Biopolttoaineseoksen poltosta aiheutuvien ongelmien arviointityökalu.

Biopolttoaineiden erityispiirteitä ovat alhainen lämpöarvo, korkea kosteuspitoisuus ja suuri haihtuvien aineiden määrä. Lisäksi biopolttoaineiden tuhkat sisältävät runsaasti alkaleja. Näistä ominaisuuksista seuraa ongelmia, jotka on otettava huomioon biopolttoainetta polttavan voimalaitoksen suunnittelussa ja käytössä. Diplomityössä selvitetään biopolttoaineiden poltosta aiheutuvat ongelmat ja niiden syyt sekä kehitetään työkalu, jonka avulla voidaan arvioida biopolttoaineseoksen polton ongelmien syntymistä. Arviointi tapahtuu biopolttoaineseoksen ominaisuuksien perusteella. Kattilassa vallitsevien, polton aikaisten olosuhteiden vaikutusta syntyviin ongelmiin ei tässä työssä tarkastella. Kun lähtötiedoista lasketut, ongelmien synnyn kannalta olennaiset polttoaineseoksen ja sen tuhkan ominaisuudet tunnetaan, verrataan niitä työssä koottuihin raja-arvoihin. Jos laskettu arvo on suurempi kuin rajaksi asetettu arvo, on todennäköistä, että kattilassa esiintyy ongelmia. Suurimmat ongelmat biopolttoaineiden leijupoltossa ovat likakerrostumien muodostuminen lämpöpinnoille, leijukerroksen sintraantuminen ja agglomeroituminen sekä lämpöpintojen korkealämpötilakorroosio. Raja-arvoina käytetään sekä tutkimustuloksina saatuja että käytännön kokemuksiin perustuvia arvoja. Raja-arvoja määritettäessä on huomioitu niiden soveltuvuus tarkastelun kohteena olevalle voimalaitokselle, jonka tyyppi ja kokoluokka vaikuttavat käytettäviin raja-arvoihin. Työkalu tukee keskikokoisen biovoimalaitoksen, jossa palaminen tapahtuu kerrosleijukattilassa, tuotteistusprosessia. Työkalua käytetään voimalaitoksen tuotteistuksessa optimaalisen polttoaineseoksen etsimiseen, riskienhallintaan sekä konseptikehitykseen. Lisäksi työkalua tullaan käyttämään valmiin tuotteen myyntiin ja markkinointiin.

Development of Furnace Model for Bubbling Fluidized Bed Boiler

The aim of this thesis was to develop a model, which can predict heat transfer, heat release distribution and vertical temperature profile of gas phase in the furnace of a bubbling fluidized bed (BFB) boiler. The model is based on three separate model components that take care of heat transfer, heat release distribution and mass and energy balance calculations taking into account the boiler design and operating conditions. The model was successfully validated by solving the model parameters on the basis of commercial size BFB boiler test run information and by performing parametric studies with the model. Implementation of the developed model for the Foster Wheeler BFB design procedures will require model validation with existing BFB database and possibly more detailed measurements at the commercial size BFB boilers.

Uuttoprosessin suunnittelu

Teknologian kehitys ja prosessien tiukempi valvonta ovat alentaneet selluteollisuuden häviöitä tehden prosesseista suljetumpia. Valitettavasti nämä edistysaskeleet teknologiassa ovat lisänneet prosessiin kuulumattomien yhdisteiden määrää kemikaalien talteenottokierrossa. Näistä kemikaaleista haitallisimpia ovat kloridi- ja kaliumyhdisteet, jotka tulevat prosessiin raaka-aineiden ja prosessikemikaalien mukana. Kloridi ja kalium muodostavat emäksisissä liuoksissa epäorgaanisia liukoisia yhdisteitä, jotka rikastuvat lipeäkiertoon. Soodakattilassa kloridien läsnäolo alentaa tuhkan sulamislämpötilaa sekä tarttumispistettä, lisää korroosiota ja saostumien muodostumista kattilan pinnalle. Nämä seuraukset voivat vähentää vuosituotantoa ja nostaa korjauskustannuksia. Kaliumin ja kloridin rikastumista talteenottokiertoon voidaan estää poistamalla ne prosessista. Prosessiin kuulumattomat yhdisteet tulisi poistaa talteenottoprosessista ja säilyttää samalla korkea kemikaalien talteenottoprosentti. Koska kaliumin ja kloridin rikastumiskertoimet soodakattilan tuhkassa ovat korkeita, on tuhkan käsittely tehokasta. Kloridin ja kaliumin poistoon on kehitetty menetelmiä, joilla voidaan vähentää hyödyllisten kemikaalien häviöitä. Näitä menetelmiä ovat uutto, ioninvaihto, elektrodialyysi, jäähdytyskiteytys ja haihdutuskiteytys. Menetelmissä tuhka jaetaan kloridi- ja kaliumpitoiseen osaan ja natriumsulfaattipitoiseen osaan. Kloridi ja kalium poistetaan prosessista ja loput palautetaan lipeäkiertoon. Kloridin ja kaliumin poistoa tuhkasta tutkittiin uuttamalla tuhkaa vedellä. Parhaissa käyttöolosuhteissa natriumsulfaatin liukoisuus veteen on huomattavasti alhaisempi kuin kaliumkloridin liukoisuus veteen. Optimaalinen uuttolämpötila ja tuhka-vesisuhde määritettiin siten, että kloridi- ja kaliumpitoisuudet suodoksessa olivat mahdollisimman korkeat sekä natriumin ja muiden anioneiden pitoisuudet suodoksessa mahdollisimman alhaiset. Saatuja tuloksia käytettiin jatkuvatoimisen uuttoprosessin suunnittelussa.

