On-line FTIR spectroscopic investigations of methanol oxidation in a direct methanol fuel cell

A real-time Fourier transform infrared spectroscopy (FTIRS) analysis of the products of methanol oxidation in a prototype direct-methanol fuel cell operating at high temperatures (150 to 185°C) is reported here. The methanol oxidation products on platinum black and platinum-ruthenium catalyst surfaces were determined as a function of the fuel cell operating temperature, current density, and methanol/water mole ratio. Neither formaldehyde nor formic acid was detected in anode exhaust gas at all cell operating conditions. The product distributions of methanol oxidation obtained by on-line FTIRS are consistent with our previous results obtained by on-line mass spectroscopy under similar conditions. With pure methanol in anode feed, methanaldimethylacetal was found to be the main product, methyl formate and CO were also found. However, when water was present in the anode feed, the main product was CO , and the formation of methanaldimethylacetal and methyl formate decreased significantly with increase of the water/methanol mole ratio. Increase of cell operating temperature enhanced the formation of CO and decreased the formation of methanaldimethylacetal and methyl formate. Pt/Ru catalyst is more active for methanol oxidation and has a higher selectivity toward CO formation than Pt-black. Nearly complete methanol oxidation, i.e., the product was almost exclusively CO , was achieved using a Pt/Ru catalyst and a water/methanol mole ratio of 2 or higher in the anode feed at a temperature of 185°C or above.

Preliminary analysis of organic Rankine cycles to improve vehicle efficiency

This paper presents the background rationale and key findings for a model-based study of supercritical waste heat recovery organic Rankine cycles. The paper’s objective is to cover the necessary groundwork to facilitate the future operation of a thermodynamic organic Rankine cycle model under realistic thermodynamic boundary conditions for performance optimisation of organic Rankine cycles. This involves determining the type of power cycle for organic Rankine cycles, the circuit configuration and suitable boundary conditions. The study focuses on multiple heat sources from vehicles but the findings are generally applicable, with careful consideration, to any waste heat recovery system. This paper introduces waste heat recovery and discusses the general merits of organic fluids versus water and supercritical operation versus subcritical operation from a theoretical perspective and, where possible, from a practical perspective. The benefits of regeneration are investigated from an efficiency perspective for selected subcritical and supercritical conditions. A simulation model is described with an introduction to some general Rankine cycle boundary conditions. The paper describes the analysis of real hybrid vehicle data from several driving cycles and its manipulation to represent the thermal inertia for model heat input boundary conditions. Basic theory suggests that selecting the operating pressures and temperatures to maximise the Rankine cycle performance is relatively straightforward. However, it was found that this may not be the case for an organic Rankine cycle operating in a vehicle. When operating in a driving cycle, the available heat and its quality can vary with the power output and between heat sources. For example, the available coolant heat does not vary much with the load, whereas the quantity and quality of the exhaust heat varies considerably. The key objective for operation in the vehicle is optimum utilisation of the available heat by delivering the maximum work out. The fluid selection process and the presentation and analysis of the final results of the simulation work on organic Rankine cycles are the subjects of two future publications.

Integrating intrinsic and global kinetics as a dual kinetic model for automotive catalysis

The majority of the kinetic models employed in catalytic after-treatment of exhaust emissions use a global kinetic approach owing to the simplicity because one expression can account for all the steps in a reaction. The major drawback of this approach is the limited predictive capabilities of the models. The intrinsic kinetic approach offers much more information about the processes occurring within the catalytic converter; however, it is significantly more complex and time consuming to develop. In the present work, a methodology which allows accessing a model that combines the simplicity of the global kinetic approach and the accuracy of the intrinsic kinetic approach is reported. To assess the performance of this new approach, the oxidation of carbon monoxide in the presence of nitric oxide as well as a driving cycle was investigated. The modelling of carbon monoxide oxidation with oxygen which utilised the intrinsic kinetic approach with the global kinetic approach was used for the carbon monoxide + nitric oxide reaction (and all remaining reactions for the driving cycle). The comparison of the model results for the dual intrinsic + global kinetic approach with the experimental data obtained for both the reactor and the driving cycle indicate that the dual approach is promising with results significantly better than those obtained with only the global kinetics approach.

