Efeito de adições poliméricas na aderência de pastas de cimento a tubos metálicos após ciclagem térmica

Thermal recovery methods, especially steam injection, have been used to produce heavy oils. However, these methods imply that the metallic casing-cement sheath interface is submitted to thermal cycling. As a consequence, cracking may develop due to the thermal expansion mismatch of such materials, which allows the flow of oil and gas through the cement sheath, with environmental and economical consequences. It is therefore important to anticipate interfacial discontinuities that may arise upon Thermal recovery. The present study reports a simple alternative method to measure the shear strength of casing-sheath interfaces using pushthrough geometry, applied to polymer-containing hardened cement slurries. Polyurethane and recycled tire rubber were added to Portland-bases slurries to improve the fracture energy of intrinsically brittle cement. Samples consisting of metallic casing sections surrounded by hardened polymer-cement composites were prepared and mechanically tested. The effect of thermal cycles was investigated to simulate temperature conditions encountered in steam injection recovery. The results showed that the addition of polyurethane significantly improved the shear strength of the casing-sheath interface. The strength values obtained adding 10% BWOC of polyurethane to a Portland-base slurry more than doubled with respect to that of polyurethane-free slurries. Therefore, the use of polyurethane significantly contributes to reduce the damage caused by thermal cycling to cement sheath, improving the safety conditions of oil wells and the recovery of heavy oils

Qualidade fisiológica de sementes de milho-doce BR 400 (bt) em função do teor de água na colheita e da temperatura de secagem

O objetivo deste estudo foi avaliar a qualidade fisiológica das sementes de milho-doce em função do teor de água na colheita e da temperatura de secagem em espiga. O experimento foi instalado na área experimental da FCA/Unesp, Botucatu-SP. Utilizou-se a cultivar BR 400 (bt) 'Super doce'. O delineamento experimental empregado foi o de blocos ao acaso com seis repetições, constituindo os tratamentos as épocas de colheitas. As colheitas das espigas foram iniciadas após a maturidade fisiológica; após despalhadas e divididas em duas porções, as espigas foram submetidas a secagem em estufas com circulação forçada nas temperaturas de 30 e 40ºC. Foi utilizada uma testemunha com sementes secadas no campo com 10,1% de teor de água. Foram determinados os teores de água das sementes, inicial e após a secagem, de todas as colheitas. Após a secagem, as espigas foram debulhadas manualmente, as sementes acondicionadas em saco de papel e armazenadas em condições ambientais de laboratório. As avaliações da qualidade fisiológica das sementes (emergência de plântulas no campo, índice de velocidade de emergência, matéria seca de plântulas, germinação, vigor-primeira contagem do teste de germinação, envelhecimento acelerado, teste de frio, condutividade elétrica e teores de Ca, Mg, K e Na lixiviados na solução do teste de condutividade elétrica) foram realizadas antes e após seis meses de armazenamento. As sementes de milho-doce cultivar BR 400 (bt), com teor de água igual ou menor do que 35%, podem ser submetidas à secagem em espiga a temperatura de 30 ou 40ºC, sem perdas significativas em sua qualidade fisiológica.

Thermoplastic starch/natural rubber blends

Thermoplastic starch/natural rubber polymer blends were prepared using directly natural latex and cornstarch. The blends were prepared in an intensive batch mixer at 150 degreesC, with natural rubber content varying from 2.5 to 20%. The blends were characterised by mechanical analysis (stress-strain) and by scanning electron microscopy. The results revealed a reduction in the modulus and in tensile strength, becoming the blends less brittle than thermoplastic starch alone. Phase separation was observed in some compositions and was dependent on rubber and on plasticiser content (glycerol). Increasing plasticiser content made possible the addition of higher amounts of rubber. The addition of rubber was, however, limited by phase separation the appearance of which depended on the glycerol content. Scanning electron microscopy showed a good dispersion of the natural rubber in the continuos phase of thermoplastic starch matrix. (C) 2003 Elsevier B.V. Ltd. All rights reserved.

Avaliação do desgaste abrasivo causado pelas cerâmicas Duceram e Vita em resinas compostas pelo método do disco retificado

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Improvement in the fatigue strength of chromium electroplated AISI 4340 steel by shot peening

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Flexural Test on Recycled Polystyrene

In socio-environmental scenario increased the nature resources concern beyond products and subproducts reuse. Recycling is the approach for a material or energy reintroducing in productive system. This method allows the reduction of garbage volume dumped in environment, saving energy and decreasing the requirement of natural resources use. In general, the ending of expanded polystyrene is deposited sanitary landfills or garbage dumps without control that take large volume and spreads easily by aeolian action, with consequently environmental pollution, however, the recycling avoids their misuse and the obtainment from petroleum is reduced. This work recycled expanded polystyrene via merger and/or dissolution by solvents for the production of integrated circuits boards. The obtained material was characterized in flexural mode according to ASTM D 790 and results were compared with phenolite, traditionally used. Specimens fractures were observed by electronic microscopy scanning in order to establish patterns. Expanded Polyestirene recycled as well as phenolite were also thermo analyzed by TGA and DSC. The method using dissolution produced very brittle materials. The method using merger showed no voids formation nor increased the brittleness of the material. The recycled polystyrene presented a strength value significantly lower than that for the phenolite. (C) 2011 Published by Elsevier Ltd. Selection and peer-review under responsibility of ICM11

