Geochemistry and structural formulas of heavy minerals from sands and sandstones of ODP Leg 126 samples

Lower Oligocene to Pleistocene volcaniclastic sands and sandstones recovered around the Izu-Bonin Arc during Ocean Drilling Program Leg 126 were derived entirely from Izu-Bonin Arc volcanism. Individual grains consist of volcanic glass, pumice, scoria, basaltic or andesitic fragments, plagioclase, pyroxene, and minor olivine and hornblende. In Pliocene-Pleistocene samples plagioclase and heavy minerals in the volcaniclastic sands and sandstones are present in the following abundances: plagioclase > orthopyroxene > clinopyroxene > pigeonite > olivine. In contrast, plagioclase and heavy minerals found in Oligocene-Miocene samples occur in the following order: plagioclase > clinopyroxene > orthopyroxene > hornblende. The low concentration of Al, Ti, and Cr in calcium-rich clinopyroxenes in Oligocene to Holocene sediments suggests that the sources of the volcaniclastic detritus were nonalkalic igneous rocks. There are, however, some distinctive differences in the chemical composition of pyroxene between the Pliocene-Pleistocene and Oligocene-Miocene volcaniclastic sands and sandstones. Orthopyroxene belongs to the hypersthene-ferrohypersthene series (Fe-rich) in Pliocene-Pleistocene sediments, and the bronzitehypersthene series (Mg-rich) in Oligocene-Miocene sediments. Clinopyroxene is characterized by augite and pigeonite in Pliocene-Pleistocene sediments, and by the diopside-augite series in Oligocene-Miocene sediments. Mineral assemblages and mineral chemistry of the volcaniclastic sands and sandstones reflect those of the volcanic source rocks. Therefore, the observed changes in mineralogy record the historical change in volcanism of the Izu-Bonin Arc. The mineralogy is consistent with the geochemistry of the volcaniclastic sands and sandstones and the geochemistry of forearc volcanic rocks of the Izu-Bonin Arc since the Oligocene.

Physical properties and elastic constants of ODP Holes 137-504B and 140-504B upper crustal rocks

Seismic velocities have been measured at confining pressures of 100 MPa and 600 MPa for sheeted dike samples recovered during Ocean Drilling Program Legs 137 and 140. The compressional- and shear-wave velocities show an increase with depth at Hole 504B, which is in sharp contrast to the atmospheric pressure velocity measurements performed as part of the shipboard analyses. Rocks exposed to different types of alteration and fracture patterns show distinct changes in their physical properties. The seismic reflectors observed on the vertical seismic profile (VSP) experiment performed during Leg 111 may have been caused by low velocity zones resulting from alteration. The amount of fracturing and hydrothermal alteration in several zones also may have contributed to the acoustic impedance contrast necessary to produce the E5 reflector. Poisson's ratios calculated from laboratory velocity measurements show several low values at depths ranging from 1600 mbsf to 2000 mbsf, which tends to follow similar trends obtained from previous oceanic refraction experiments. A comparison of physical properties between samples recovered from Hole 504B and ophiolite studies in the Bay of Islands and Oman shows a good correlation with the Bay of Islands but significant differences from the measurements performed in the Oman complex.

Organic geochemistry of ODP Leg 104 holes

The Leg 104 organic geochemistry program consisted of monitoring (a) hydrocarbon gases, (b) organic and inorganic carbon, and (c) parameters resulting from Rock-Eval pyrolysis at three sites on the Voring Plateau. The results amplify some of those obtained earlier on Deep Sea Drilling Project (DSDP) Leg 38. In a regional sense there is an inverse correlation between amounts of hydrocarbon gas and organic carbon. For example, significant concentrations of methane are present only at Site 644 in the inner part of the plateau where organic carbon contents are always less than 1%; in contrast, at Site 642 on the outer plateau, methane concentrations are very low (ppm range) whereas amounts of organic carbon approach 2%. Only at Site 644 are the environmental conditions such that methanogenesis is an active diagenetic process. Because of the importance of routine gas analyses to the Ocean Drilling Program (ODP), a procedure was devised to improve the use of Vacutainers for collection of gas samples. Comparison of methods for determining organic carbon showed that at Sites 643 and 644 Rock-Eval TOC could be used as a measure of organic carbon, but not at Site 642. Although no liquid or solid hydrocarbons were encountered at any of the sites, a catalog of potential organic geochemical contaminants was developed in anticipation of such a discovery.

Susana Zanetti y otros, Las cenizas de la huella. Linajes y figuras de artista en torno al modernismo. Rosario, Beatriz Viterbo Editora, 1997, 126 págs.

Fil: Basile, María Teresa Gabriela. Universidad Nacional de La Plata. Facultad de Humanidades y Ciencias de la Educación; Argentina.

Mechanical behavior of ODP Hole 137-504B basalts

Core samples of basalt collected from Hole 504B during Leg 137 were investigated regarding their mechanical behavior. The rock samples were measured for hardness, compression strength, and modulus of elasticity. Abrasion loss of weight and Shore sclerometer methods were used for determining hardness. Static and dynamic methods were used for calculating modulus of elasticity. Test results were compared with shipboard measurements of ultrasonic velocity and dry-bulk density. Test results were interpreted statistically to provide data not only on mechanical behavior changes of the rock but also on the precision of the methods used.