ELM-induced transient tungsten melting in the JET divertor

The original goals of the JET ITER-like wall included the study of the impact of an all W divertor on plasma operation (Coenen et al 2013 Nucl. Fusion 53 073043) and fuel retention (Brezinsek et al 2013 Nucl. Fusion 53 083023). ITER has recently decided to install a full-tungsten (W) divertor from the start of operations. One of the key inputs required in support of this decision was the study of the possibility of W melting and melt splashing during transients. Damage of this type can lead to modifications of surface topology which could lead to higher disruption frequency or compromise subsequent plasma operation. Although every effort will be made to avoid leading edges, ITER plasma stored energies are sufficient that transients can drive shallow melting on the top surfaces of components. JET is able to produce ELMs large enough to allow access to transient melting in a regime of relevance to ITER.

Transient W melt experiments were performed in JET using a dedicated divertor module and a sequence of I-P = 3.0 MA/B-T = 2.9 T H-mode pulses with an input power of P-IN = 23 MW, a stored energy of similar to 6 MJ and regular type I ELMs at Delta W-ELM = 0.3 MJ and f(ELM) similar to 30 Hz. By moving the outer strike point onto a dedicated leading edge in the W divertor the base temperature was raised within similar to 1 s to a level allowing transient, ELM-driven melting during the subsequent 0.5 s. Such ELMs (delta W similar to 300 kJ per ELM) are comparable to mitigated ELMs expected in ITER (Pitts et al 2011 J. Nucl. Mater. 415 (Suppl.) S957-64).

Although significant material losses in terms of ejections into the plasma were not observed, there is indirect evidence that some small droplets (similar to 80 mu m) were released. Almost 1 mm (similar to 6 mm(3)) of W was moved by similar to 150 ELMs within 7 subsequent discharges. The impact on the main plasma parameters was minor and no disruptions occurred. The W-melt gradually moved along the leading edge towards the high-field side, driven by j x B forces. The evaporation rate determined from spectroscopy is 100 times less than expected from steady state melting and is thus consistent only with transient melting during the individual ELMs. Analysis of IR data and spectroscopy together with modelling using the MEMOS code Bazylev et al 2009 J. Nucl. Mater. 390-391 810-13 point to transient melting as the main process. 3D MEMOS simulations on the consequences of multiple ELMs on damage of tungsten castellated armour have been performed.

These experiments provide the first experimental evidence for the absence of significant melt splashing at transient events resembling mitigated ELMs on ITER and establish a key experimental benchmark for the MEMOS code.

Improving fuel economy application of the organic Rankine Cycle on a hybrid bus

Globally vehicle operators are experiencing rising fuel costs and increased
running expenses as governments around the world attempt to decrease carbon dioxide emissions and fossil fuel consumption, due to global warming and the drive to reduce dependency on fossil fuels. Recent advances in hybrid vehicle design have made great strides towards more efficient operation, with regenerative braking being widely used to capture otherwise lost energy. In this paper a hybrid series bus is developed a step further, by installing another method of energy capture on the vehicle. In this case, it is in the form of the Organic Rankine Cycle (ORC). The waste heat expelled to the exhaust and coolant streams is recovered and converted to electrical energy which is then stored in the hybrid vehicles batteries. The electrical energy can then be used for the auxiliary power circuit or to assist in vehicle propulsion, thus reducing the load on the engine, thereby improving the overall fuel economy of the vehicle and reducing carbon dioxide emissions.

