas i praktiska applikationer, t.ex. vid materialval, eller vid utveckling av korrosionsmotverkande verktyg för att hitta initierande faktorer och förstå deras effekt på högtemperaturkorrosion.

Membraanin modifiointi happo- ja alkoholikäsittelyillä

Tässä diplomityössä tutkittiin alkoholilla ja orgaanisella hapolla tehtävien esikäsittelyiden vaikutusta nanosuodatuskalvon ominaisuuksiin. Työn tarkoituksena oli parantaa nanosuodatuskalvon fraktiointiominaisuuksia sekä kasvattaa monosakkaridien suotautuvuutta. Tarkasteluissa käytetty membraani oli GE Osmonicsin valmistamaa Desal-5 DL nanosuodatuskalvoa, jota modifioitiin erilaisilla maitohappo- ja isopropanoliesikäsittelyillä. Suodatukset tehtiin kahdella erilaisella laboratoriomittakaavan levysuotimella käyttäen malliaineina väkevää sokeriliuosta sekä laimeampaa sokeri-suola-liuosta. Happo- ja alkoholiesikäsiteltyjen kalvojen vuo- ja retentioarvoja verrattiin referensseinä käytettyjen vesiliotettujen kalvojen vastaaviin arvoihin. Puhtaat esikäsitellyt kalvot analysoitiin myös tarkemmin kalvoissa tapahtuneiden muutosten ymmärtämiseksi. Suodatusten ja analyysitulosten perusteella sekä alkoholi- että happoesikäsittelyt paransivat nanosuodatuskalvon ominaisuuksia parantaen sokerivuota, heikentämättä kuitenkaan kalvon fraktiointikykyä eri moolimassan omaavien sokereiden suhteen. Hapolla saavutettiin hieman alkoholikäsittelyä suotuisammat muutokset, mutta molemmilla käsittelyillä haluttujen komponenttien retentio monesti jopa parani referenssikalvoon verrattuna. Havaitut muutokset kalvoissa olivat pääosin fysikaalisia, mutta erityisesti happokäsittely muutti kalvon rakennetta myös kemiallisesti. Molemmat käsittelyt lisäsivät myös tarkasteltavan membraanin hydrofiilisuutta.

