Praziquantel-loaded PLGA nanoparticles: preparation and characterization

Nanoparticles containing praziquantel made of Poly (D,L-lactide-co-glycolide) were designed by an emulsion-solvent evaporation method. Two organic solvents were separately utilized as disperse phase: methylene chloride and ethyl acetate. The size of the particles prepared with the former solvent was bigger than the particles prepared with the latter. The entrapment efficiency was bigger when methylene chloride was used, 79.82% in comparison with 29.27% by using ethyl acetate. DSC and infrared studies showed that no strong chemical interaction between drug and polymer occurred. Release kinetics of praziquantel, used as a model drug, was governed not only by actual drug loading but also by particles size. The higher the drug content and the smaller the particle size resulted in faster drug release.

PLGA nanoparticles containing praziquantel: effect of formulation variables on size distribution

Praziquantel has been shown to be highly effective against all known species of Schistosoma infecting humans. Spherical nanoparticulate drug carriers made of poly(D,L-lactide-co-glycolide) acid with controlled size were designed. Praziquantel, a hydrophobic molecule, was entrapped into the nanoparticles with theoretical loading varying from 10 to 30% (w/w). This investigates the effects of some process variables on the size distribution of nanoparticles prepared by emulsion-solvent evaporation method. The results show that sonication time, PLGA and drug amounts, PVA concentration, ratio between aqueous and organic phases, and the method of solvent evaporation have a significant influence on size distribution of the nanoparticles. (C) 2004 Elsevier B.V. All rights reserved.

Monitoring of the dissemination of Salmonella in the chicken Frankfurt-sausage production line of a sausage factory in the state of São Paulo, Brazil

Poultry meat and its derivatives are among the foodstuffs considered by environmental health authorities to present the highest risks to the public. A total of 185 samples were collected in five monthly batches, from different processing stages in a sausage plant that uses mechanically-deboned chicken meat (MDCM) and tested for the presence of Salmonella. Enrichment was carried out in both Kauffman tetrathionate broth and Rappaport-Vassiliadis broth and isolation on Salmonella-Shigella agar and brilliant-green agar. Live Salmonella bacteria were isolated from six samples of the raw meat and from the emulsion, in batches three, four and five, but not from any sample in batches one or two. The six isolated strains were all classified as Salmonella Albany, which has not previously been reported in MDCM. of the two enrichment broths, Rappaport-Vassiliadis gave the better results. The Pattern of contamination suggests a probable common source, given that a new supplier was used in the third, fourth, and fifth months. It was also shown that the industrial cooking was effective in preventing Salmonella surviving in the final product.

Nanoencapsulation and Characterization of Zidovudine on Poly(L-lactide) and Poly(L-lactide)-Poly(ethylene glycol)-Blend Nanoparticles

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of Glycolic Extract of Dillenia indica L. Combined With Microcurrent Stimulation on Experimental Lesions in Wistar Rats

This study evaluated the wound healing activity of a glycolic extract of Dillenia indica (GED) prepared from the mature fruits of the plant applied alone or in combination with microcurrent stimulation to skin wounds surgically induced on the back of Wistar rats. Methods. The animals were randomly divided into six groups: (A) negative control group; (B) group receiving microcurrent application (MC; [10 mu A/2 mins]); (C) group treated with GED; (D) group treated with an emulsion containing GED; (E) group treated with GED and MC, and (F) group treated with the emulsion containing GED and MC. Tissue samples were obtained 2, 6, and 10 days after injury and underwent structural and morphometric analysis, Results. There were observed differences in wound healing among the various treatments when compared to the control group. The combination of microcurrent plus extract or microcurrent plus emulsion containing GED was advantageous in all of the studied parameters (P < 0.05) when compared to the other groups with positive effects seen regarding newly formed tissue, number of fibroblasts, and number of newly formed blood vessels. The morphometric data confirmed the structural findings. Conclusion. Microcurrent application alone or combined with GED exerted significant effects on wound healing in this experimental model. This was probably due to the efficacy of microcurrent application since the extract alone did not significantly accelerate the healing process. D indica fruit extract most likely participates in the wound healing process as a result of its anti-inflammatory properties.