Analysis of electric vehicle charging using the traditional generation expansion planning analysis tool WASP-IV

Electric vehicles (EV) are proposed as a measure to reduce greenhouse gas emissions in transport and support increased wind power penetration across modern power systems. Optimal benefits can only be achieved, if EVs are deployed effectively, so that the exhaust emissions are not substituted by additional emissions in the electricity sector, which can be implemented using Smart Grid controls. This research presents the results of an EV roll-out in the all island grid (AIG) in Ireland using the long term generation expansion planning model called the Wien Automatic System Planning IV (WASP-IV) tool to measure carbon dioxide emissions and changes in total energy. The model incorporates all generators and operational requirements while meeting environmental emissions, fuel availability and generator operational and maintenance constraints to optimize economic dispatch and unit commitment power dispatch. In the study three distinct scenarios are investigated base case, peak and off-peak charging to simulate the impacts of EV’s in the AIG up to 2025.

A techno-economic evaluation of changing from conventional vehicles to range extended electric vehicles

Transportation accounts for 22% of greenhouse gas emissions in the UK, and increases to 25% in Northern Ireland. Surface transport carbon dioxide emissions, consisting of road and rail, are dominated by cars. Demand for mobility is rising rapidly and vehicle numbers are expected to more than double by 2050. Car manufacturers are working towards reducing their carbon footprint through improving fuel efficiency and controlling exhaust emissions. Fuel efficiency is now a key consideration of consumers purchasing a new vehicle. While measures have been taken to help to reduce pollutants, in the future, alternative technologies will have to be used in the transportation industry to achieve sustainability. There are currently many alternatives to the market leader, the internal combustion engine. These alternatives include hydrogen fuel cell vehicles and electric vehicles, a term which is widely used to cover battery electric vehicles, plug-in hybrid electric vehicles and extended-range electric vehicles. This study draws direct comparisons measuring the differing performance in terms of fuel consumption, carbon emissions and range of a typical family saloon car using different fuel types. These comparisons will then be analysed to see what effect switching from a conventionally fuelled vehicle to a range extended electric vehicle would have not only on the end user, but also the UK government.

Modelling of Organic Rankine Cycle for Waste Heat Recovery Process in Supercritical Condition

Organic Rankine Cycle (ORC) is the most commonly used method for recovering energy from small sources of heat. The investigation of the ORC in supercritical condition is a new research area as it has a potential to generate high power and thermal efficiency in a waste heat recovery system. This paper presents a steady state ORC model in supercritical condition and its simulations with a real engine’s exhaust data. The key component of ORC, evaporator, is modelled using finite volume method, modelling of all other components of the waste heat recovery system such as pump, expander and condenser are also presented. The aim of this paper is to investigate the effects of mass flow rate and evaporator outlet temperature on the efficiency of the waste heat recovery process. Additionally, the necessity of maintaining an optimum evaporator outlet temperature is also investigated. Simulation results show that modification of mass flow rate is the key to changing the operating temperature at the evaporator outlet.

Catalyst Deactivation on a Two-Stroke Engine

With the legislative demands increasing on recreational vehicles and utility engined applications, the two-stroke engine is facing increasing pressure to meet these requirements. One method of achieving the required reduction is via the introduction of a catalytic converter. The catalytic converter not only has to deal with the characteristically higher CO and HC concentration, but also any oil which is added to lubricate the engine. In a conventional two-stroke engine with a total loss lubrication system, the oil is either scavenged straight out the exhaust port or is entrained, involved in combustion and is later exhausted. This oil can have a significant effect on the performance of the catalyst.
To investigate the oiling effect, three catalytic converters were aged using a 400cm₃ DI two-stroke engine. A finite level of oil was added to the inlet air of the engine to lubricate the internal workings. The oil flow rate is independent of the engine speed and load.

