Environmental evaluation of localising production as a strategy for sustainable development: a case study of two consumer goods in Jamaica

The objective of this study was to compare the life-cycle environmental impacts of changed production structures for two consumer goods (high-density polyethylene (HDPE) shopping bags and beds) in Jamaica. A scenario technique was used to construct three alternative production structures for each product; each scenario reflecting an increase in local production in Jamaica which depended on an increased supply of input materials which may be sourced: (1) externally from overseas suppliers, (2) from post-consumer recycling, and (3) locally on the island of Jamaica. These three constructed scenarios were then compared to the existing supply chain or reference scenarios of the products. The results showed that for both case products the recycling scenario was most preferable for localising production, resulting in the lowest environmental impact. This was because the production of raw materials accounted for the largest effect on total environmental impact. As such, the most immediate environmental improvements were realised by lowering the production of virgin materials. © 2007 Elsevier Ltd. All rights reserved.

Cinética de cristalização não-isotérmica de resíduos de polietileno de alta densidade (PEAD)

Nos últimos anos, a presença dos polímeros nos resíduos sólidos urbanos tem aumentado significativamente. Dentre todos os tipos de polímeros encontrados no lixo urbano, o polietileno de alta densidade (PEAD) ganha destaque, pois está presente em grande quantidade. A reciclagem de plásticos, neste âmbito, se configura como uma importante forma de reduzir a quantidade deste material nos lixões e aterros. Entretanto, sabe-se que os artefatos produzidos com material reciclado possuem propriedades inferiores. Outro ponto importante é o conhecimento da relação estrutura-propriedade, este conhecimento é fundamental na aplicação de qualquer material. Sendo assim, foram caracterizadas amostras de PEAD (embalagens pós-consumo) retiradas do lixo urbano através da calorimetria exploratória diferencial (DSC). Utilizando-se os modelos cinéticos de Avrami modificado e Liu, foi possível verificar que dependendo do tipo de carga ou colorante encontrado, há diferenças importantes na formação e morfologia dos cristais.

Avaliação de propriedades mecânicas e térmicas de compósito à base de polietileno de alta densidade e hidroxiapatita deficiente de cálcio

No presente trabalho, foram processados compósitos de polietileno de alta densidade (PEAD) com hidroxiapatita deficiente de cálcio (HA), com o objetivo de obter materiais com melhores propriedades mecânicas e bioatividade. A adição da HA deficiente de cálcio proporcionou um aumento no módulo de elasticidade (maior rigidez), menor resistência ao impacto e decréscimo do grau de cristalinidade do PEAD, proporcionando uma maior bioatividade ao material. A análise térmica exploratória (sistema não isotérmico) foi realizada por meio da técnica de calorimetria exploratória diferencial (DSC) e foram avaliados os teores de fosfato de cálcio e a velocidade de rotação da rosca no processamento dos materiais. No estudo da cristalização não-isotérmica observou-se uma diminuição da temperatura de cristalização com o aumento da taxa de resfriamento para todos os materiais sintetizados. A energia de ativação (Ea) da cristalização dos materiais foi avaliada por meio dos métodos Kissinger e Ozawa. A amostra com 5% de HA deficiente de cálcio e velocidade de processamento de 200 rpm foi a que apresentou menor valor de energia de ativação, 262 kJ/mol, menor desvio da linearidade e a que mais se assemelhou à matriz de PEAD sem HA. O teor de hidroxiapatita deficiente de cálcio não favorece o processo de cristalização devido à alta energia de ativação determinada pelos métodos descritos. Provavelmente, a velocidade de rotação, favorece a dispersão da carga na matriz de PEAD, dificultando o processo de cristalização. Na aplicação do método de Osawa-Avrami, os coeficientes de correlação indicaram perda na correlação linear. Estas perdas podem estar associadas a uma pequena percentagem de cristalização secundária e/ou à escolha das temperaturas utilizadas para determinar a velocidade de cristalização. Na determinação dos parâmetros pelo método de Mo, as menores percentagens de cristalização apresentaram um grande desvio da linearidade, com coeficiente de correlação bem menor que 1 e com o aumento da percentagem de cristalização, o desvio da linearidade diminui, ficando próximo de 1. Os resultados obtidos mostraram que o modelo de Mo e de Osawa-Avrami não foram capazes de definir o comportamento cinético dos materiais produzidos neste trabalho.