Production of Mg(OH)2 from Mg-silicate rock for CO2 mineral sequestration

Sequestration of carbon dioxide in mineral rocks, also known as CO2 Capture and Mineralization (CCM), is considered to have a huge potential in stabilizing anthropogenic CO2 emissions. One of the CCM routes is the ex situ indirect gas/sold carbonation of reactive materials, such as Mg(OH)2, produced from abundantly available Mg-silicate rocks. The gas/solid carbonation method is intensively researched at Åbo Akademi University (ÅAU ), Finland because it is energetically attractive and utilizes the exothermic chemistry of Mg(OH)2 carbonation. In this thesis, a method for producing Mg(OH)2 from Mg-silicate rocks for CCM was investigated, and the process efficiency, energy and environmental impact assessed. The Mg(OH)2 process studied here was first proposed in 2008 in a Master’s Thesis by the author. At that time the process was applied to only one Mg-silicate rock (Finnish serpentinite from the Hitura nickel mine site of Finn Nickel) and the optimum process conversions, energy and environmental performance were not known. Producing Mg(OH)2 from Mg-silicate rocks involves a two-staged process of Mg extraction and Mg(OH)2 precipitation. The first stage extracts Mg and other cations by reacting pulverized serpentinite or olivine rocks with ammonium sulfate (AS) salt at 400 - 550 oC (preferably < 450 oC). In the second stage, ammonia solution reacts with the cations (extracted from the first stage after they are leached in water) to form mainly FeOOH, high purity Mg(OH)2 and aqueous (dissolved) AS. The Mg(OH)2 process described here is closed loop in nature; gaseous ammonia and water vapour are produced from the extraction stage, recovered and used as reagent for the precipitation stage. The AS reagent is thereafter recovered after the precipitation stage. The Mg extraction stage, being the conversion-determining and the most energy-intensive step of the entire CCM process chain, received a prominent attention in this study. The extraction behavior and reactivity of different rocks types (serpentinite and olivine rocks) from different locations worldwide (Australia, Finland, Lithuania, Norway and Portugal) was tested. Also, parametric evaluation was carried out to determine the optimal reaction temperature, time and chemical reagent (AS). Effects of reactor types and configuration, mixing and scale-up possibilities were also studied. The Mg(OH)2 produced can be used to convert CO2 to thermodynamically stable and environmentally benign magnesium carbonate. Therefore, the process energy and life cycle environmental performance of the ÅAU CCM technique that first produces Mg(OH)2 and the carbonates in a pressurized fluidized bed (FB) were assessed. The life cycle energy and environmental assessment approach applied in this thesis is motivated by the fact that the CCM technology should in itself offer a solution to what is both an energy and environmental problem. Results obtained in this study show that different Mg-silicate rocks react differently; olivine rocks being far less reactive than serpentinite rocks. In summary, the reactivity of Mg-silicate rocks is a function of both the chemical and physical properties of rocks. Reaction temperature and time remain important parameters to consider in process design and operation. Heat transfer properties of the reactor determine the temperature at which maximum Mg extraction is obtained. Also, an increase in reaction temperature leads to an increase in the extent of extraction, reaching a maximum yield at different temperatures depending on the reaction time. Process energy requirement for producing Mg(OH)2 from a hypothetical case of an iron-free serpentine rock is 3.62 GJ/t-CO2. This value can increase by 16 - 68% depending on the type of iron compound (FeO, Fe2O3 or Fe3O4) in the mineral. This suggests that the benefit from the potential use of FeOOH as an iron ore feedstock in iron and steelmaking should be determined by considering the energy, cost and emissions associated with the FeOOH by-product. AS recovery through crystallization is the second most energy intensive unit operation after the extraction reaction. However, the choice of mechanical vapor recompression (MVR) over the “simple evaporation” crystallization method has a potential energy savings of 15.2 GJ/t-CO2 (84 % savings). Integrating the Mg(OH)2 production method and the gas/solid carbonation process could provide up to an 25% energy offset to the CCM process energy requirements. Life cycle inventory assessment (LCIA) results show that for every ton of CO2 mineralized, the ÅAU CCM process avoids 430 - 480 kg CO2. The Mg(OH)2 process studied in this thesis has many promising features. Even at the current high energy and environmental burden, producing Mg(OH)2 from Mg-silicates can play a significant role in advancing CCM processes. However, dedicated future research and development (R&D) have potential to significantly improve the Mg(OH)2 process performance.

Liquid transportation and distribution during (re)wetting : impact on coated papers in printing

In many industrial applications, such as the printing and coatings industry, wetting of porous materials by liquids includes not only imbibition and permeation into the bulk but also surface spreading and evaporation. By understanding these phenomena, valuable information can be obtained for improved process control, runnability and printability, in which liquid penetration and subsequent drying play important quality and economic roles. Knowledge of the position of the wetting front and the distribution/degree of pore filling within the structure is crucial in describing the transport phenomena involved. Although exemplifying paper as a porous medium in this work, the generalisation to dynamic liquid transfer onto a surface, including permeation and imbibition into porous media, is of importance to many industrial and naturally occurring environmental processes. This thesis explains the phenomena in the field of heatset web offset printing but the content and the analyses are applicable in many other printing methods and also other technologies where water/moisture monitoring is crucial in order to have a stable process and achieve high quality end products. The use of near-infrared technology to study the water and moisture response of porous pigmented structures is presented. The use of sensitive surface chemical and structural analysis, as well as the internal structure investigation of a porous structure, to inspect liquid wetting and distribution, complements the information obtained by spectroscopic techniques. Strong emphasis has been put on the scale of measurement, to filter irrelevant information and to understand the relationship between interactions involved. The near-infrared spectroscopic technique, presented here, samples directly the changes in signal absorbance and its variation in the process at multiple locations in a print production line. The in-line non-contact measurements are facilitated by using several diffuse reflectance probes, giving the absolute water/moisture content from a defined position in the dynamic process in real-time. The nearinfrared measurement data illustrate the changes in moisture content as the paper is passing through the printing nips and dryer, respectively, and the analysis of the mechanisms involved highlight the roles of the contacting surfaces and the relative liquid carrier properties of both non-image and printed image areas. The thesis includes laboratory studies on wetting of porous media in the form of coated paper and compressed pigment tablets by mono-, dual-, and multi-component liquids, and paper water/moisture content analysis in both offline and online conditions, thus also enabling direct sampling of temporal water/moisture profiles from multiple locations. One main focus in this thesis was to establish a measurement system which is able to monitor rapid changes in moisture content of paper. The study suggests that near-infrared diffuse reflectance spectroscopy can be used as a moisture sensitive system and to provide accurate online qualitative indicators, but, also, when accurately calibrated, can provide quantification of water/moisture levels, its distribution and dynamic liquid transfer. Due to the high sensitivity, samples can be measured with excellent reproducibility and good signal to noise ratio. Another focus of this thesis was on the evolution of the moisture content, i.e. changes in moisture content referred to (re)wetting, and liquid distribution during printing of coated paper. The study confirmed different wetting phases together with the factors affecting each phase both for a single droplet and a liquid film applied on a porous substrate. For a single droplet, initial capillary driven imbibition is followed by equilibrium pore filling and liquid retreat by evaporation. In the case of a liquid film applied on paper, the controlling factors defining the transportation were concluded to be the applied liquid volume in relation to surface roughness, capillarity and permeability of the coating giving the liquid uptake capacity. The printing trials confirmed moisture gradients in the printed sheet depending on process parameters such as speed, fountain solution dosage and drying conditions as well as the printed layout itself. Uneven moisture distribution in the printed sheet was identified to be one of the sources for waving appearance and the magnitude of waving was influenced by the drying conditions.