Three catalysts were aged for 50 hours, experiencing a constant space velocity and set engine conditions. The engine was fueled on petrol and later on propane to eliminate the effects, if any, of petrol additives on catalyst deactivation. The oiling rate was varied to investigated deactivation from oil contamination. Post-mortem analysis was performed on the three catalysts. This consisted of a controlled light-off test performed on a catalyst rig, during which period, temperatures were measured and recorded towere aged for 50 hours, experiencing a constant space velocity and set engine conditions. The engine was fueled on petrol and later on propane to eliminate the effects, if any, of petrol additives on catalyst deactivation. The oiling rate was varied to investigated deactivation from oil contamination. Post-mortem analysis was performed on the three catalysts. This consisted of a controlled light-off test performed on a catalyst rig, during which period, temperatures were measured and recorded to find out where deactivation of each catalyst was occurring. The recorded results were all analyzed and these showed that from the measured light-off temperatures the aged catalysts behaved similarly. However the pattern in the light-off was significantly different when the engine was fueled by propane as opposed to gasoline.

A Parametric Study Of A Turbogenerator On A Diesel-Electric Hybrid Bus

The fuel consumption of automotive vehicles has become a prime consideration to manufacturers and operators as fuel prices continue to rise steadily, and legislation governing toxic emissions becomes ever more strict. This is particularly true for bus operators as government fuel subsidies are cut or removed.

In an effort to reduce the fuel consumption of a diesel-electric hybrid bus, an exhaust recovery turbogenerator has been selected from a wide ranging literature review as the most appropriate method of recovering some of the wasted heat in the exhaust line. This paper examines the effect on fuel consumption of a turbogenerator applied to a 2.4-litre diesel engine.

A validated one-dimensional engine model created using Ricardo WAVE was used as a baseline, and was modified in subsequent models to include a turbogenerator downstream, and in series with, the turbocharger turbine. A fuel consumption map of the modified engine was produced, and an in-house simulation tool was then used to examine the fuel economy benefit delivered by the turbogenerator on a bus operating on various drive-cycles.

A parametric study is presented which examined the performance of turbogenerators of various size and power output. The operating strategy of the turbogenerator was also discussed with a view to maximising turbine efficiency at each operating point.

The performance of the existing turbocharger on the hybrid bus was also investigated; both the compressor and turbine were optimised and the subsequent benefits to the fuel consumption of the vehicle were shown.

The final configuration is then presented and the overall improvement in fuel economy of the hybrid bus was determined over various drive-cycles.

Investigations Into the Performance of a Turbogenerated Biogas Engine During Speed Transients

Turbogenerating is a form of turbocompounding whereby a Turbogenerator is placed in the exhaust stream of an internal combustion engine. The Turbogenerator converts a portion of the expelled energy in the exhaust gas into electricity which can then be used to supplement the crankshaft power. Previous investigations have shown how the addition of a Turbogenerator can increase the system efficiency by up to 9%. However, these investigations pertain to the engine system operating at one fixed engine speed. The purpose of this paper is to investigate how the system and in particular the Turbogenerator operate during engine speed transients. On turbocharged engines, turbocharger lag is an issue. With the addition of a Turbogenerator, these issues can be somewhat alleviated. This is done by altering the speed at which the Turbogenerator operates during the engine’s speed transient. During the transients, the Turbogenerator can be thought to act in a similar manner to a variable geometry turbine where its speed can cause a change in the turbocharger turbine’s pressure ratio. This paper shows that by adding a Turbogenerator to a turbocharged engine the transient performance can be enhanced. This enhancement is shown by comparing the turbogenerated engine to a similar turbocharged engine. When comparing the two engines, it can be seen that the addition of a Turbogenerator can reduce the time taken to reach full power by up to 7% whilst at the same time, improve overall efficiency by 7.1% during the engine speed transient.