Otimização da co-pirólise de gasóleo pesado com embalagens de PEAD pós-uso utilizando planejamento fatorial

A co-pirólise é uma rota promissora, uma vez que minimiza o impacto ambiental causado pela disposição do plástico de maneira inadequada, evita seu acúmulo em lixões e permite um melhor aproveitamento de um recurso natural não-renovável, o petróleo, matéria prima importante para a geração de energia e obtenção de produtos químicos. O presente trabalho teve como objetivo a definição das condições experimentais mais propícias à obtenção de líquidos pirolíticos com alta fração de óleo diesel, resultantes da co-pirólise de polietileno de alta densidade (PEAD) pós-consumo com gasóleo pesado tilizando-se catalisador de FCC (Fluid Catalytic Cracking). Como instrumento de otimização das condições experimentais, optou-se pela Metodologia Planejamento Fatorial. Foi também estudado o efeito das condições experimentais, como: a temperatura de reação, a relação gasóleo/polietileno e a quantidade de catalisador no meio reacional. As amostras de polietileno, gasóleo e catalisador foram submetidas à co-pirólise em sistema de leito fixo, sob fluxo constante de nitrogênio, variando-se a temperatura entre 450 C a 550 C, a quantidade de PEAD no meio reacional foi de 0,2 a 0,6 g, e a quantidade de catalisador foi de zero a 0,06 g, mantendo-se fixa a quantidade de gasóleo em 2 g. Foram efetuadas as caracterizações física e química do gasóleo, polietileno pós-uso e do catalisador. Como resultado, obteve-se a produção de 87% de fração de óleo diesel em duas condições diferentes: (a) 550 0C de temperatura sem catalisador; (b) 500 0C de temperatura e 25% de catalisador FCC. Em ambos os casos, a quantidade de gasóleo pesado e PEAD foram constantes (2 g Gasóleo; 0,2 g PEAD), assim com o tempo de reação de 15 minutos. A fração de óleo diesel obtida neste estudo alcançou o poder calorífico de 44,0 MJ/Kg que é similar ao óleo diesel comercial. É importante ressaltar que em ambos os casos nenhum resíduo foi produzido, sendo uma rota ambientalmente importante para reciclagem de embalagens plásticas contaminadas com óleo lubrificante originárias de postos de serviço, visando à recuperação de ambos conteúdo energético e orgânico dos resíduos de embalagens plásticas pós-uso

Propriedades mecânicas e análise térmica de resíduos de polietileno de alta densidade (PEAD) reciclado

Atualmente grande parte dos resíduos descartados rotineiramente no Brasil é composta por material plástico como, por exemplo, o polietileno de alta densidade (PEAD), o qual é muito comum no lixo doméstico. Nesta Dissertação, embalagens de PEAD pós-consumo foram coletadas e moídas. Após processamento em extrusora, o material definido como PEAD reciclado (mistura de embalagens brancas, marfins e incolores) foi injetado e as propriedades mecânicas foram avaliadas e comparadas com uma amostra de PEAD comercial (HD7600U). A análise térmica através da calorimetria exploratória diferencial (DSC), em conjunto com a análise estatística dos resultados experimentais, também foi conduzida. Em relação à resistência à tração, a diferença entre as amostras de PEAD reciclado e PEAD comercial foram tão pouco expressivas que, dentro das condições experimentais adotadas, se pode afirmar que o material reciclado é equivalente ao comercial.Por sua vez, os modelos cinéticos aplicados na análise térmica revelaram quea amostra de PEAD comercial demonstra um processo de nucleação e crescimento dos cristais mais homogêneo e simples, embora a energia de ativação seja consideravelmente maior do que o das demais amostras de PEAD.

Yielding of engineering polymers at strain rates of up to 500 s-1

A method is described for measuring the mechanical properties of polymers in compression at strain rates in the range approximately 300-500 s-1. A gravity-driven pendulum is used to load a specimen on the end of an instrumented Hopkinson output bar and the results are processed by a microcomputer. Stress-strain curves up to high strains are presented for polycarbonate, polyethersulphone and high density polyethylene over a range of temperatures. The value of yield stress, for all three polymers, was found to vary linearly with log (strain rate) at strain rates up to 500 s-1. © 1985.