Condicionamento estrutural das zonasa de cisalhamento da região de Forquilha, domínio Ceará Central: uma abordagem integrada de sensoriamento remoto e geologia estrutural

The studied region, named Forquilha and localized in northwestern Central Ceará domain (northern portion of Borborema Province), presents a lithostratigraphic framework constituted by paleoproterozoic metaplutonics, metasedimentary sequences and neoproterozoic granitoids. The metasedimentary rocks of Ceará group occupy most part of the area. This group is subdivided in two distinct units: Canindé and Independência. Canindé unit is represented basically by biotite paragneisses and muscovite paragneisses, with minor metabasic rocks (amphibolite lens). Independência sequence is composed by garnetiferous paragneisses, sillimanite-garnet-quartz-muscovite schists and quartz-muscovite schists, pure or muscovite quartzites and rare marbles. At least three ductile deformation events were recognized in both units of Ceará group, named D1, D2 and D3. The former one is interpreted as related to a low angle tangential tectonics which mass transport is southward. D2 event is marked by the development of close/isoclinal folds with a N-S oriented axis. Refolding patterns generated by F1 and F2 superposition are found in several places. The latest event (D3) corresponds to a transcurrent tectonics, which led to development of mega-folds and several shear zones, under a transpressional regime. The mapped shear zones are Humberto Monte (ZCHM), Poço Cercado (ZCPC) and Forquilha (ZCF). Digital image processing of enhanced Landsat 7-ETM+ satellite images, combined with field data, demonstrate that these penetrative structures are associated with positive and negative geomorphologic patterns, distributed in linear and curvilinear arrangements with tonal banding, corresponding to the ductile fabric and to crests. Diverse color composites were tested and RGB-531 and RGB-752 provided the best results for lineament analysis of the most prominent shear zones. Spatial filtering techniques (3x3 and 5x5 filters) were also used and the application of Prewitt filters generated the best products. The integrated analysis of morphological and textural aspects from filtered images, variation of tonalities related to the distribution of geologic units in color composites and the superposition over a digital elevation model, contributed to a characterization of the structural framework of the study area. Kinematic compatibility of ZCHM, ZCPC, ZCF shear zones, as well as Sobral-Pedro II (ZCSPII) shear zone, situated to the west of the study area, was one of the goal of this work. Two of these shear zones (ZCHM, ZCPC) display sinistral movements, while the others (ZCSPII, ZCF) exhibit dextral kinematics. 40Ar/39Ar ages obtained in this thesis for ZCSPII and ZCPC, associated with other 40Ar/39Ar data of adjacent areas, indicate that all these shear zones are related to Brasiliano orogeny. The trend of the structures, the opposite shear senses and the similar metamorphic conditions are fitted in a model based on the development of conjugate shear zones in an unconfined transpression area. A WNW-ESE bulk shortening direction is infered. The geometry and kinematic of the studied structures suggest that shortening was largely accommodated by lateral extrusion, with only minor amounts of vertical stretch

A história do intemperismo na Província Borborema Oriental, Nordeste do Brasil: implicações paleoclimáticas e tectônicas