Recovery of carboxylic acids from aqueous streams by extraction and back extraction

Separation of carboxylic acids from aqueous streams is an important part of their manufacturing process. The aqueous solutions are usually dilute containing less than 10 % acids. Separation by distillation is difficult as the boiling points of acids are only marginally higher than that of water. Because of this distillation is not only difficult but also expensive due to the evaporation of large amounts of water. Carboxylic acids have traditionally been precipitated as calcium salts. The yields of these processes are usually relatively low and the chemical costs high. Especially the decomposition of calcium salts with sulfuric acid produces large amounts of calcium sulfate sludge. Solvent extraction has been studied as an alternative method for recovery of carboxylic acids. Solvent extraction is based on mixing of two immiscible liquids and the transfer of the wanted components form one liquid to another due to equilibrium difference. In the case of carboxylic acids, the acids are transferred from aqueous phase to organic solvent due to physical and chemical interactions. The acids and the extractant form complexes which are soluble in the organic phase. The extraction efficiency is affected by many factors, for instance initial acid concentration, type and concentration of the extractant, pH, temperature and extraction time. In this paper, the effects of initial acid concentration, type of extractant and temperature on extraction efficiency were studied. As carboxylic acids are usually the products of the processes, they are wanted to be recovered. Hence the acids have to be removed from the organic phase after the extraction. The removal of acids from the organic phase also regenerates the extractant which can be then recycled in the process. The regeneration of the extractant was studied by back-extracting i.e. stripping the acids form the organic solution into diluent sodium hydroxide solution. In the solvent regeneration, the regenerability of different extractants and the effect of initial acid concentration and temperature were studied.