Packaging and storage studies of dried lizard fish

Packaging and storage studies of salted and dried lizard fish (Saurida sp.) have been conducted using different synthetic films like low density polyethylene (LDPE) of different gauges, high density polyethylene (HDPE) of 200 gauge, polyvinylidene chloride (PVDC) coated 400 MXXT cellophane, 100 gauge polypropylene (PP) and paper laminate of 100 gauge polythene. The films found most effective in the preliminary studies were subsequently used for packaging and storage of dried fish at atmospheric and lower temperature and humidity conditions for confirming their suitability under these conditions. Polyethylene films of higher gauges showed better results under both sets of conditions. PVDC coated cellophane film also performed satisfactorily under the latter conditions which under the former condition got easily attacked by insects. Lower temperature and humidity conditions in general enhanced the storage life of the dried product.

Bulk packages for storage and transportation of salted and dried fish

The effect of bulk packaging on the storage of salted and dried fish was studied at ambient conditions. Four different packaging systems were tried, among which gusseted type high density polyethylene woven sacks having either circular loom or traditional loom laminated with 100 gauge low density polyethylene were found to be best suited for dry fish packaging as they could withstand the hazards of handling, transportation and storage.

Influence of Annealing on Microstructure and Mechanical Properties of Isotactic Polypropylene with beta-Phase Nucleating Agent

The microstructure and mechanical properties of beta-nucleated iPP before and after being annealed at different temperatures (90-160 degrees C) have been analyzed, Annealing induced different degrees of variation in fracture toughness of beta-nucleated iPP samples. namely, slight enhancement at relatively low annealing temperatures (< 110 degrees C) and great improvement at moderate temperatures (120-130 degrees C), whereas dramatic deterioration at relatively high temperatures ( > 140 degrees C) has been observed. The variation of fracture toughness of beta-nucleated iPP is observed to be dependent on the content of beta-NA. Experiments, including scanning electronic microscope (SEM), wide-angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), small-angle X-ray scattering (SAXS), and dynamic mechanical analysis (DMA), are performed to study the variations of microstructures as well as the toughening mechanism of the beta-nucleated iPP after being annealed.

Characterization of the Microstructure of Bimodal HDPE Resin

In this work, two industrial bimodal high density polyethylene resins, resin A and resin B having similar molecular weight (M-w), molecular weight distribution (M-wD), and short-chain branching (SCB) content but different mechanical properties, were fractionated through cross-fractionation. The fractions were further, characterized by GPC, C-13 NMR, DSC AND FT IR techniques. These two resins were firstly fractionated into two franctions, i.e. high-temperature and low temperature fractions, via preparative solution crystallization fractionation. Resin A with much better mechanical properties contains more high-temperature fractions with longer crystalizable sequences. The SCB content in the low temperature fraction of resin A is lower than the of resin B. Both low-temperature fractions were then further fractionated using solvent gradient fractionation (SGF). The characterization of SGF fraction indicates that most of the branches fall into the high molecular weight chain in both low-temperature fractions.

Effect of peroxide crosslinking on thermal and mechanical properties of poly(epsilon-caprolactone)

Poly(epsilon-caprolactone) (PCL), a saturated polyester, derived from ring-opening polymerization of epsilon-caprolactone, was chemically crosslinked with various amounts of benzoyl peroxide (BPO) by a two-step method by first evenly dispersing the BPO into the PCL matrix and then crosslinking at elevated temperature. The gel fraction increased with an increase in BPO content. The modified Charlesby-Pinner equation was used to calculate the ratio of chain scission and crosslinking. The results showed that both scission and crosslinking occurred, and that crosslinking predominated over scission. The number-average molecular weight between the crosslinks determined by the rubber elasticity theory using the hot set test showed a decrease with increasing BPO content. The melting temperature and crystallinity decreased with an increase in BPO content, and the crystallization temperature increased after crosslinking. Dynamic mechanical analysis results showed a decrease in the glass transition temperature as a result of chemical crosslinking of PCL. This was explained by the observed reduction in crystallinity and the increase in free volume due to restrictions in chain packing.

Brittle-ductile transition of particle toughened polymers: influence of the matrix properties

It was theoretically pointed out that the product of the yield stress and yield strain of matrix polymer that determined the brittle-ductile transition (BDT) of particle toughened polymers. For given particle and test condition, the higher the product of the yield stress and the yield strain of the matrix polymer, the smaller the critical interparticle distance (IDc) of the blends was. This was why the IDc (0.15 mum) of the polypropylene (PP)/rubber blends was smaller than that (0.30 mum) of the nylon 66/rubber blends, and the IDc of the nylon 66/rubber blends was smaller than that (0.60 mum) of the high density polyethylene (HDPE)/rubber blends.