Until some years ago, weathering geochronology was primarily based on the K-Ar and 40Ar/39Ar dating of supergene minerals. Recent advances in the analysis of supergene goethite by the (U-Th)/He method expanded the number of suitable minerals for such purpose, as well as the time of application for weathering geochronology. This study represents the first systematic approach in Brazil, combining both the 40Ar/39Ar e (U-Th)/He methodologies to improve the knowledge on the weathering and the age of nonfossiliferous sediments. Supported by geologic and geomorphologic correlations, we identified different types of weathering profiles occurring in the interior and coastal areas of northeastern Brazil. These profiles were correlated to main regional geomorphological domains: the Borborema Plateau , the Sertaneja Depression , and the Coastal Cuestas and Plains, and respective planation surfaces, which study is fundamental to understand the landscape evolution of the northern portion of the eastern Borborema Province. The depth and stratigraphic organization of the weathering profiles in each of the geomorphological domains permitted to establish that: (i) the profiles on the highlands that cap the Borborema Surface are deeper (up to 100 m) and can be considered as typical lateritic profiles; (ii) on the lowlands that form the Sertaneja Surface , the weathering profiles are shallow and poorly developed (2-5 m deep); (iii) the profiles along the coastal area are moderately developed (up to 25 m deep), and are characterized by thick saprolites and mottle zones. Aiming to establish the timing of the evolution of northeastern Brazil, we studied 29 weathering profiles representing distinct topographic levels of the Borborema Province, from the highlands to the coast, through the analysis of 248 grains of supergene manganese oxides using laser step-heating 40Ar/39Ar geochronology. Additionally, we applied the (U-Th)/He method in 20 weathering profiles, by dating 171 grains of supergene iron oxides and hydroxides. Geochronological results for 248 grains of manganese oxides analyzed by the 40Ar/39Ar method indicate that the weathering profiles in the study area record the history of weathering from the Oligocene to the Pleistocene, with ages in the order of 31.4 ± 1.0 Ma to 0.8 ± 0.4 Ma. Dating of 171 grains of goethite by the (U-Th)/He method yielded ages ranging from 43.2 ± 4.3 Ma to 0.8 ± 0.1 Ma, suggesting the weathering processes last from the Eocene to the Pleistocene. The precipitation of supergene goethite in this interval confirms the age of the weathering processes identified from the manganese oxides record. 105 goethite grains from 8 different occurrences of the Barreiras Formation were dated by the (U-Th)/He method. Five grains collected from the cement in the Barreiras Formation sandstones, in the Lagoa Salgada and Rio do Fogo coastal cuestas, yielded ages of 17.6 ± 1.8 Ma, 17.3 ± 1.7 Ma, 16.3 ± 1.6 Ma, 16.2 ± 1.6 Ma and 13.6 ± 1.4 Ma. Results of 69 goethite grains from authigenic pisoliths collected in 7 different localities also yielded concordant ages, varying from 17.8 ± 1.8 to 7.5 ± 0.8 Ma. Results obtained from 31 detrital grains are concordant in 3 distinct localities (Lagoa Salgada, Praia da Garças e Ponta Grossa); they vary in the range of 43.2 ± 4.3 to 21.6 ± 2.2 Ma, and indicate that the maximum age for the Barreiras Formation deposition is around 22 Ma. 40Ar/39Ar results for 15 manganese oxides grains associated with the Barreiras Formation weathering profiles, in 3 different localities, vary from 13.1 ± 0.9 to 7.7 ± 0.4 Ma, in the same range of ages obtained by the (U-Th)/He method. The systematic application of the 40Ar/39Ar and (U-Th)/He methods, respectively for manganese oxides and goethites, show that the Barreiras Formation sediments were already deposited since ca. 17 Ma, and that the weathering processes were active until ca. 7 Ma ago. The ages obtained from manganese oxides collected in the Cenozoic basalts (Macau Formation) also reveal a weathering history between 19 and 7 Ma, pointing to hot and humid conditions during most of the Miocene. 40Ar/39Ar ages yielded by manganese oxides associated with the Serra do Martins Formation vary from 14.1 ± 0.4 to 10.5 ± 0.3 Ma. On the other hand, (U-Th)/He ages from iron oxides/hydroxides collected in the Serra do Martins Formation mesas vary from 20.0 ± 2.0 to 5.5 ± 0.6 Ma, indicating that those sediments are older than 20 Ma. 40Ar/39Ar and (U-Th)/He results produced in this study are in agreement with paleoclimatic interpretations based on stable isotopes and clay index values measured in the Atlantic Ocean sediments, validating the use of weathering geochronology to investigate paleoclimatic variations. The direct dating of the Barreiras Formation permitted, for the first time, confident inferences on the age of the brittle deformation recorded by this sedimentary unit in the Rio Grande do Norte and Ceará states. The first event, syn-deposition, occurred during the early Miocene; an younger event, related to the post-depositional deformation of the Barreiras Formation, is associated with tectonic activity from the very early Miocene to the Holocene. In agreement with data from other areas, results obtained in this study reveal that the depth and complexity of the weathering profiles reflect the time of exposition of such areas to the weathering agents close to the surface. However, there is no clear relationship between ages vs. altitude. The depth and the stratigraphic organization of weathering profiles in northeastern Brazil, contrary to the southeastern Brazil pattern, do not vary toward the coast. In our study area, field observations reveal the presence of ancient, thick and complex lateritic profiles preserved in the sedimentary mesas on the Borborema Plateau, as younger, narrow and incipient ones occur in the dissected areas. Geochronological results obtained for these profiles yielded older ages on the high altitudes, and younger ages in the lowlands, suggesting the scarp retreatment is the most reliable model to explain the regional landscape evolution. However, in the coastal lowlands, the relatively older ages obtained indicate that more complexes processes were involved in the modeling of the local relief

Caracterização tectono-estratigráfica da sequência transicional na sub-bacia de Sergipe