Vesihöyrypiirin kiertolaskenta kuplapetikattilassa

Työssä selvitetään kiertolaskennan periaatteita kuplapetikattilassa, esitetään lyhyesti kattilan toimintaperiaate ja paneudutaan alan laskentaohjelmistoihin. Luonnonkierto kattilan vesihöyrypiirissä on seurausta hydrostaattisesta paineesta, joka aiheutuu tiheyserosta nousu- ja laskuputkien välillä. Kiertolaskennassa on huomioitava kaksifaasivirtauksen ominaispiirteet. Höyry ja neste virtaavat putkistossa eri nopeuksilla, jolloin esimerkiksi painehäviön määrityksessä käytetään erilaisia korrelaatioita ja käyrästöjä. Kaksifaasivirtauksen laskennassa tarvitaan kolmea eri taseyhtälöä: energiatasetta, massatasetta ja liikemäärätasetta. Luonnonkiertokattiloissa höyrykierron suunnittelussa on kaksi pääasiallista ehtoa. Ensimmäiseksi tulee varmistaa riittävä kiertoveden massavirta, jotta vältetään höyrystinputkien puhki palaminen. Toiseksi tulee välttää höyrystinputken pinnan lämpötilavaihteluita ja värähtelyitä. Alustavassa luonnonkierron mitoituksessa turvaudutaan kokemusperäiseen tietoon. Myöhemmässä tarkemmassa mitoituksessa käytettäviä ohjelmistoja ovat NOWA sekä kaupalliset PPSD ja Apros. Laskenta lähtee liikkeelle siitä, että lasketaan ensin vesihöyrykierron massavirrat erilaisilla lämpökuormilla ja höyryntuotanto määritellään painehäviöiden perusteella. NOWA- ja PPSD- ohjelmistoilla tehtyjen esimerkkilaskelmien perusteella voidaan sanoa, että tulokset riippuvat käytetystä laskentamallista.

Characterisation of Laser Beam and Paper Material Interaction

It is known already from 1970´s that laser beam is suitable for processing paper materials. In this thesis, term paper materials mean all wood-fibre based materials, like dried pulp, copy paper, newspaper, cardboard, corrugated board, tissue paper etc. Accordingly, laser processing in this thesis means all laser treatments resulting material removal, like cutting, partial cutting, marking, creasing, perforation etc. that can be used to process paper materials. Laser technology provides many advantages for processing of paper materials: non-contact method, freedom of processing geometry, reliable technology for non-stop production etc. Especially packaging industry is very promising area for laser processing applications. However, there are only few industrial laser processing applications worldwide even in beginning of 2010´s. One reason for small-scale use of lasers in paper material manufacturing is that there is a shortage of published research and scientific articles. Another problem, restraining the use of laser for processing of paper materials, is colouration of paper material i.e. the yellowish and/or greyish colour of cut edge appearing during cutting or after cutting. These are the main reasons for selecting the topic of this thesis to concern characterization of interaction of laser beam and paper materials. This study was carried out in Laboratory of Laser Processing at Lappeenranta University of Technology (Finland). Laser equipment used in this study was TRUMPF TLF 2700 carbon dioxide laser that produces a beam with wavelength of 10.6 μm with power range of 190-2500 W (laser power on work piece). Study of laser beam and paper material interaction was carried out by treating dried kraft pulp (grammage of 67 g m-2) with different laser power levels, focal plane postion settings and interaction times. Interaction between laser beam and dried kraft pulp was detected with different monitoring devices, i.e. spectrometer, pyrometer and active illumination imaging system. This way it was possible to create an input and output parameter diagram and to study the effects of input and output parameters in this thesis. When interaction phenomena are understood also process development can be carried out and even new innovations developed. Fulfilling the lack of information on interaction phenomena can assist in the way of lasers for wider use of technology in paper making and converting industry. It was concluded in this thesis that interaction of laser beam and paper material has two mechanisms that are dependent on focal plane position range. Assumed interaction mechanism B appears in range of average focal plane position of 3.4 mm and 2.4 mm and assumed interaction mechanism A in range of average focal plane position of 0.4 mm and -0.6 mm both in used experimental set up. Focal plane position 1.4 mm represents midzone of these two mechanisms. Holes during laser beam and paper material interaction are formed gradually: first small hole is formed to interaction area in the centre of laser beam cross-section and after that, as function of interaction time, hole expands, until interaction between laser beam and dried kraft pulp is ended. By the image analysis it can be seen that in beginning of laser beam and dried kraft pulp material interaction small holes off very good quality are formed. It is obvious that black colour and heat affected zone appear as function of interaction time. This reveals that there still are different interaction phases within interaction mechanisms A and B. These interaction phases appear as function of time and also as function of peak intensity of laser beam. Limit peak intensity is the value that divides interaction mechanism A and B from one-phase interaction into dual-phase interaction. So all peak intensity values under limit peak intensity belong to MAOM (interaction mechanism A one-phase mode) or to MBOM (interaction mechanism B onephase mode) and values over that belong to MADM (interaction mechanism A dual-phase mode) or to MBDM (interaction mechanism B dual-phase mode). Decomposition process of cellulose is evolution of hydrocarbons when temperature is between 380- 500°C. This means that long cellulose molecule is split into smaller volatile hydrocarbons in this temperature range. As temperature increases, decomposition process of cellulose molecule changes. In range of 700-900°C, cellulose molecule is mainly decomposed into H2 gas; this is why this range is called evolution of hydrogen. Interaction in this range starts (as in range of MAOM and MBOM), when a small good quality hole is formed. This is due to “direct evaporation” of pulp via decomposition process of evolution of hydrogen. And this can be seen can be seen in spectrometer as high intensity peak of yellow light (in range of 588-589 nm) which refers to temperature of ~1750ºC. Pyrometer does not detect this high intensity peak since it is not able to detect physical phase change from solid kraft pulp to gaseous compounds. As interaction time between laser beam and dried kraft pulp continues, hypothesis is that three auto ignition processes occurs. Auto ignition of substance is the lowest temperature in which it will spontaneously ignite in a normal atmosphere without an external source of ignition, such as a flame or spark. Three auto ignition processes appears in range of MADM and MBDM, namely: 1. temperature of auto ignition of hydrogen atom (H2) is 500ºC, 2. temperature of auto ignition of carbon monoxide molecule (CO) is 609ºC and 3. temperature of auto ignition of carbon atom (C) is 700ºC. These three auto ignition processes leads to formation of plasma plume which has strong emission of radiation in range of visible light. Formation of this plasma plume can be seen as increase of intensity in wavelength range of ~475-652 nm. Pyrometer shows maximum temperature just after this ignition. This plasma plume is assumed to scatter laser beam so that it interacts with larger area of dried kraft pulp than what is actual area of beam cross-section. This assumed scattering reduces also peak intensity. So result shows that assumably scattered light with low peak intensity is interacting with large area of hole edges and due to low peak intensity this interaction happens in low temperature. So interaction between laser beam and dried kraft pulp turns from evolution of hydrogen to evolution of hydrocarbons. This leads to black colour of hole edges.