Validação de método analítico por espectrofotometria UV para sistema emulsionado lipídico contendo benznidazol

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento de sistemas farmacêuticos emulsionados para veiculação gênica

Broadly speaking, the concept of gene therapy involves the transfer of a genetic material into a cell, tissue, or organ in order to cure a disease or at least improve the clinical status of a patient. Making it simple, gene therapy consists in the insertion of functional genes into cells containing defective genes by substituting, complementing or inhibiting them. The achievement of a foreigner DNA expression into a population of cells requires its transfer to the target. Therefore, it is a key issue to create systems able to transfer and protect the DNA until it reaches the target, the vectors. The disadvantages related to the use of viral vectors have encouraged efforts to develop emulsions as non-viral vectors. In fact, they are easily produced, present controllable stability and enable transfection. The aim of this work was to develop an emulsion for gene therapy and evaluate its ability to compact nucleic acids by the development of a complex with the plasmid pIRES2-EGFP. The first step was to determine the Hydrophilic Lipophilic Balance (HLB) of the Captex® 355 (oily internal phase of the emulsion) through long and short term stability assays. Based on the results, emulsions composed of Captex® 355, Tween 20® and Span 60® with 10.7 HLB were produced by three different methods: phase inversion, spontaneous emulsification and sonication. The results showed that the lowest diameter and best stability of the emulsions were achieved by the sonication method. The cationic emulsions were made by adding DOTAP to the basic emulsion. Its association with pIRES2-EGFP was evaluated by electrophoresis. Several rates of emulsion and DNA were evaluated and the results showed that 100% of the complex was formed when the rate DOTAP/DNA(nmol/µg) was 130. In conclusion, the overall results show the ability of the proposed emulsion to compact pIRES2-EGFP, which is a requirement to a successful transfection. Therefore, such formulation may be considered a promising candidate for gene therapy

Analysis of the different forms of application and types of cutting fluid used in plunge cylindrical grinding using conventional and superabrasive CBN grinding wheels

The work reported here involved an investigation into the grinding process, one of the last finishing processes carried out on a production line. Although several input parameters are involved in this process, attention today focuses strongly on the form and amount of cutting fluid employed, since these substances may be seriously pernicious to human health and to the environment, and involve high purchasing and maintenance costs when utilized and stored incorrectly. The type and amount of cutting fluid used directly affect some of the main output variables of the grinding process which are analyzed here, such as tangential cutting force, specific grinding energy, acoustic emission, diametrical wear, roughness, residual stress and scanning electron microscopy. To analyze the influence of these variables, an optimised fluid application methodology was developed (involving rounded 5, 4 and 3 turn diameter nozzles and high fluid application pressures) to reduce the amount of fluid used in the grinding process and improve its performance in comparison with the conventional fluid application method (of diffuser nozzles and lower fluid application pressure). To this end, two types of cutting fluid (a 5% synthetic emulsion and neat oil) and two abrasive tools (an aluminium oxide and a superabrasive CBN grinding wheel) were used. The results revealed that, in every situation, the optimised application of cutting fluid significantly improved the efficiency of the process, particularly the combined use of neat oil and CBN grinding wheel. (c) 2005 Elsevier Ltd. All rights reserved.