This thesis deals with the tectonic-stratigraphic evolution of the Transitional Sequence in the Sergipe Sub-basin (the southern segment of the Sergipe-Alagoas Basin, Northeast Brazil), deposited in the time interval of the upper Alagoas/Aptian stage. Sequence boundaries and higher order internal sequences were identified, as well as the structures that affect or control its deposition. This integrated approach aimed to characterize the geodynamic setting and processes active during deposition of the Transitional Sequence, and its relations with the evolutionary tectonic stages recognized in the East Brazilian Margin basins. This subject addresses more general questions discussed in the literature, regarding the evolution from the Rift to the Drift stages, the expression and significance of the breakup unconformity, the relationships between sedimentation and tectonics at extensional settings, as well as the control on subsidence processes during this time interval. The tectonic-stratigraphic analysis of the Transitional Sequence was based on seismic sections and well logs, distributed along the Sergipe Sub-basin (SBSE). Geoseismic sections and seismic facies analysis, stratigraphic profiles and sections, were compiled through the main structural blocks of this sub-basin. These products support the depositional and tectonic-stratigraphic evolutionary models built for this sequence. The structural analysis highlighted similarities in deformation styles and kinematics during deposition of the Rift and Transitional sequences, pointing to continuing lithospheric extensional processes along a NW trend (X strain axis) until the end of deposition of the latter sequence was finished by the end of late Aptian. The late stage of extension/rifting was marked by (i) continuous (or as pulses) fault activity along the basin, controling subsidence and creation of depositional space, thereby characterizing upper crustal thinning and (ii) sagstyle deposition of the Transitional Sequence at a larger scale, reflecting the ductile stretching and thinnning of lower and sub crustal layers combined with an increasing importance of the thermal subsidence regime. Besides the late increments of rift tectonics, the Transitional Sequence is also affected by reactivation of the border faults of SBSE, during and after deposition of the Riachuelo Formation (lower section of the Transgressive Marine Sequence, of Albian age). It is possible that this reactivation reflects (through stress propagation along the newlycreated continental margin) the rifting processes still active further north, between the Alagoas Sub-basin and the Pernambuco-Paraíba Basin. The evaporitic beds of the Transitional Sequence contributed to the development of post-rift structures related to halokinesis and the continental margin collapse, affecting strata of the overlying marine sequences during the Middle Albian to the Maastrichtian, or even the Paleogene time interval. The stratigraphic analysis evidenced 5 depositional sequences of higher order, whose vertical succession indicates an upward increase of the base level, marked by deposition of continental siliciclastic systems overlain by lagunar-evaporitic and restricted marine systems, indicating that the Transitional Sequence was deposited during relative increase of the eustatic sea level. At a 2nd order cycle, the Transitional Sequence may represent the initial deposition of a Transgressive Systems Tract, whose passage to a Marine Transgressive Sequence would also be marked by the drowning of the depositional systems. At a 3rd order cycle, the sequence boundary corresponds to a local unconformity that laterally grades to a widespread correlative conformity. This boundary surface corresponds to a breakup unconformity , being equivalent to the Pre-Albian Unconformity at the SBSE and contrasting with the outstanding Pre-upper Alagoas Unconformity at the base of the Transitional Sequence; the latter is alternatively referred, in the literature, as the breakup unconformity. This Thesis supports the Pre-Albian Unconformity as marker of a major change in the (Rift-Drift) depositional and tectonic setting at SBSE, with equivalent but also diachronous boundary surfaces in other basins of the Atlantic margin. The Pre-upper Alagoas Unconformity developed due to astenosphere uplift (heating under high lithospheric extension rates) and post-dates the last major fault pulse and subsequent extensive block erosion. Later on, the number and net slip of active faults significantly decrease. At deep to ultra deep water basin segments, seaward-dipping reflectors (SDRs) are unconformably overlain by the seismic horizons correlated to the Transitional Sequence. The SDRs volcanic rocks overly (at least in part) continental crust and are tentatively ascribed to melting by adiabatic decompression of the rising astenospheric mantle. Even though being a major feature of SBSE (and possibly of other basins), the Pre-upper Alagoas Unconformity do not correspond to the end of lithospheric extension processes and beginning of seafloor spreading, as shown by the crustal-scale extensional structures that post-date the Transitional Sequence. Based on this whole context, deposition of the Transitional Sequence is better placed at a late interval of the Rift Stage, with the advance of an epicontinental sea over a crustal segment still undergoing extension. Along this segment, sedimentation was controled by a combination of thermal and mechanical subsidence. In continuation, the creation of oceanic lithosphere led to a decline in the mechanical subsidence component, extension was transferred to the mesoceanic ridge and the newly-formed continental margin (and the corresponding Marine Sequence) began to be controlled exclusively by the thermal subsidence component. Classical concepts, multidisciplinary data and new architectural and evolutionary crustal models can be reconciled and better understood under these lines

Evolução tectono-estrutural do Campo de Xaréu (Sub-bacia de Mundaú, Bacia do Ceará - NE do Brasil: abordagem multiescala e pluriferramental