Preparation of fully cross-linked CNBR/PP-g-GMA and CNBR/PP/PP-g-GMA thermoplastic elastomers and their morphology, structure and properties

Binary CNBR/PP-g-GMA and ternary CNBR/PP/PP-g-GMA thermoplastic elastomers were prepared by reactive blending carboxy nitrile rubber (CNBR) powder with nanometer dimension and polypropylene functionalized with glycidyl methacrylate (PP-g-GMA). Morphology observation by using an atomic force microscope (AFM) and TEM revealed that the size of CNBR dispersed phase in CNBR/PP-g-GMA binary blends was much smaller than that of the corresponding CNBR/PP binary blends. Thermal behavior of CNBR/PP-g-GMA and CNBR/PP blends was studied by DSC. Comparing with the plain PP-g-GMA, T, of PP-g-GMA in CNBR/PP-g-GMA blends increased about 10degreesC. Both thermodynamic and kinetic effects would influence the crystallization behavior of PP-g-GMA in CNBR/PP-g-GMA blends. At a fixed content of CNBR, the apparent viscosity of the blending system increased with increasing the content of PP-g-GMA. FTIR spectrum verified that the improvement of miscibility of CNBR and PP-g-GMA was originated from the reaction between carboxy end groups of CNBR and epoxy groups of GMA grafted onto PP molecular chains. Comparing with CNBR/PP blends, the tensile strength, stress at 100% strain, and elongation at break of CNBR/PP-g-GMA blends were greatly improved.

Nanostructure and mechanical measurement of highly oriented lamellae of melt-drawn HDPE by scanning probe microscopy

Scanning probe microscopy was used to simultaneously determine the molecular chain structure and intrinsic mechanical properties, including anisotropic elastic modulus and friction, for lamellae of highly oriented high-density polyethylene (HDPE) obtained by the melt-drawn method. The molecular-scale image of the highly oriented lamellae by friction force microscopy (FFM) clearly shows that the molecular chains are aligned parallel to the drawing direction, and the periodicities along and perpendicular to the drawing direction are 0.26 and 0.50 nm, respectively. The results indicate that the exposed planes of the lamellae resulting from the melt-drawn method are (200), which is consistent with results of transmission electron microscopy and electron diffraction. Because of the high degree of anisotropy in the sample, coming from alignment of the molecular chains along the drawing direction, the measured friction force, F, determined by FFM is strongly dependent on the angle, theta, between the scanning direction and the chain axis. The force increases as theta is increased from 0 degrees (i.e., parallel to the chain axis) to 90 degrees (i.e., perpendicular to the chain axis). The structural anisotropy was also found to strongly influence the measurements of the transverse chain modulus of the polymer by the nanoindentation technique. The measured value of 13.8 GPa with transverse modulus was larger than the value 4.3 GPa determined by wide-angle X-ray diffraction, which we attributed to anisotropic deformation of the lamellae during nanoindentation measurements that was not accounted for by the elastic treatment we adopted from Oliver and Pharr. The present approach using scanning probe microscopy has the advantage that direct correlations between the nanostructure, nanotribology, and nanomechanical properties of oriented samples can be determined simultaneously and simply.

Dynamic mechanical studies of the sulfonated butyl rubber ionomers and their blends

Dynamic mechanical properties of sulfonated butyl rubber ionomers neutralized with different amine or metallic ion (zinc or barium) and their blends with polypropylene (PP), high-density polyethylene (HDPE), or styrene-butadiene-styrene (SBS) triblock copolymer were studied using viscoelastometry. The results showed that glass transition temperatures of ion pair-containing matrix and ionic domains (T-g1 and T-g2, respectively) of amine-neutralized ionomers were lower than those of ionomers neutralized with metallic ions, and the temperature range of the rubbery plateau on the storage modulus plot for amine-neutralized ionomers was narrower. The modulus of the rubbery plateau for amine-neutralized ionomers was lower than that of ionomers neutralized with zinc or barium ion. With increasing size of the amine, the temperature range for the rubbery plateau decreased, and the height of the loss peak at higher temperature increased. Dynamic mechanical properties of blends of the zinc ionomer with PP or HDPE showed that, with decreasing ionomer content, the T-m of PP or HDPE increased and T-g1 decreased, whereas T-g2 or the upper loss peak temperature changed only slightly. The T-g1 for the blend with SBS also decreased with decreasing ionomer content. The decrease of T-g1 is attributed to the enhanced compatibilization of the matrix of the ionomer-containing ion pairs with amorphous regions of PP or HDPE or the continuous phase of SBS due to the formation of thermoplastic interpenetrating polymer networks by ionic domains and crystalline or glassy domains.