Influence of selenization pressure on the growth of Cu2ZnSnSe4 films from stacked metallic layers

Cu2ZnSnSe4 (CZTSe) is a p-type semiconductor with a high absorption coefficient, 104 to 105 cm-1, and is being seen as a possible replacement for Cu(In,Ga)Se2 in thin film solar cells. Yet, there are some fundamental properties of CZTSe that are not well known, one of them is its band gap. In order to resolve its correct value it is necessary to improve the growth conditions to ensure that single phase crystalline thin films are obtained. One of the problems encountered when growing CZTSe is the loss of Sn through evaporation of SnSe. Stoichiometric films are then difficult to obtain and usually there are other phases present. One possible way to overcome this problem is to increase the pressure of growth of CZTSe. This can be done by introducing an atmosphere of an inert gas like Ar or N2. In this work we report the results of morphological, structural and optical studies of the properties of CZTSe thin films grown by selenization of DC magnetron sputtered metallic layers under different Ar pressures. The films are analysed by SEM/EDS, Raman scattering and XRD.

Study of optical and structural properties of Cu2ZnSnS4 thin films

Cu2ZnSnS4 is a promising semiconductor to be used as absorber in thin film solar cells. In this work, we investigated optical and structural properties of Cu2ZnSnS4 thin films grown by sulphurization of metallic precursors deposited on soda lime glass substrates. The crystalline phases were studied by X-ray diffraction measurements showing the presence of only the Cu2ZnSnS4 phase. The studied films were copper poor and zinc rich as shown by inductively coupled plasma mass spectroscopy. Scanning electron microscopy revealed a good crystallinity and compactness. An absorption coefficient varying between 3 and 4×104cm−1 was measured in the energy range between 1.75 and 3.5 eV. The band gap energy was estimated in 1.51 eV. Photoluminescence spectroscopy showed an asymmetric broad band emission. The dependence of this emission on the excitation power and temperature was investigated and compared to the predictions of the donor-acceptor-type transitions and radiative recombinations in the model of potential fluctuations. Experimental evidence was found to ascribe the observed emission to radiative transitions involving tail states created by potential fluctuations.