Toward on-the-fly quantum mechanical/molecular mechanical (QM/MM) docking: development and benchmark of a scoring function.

We address the challenges of treating polarization and covalent interactions in docking by developing a hybrid quantum mechanical/molecular mechanical (QM/MM) scoring function based on the semiempirical self-consistent charge density functional tight-binding (SCC-DFTB) method and the CHARMM force field. To benchmark this scoring function within the EADock DSS docking algorithm, we created a publicly available dataset of high-quality X-ray structures of zinc metalloproteins ( http://www.molecular-modelling.ch/resources.php ). For zinc-bound ligands (226 complexes), the QM/MM scoring yielded a substantially improved success rate compared to the classical scoring function (77.0% vs 61.5%), while, for allosteric ligands (55 complexes), the success rate remained constant (49.1%). The QM/MM scoring significantly improved the detection of correct zinc-binding geometries and improved the docking success rate by more than 20% for several important drug targets. The performance of both the classical and the QM/MM scoring functions compare favorably to the performance of AutoDock4, AutoDock4Zn, and AutoDock Vina.

SALO, a novel classical pathway complement inhibitor from saliva of the sand fly Lutzomyia longipalpis.

Blood-feeding insects inject potent salivary components including complement inhibitors into their host's skin to acquire a blood meal. Sand fly saliva was shown to inhibit the classical pathway of complement; however, the molecular identity of the inhibitor remains unknown. Here, we identified SALO as the classical pathway complement inhibitor. SALO, an 11 kDa protein, has no homology to proteins of any other organism apart from New World sand flies. rSALO anti-complement activity has the same chromatographic properties as the Lu. longipalpis salivary gland homogenate (SGH)counterparts and anti-rSALO antibodies blocked the classical pathway complement activity of rSALO and SGH. Both rSALO and SGH inhibited C4b deposition and cleavage of C4. rSALO, however, did not inhibit the protease activity of C1s nor the enzymatic activity of factor Xa, uPA, thrombin, kallikrein, trypsin and plasmin. Importantly, rSALO did not inhibit the alternative or the lectin pathway of complement. In conclusion our data shows that SALO is a specific classical pathway complement inhibitor present in the saliva of Lu. longipalpis. Importantly, due to its small size and specificity, SALO may offer a therapeutic alternative for complement classical pathway-mediated pathogenic effects in human diseases.

Predicted decrease in global climate suitability masks regional complexity of invasive fruit fly species response to climate change

Climate change affects the rate of insect invasions as well as the abundance, distribution and impacts of such invasions on a global scale. Among the principal analytical approaches to predicting and understanding future impacts of biological invasions are Species Distribution Models (SDMs), typically in the form of correlative Ecological Niche Models (ENMs). An underlying assumption of ENMs is that species-environment relationships remain preserved during extrapolations in space and time, although this is widely criticised. The semi-mechanistic modelling platform, CLIMEX, employs a top-down approach using species ecophysiological traits and is able to avoid some of the issues of extrapolation, making it highly applicable to investigating biological invasions in the context of climate change. The tephritid fruit flies (Diptera: Tephritidae) comprise some of the most successful invasive species and serious economic pests around the world. Here we project 12 tephritid species CLIMEX models into future climate scenarios to examine overall patterns of climate suitability and forecast potential distributional changes for this group. We further compare the aggregate response of the group against species-specific responses. We then consider additional drivers of biological invasions to examine how invasion potential is influenced by climate, fruit production and trade indices. Considering the group of tephritid species examined here, climate change is predicted to decrease global climate suitability and to shift the cumulative distribution poleward. However, when examining species-level patterns, the predominant directionality of range shifts for 11 of the 12 species is eastward. Most notably, management will need to consider regional changes in fruit fly species invasion potential where high fruit production, trade indices and predicted distributions of these flies overlap.