Biodiesel fuel formulation

O consumo de energia a nível mundial aumenta a cada dia, de forma inversa aos recursos fósseis que decrescem de dia para dia. O sector dos transportes é o maior consumidor deste recurso. Face ao actual cenário urge encontrar uma solução renovável e sustentável que permita não só, diminuir a nossa dependência de combustíveis fósseis mas fundamentalmente promover a sua substituição por energias de fontes renováveis. O biodiesel apresenta-se na vanguarda das alternativas aos combustiveis derivados do petróleo, para o sector dos transportes, sendo considerado uma importante opção a curto prazo, uma vez que o seu preço pode ser competitivo com o diesel convencional, e para a sua utilização o motor de combustão não necessita de alterações. O biodiesel é uma mistura líquida, não tóxica, biodegradável de ésteres de ácidos gordos, sem teor de enxofre ou compostos aromáticos, apresenta boa lubricidade, alto número de cetano, e origina emissões gasosas mais limpas. O presente trabalho contribui para um melhor conhecimento da dependência das propriedades termofisicas do biodiesel com a sua composição. A publicação de novos dados permitirá o desenvolvimento de modelos mais fiáveis na previsão do comportamento do biodiesel. As propriedades densidade e viscosidade são o espelho da composição do biodiesel, uma vez que dependem directamente da matéria prima que lhe deu origem, mais do que do processo de produção. Neste trabalho os dados medidos de densidade e viscosidade de biodiesel foram testados com vários modelos e inclusivamente foram propostos novos modelos ajustados para esta família de compostos. Os dados medidos abrangem uma ampla gama de temperaturas e no caso da densidade também foram medidos dados a alta pressão de biodiesel e de alguns ésteres metilico puros. Neste trabalho também são apresentados dados experimentais para o equilíbrio de fases sólido-liquído de biodiesel e equlibrio de fases líquidolíquido de alguns sistemas importantes para a produção de biodiesel. Ambos os tipos de equilíbrio foram descritos por modelos desenvolvidos no nosso laboratório. Uma importância especial é dado aqui a propriedades que dependem do perfil de ácidos gordos da matéria-prima além de densidade e viscosidade; o índice de iodo e temperature limite de filtrabalidade são aqui avaliados com base nas considerações das normas. Os ácidos gordos livres são um sub-produto de refinação de óleo alimentar, que são removidos na desodoração, no processo de purificação do óleo. A catálise enzimática é aqui abordada como alternativa para a conversão destes ácidos gordos livres em biodiesel. Estudou-se a capacidade da lipase da Candida antartica (Novozym 435) para promover a esterificação de ácidos gordos livres com metanol ou etanol, utilizando metodologia de superfície de resposta com planeamento experimental. Avaliou-se a influência de diversas variáveis no rendimento da reacção.