Estudo Estratigráfico e Paleontológico do Jurássico do Algarve Ocidental

Algarve Province, Southern Portugal, corresponds in part to a meso-cenozoic basin running along the coast from Cabo S. Vicente to beyond Spanish border. Structurally it is a big monocline plunging southwards much deformed mainly by two East-West longitudinal flexures. Lithostratigraphical and chronostratigraphical studies dealt specially with Jurassic formations. This and the geological mapping of the post-Hercynian sedimentary formations allow us to define the following units: Triassic-Lower Liassic Arenitos de Silves (Silves sandstones sensu P. Choffat, pro parte) - At their base the Silves sandstones (0-150m) are represented mainly by cross-bedded red sandstones. This unit is Upper Triassic (Keuper) in age, on the evidence of some Brachiopoda. Complexo margo-carbonatado de Silves (Silves marl-limestone complex=Silves sandstones sensu P. Choffat, pro parte) (80-200m) overlies the preceding, it may be reported to the Upper Triassic-Hettangian. It consists of a thick pelite-marl-dolomite-limestone series with many intercalations of greenstones. Since no fossils were found it is not possible to conclude whether it is still Hettangian or if it does correspond, in the whole or in part, already to the Sinemurian. Liassic Dolomitos e calcários dolomíticos de Espiche (Espiche dolomite-rocks and dolomitic-limestones) - The usually massive and finely crystalline or saccharoidal dolomites and dolomitic-limestones are the toughest strata of the Algarve margin giving rise to several hills. Its thickness attains in certain points 60 metres at least. Based on geometry and on lithological similarities with the carbonated complex of the northern basin of Tagus river (Peniche, São Pedro de Muel, Quiaios), this formation can be accepted as Sinemurian in age. As it happens with the carbonated complex, here also the first dolomite beds are non-isochronal throughout the region; upper time-limit of the dolomitic facies is either Lower Carixian, Lower Toarcian or even Lower Dogger. The dolomitization is secondary but not much later than sedimentation. However, between Cabo S. Vicente-Vila do Bispo there is evidence of an even later secondary dolomitization related to the regional fault complex. Calcário dolomítico com nódulos de silex da praia de Belixe (Belixe beach dolomitic-limestone with silex nodules) (50-55m) - Ascribed to Lower or Middle Carixian on the basis of Platypleuroceras sp., Metaderoceras sp. nov. and M. gr. Venarense. Calcário cristalino compacto com Protogrammoceras, Fuciniceras e ? Argutarpites de Belixe (Belixe compact crystalline limestone with Protogrammoceras, Fuciniceras and ? Argutarpites) (30m) - Ascribed to Lower Domerian. Middle and Upper Domerian are indicated but by a single specimen of ? Argutarpites. Calcários margosos e margas com Dactylioceras semicelatum e Harpoceratídeos de Armação Nova (Armação Nova marly limestones and marls with D. semicelatum and Harpoceratidae) (25m) -Ascribed to Lower Toarcian. Middle and Upper Toarcian formations are not known in the Algarve. Dogger Calcários oolíticos, c. corálicos, c. pisolíticos, c. calciclásticos, c. dolomíticos e dolomitos de Almadena (Almadena oolitic-limestones, coral-reef-limestones, pisolite-limestones, limeclastic-limestones, dolomitic-limestones and dolomite-rocks) (more than 50 metres), with lagoonal facies. Ascribed to Aalenian-Bathonian-? Callovian. Margas acinzentadas e calcários detríticos com Zoophycos da praia de Mareta (Mareta beach greyish marls and detritical limestones with Zoophycos) (40m) - Pelagic transreef facies with Upper Bajocian and Bathonian ammonites. Calcários margosos e margas da praia de Mareta (Mareta beach pelagic marly-limestones and marls) (110m) - Ascribed to the Callovian on its ammonites. Malm Near Cabo S. Vicente and Sagres the first Upper Jurassic level consists of a yellowish-brown nodular, compact, locally phosphated and ferruginous, sometimes conglomeratic, marly limestone (0,35-1,50m) containing a rich macrofauna, which includes: 1) Callovian forms unknown at Lower Oxfordian; 2) Upper Callovian forms that still survived in Lower and Middle Oxfordian; 3) Lower Oxfordian forms (Mariae and Cordatum Zones); 4) Lower and Middle Oxfordian forms (Mariae to Plicatilis Zone); 5) Middle Oxfordian forms (plicatilis Zone), and some ones appearing in Middle Oxfordian. This condensed deposit is therefore dated from Middle Oxfordian (Plicatilis Zone). The other Upper Jurassic lithostratigraphical units were also mapped but their detailed study is not presented in this work. Correlations between lithostratigraphical and chronostratigraphical scales from P. Choffat, J. Pratsch, C. Palain and from the author are stated. Further correlations are attempted between zonc scales of