Effects of condensation in microchannels with a porous boundary: analytical investigation on heat transfer and meniscus shape

In two-phase miniature and microchannel flows, the meniscus shape must be considered due to effects that are affected by condensation and/or evaporation and coupled with the transport phenomena in the thin film on the microchannel wall, when capillary forces drive the working fluid. This investigation presents an analytical model for microchannel condensers with a porous boundary, where capillary forces pump the fluid. Methanol was selected as the working fluid. Very low liquid Reynolds numbers were obtained (Re~6), but very high Nusselt numbers (Nu~150) could be found due to the channel size (1.5 mm) and the presence of the porous boundary. The meniscus calculation provided consistent results for the vapor interface temperature and pressure, as well as the meniscus curvature. The obtained results show that microchannel condensers with a porous boundary can be used for heat dissipation with reduced heat transfer area and very high heat dissipation capabilities.

Hb Köln [a2b298(FG5) val-met] identified by DNA analysis in a Brazilian family

Hb Köln was identified by DNA analysis in a Brazilian patient. A four-year old Brazilian female, with jaundice since birth, presented an abnormal band, between A2 and S, in hemoglobin electrophoresis on a cellulose acetate membrane, and a band with electrophoretic migration similar to Hb C on agar gel. Thermic instability and isopropanol precipitation tests were positive. Heinz bodies were observed in the patient’s peripheral blood. Sequencing of the three exons of the b globin gene detected a transition from G to A in the first position of codon 98. This alteration does not create or abolish any known restriction site. In this case, confirmation of the mutation was accomplished by allele-specific oligonucleotide hybridization, which is a simple and fast identification method when the clinical data and hematological and electrophoretic patterns are suggestive of Hb Köln.