Radiative Heat Transfer in Boiler Furnaces

Better models are needed for radiative heat transfer in boiler furnaces. If the process is known better, combustion in the furnace can be optimized to produce low emissions. It makes the process to be environmental friendly. Furthermore, if there is a better model of the furnace it can more fully explain what is happening inside the furnace. Using of the model one can quickly and easily analyze how it operates with bio fuels, moist fuels or difficult fuels and improve the operation. Models helps with better estimation of furnace dimensions and result in more accurate understanding of operation. Key component lacking in these models is radiative heat transfer in particle laden gases. If there are no particles than radiative heat transfer can be calculated approximately. There are two problems with current models when used with flow modeling. The first one is a need to account for a particle laden gas and the second one is an absence of a fast algorithm. Fast calculation is needed if radiative heat transfer calculation is done for a large CDF model. Computations slow down if time is required for calculating radiative properties over and over again. This thesis presents a band model for radiative heat transfer in boiler furnaces. Advantage is a quickness of calculation and account of particles in the process.

Fouling tendency in biomass-fired boilers

Although it is well known that firing biomass fuels leads to increased deposition buildup on heat transfer surfaces in boiler compared with firing coal, existing empirical knowledge about combustion of different types of biofuels is limited. The aim of this study is to give greater awareness and understanding of the circumstances which are able to decrease considerably deposition build up on heat transfer surfaces when firing different types of biofuels. The crucial part of this thesis is experimental investigation of fouling tendency while firing biomass fuels, such as straw, bark, and peat having different chemical composition. In order to give comprehensive overview of ash deposition phenomena the number of not less important issues such as mechanisms of ash deposition, effect of fouling on heat transfer, and design of boilers subjected to ash buildup were examined as well. The answers obtained in this study may be a step towards a better knowledge of firing biofuels as separately as in mixtures, and may provide solutions for successful combustion technique of biomass fuels.

Offdesign operation of kraft recovery boiler

A model to solve heat and mass balances during the offdesign load calculations was created. These equations are complex and nonlinear. The main new ideas used in the created offdesign model of a kraft recovery boiler are the use of heat flows as torn iteration variables instead of the current practice of using the mass flows, vectorizing equation solving, thus speeding up the process, using non dimensional variables for solving the multiple heat transfer surface problem and using a new procedure for calculating pressure losses. Recovery boiler heat and mass balances are reduced to vector form. It is shown that these vectorized equations can be solved virtually without iteration. The iteration speed is enhanced by the use of the derived method of calculating multiple heat transfer surfaces simultaneously. To achieve this quick convergence the heat flows were used as the torn iteration parameters. A new method to handle pressure loss calculations with linearization was presented. This method enabled less time to be spent calculating pressure losses. The derived vector representation of the steam generator was used to calculate offdesign operation parameters for a 3000 tds/d example recovery boiler. The model was used to study recovery boiler part load operation and the effect of the black liquor dry solids increase on recovery boiler dimensioning. Heat flows to surface elements for part load calculations can be closely approximated with a previously defined exponent function. The exponential method can be used for the prediction of fouling in kraft recovery boilers. For similar furnaces the firing of 80 % dry solids liquor produces lower hearth heat release rate than the 65 % dry solids liquor if we fire at constant steam flow. The furnace outlet temperatures show that capacity increase with firing rate increase produces higher loadings than capacity increase with dry solids increase. The economizers, boiler banks and furnaces can be dimensioned smaller if we increase the black liquor dry solids content. The main problem with increased black liquor dry solids content is the decrease in the heat available to superheat. Whenever possible the furnace exit temperature should be increased by decreasing the furnace height. The increase in the furnace exit temperature is usually opposed because of fear of increased corrosion.