Carixian-Lower Toarcian and Upper Bajocian-Middle Oxfordian of France, Spain (Asturias, Iberian and Betic Chains), Argel (Orania) and Portugal (northern Tagus basin and Algarve). The study of pyritous fossil assemblages common in Upper Bathonian-Lower Callovian marly levels of the praia da Mareta seems to suggest that these sediments were deposited in a bay or in an almost closed coastal re-entrance virtually without deep water circulation. Although such conditions may occur at any depth one may suppose that these ones actually correspond to an infralittoral neritic environment. The thaphocoenosis collected there are almost entirely composed of nektonic (ammonites, Belemnites) and planktonic (Bositra) faunas. The sedentary (crinoids, brachiopods) or free (sea-urchins, gastropods) epibenthonic forms are very scarce; endobenthonic forms are not known. The palaeontological study of all Nautiloids and Ammonoids of the Liassic and Dogger is presented (except Kosmoceratidae and Perisphinctaceae). Among the thirty one taxa dealt with, one is new (Metaderoceras sp. nov.) and the great majority of the others has been identified for the first time in Algarve. Some others have never been reported before in Portuguese formations. The evolution, during Jurassic times, of the sedimentary basins of the Portuguese plate margin is described. The absence of Cephalopods in the very extensive marly and dolomitic limestones, partly marine, suggests that, during Lower Liassic, palaeogeography underwent no great changes. Dolomitic-limestone with silex nodules from Cabo S. Vicente contain the first ammonites recorded at the base of the Middle Liassic. This facies, although very common in Tethys, is unknown north of the Tagus. The faunal assemblage has a mediterranean to submediterranean character. Comparisons between faunal assemblage" from Algarve with the ones known north of the Tagus show that communications between Boreal Europe and Tethys, virtually non-existent during Lower and Middle Carixian, became very easy during Lower Domerian. In earlier Pliensbachian times two distinct seas were adjacent to the Iberian plate. One, an epicontinental sea with a tethyan fauna, extended southwards from the Meseta margin. Another, was a boreal sea; during its transgressive episodes boreal faunas attained into the basin north of the Tagus. During Middle Carixian and Lower Domerian, owing to simultaneous transgressions, these two seas joined together allowing faunal exchanges along the epicontinental areas which limited the emerging hercynian chains belts. During Liassic, the Algarve belonged undoubtedly to the tethyan submediterranean province. The area north of the Tagus, on the contrary, was a complex realm where subboreal and tethyan affinities alternatively prevailed. In the Algarve the first Middle Jurassic deposits do frequently show lateral thickness reductions as well as unconformities contemporaneous with other generalized disturbances on the sedimentation processes in other parts of Europe. By this time, near Sagres, a barrier reef developed separating lagoonal or ante-reef facies from the transreef pelagic zone. The presence of tethyan fauna, the abundance of Phylloceratidae and the absence of boreal forms allow us to consider the Algarve basin as a submediterranean province. The presence of Callovian pelagic fossiliferous formations in the Loulé area shows that during Middle Jurassic the marl-limestone transreef sedimentation was not confined to the western Algarve. They would extend eastwards where they only can be seen in the core of some anticlines. This is due to the progressive sinking of the meso-cenozoic formations as we proceed towards the South of the Sagres-Algoz-Querença flexure. In the whole of the Peninsule, and as for the Middle Callovian, an important regression can be clearly recognized on the evidence of an erosion surface which strikes obliquely the Middle and Upper Callovian strata. The geographic boundaries of the different faunal provinces are not changed by the presence of many Kosmoceratidae in the phosphate nodules since they are but a minority in comparison with the tethyan forms. An abstract model can be constructed showing that in Western Europe the Kosmoceratidae may have migrated South and westwards through a channel of the sea that linked Paris basin to Poitou and Aquitaine. By migrating between the Iberian meseta and the Armorican massif this fauna reached northern Tagus basin at the beginning of Upper Callovian (Athleta Zone); this south and southwest bound migration would have proceeded, allowing such forms to reach Algarve basin only in latest Callovian times (Lamberti Zone). This migration means that during Middle Jurassic a widely spread North Atlantic sea would exist, flooding the western part of Portugal up to the Poitou.