The Xaréu Oil Field, located in the center-southern portion of the Mundaú Sub-Basin (eastern portion of the Ceará Basin), is characterized by a main Iramework of NW-trending and NE-dipping faults. The faults in the Xaréu Oil Field, among which the Xaréu Fautt stands out, are arranged according to an extensional-listriclan, rooted on a detachment surface corresponding to the Mundaú Fault, the border fautt of Mundaú Sub-Basin. During the tectonic-structural evolution of the Xaréu Oil Field and the Mundaú Sub-Basin, the Mundaú Fault played a crucial role on the control of the geometry of both compartments. The main carbonatic unit in the Xaréu Oil Field, named the Trairí Member(Paracuru Formation of Late Aptian to Early Albian age), contains the largest oil volume in the field, concentrated in structurally-controlled accumulations. The Trairí Member is composed by a variety of carbonatic rocks (massive, bedded or laminated calcilutites, ostracodites, calcarenites and carbonatic rudites, all of them presenting variable degrees of dolomitization). The carbonatic rocks are interbedded into thick packages of black shales and marls, besides local beds of siliciclastic conglomerates, sandstones, siltnes and argillites. From the spatial association and the genetic relationships between the carbonatic and siliciclastic units, it is possible to group them in three lithofacies associations (Marginal Plain, Ramp and Lacustrine Interior) that, together, were developed in a lacustrine system associated to a marginal sabkha. Structural studies based on drill coresthat sample the Trairí Member in the Xaréu Oil Field allowed to characterize two generations of meso- to microscale structures: the D1 group presents a typical hydroplastic character, being characterized by intra/interstratal to oblique-bedding shear zones. The hydroplastic character related to these structures allowed to infer their development at an early-lithilication stage of the Trairí Member, leading to infer an Early Cretaceous age to them. The second group of structures identified in the drill cores, nominated D2 and ascribed to a Neogene age, presents a strictly brttle character, being typilied by normal faults and slickenfibers of re-crystallized clayminerals, ali olthem displaying variable orientations. Although the present faults in the Xaréu Oil Field (and, consequently, in the Mundaú Sub-Basin) were classically relerred as struetures of essentially normal displacement, the kinematics analysis of the meso-to microscaie D1 struetures in the drill cores led to deline oblique displacements (normal with a clockwise strike-slip component) to these faults, indicating a main tectonic transport to ENE. These oblique movements would be responsible for the installation of a transtensive context in the Mundaú Sub-Basin, as part of the transcurrent to translormant opening of the Atlantic Equatorial Margin. The balancing of four struetural cross-sections ofthe Xaréu Oil Field indicates that the Mundaú Fault was responsible for more than 50% of the total stretching (ß factor) registered during the Early Aptian. At the initial stages of the "rifting", during Early Aptianuntil the Holocene, the Mundaú Sub-Basin (and consequently the Xaréu Oil Fleld) accumulated a total stretching between 1.21 and 1.23; in other words, the crust in this segment of the Atlantic Equatorial Margin was subjeeted to an elongation of about 20%. From estimates of oblique displacements related to the faults, it ws possible to construct diagrams that allow the determination of stretching factors related to these displacements. Using these diagrams and assuming the sense 01 dominant teetonictransport towards ENE, it was possible to calculate the real stretching lactors related to the oblique movement 0 of the faults in the Mundaú Sub-Basin. which reached actual values between 1.28 and 1.42. ln addnion to the tectonic-structural studies in the Xaréu Oil Field, the interpretation of remote sensing products, coupled wnh characterization of terrain analogues in seleeted areas along the northern Ceará State (continental margins of the Ceará and Potiguar basins), provided addnional data and constraints about the teetonic-structural evolution of the oil lield. The work at the analogue sites was particularly effective in the recognition and mapping, in semidetail scale, several generations of struetures originated under a brittle regime. Ali the obtained information (from the Xaréu Oil Field, the remote sensor data and the terrain analogues) were jointly interpreted, culminating with the proposnion of an evolutionary model lor this segment of the Atlantic Equatorial Margin; this model that can be applied to the whole Margin, as well. This segmentof the Atlantic Equatorial Margin was delormedin an early E-W (when considered lhe present-day position of the South American Plate) transcurrent to transform regime with dextral kinematics, started Irom, at least, the Early Aptian, which left its record in several outcrops along the continental margin of the Ceará State and specilically in the Xaréu off Field. The continuous operation of the regime, through the Albian and later periods, led to the definitive separation between the South American and African plates, with the formation of oceanic lithosphere between the two continental blocks, due to the emplacement off spreading centers. This process involved the subsequent transition of the transcurrent to a translorm dextral regime, creating lhe Equatorial Atlantic Oceano With the separation between the South American and African plates already completed and the increasing separation between lhe continental masses, other tecton ic mechanisms began to act during the Cenozoic (even though the Cretaceous tectonic regime lasted until the Neogene), like an E-W compressive stress líeld (related to the spreading olthe oceanic floor along lhe M id-Atlantic Ridge and to the compression of the Andean Chain) effective Irom the Late Cretaceous, and a state of general extension olthe horizontal surface (due to the thermal uplift ofthe central portion of Borborema Province), effective during the Neogene. The overlap of these mechanisms during the Cenozoic led to the imprint of a complex tectonic framework, which apparently influenced the migration and entrapment 01 hydrocarbon in the Ceará Basin

Reavaliação de critérios estruturais na hidrogeologia de terrenos cristalinos, com ênfase na neotectônica e sensoriamento remoto