Control design for multicast-aware class-based networks

The expectations of citizens from the Information Technologies (ITs) are increasing as the ITs have become integral part of our society, serving all kinds of activities whether professional, leisure, safety-critical applications or business. Hence, the limitations of the traditional network designs to provide innovative and enhanced services and applications motivated a consensus to integrate all services over packet switching infrastructures, using the Internet Protocol, so as to leverage flexible control and economical benefits in the Next Generation Networks (NGNs). However, the Internet is not capable of treating services differently while each service has its own requirements (e.g., Quality of Service - QoS). Therefore, the need for more evolved forms of communications has driven to radical changes of architectural and layering designs which demand appropriate solutions for service admission and network resources control. This Thesis addresses QoS and network control issues, aiming to improve overall control performance in current and future networks which classify services into classes. The Thesis is divided into three parts. In the first part, we propose two resource over-reservation algorithms, a Class-based bandwidth Over-Reservation (COR) and an Enhanced COR (ECOR). The over-reservation means reserving more bandwidth than a Class of Service (CoS) needs, so the QoS reservation signalling rate is reduced. COR and ECOR allow for dynamically defining over-reservation parameters for CoSs based on network interfaces resource conditions; they aim to reduce QoS signalling and related overhead without incurring CoS starvation or waste of bandwidth. ECOR differs from COR by allowing for optimizing control overhead minimization. Further, we propose a centralized control mechanism called Advanced Centralization Architecture (ACA), that uses a single state-full Control Decision Point (CDP) which maintains a good view of its underlying network topology and the related links resource statistics on real-time basis to control the overall network. It is very important to mention that, in this Thesis, we use multicast trees as the basis for session transport, not only for group communication purposes, but mainly to pin packets of a session mapped to a tree to follow the desired tree. Our simulation results prove a drastic reduction of QoS control signalling and the related overhead without QoS violation or waste of resources. Besides, we provide a generic-purpose analytical model to assess the impact of various parameters (e.g., link capacity, session dynamics, etc.) that generally challenge resource overprovisioning control. In the second part of this Thesis, we propose a decentralization control mechanism called Advanced Class-based resource OverpRovisioning (ACOR), that aims to achieve better scalability than the ACA approach. ACOR enables multiple CDPs, distributed at network edge, to cooperate and exchange appropriate control data (e.g., trees and bandwidth usage information) such that each CDP is able to maintain a good knowledge of the network topology and the related links resource statistics on real-time basis. From scalability perspective, ACOR cooperation is selective, meaning that control information is exchanged dynamically among only the CDPs which are concerned (correlated). Moreover, the synchronization is carried out through our proposed concept of Virtual Over-Provisioned Resource (VOPR), which is a share of over-reservations of each interface to each tree that uses the interface. Thus, each CDP can process several session requests over a tree without requiring synchronization between the correlated CDPs as long as the VOPR of the tree is not exhausted. Analytical and simulation results demonstrate that aggregate over-reservation control in decentralized scenarios keep low signalling without QoS violations or waste of resources. We also introduced a control signalling protocol called ACOR Protocol (ACOR-P) to support the centralization and decentralization designs in this Thesis. Further, we propose an Extended ACOR (E-ACOR) which aggregates the VOPR of all trees that originate at the same CDP, and more session requests can be processed without synchronization when compared with ACOR. In addition, E-ACOR introduces a mechanism to efficiently track network congestion information to prevent unnecessary synchronization during congestion time when VOPRs would exhaust upon every session request. The performance evaluation through analytical and simulation results proves the superiority of E-ACOR in minimizing overall control signalling overhead while keeping all advantages of ACOR, that is, without incurring QoS violations or waste of resources. The last part of this Thesis includes the Survivable ACOR (SACOR) proposal to support stable operations of the QoS and network control mechanisms in case of failures and recoveries (e.g., of links and nodes). The performance results show flexible survivability characterized by fast convergence time and differentiation of traffic re-routing under efficient resource utilization i.e. without wasting bandwidth. In summary, the QoS and architectural control mechanisms proposed in this Thesis provide efficient and scalable support for network control key sub-systems (e.g., QoS and resource control, traffic engineering, multicasting, etc.), and thus allow for optimizing network overall control performance.

A new combined joules supercritical rankine cycle exergetic analysis and optimization

The application of a supercritical Rankine cycle in combined cycles does not happen in today’s thermoelectric power stations. Nevertheless, the most recent development in gas turbines, that allows a high efficiency and high exhaust gases temperatures, and the improvement of high pressure and temperature alloys, makes this cycle possible. This study’s intent is to prove the viability of this combined cycle, since it can break the 60% efficiency barrier, which is the plafond in actual power stations. To attain this target, several configurations for this cycle have been simulated, optimized and analyzed [1]. The simulations were done with the computational program IPSEpro [2] and the optimizations were effectuated with software developed for the effect, using the DFP method [3]. In parallel with the optimization that claims the cycle’s efficiency maximization, an exergetic analysis was also made [4] to all the cycle components. In opposite to what happens in subcritical combined cycles, it was demonstrated that in supercritical combined cycles the higher efficiency takes place with a single steam pressure in the heat recovery steam generator (HRSG).

Ventilação mista em edifícios de habitação

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Edificações