Electrodeposition and characterization of nikel-copper metallic foams for application as electrodes for supercapacitors

Nickel-copper metallic foams were electrodeposited from an acidic electrolyte, using hydrogen bubble evolution as a dynamic template. Their morphology and chemical composition was studied by scanning electron microscopy and related to the deposition parameters (applied current density and deposition time). For high currents densities (above 1 A cm(-2)) the nickel-copper deposits have a three-dimensional foam-like morphology with randomly distributed nearly-circular pores whose walls present an open dendritic structure. The nickel-copper foams are crystalline and composed of pure nickel and a copper-rich phase containing nickel in solid solution. The electrochemical behaviour of the material was studied by cyclic voltammetry and chronopotentiometry (charge-discharge curves) aiming at its application as a positive electrode for supercapacitors. Cyclic voltammograms showed that the Ni-Cu foams have a pseudocapacitive behaviour. The specific capacitance was calculated from charge-discharge data and the best value (105 F g(-1) at 1 mA cm(-2)) was obtained for nickel-copper foams deposited at 1.8 A cm(-2) for 180 s. Cycling stability of these foams was also assessed and they present a 90 % capacitance retention after 10,000 cycles at 10 mA cm(-2).

Surface morphology and phase transformations of femtosecond laser-processed saphire

The morphological and structural modifications induced in sapphire by surface treatment with femtosecond laser radiation were studied. Single-crystal sapphire wafers cut parallel to the (0 1 2) planes were treated with 560 fs, 1030 nm wavelength laser radiation using wide ranges of pulse energy and repetition rate. Self-ordered periodic structures with an average spatial periodicity of similar to 300 nm were observed for fluences slightly higher than the ablation threshold. For higher fluences the interaction was more disruptive and extensive fracture, exfoliation, and ejection of ablation debris occurred. Four types of particles were found in the ablation debris: (a) spherical nanoparticles about 50 nm in diameter; (b) composite particles between 150 and 400 nm in size; (c) rounded resolidified particles about 100-500 nm in size; and (d) angular particles presenting a lamellar structure and deformation twins. The study of those particles by selected area electron diffraction showed that the spherical nanoparticles and the composite particles are amorphous, while the resolidified droplets and the angular particles, present a crystalline a-alumina structure, the same of the original material. Taking into consideration the existing ablation theories, it is proposed that the spherical nanoparticles are directly emitted from the surface in the ablation plume, while resolidified droplets are emitted as a result of the ablation process, in the liquid phase, in the low intensity regime, and by exfoliation, in the high intensity regime. Nanoparticle clusters are formed by nanoparticle coalescence in the cooling ablation plume. (C) 2013 Elsevier B.V. All rights reserved.

Synthesis of Sub-5 NM Co-Doped SnO2 nanoparticles and their structural microstructural, optical and photocatalytic properties

A swift chemical route to synthesize Co-doped SnO2 nanopowders is described. Pure and highly stable Sn1-xCoxO2-delta (0 <= x <= 0.15) crystalline nanoparticles were synthesized, with mean grain sizes <5 nm and the dopant element homogeneously distributed in the SnO2 matrix. The UV-visible diffuse reflectance spectra of the Sn1-xCoxO2-delta samples reveal red shifts, the optical bandgap energies decreasing with increasing Co concentration. The samples' Urbach energies were calculated and correlated with their bandgap energies. The photocatalytic activity of the Sn1-xCoxO2-delta samples was investigated for the 4-hydroxylbenzoic acid (4-HBA) degradation process. A complete photodegradation of a 10 ppm 4-HBA solution was achieved using 0.02% (w/w) of Sn0.95Co0.05O2-delta nanoparticles in 60 min of irradiation. (C) 2014 Elsevier B.V. All rights reserved.

Synthesis of titanate nanostructures using amorphous precursor material and their adsorption/photocatalytic properties

This article reports on a new and swift hydrothermal chemical route to prepare titanate nanostructures (TNS) avoiding the use of crystalline TiO2 as starting material. The synthesis approach uses a commercial solution of TiCl3 as titanium source to prepare an amorphous precursor, circumventing the use of hazardous chemical compounds. The influence of the reaction temperature and dwell autoclave time on the structure and morphology of the synthesised materials was studied. Homogeneous titanate nanotubes with a high length/diameter aspect ratio were synthesised at 160 degrees C and 24 h. A band gap of 3.06 +/- 0.03 eV was determined for the TNS samples prepared in these experimental conditions. This value is red shifted by 0.14 eV compared to the band gap value usually reported for the TiO2 anatase. Moreover, such samples show better adsorption capacity and photocatalytic performance on the dye rhodamine 6G (R6G) photodegradation process than TiO2 nanoparticles. A 98% reduction of the R6G concentration was achieved after 45 min of irradiation of a 10 ppm dye aqueous solution and 1 g L-1 of TNS catalyst.