Studies on the cooling minimum quantity and conventional cooling at hardened steels in grinding process

The purpose of this work is to explain the concept of cutting fluids reasonable usage through the fluid minimum quantity in grinding processes. on that purpose, the development of a new nozzle and an own and adequate methodology should be required in order to obtain good results and compare them to the conventional methods. The analysis of the grinding wheel/cutting fluid performance was accomplished from the following input parameters: flow rate variation by nozzle diameter changes (three diameters values: 3mm, 4mm and 5mm), besides the conventional round nozzle already within the machine. Integral oil and a synthetic emulsion were used as cutting fluids and a conventional grinding wheel was employed. The workpieces were made of steel VC 131, tempered and quenched with 60HRc. Thus, as the flow rate and the nozzle diameter changes, keeping steady fluid jet velocity (equal to cutting velocity), attempted to find the best machining conditions, with the purpose to obtain a decrease on the cutting fluid volume, taking into consideration the analysis of the process output variables such as cutting strength, cutting specific energy, grinding wheel wear and surface roughness. It was verified that the 3mm diameter optimized nozzle and the integral oil, in general, was the best combination among all proposed.

Síntese e caracterização de látices acrílicos reticulados com (1,6-diacrilato propoxilato hexanodiol) via polimerização em emulsão

Latices based on acrylic acid and ethyl methacrylate, crosslinked with 1,6‐propoxylate‐hexanodiol diacrylate were synthesized via emulsion polymerization with different monomeric compositions. The resultant latices were thickened with different NaOH/(acrylic acid) molar ratios and were characterized by titrimetry, zeta potential measurements, turbidimetry, and capillary viscometry. Intrinsic viscosity was determined for an uncrosslinked copolymer, using toluene as solvent. All the latices were coagulated with NaCl and washed with water at 60°C analyzed by FTIR spectrophotometry, in order to characterize functional groups from the copolymer and crosslinking agent.

Caracterização de látices acrílicos em função da neutralização de seus grupos carboxilas

Latexes based on acrylic acid, acrylamide, ethyl methacrylate, and ethyl acrylate were synthesized via emulsion polymerization with different monomer compositions. The resultant latices were thickened with different molar ratios of NaOH to acrylic acid and were analyzed in terms of acid‐basis titrimetry, turbidimetry, rheology, and tensiometry. Titrimetry, turbidimetry, and rheometry were used to analyze factors such as carboxyl group availability and particle solubilization, tensiometry monitoring the influence of carboxyl neutralization on polymer‐surfactant interactions. For the acrylic acid content used in this work (20 wt%), the results indicated that as carboxyl groups distribution became more homogeneous, the process of latex thickening became more effective

Compósitos de borracha natural com polianilina

Compósitos de borracha natural (Hevea brasiliensis)-BN/polianilina - PANI, com diferentes composições foram obtidos através da polimerização por emulsão do monômero anilina na presença da BN e do ácido dodecilbenzeno sulfônico (DBSA). Filmes finos e homogêneos foram obtidos por prensagem a quente. Os compósitos foram caracterizados por condutividade elétrica, FTIR, UV-vis-NIR, DSC e difração de raios X. Compósito com condutividade elétrica cerca de 14 ordens de grandeza maior que a BN foi obtido. Este alto valor de condutividade é atribuído à formação da PANI no estado dopado no compósito, que foi verificado através das técnicas de UV-vis-NIR e FTIR. Os resultados obtidos com a técnica de DSC e difratometria de raios X indicaram que os polímeros são imiscíveis e que a presença da borracha não altera significantemente a fase cristalina da PANI-DBSA no compósito.

Caracterização de poliacrilamida parcialmente hidrolisada em regime concentrado

A partially hydrolyzed polyacrylamide (HPAM) is a copolymer composed of acrylamide and sodium acrylate. Due to its wide range of applications there are different methods for its quantification and characterization in solution systems. Evaluation of C* is important to describe the transition from dilute to semi-dilute, behavior, when the solution will have its characteristic viscosity at concentrations above C*. This dissertation describes the determination of the critical concentration of overlap C* by potentiometry of partially hydrolyzed polyacrylamide - HPAM under acidic conditions. Based on the law of mass action and the proper treatment of the constant of aggregate formation, polymer molecular weight, degree of polymerization and hydrolysis were calculated. The inflection point was determined by the intersection of the resulting equation and mathematical development, statistically satisfy the experimental points relating the number of moles of monomers (n), equilibrium constant of formation of the entanglements (K*), pH, C* and acidity constant of the polymer (Ka). The viscometric parameters of C* showed a percentage difference compared to potentiometers. The results for the determination of C*, and degree of copolymerization molar mass proved to be a simple alternative for the characterization of polymers with protonated monomers and water soluble