Hydrogeological prospecting in Northeast Brazil and in other crystalline terrains has been developed on the basis of structural and regional geology concepts that date back to the 50-60 decades and, as such, demand a natural re-evaluation and update. In this kind of terrain, the percolation and accumulation of ground water are controlled by fractures and other types of discontinuities, such as foliations and geological contacts that, through weathering, impart porosity and permeability to the rocks, allowing water flow and storage. Several factors should be considered in the process of locating water wells, as discussed in the literature. Among these, the kind of structures, fracture geometry (including aperture and connectivity) and their geological and chronological context. It is important to correlate fracture systems with the regional neotectonic framework. Fractures at low angle (sub parallel) with the principal stress axis (s1) are those which tend to open (actually they work as tension joints) and, in principle, would present major hydric potential; in the opposite side, fractures at high angle to s1 would behave as closed by a compressional component. Fractures diagonal to the compression and tension axes correspond to shear fractures and, due to their connectivity with second fractures, are also important in terms of hydric potential. Uplift followed by terrain denudation leads to decompression and a general tendency to open (aided by weathering processes) fractures and other rock discontinuities, at different orientations. Low angle fractures, formed in this context, are equally important to increase connectivity, collection of water and recharge of the aquifer systems. In a general way, an opening component (neotectonic or by terrain decompression) and several models to increase fracture connectivity correlate with a greater hydric potential of these structures. Together with parallel research, this thesis addresses models of ground water occurrence in crystalline terrains, either improving well established concepts like the (Riacho-Fenda model), but also stressing other possibilities, like the role of alluvium and paleo-regoliths (the Calha Elúvio-Aluvionar model) and of strongly altered, permo-porous zones placed at variable depths below the present surface, flanking several types of discontinuities, especially interconnected fracture arrays (the Bolsões de Intemperismo model). Different methodological approaches are also discussed in order to improve success rates in the location of water wells in crystalline terrains. In this methodological review, a number of case studies were selected in the eastern domain of the State of Rio Grande do Norte, involving the localities of Santa Cruz, Santo Antônio, Serrinha, Nova Cruz, Montanhas, Lagoa de Pedras and Lagoa Salgada. Besides the neotectonic analysis of brittle structures, this Thesis addresses the validation of remote sensing as a tool for ground water prospecting. Several techniques were tested in order to detect and select areas with higher potential for ground water accumulation, using Landsat 5-TM and RADARSAT images, besides conventional aerial photos. A number of filters were tested to emphasize lineaments in the images, improving their discrimination, to identify areas with higher overburden humidity, which could reflect subsurface water accumulation, as well as alluvium and other sedimentary covers that might act as recharge zones. The work started with a regional analysis with the orbital images, followed by analysis of aerial photos, up to a detailed structural study of rock exposures in the terrain. This last step involved the analysis of outcrops surrounding wells (in a ray of approximately 10 to 100 m) with distinct productivities, including dry examples. At the level required for detail, it was not possible to accomplish a statistical approach using the available well data catalogs, which lack the desired specific information. The methodology worked out in this Thesis must undergo a testing phase through location of new water wells. An increase in the success rates as desired will led to a further consolidation step with wider divulgation of the methodology to private companies and governmental agencies involved in ground water prospecting in crystalline terrains

Litoestratigrafia e deformação cenzóica na região de Icapuí, Ceará, e implicações para a estruturação de campos de petróleo na borda ocidental da bacia Potiguar(NE do Brasil)