High-performance flexible hybrid field-effect transistors based on cellulose fiber paper

IEEE Electron Device Letters, VOL. 29, NO. 9,

Volcanic events in the Eastern part of the Adriatic foreland (Northern Marchean Italy)

Proceedings of the 1'I R.C.A.N.S. Congress, Lisboa, October 1992

A cellulosic liquid crystal pool for cellulose nanocrystals: structure and molecular dynamics at high shear rates

Cellulose and its derivatives, such as hydroxypropylcellulose (HPC) have been studied for a long time but they are still not well understood particularly in liquid crystalline solutions. These systems can be at the origin of networks with properties similar to liquid crystalline (LC) elastomers. The films produced from LC solutions can be manipulated by the action of moisture allowing for instance the development of a soft motor (Geng et al., 2013) driven by humidity. Cellulose nanocrystals (CNC), which combine cellulose properties with the specific characteristics of nanoscale materials, have been mainly studied for their potential as a reinforcing agent. Suspensions of CNC can also self-order originating a liquid-crystalline chiral nematic phases. Considering the liquid crystalline features that both LC-HPC and CNC can acquire, we prepared LC-HPC/CNC solutions with different CNC contents (1,2 and 5 wt.%). The effect of the CNC into the LC-HPC matrix was determined by coupling rheology and NMR spectroscopy - Rheo-NMR a technique tailored to analyse orientational order in sheared systems. (C) 2015 Elsevier Ltd. All rights reserved.

Influence of the substrate on structure and magnetic properties of Co-N thin films

Cubic cobalt nitride films were grown onto different single crystalline substrates Al2O3 (0 0 0 1) and (1 1 View the MathML source 0), MgO (1 0 0) and (1 1 0) and TiO2 (1 0 0) and (1 1 0). The films display low atomic densities compared with the bulk material, are ferromagnetic and have metallic electrical conductivity. X-ray diffraction and X-ray absorption fine structure confirm the cubic structure of the films and with RBS results indicate that samples are not homogeneous at the microscopic scale, coexisting Co4+xN nitride with nitrogen rich regions. The magnetization of the films decreases with increase of the nitrogen content, variation that is shown to be due to the decrease of the cobalt density, and not to a decrease of the magnetic moment per cobalt ion. The films are crystalline with a nitrogen deficient stoichiometry and epitaxial with orientation determined by the substrate.

Large-area homogeneous periodic surface structures generated on the surface sputtered boron carbide thin films by femtosecond laser processing

Amorphous and crystalline sputtered boron carbide thin films have a very high hardness even surpassing that of bulk crystalline boron carbide (≈41 GPa). However, magnetron sputtered B-C films have high friction coefficients (C.o.F) which limit their industrial application. Nanopatterning of materials surfaces has been proposed as a solution to decrease the C.o.F. The contact area of the nanopatterned surfaces is decreased due to the nanometre size of the asperities which results in a significant reduction of adhesion and friction. In the present work, the surface of amorphous and polycrystalline B-C thin films deposited by magnetron sputtering was nanopatterned using infrared femtosecond laser radiation. Successive parallel laser tracks 10 μm apart were overlapped in order to obtain a processed area of about 3 mm2. Sinusoidal-like undulations with the same spatial period as the laser tracks were formed on the surface of the amorphous boron carbide films after laser processing. The undulations amplitude increases with increasing laser fluence. The formation of undulations with a 10 μm period was also observed on the surface of the crystalline boron carbide film processed with a pulse energy of 72 μJ. The amplitude of the undulations is about 10 times higher than in the amorphous films processed at the same pulse energy due to the higher roughness of the films and consequent increase in laser radiation absorption. LIPSS formation on the surface of the films was achieved for the three B-C films under study. However, LIPSS are formed under different circumstances. Processing of the amorphous films at low fluence (72 μJ) results in LIPSS formation only on localized spots on the film surface. LIPSS formation was also observed on the top of the undulations formed after laser processing with 78 μJ of the amorphous film deposited at 800 °C. Finally, large-area homogeneous LIPSS coverage of the boron carbide crystalline films surface was achieved within a large range of laser fluences although holes are also formed at higher laser fluences.