Síntese e caracterização de poliacrilamidas modificadas para utilização na indústria do petróleo

Modified polyacrylamides with ≅ 0.2 mol % of N,N-dihexylacrylamide and hydrolysis degree from 0 to 25 % were synthesized by micellar copolymerization. The hydrophobic monomer was obtained by the reaction between acryloyl chloride and N,Ndihexylamine and characterized by infrared (IR) and proton nuclear magnetic resonance (1H NMR) spectroscopy. The polymer molecular structures were determined through 1H and 13C NMR spectroscopy and the polymers were studied in dilute and semi-dilute regimes by viscometry, rheometry, static light scattering and photon correlation spectroscopy, at the temperature range from 25 to 55 ºC. The data obtained by viscometry showed that the intrinsic viscosity from the hydrolyzed polymers is larger than the precursor polymers at the same ionic strength. The comparison between the charged polymers showed that the polymer with higher hydrolysis degree has a more compact structure in formation water (AFS). The increase of temperature led to an enhanced reduced viscosity to the polymers in Milli-Q water (AMQ), although, in brine, only the unhydrolyzed polymer had an increase in the reduced viscosity with the temperature, and the hydrolyzed derivatives had a decrease in the reduced viscosity. The static light scattering (SLS) analyses in salt solutions evidenced a decrease of weight-average molecular weight (⎯Mw) with the increase of the hydrolysis degree, due to the reduction of the thermodynamic interactions between polymer and solvent, which was evidenced by the decrease of the second virial coefficient (A2). The polymers showed more than one relaxation mode in solution, when analyzed by photon correlation spectroscopy, and these modes were attributed to isolated coils and aggregates of several sizes. The aggregation behavior depended strongly on the ionic strength, and also on the temperature, although in a lower extension. The polymers showed large aggregates in all studied conditions, however, their solutions did not displayed a good increase in water viscosity to be used in enhanced oil recovery (EOR) processes

Partículas inteligentes de poli (nisopropilacrilamida), quitosana e poli (ácido acrílico): efeito da temperatura e do pH sobre suas propriedades em suspensões aquosas

The present study describes the stability and rheological behavior of suspensions of poly (N-isopropylacrylamide) (PNIPAM), poly (N-isopropylacrylamide)-chitosan (PNIPAMCS), and poly (N-isopropylacrylamide)-chitosan-poly (acrylic acid) (PNIPAM-CS-PAA) crosslinked particles sensitive to pH and temperature. These dual-sensitive materials were simply obtained by one-pot method, via free-radical precipitation copolymerization with potassium persulfate, using N,N -methylenebisacrylamide (MBA) as a crosslinking agent. Incorporation of the precursor materials into the chemical networks was confirmed by elementary analysis and infrared spectroscopy. The influence of external stimuli such as pH and temperature, or both, on particle behavior was investigated through rheological measurements, visual stability tests and analytical centrifugation. The PNIPAM-CS particles showed higher stability in acid and neutral media, whereas PNIPAM-CS-PAA particles were more stable in neutral and alkaline media, both below and above the LCST of poly (Nisopropylacrylamide) (stability data). This is due to different interparticle interactions, as well as those between the particles and the medium (also evidenced by rheological data), which were also influenced by the pH and temperature of the medium. Based on the results obtained, we found that the introduction of pH-sensitive polymers to crosslinked poly (Nisopropylacrylamide) particles not only produced dual-sensitive materials, but allowed particle stability to be adjusted, making phase separation faster or slower, depending on the desired application. Thus, it is possible to adapt the material to different media