Polysulfidiprosessin vaikutukset höyrynkulutukseen sulfaattisellutehtaassa

Diplomityön tavoitteena on kartoittaa höyrynkulutuksen merkittävimmät muutokset sellutehtaalla siirryttäessä sulfaattimassan valmistuksesta polysulfidiselluprosessiin. Työssä esitellään sulfaattisellun valmistusprosessi ja polysulfidin vaatimat muutokset selluprosessissa erityisesti höyrynkulutuksen kannalta. Sellutehtaan höyrynkulutusta ja sen mahdollisia sekä todennettuja muutoksia tarkastellaan suhteessa tehtaan selluntuotantoon. Diplomityössä analysoidaan muutoksiin johtaneita syitä ja erityisesti peilataan niitä ennalta odotettuihin muutoksiin, joita kandidaatintyö ”Polysulfidiprosessi sulfaattisellutehtaassa” (Szepaniak 2014) esitti kirjallisuuden pohjalta. Tutkimus tehdään tutustuen dokumenttilähteisiin sekä erityisesti hankkimalla lisätietoa ja käytännön näkemystä asiantuntijahaastatteluista. Työssä käytetään esimerkkinä tyypillistä modernia sellutehdasta, jonka perusteella tarkasteltavat osaprosessit ovat valikoituneet. Tutkimustulosten perusteella esitetään jatkotutkimus- ja kehityskohteita. Sulfaattiprosessiin tehtävät muutokset käsittävät keittolipeän muuttamisen polysulfidipitoiseksi, polysulfidin valmistusprosessin (MOXY) sekä keiton muuttamisen siten, että polysulfidin vaikutus voidaan maksimoida. Polysulfidiprosessi vaikuttaa merkittävästi lipeäkiertoon ja keittämöön. Keittämön höyrynkulutus kasvaa, haihduttamon kuorma vähenee ja soodakattilan lämmöntuotanto heikkenee. Muilla osastoilla ominaishöyrynkulutuksen muutokset ovat tilastollisesti merkityksettömiä. Höyrynkulutuksella on huomattava merkitys modernin sellutehtaan tuotanto- ja kustannustehokkuuteen, sillä säästetyllä ylijäämähöyryllä voidaan tuottaa myyntisähköä. Uusiutuvan energian tuottajana ja ympäristövastuullisena toimijana sellutehtaiden on järkevää pyrkiä vähentämään omaa höyrynkulutustaan ja lisäämään sitä kautta sähköntuotantoaan.

Karbamatsepiinin Haihdutuskiteytys

Haihdutuskiteytyksessä haihdutusolosuhteilla on suuri vaikutus kiteiden muodostumiseen, joten toivottujen kidemuotojen saamiseksi prosessia on hallittava tarkasti. Kandidaatintyön tavoitteena oli tutkia puhtaiden liuottimien ja karbamatsepiiniliuosten haihtumisvuota eri olosuhteissa. Lisäksi tutkittiin kiteytysolosuhteiden vaikutusta karbamatsepiinikiteiden muodostumiseen ja rakenteeseen. Puhtaille liuottimille kokeet suoritettiin ilman virtausnopeudella 0,2 m/s lämpötiloissa 30 ºC, 40 ºC, 50 ºC ja 60 ºC, sekä ilman virtausnopeudella 0,3 m/s lämpötiloissa 40 ºC ja 50 ºC. Karbamatsepiiniliuoksille kokeet suoritettiin ilman virtausnopeudella 0,2 m/s lämpötiloissa 30 ºC ja 60 ºC sekä ilman virtausnopeudella 0,3 m/s lämpötiloissa 40 ºC ja 50 ºC. Haihdutuskiteytys suoritettiin suorakulmaisessa haihdutuskammiossa, jonka toisessa päässä oli tuulettimet virtausnopeuden säätämiseksi. Koehuoneessa vallitsi normaali ilmanpaine, ilman suhteellinen kosteus vaihteli välillä 50–65 % ja huoneen lämpötila välillä 21,2–24,1 ºC. Kuivatut kiteet analysoitiin optisella mikroskoopilla. Kaikista karbamatsepiinin vesiliuoksista kiteytyi dihydraatti-muotoa. Muutokset haihdutusolosuhteissa vaikuttivat selvästi haihtumis-voihin ja muodostuvien kiteiden rakenteeseen.