Ambient noise tomography of the East African Rift in Mozambique

Seismic ambient noise tomography is applied to central and southern Mozambique, located in the tip of the East African Rift (EAR). The deployment of MOZART seismic network, with a total of 30 broad-band stations continuously recording for 26 months, allowed us to carry out the first tomographic study of the crust under this region, which until now remained largely unexplored at this scale. From cross-correlations extracted from coherent noise we obtained Rayleigh wave group velocity dispersion curves for the period range 5–40 s. These dispersion relations were inverted to produce group velocity maps, and 1-D shear wave velocity profiles at selected points. High group velocities are observed at all periods on the eastern edge of the Kaapvaal and Zimbabwe cratons, in agreement with the findings of previous studies. Further east, a pronounced slow anomaly is observed in central and southern Mozambique, where the rifting between southern Africa and Antarctica created a passive margin in the Mesozoic, and further rifting is currently happening as a result of the southward propagation of the EAR. In this study, we also addressed the question concerning the nature of the crust (continental versus oceanic) in the Mozambique Coastal Plains (MCP), still in debate. Our data do not support previous suggestions that the MCP are floored by oceanic crust since a shallow Moho could not be detected, and we discuss an alternative explanation for its ocean-like magnetic signature. Our velocity maps suggest that the crystalline basement of the Zimbabwe craton may extend further east well into Mozambique underneath the sediment cover, contrary to what is usually assumed, while further south the Kaapval craton passes into slow rifted crust at the Lebombo monocline as expected. The sharp passage from fast crust to slow crust on the northern part of the study area coincides with the seismically active NNE-SSW Urema rift, while further south the Mazenga graben adopts an N-S direction parallel to the eastern limit of the Kaapvaal craton. We conclude that these two extensional structures herald the southward continuation of the EAR, and infer a structural control of the transition between the two types of crust on the ongoing deformation.

Development of electrospun Ion jelly fibers® for drug delivery

Dissertação para obtenção do Grau de Mestre em Biotecnologia

Caracterização do feixe de radiação X num bloco operatório em cirurgia ortop

RESUMO - Na radiologia de intervenção, e concretamente em ortopedia, os raios X são intensamente utilizados permitindo a visualização de diversas técnicas de intervenção cirúrgica. Do ponto de vista médico as vantagens dessa prática são enormes, contudo, os profissionais de saúde envolvidos são susceptíveis de estarem expostos a valores de dose de radiação que significam a sua classificação como trabalhadores expostos. O presente estudo realizou-se num hospital e teve como objectivo obter uma estimativa das doses envolvidas em ortopedia de intervenção, utilizando várias metodologias experimentais para caracterização do campo de radiação primário e secundário. Observaram-se distintos níveis de dose de acordo com a zona anatómica exposta à radiação X: (i) gónadas — 0,02 a 3 mGy/h; (ii) cristalino — 0,06 a 1 mGy/h e (iii) mãos — 0,6 mGy/h. Tais resultados evidenciam uma clara necessidade de utilização de equipamentos de protecção e de vigilância dosimétrica pelos profissionais de saúde envolvidos no acto cirúrgico.--------------------------ABSTRACT - In intervention radiology, and more specifically in orthopaedics, X-rays are intensely used allowing the visualization of many acts of clinical intervention. From a clinical perspective, the advantages of that practice are significant; however, involved health care professionals are susceptible of being exposed to radiation dose values that mean their classification as exposed workers. The present study, performed in a hospital, aimed to obtain an estimation of the doses involved in intervention orthopaedics through several experimental methodologies in order to characterise the primary and the secondary radiation fields. Different levels of dose were observed according to the anatomic area exposed to X radiation: (i) gonads — 0.02 a 3 mGy/h; (ii) crystalline lens — 0.06 a 1 mGy/h e (iii) hands – 0.6 mGy/h. Such results denote a clear need of protection equipment use and of dosimetric surveillance by the health