Heat transfer in superheaters of the bubbling fluidized bed boiler conversions

It is often reasonable to convert old boiler to bubbling fluidized bed boiler instead of building a new one. Converted boiler consists of old and new heat surfaces which must be fitted to operate together. Prediction of heat transfer in not so ideal conditions sets challenges for designers. Two converted boilers situated in Poland were studied on the grounds of acceptance tests and further studies. Calculation of boiler process was performed with boiler design program. Main interest was heat transfer in superheaters and factors affecting it. Theory for heat transfer is presented according to information found from literature. Results obtained from experimental studies and calculations have been compared. With correct definitions calculated parameters corresponded well to measured data at boiler maximum design load. However overload situations revealed to be difficult to model at least without considering changes in the combustion process which requires readjustments to the design program input values.

Modern recovery boiler design criteria

Engineering and pricing of large recovery boiler were studied in this work. Engineering was carried out with Anita 4.2 which is an engineering program of Andritz. Key initial values were chosen with previous studies. Primary target of this work was to find out the consequences that furnace dimensions and furnace screen vertical part has to boiler pricing. Boilers that were engineered had different rate of furnace width and depth and different heat transfer plate count. Boiler balances were invariable. Boilers with different vertical screen construction were also calculated. First variation was boiler with vertical screen up to furnace roof. Other variation was to connect vertical screen to Pre-boiler generating bank inlet tubes. Total prices were calculated to engineered boilers. Pricing was sort out to heat transfers, high pressure pipes, steel structures, auxiliary equipments and civil/structural costs. This study did not notice parts of the boiler which costs do not vary with the construction of the boiler. Heat transfers had the largest share of costs. Boiler building had the most significant differences between the boilers. Furnace screen had also significant role especially to costs of the boiler building.

Diagnostiikkamenetelmät höyrykattilan leijukerroksen tilan ja käytettävyysongelmien tunnistamiseksi

Diplomityön tavoitteena oli tutkia höyrykattiloiden leijukerrosten käytettävyysongelmia ja kirjallisuudesta löytyvien diagnostiikkamenetelmien toimivuutta leijukerroksen tilan ja käytettävyysongelmien tunnistamiseksi. Diagnostiikkamenetelmien toimivuutta testattiin VTT:n kiertoleijukoelaitteen prosessimittauksiin perustuen. Analysoinnissa käytettiin prosessimittauksia, jotka ovat yleisesti käytössä energiantuotannon leijukerroskattiloissa. Analysoitavina koeajotapauksina olivat kylmäkokeet partikkelikokojakaumaltaan vaihtelevalle leijutusmateriaalille, tuhkapartikkelien aiheuttama petimateriaalin karkeneminen ja agglomeroituminen, sekä vaihtelevien ajoarvojen vaikutus leijukerroksen hydrodynaamiseen käyttäytymiseen. Kokeellisesta osiosta saaduista tuloksista selvisi leijutusilman tilavuusvirran, petimassan ja partikkelikoon vaikutus analysoitavaan prosessimittaukseen. Tuloksista oli havaittavissa myös kiertävän petimateriaalin ja pohjapedin osuuksien vaikutus mitattuun painesignaaliin. Petipartikkelien agglomeroitumisen ja karkenemisen todettiin lisäävän kiertoleijukoelaitteistossa nousuputken pohjapedin määrää suhteessa kiertävään petimateriaaliin, mikä voitiin havaita painemittauksista.

Production of silica gel from residual rice husk ash

This paper presents a study on the production of silica gel in hydrothermal process using residual rice husk ash. Measurements of the chemical composition, X-ray diffraction, infrared spectroscopy, particle size distribution, and pozzolanic activity were carried out in order to characterize the obtained material, and the optimal silica gel was selected for use as a mineral additive in cement pastes. The compressive strengths were determined for cement pastes containing silica gel (0.0, 2.5 or 5% by mass) in different times. The results indicate that the mixtures containing silica gel showed improved mechanical behavior over all time periods evaluated.

Properties of silica from rice husk and rice husk ash and their utilization for zeolite y synthesis

This study compared properties of silica (SiO2) from rice husk (RH) and rice husk ash (RHA) extracted by acid- and heat-treatment. The SiO2 from RH was in amorphous phase with nearly 100% purity while that from RHA was in crystalline phase with 97.56% purity. Both extracted SiO2 were used in the synthesis of zeolite NaY but that from RH was better due to the efficiency in product recovery and simplicity of extraction. After the NaY was exchanged to NH4Y and calcined to convert to HY, the product did not carry over the textural properties of the parent NaY and NH4Y.