Ravinnepitoisen teollisen jäteveden tuotteistaminen

Tässä työssä selvitettiin ravinnepitoisen jäteveden väkevöintiä erityisesti ammoniumtypen ja orgaanisten happojen osalta. Konsentrointiin käytettiin pääasiassa käänteisosmoosia sekä haihdutusta, mutta myös nanosuodatusta tutkittiin. Jätevesi oli Honkajoki Oy:n lauhdevettä. Kirjallisuusosassa esiteltiin Honkajoki Oy:n toimintaa, membraanierotus-prosesseja, lihantuotannossa syntyvän jätteen ominaisuuksia sekä sen puhdistamista. Keskeisimmät suodatukset tehtiin DOW FILMTEC SW30HR -membraanilla, ja käytetty laitteisto oli DSS LabStak M20. Suodatuksia tehtiin eri pH-olosuhteissa typen ja orgaanisten happojen erottumisen kannalta optimaalisten olosuhteiden löytämiseksi. Lisäksi tutkittiin, kuinka puhtaaksi permeaatti voidaan saada uudelleensuodatuksen avulla. Työssä käytettiin myös haihdutusta lauhteen väkevöintiin. Ammoniumtypen konsentroituminen suodatuksissa oli tehokkainta pH:n ollessa 7 tai sen alle. Kaksivaiheisella suodatuksella permeaatin laatu alitti selvästi Karvianjokeen laskettaville jätevesille asetetut laatu- ja kuormitusrajat. Yhdistämällä suodatus- ja haihdutusprosessit, pystyttiin valmistamaan liuosta, jonka ammoniumtyppipitoisuus oli noin 7,6 %. Tuolloin suodatus tehtiin pH 7:ssä ja haihdutus pH 3:ssa rotavaporilla 26 mbar paineessa ja 50 °C lämpötilassa. Syöttöliuoksen tilavuuden alenema oli noin 65-kertainen. Haihdutuksessa muodostuneessa lauhteessa oli paljon orgaanisia happoja ja käytännössä ei lainkaan ammoniumtyppeä. Tuotejakeita saatiin siten kaksi kappaletta: ammoniumtyppijae ja orgaanisia happoja sisältävä jae.

Energiapuun kastelu jätetäytön suotovedellä tuhkasta ja kompostista valmistetussa kasvualustassa

Tässä työssä tutkitaan suotoveden käsittelyä käyttämällä sitä kierrätysmateriaaleista valmistetussa tuhkamullassa loppusijoitusalueen päällä kasvatettavan energiapuukasvuston kasteluun. Kyseisen toimintamallin tarkoituksena on haihduttaa suotovettä energiapuiden avulla sekä sitouttaa ravinteita ja haitta-aineita sekä kasvustoon että kasvualustaan. Tavoitteena on selvittää toimintamallin hyödyntämiskelpoisuus ja tehokkuus suotovesien käsittelymenetelmänä sekä kastelun vaikutukset energiapuun kasvuun. Työssä suoritettiin kesän ja syksyn 2014 aikana energiapuun kastelukoe Mustankorkea Oy:n jätteenkäsittelykeskuksen alueella Jyväskylässä. Kokeessa loppusijoitusalueen päälle istutettuja eri kasvuvaiheissa olevia energiapajukasvustoja sekä hybridihaapakasvustoa kasteltiin jätetäytön suotovedellä. Kokeessa käytettiin kasvualustoina tuhkamultaa, joka oli valmistettu tuhkasta, kompostista ja ylijäämämaa- aineksesta, sekä kompostia. Kasteluveden, valumavesien, kasvualustojen ja pajukasvuston ominaisuuksia seurattiin kokeen aikana analyysien avulla. Lisäksi alueen vesitaseen selvittämiseksi suoritettiin lysimetrikokeet, joissa lysimetreihin istutettuja pajuja kasteltiin suotovedellä sekä hanavedellä. Tulosten perusteella suotovesikastelu lisäsi sekä pajun että haavan kasvua. Kastelu lisäsi pajun ravinnepitoisuuksia. Se myös heikensi hieman pajun poltto-ominaisuuksia. Kasvualustan ominaisuuksiin kastelulla ei havaittu olevan vaikutuksia. Kastelumäärä, jota voidaan käyttää ilman valumia, on kokeen perusteella n. 100–600 mm/kasvukausi käytetyllä kastelujärjestelmällä. Kastelujärjestelmää kehittämällä on kuitenkin luultavasti mahdollista lisätä haihduntaa ja siten kastelumäärää merkittävästi.