This thesis deals with the sedimentological/stratigraphic and structural evolution of the sedimentary rocks that occur in the NW continental border of the Potiguar Basin. These rocks are well exposed along coastal cliffs between the localities of Lagoa do Mato and Icapuí, Ceará State (NE Brazil). The sedimentological/stratigraphic study involved, at the outcrop scale, detailed facies descriptions, profile mapping of the vertical succession of different beds, and columnar sections displaying inferred lateral relationships. The approach was complemented by granulometric and petrographic analyses, including the characterization of heavy mineral assemblages. The data set allowed to recognize two kinds of lithological units, a carbonate one of very restricted occurrence at the base of the cliffs, and three younger, distinct siliciclastic units, that predominate along the cliffs, in vertical and lateral extent. The carbonate rocks were correlated to the late Cretaceous Jandaíra Formation, which is covered by the siliciclastic Barreiras Formation. The Barreiras Formation occurs in two distinct structural settings, the usual one with nondeformed, subhorizontal strata, or as tilted beds, affected by strong deformation. Two lithofacies were recognized, vertically arranged or in fault contacts. The lower facies is characterized by silty-argillaceous sandstones with low-angle cross bedding; the upper facies comprises medium to coarse grained sandstones, with conglomeratic layers. The Tibau Formation (medium to coarse-grained sandstones with argillite intercalations) occurs at the NW side of the studied area, laterally interlayered with the Barreiras Formation. Eolic sediments correlated to the Potengi Formation overly the former units, either displaying an angular unconformity, or simply an erosional contact (stratigraphic unconformity). Outstanding structural features, identified in the Barreiras Formation, led to characterize a neocenozoic stress field, which generated faults and folds and/or reactivated older structures in the subjacent late cretaceous (to paleogene, in the offshore basin) section. The structures recognized in the Barreiras Formation comprise two distinct assemblages, namely a main extensional deformation between the localities of Ponta Grossa and Redonda, and a contractional style (succeeded by oblique extensional structures) at Vila Nova. In the first case, the structural assemblage is dominated by N-S (N±20°Az) steep to gently-dipping extensional faults, displaying a domino-style or listric geometry with associated roll-over structures. This deformation pattern is explained by an E-W/WNW extension, contemporaneous with deposition of the upper facies of the Barreiras Formation, during the time interval Miocene to Pleistocene. Strong rotation of blocks and faults generated low-angle distensional faults and, locally, subvertical bedding, allowing to estimate very high strain states, with extension estimates varying between 40% up to 200%. Numerous detachment zones, parallel to bedding, help to acommodate this intense deformation. The detachment surfaces and a large number of faults display mesoscopic features analoguous to the ones of ductile shear zones, with development of S-C fabrics, shear bands, sigmoidal clasts and others, pointing to a hydroplastic deformation regime in these cases. Local occurrences of the Jandaíra limestone are controled by extensional faults that exhume the pre-Barreiras section, including an earlier event with N-S extension. Finally, WNWtrending extensional shear zones and faults are compatible with the Holocene stress field along the present continental margin. In the Vila Nova region, close to Icapuí, gentle normal folds with fold hinges shallowly pluging to SSW affect the lower facies of the Barreiras Formation, displaying an incipient dissolution cleavage associated with an extension lineation at high rake (a S>L fabric). Deposition of the upper facies siliciclastics is controlled by pull-apart graben structures, bordered by N-NE-trending sinistral-normal shear zones and faults, characterizing an structural inversion. Microstructures are compatible with tectonic deformation of the sedimentary pile, burried at shallow depths. The observed features point to high pore fluid pressures during deformation of the sediments, producing hydroplastic structures through mechanisms of granular flow. Such structures are overprinted by microfractures and microfaults (an essentially brittle regime), tracking the change to microfracturing and frictional shear mechanisms accompanying progressive dewatering and sediment lithification. Correlation of the structures observed at the surface with those present at depth was tested through geophysical data (Ground Penetrating Radar, seismics and a magnetic map). EW and NE-trending lineaments are observed in the magnetic map. The seismic sections display several examples of positive flower structures which affect the base of the cretaceous sediments; at higher stratigraphic levels, normal components/slips are compatible with the negative structural inversion characterized at the surface. Such correlations assisted in proposing a structural model compatible with the regional tectonic framework. The strong neogenepleistocene deformation is necessarily propagated in the subsurface, affecting the late cretaceous section (Açu and Jandaíra formations), wich host the hydrocarbon reservoirs in this portion of the Potiguar Basin. The proposed structural model is related to the dextral transcurrent/transform deformation along the Equatorial Margin, associated with transpressive terminations of E-W fault zones, or at their intersections with NE-trending lineaments, such as the Ponta Grossa-Fazenda Belém one (the LPGFB, itself controlled by a Brasiliano-age strike-slip shear zone). In a first step (and possibly during the late Cretaceous to Paleogene), this lineament was activated under a sinistral transpressional regime (antithetic to the main dextral deformation in the E-W zones), giving way to the folds in the lower facies of the Barreiras Formation, as well as the positive flower structures mapped through the seismic sections, at depth. This stage was succeeded (or was penecontemporaneous) by the extensional structures related to a (also sinistral) transtensional movement stage, associated to volcanism (Macau, Messejana) and thermal doming processes during the Neogene-Pleistocene time interval. This structural model has direct implications to hydrocarbon exploration and exploitation activities at this sector of the Potiguar Basin and its offshore continuation. The structure of the reservoirs at depth (Açu Formation sandstones of the post-rift section) may be controlled (or at least, strongly influenced) by the deformation geometry and kinematics characterized at the surface. In addition, the deformation event recognized in the Barreiras Formation has an age close to the one postulated for the oil maturation and migration in the basin, between the Oligocene to the Miocene. In this way, the described structural cenario represents a valid model to understand the conditions of hydrocarbon transport and acummulation through space openings, trap formation and destruction. This model is potentially applicable to the NW region of the Potiguar Basin and other sectors with a similar structural setting, along the brazilian Equatorial Atlantic Margin

Tecttôniica póss--riifftte na Baciia Pottiiguar

The study of Brazilian sedimentary basins concentrates on their rift phase, whereas the Post-rift phase has been considered a tectonic quiescent period. The post-rift sequence of the Potiguar Basin, in the far northeastern Brazil, was once considered little deformed, however several studies have shown how that it was affected by major fault systems. The purpose of this thesis is to characterize the post-rift tectonic. The specific objectives are: to characterize the Neogene and Quaternary sedimentary units that outcrop of the Potiguar Basin; to show how the NW-SEtrending Afonso Bezerra Faults System deformed outcrop rocks in the Basin; to describe soft-sediment deformation in gravels of the Quaternary Alluvial Deposits from Açu River. Facies analyses, grain-size studies, luminescence dating, remote sensing, structural mapping, shallow geophysics (georadar), paleostress and petrography were carried out. The structural mapping and the georadar sections indicated that the Carnaubais and Afonso Bezerra fault systems formed fractures, silicified and non-silicified faults or deformation bands, affecting mainly the Açu, Jandaíra and Barreiras formations. The petrographic data indicate that the strong silicification resulted in a sealant character of the faults. Paleostress analysis indicates that two stress fields affected the Basin: the first presented N-S-trending compression, occurred from the Neocretaceous to the Miocene; the second stress field presents E-W-trending compression, acts from the Miocene to the present. It was verified once the Afonso Bezerra System Faults was reactivated in periods post-Campanian and affects all post-rift lithostratigraphic units of Potiguar Basin, including Quaternary sedimentary covers. The study about soft-sediment deformation structures indicates that they are similar in morphology and size to modern examples of seismically-induced deformation strutures in coarse sediments. TL and OSL ages indicate that sediment deposition and associated soft-sediment deformation occurred at least six times from ~352 Ka to ~9 Ka. Finally these studies demonstrate how recent is tectonics in the Basin Potiguar

