Aços avançados de alta resistência: avaliação da microestrutura e propriedades dos aços DP 600 E DP 780

This work aims to study the Dual-Phase 600 and 780 steels, which are part of technology development project materials for the automotive industry. It is worth underscoring the antagonistic properties as the Dual-Phase steel assemble, high mechanical strength and elongation due its microstructure, ferrite and martensite. These properties are obtained by a intercritical heat treatment which facilitates the formation of a hardness metastable microstructure shaped plates of low carbon steels. The applicability of Dual Phase steel in the structure of vehicles is huge and its production is already on a commercial scale, so the study and development of this material implies lower cost in automobile manufacturing processes. The dual phase steels DP600 and DP780 underwent tensile, hardness and metallographic analysis to evaluate and comparing its properties. The results indicate that the DP780 steel has higher strength and hardness than the DP600 steel and its microstructure consists of martensite higher fraction which accounts for the higher resistance and hardness. However, the DP600 has higher conformability to DP780 steel

Caracterização do fator de intensidade de tensão em corpos trincados através do método dos elementos finitos

The industry generally has sought materials with high mechanical resistance, low density, thermal stability and corrosion resistance. In the aerospace industry, for example, the use of aluminum alloys, such as Al 2024-T351 and Al 7075-T7351, have become essential. However, the use of these materials often do not resulted in a satisfactory performance of the component, since the presence of cracks can cause total rupture of the component, even with a tension below the yield stress of the material, unexpectedly. In this work, these aluminum alloys were analyzed and samples were modeled by the finite element method. Moreover, in the models were applied two different types of cracks, central and edge crack, a vertical force was applied to result in a tension 70% of the yield stress of the material analyzed. Through stress asymptotic distribution in the region near the crack tip were calculated the values of the stress intensity factors for each crack length, after the stress intensity factors characterized were compared graphically with the values of fracture toughness found in the available literature

Ensaios laboratoriais para a determinação da resistência de conexão entre geogrelhas de PVA e blocos segmentais

During the retaining wall project in soil reinforced with geogrids and face milling system for segmental blocks is essential to determine the maximum connection resistance between the block and the geogrid. Thus, the aim of this study was to analyze the connection resistance based on ASTM D- 6638-01 between the segmental block model MW of Muros Terrae® company with the geogrids model Fortrac® M 35 / 20x20, Fortrac® M 55 / 30x20, Fortrac® M 80 / 30x20 and Fortrac® M 110 / 30x20 of HUESKER Synthetic GmbH using gravel 1 as a filling material. As a result, the resistance curves were obtained for the four models of geogrids and was described how it fracture. An additional investigation was the average gain connection resistance percentage when it is applied to geogrid a second layer instead of a single layer. The average percentage gains in the connection resistance to the geogrids model Fortrac® M 35 / 20x20, Fortrac® M 55 / 30x20, Fortrac® M 80 / 30x20 and Fortrac® M 110 / 30x20 were, respectively, 63.20 %, 63, 47%, 62.23 % and 51.34 %. Finally, we made a comparative analysis of the results of this study with those obtained by Guimarães (2006), Urashima et. al (2008) and Almeida and Toma (2011) to evaluate which combinations offered higher connection resistance

Usinabilidade do aço DIN C45 trefilado de alta resistência

Pós-graduação em Engenharia Mecânica - FEG

Resistência à flexão em porcelana feldspática: efeito da ciclagem mecânica e limite de fadiga pelo método escada

This study evaluated the fatigue limit (FL) by the staircase method and the effect of mechanical cycling on the flexural strength (FS) of Duceragold feldspathic porcelain. Specimens (25 x 5 x 2 mm) were made according to manufacturer’s directions and submitted to three-point flexural strength test (n = 10). To determine FL (n = 30; 10,000 cycles; 2 Hz), an initial loading of 60% of the FS and an incremental loading (step) of 3% of the FS were used. Data were analyzed by Anova and Tukey´s test (p < 0.05). Although the proposed cycles have not reduced FS significantly, fractography analysis showed striation, characteristic signs of mechanical fatigue.

Resistência à tração diametral de cimentos de ionômero de vidro submetidos à aplicação de ondas de ultrassom

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Influência do tratamento superficial 3IP na vida em fadiga dos aços ABNT 4340 e 15-5PH para aplicação aeronáutica

Pós-graduação em Engenharia Mecânica - FEG

Efeito de elementos susbstitucionais e intersticiais nas propriedades mecânicas e na biocompatibilidade de ligas do sistema Ti-15Zr-xMo

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento e validação de um novo protocolo para ciclagem térmica de materiais dentários

Pós-graduação em Odontologia Restauradora - ICT

Abordagens estatísticas em testes de resistência de união entre dentina bovina, sistema adesivo e resina composta

Pós-graduação em Odontologia Restauradora - ICT

Efeito de nanofilmes depositados a plasma na resistência de união de um cimento resinoso a uma cerâmica à base de zircônia

Pós-graduação em Odontologia Restauradora - ICT

Caracterização microestrutural e crescimento subcrítico de trincas em cerâmicas odontológicas

Pós-graduação em Odontologia Restauradora - ICT

Sistema adesivo universal: influência da técnica de condicionamento e da pressão pulpar com soro fetal bovino ou água deionizada na resistência de união à dentina humana

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da resistência à fratura de próteses fixas temporárias reforçadas por uma malha experimental

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito da água ozonizada e gluconato de clorexidina sobre propriedades mecânicas e microbiológicas de materiais utilizados para confecção de próteses odontológicas

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)