Geomorfologia e neotectônica no Vale do Apodi-Mossoró RN

Numerous studies have indicated that the Potiguar Basin is affected by Cenozoic tectonics. The reactivation of Cretaceous fault systems affect the post-rift units, witch include Neogene and overlying Quaternary sediments. In this context, the objectives of this thesis are the followings: (1) to characterize the effects of post-rift tectonics in the morphology of Apodi Mossoró-river valley located in the central portion of the Potiguar, (2) to characterize the drainage of the Apodi Mossoró river valley and investigate the behavior of their channels across active faults, and (3) to propose a geologic-geomorphological evolutionary model for the study area. This study used a geological and geomorphological mapping of the central part of the basin, with emphasis on the Quaternary record, luminescence dating of sediments, and geoelectric profiles of the area. The results reveal by maps of structural lineaments and drainage channels of the rivers form valleys that are affected by faults and folds. In Apodi-Mossoró valley, anomalies of channel morphology are associated with the deformation of the post-rift basin. These anomalies show the reactivation of major fault systems in the Potiguar Basin in Cenozoic. On a regional scale, can be seen through the vertical electric profiles that the Cenozoic tectonics is responsible for the elevation of a macro dome NE-SE-trending 70-km long and 50km wide and up to 270 above sea level. In this sector, the vertical electric profiles data show that the contact between the Cretaceous and Neogene rise more than 100m. This Is an important feature of inversion data obtained in this work showed that the deposits that cover the macro dome (Serra do Mel) have ages of 119 ka to 43 ka. In the river valley and surrounding areas Apodi-Mossoró ages vary between 319 ka and 2.7 ka. From these data it was possible to establish the correct geochronological posiconamento paleodepósitos of distinguishing them from the fluvial deposits of the Neogene (Barreiras Formation)

Evolução termocronológica do sistema de falhas Senador Pompeu-CE

The region of the Senador Pompeu Shear Zone (SPSZ), in the North Tectonic Domain of the Borborema Province (BP), has its recent history associated with to South Atlantic Ocean formation event at the Jurassic. A lot of geologics models have discussed about crustal axis elevation in local scale and large scale (Borborema Province), relative to importants regionals tectonics directions of it. The identification and the relationship among this surfaces, stepped in many topographyc levels by tectonics mecanisms, is dificult because of the erosion process on it. Over there, sedimentary deposits is complex and it has not biostratigraphyc record in continental deposits. The analysis metodology on apatita fission-track, in the region of the SPSZ, purpose the more knowledge about morphotectonics mecanisms of the area and the impruvement of its morphotectonics models. For this, it was moleled the age and thermal history of the 11 apatites samples collected on both sides of this shear zone, taking relationships among other results of the thermochronology studies in the BP. Based on the thermal studies in this search, the region of the BP developed on two distint cooling events, separated for one period of relative stabilited. The first episode occur between 130 and 90 M.y., has been began when the samples cross the 120°C isoterm for last time and fineshed at 70°C. The second moment of the cooling process was began about 30 M.y., when the temperature was 90°C, from this to the equlibrium with present surface temperature at 30°C. Some evidences indicated a relacionship between thermal episodes and uplift events of the regional relief. The fundaments of the interpretation was based mainly on comparatives studies among results of the thermochronology analysis and geologics studies about BP. Nóbrega et al.(2005), e.g., on studies about the Portalegre Shear Zone, got similar results on SPSZ, with some details relative to local tectonic activity. Morais Neto et al. (2000) interpreted two importants cooling events in the BP based on their regional studies, that can be associated to regional uplift events. When Assine (1992) studied the stratigraphyc sequences of the Araripe Basin, in the south of Ceará state, conclude that the abrupt return to continentals condictions from the last sedimentar sequency (albiano-cenomaniane) indicate a regional uplift of the NE region of the Brazil at the 100 M.y., in the Albiano Intermediate/Superior. This ages are compatible to termal model of the SPSZ. This two periods of the thermal history of the BP are completely registered in the apatites samples just one age groups of the fission-track, that it is the most ancient age groups. This one suggest it has happened in response to heating before 75 M.y and it has erased the last report of the first moment relief evolution of the BP. The NNE-SSW and E-W structure reativation can have created ideal condictions for heating and local elevations of the geothermal gradients. The equilibrium between the apatites temperatures of this groups and the regionais temperatures took place about 50 M.y., when the samples of the two ages groups had a simillar evolution to present surfaces temperatures