An experimental approach to air gap optimisation for a correction-less small field diode

Aim A recent Monte Carlo based study has shown that it is possible to design a diode that measures small field output factors equivalent to that in water. This is accomplished by placing an appropriate sized air gap above the silicon chip (1) with experimental results subsequently confirming that a particular Monte Carlo design was accurate (2). The aim of this work was to test if a new correction-less diode could be designed using an entirely experimental methodology. Method: All measurements were performed on a Varian iX at a depth of 5 cm, SSD of 95 cm and field sizes of 5, 6, 8, 10, 20 and 30 mm. Firstly, the experimental transfer of kq,clin,kq,msr from a commonly used diode detector (IBA, stereotactic field diode (SFD)) to another diode detector (Sun Nuclear, unshielded diode, (EDGEe)) was tested. These results were compared to Monte Carlo calculated values of the EDGEe. Secondly, the air gap above the EDGEe silicon chip was optimised empirically. Nine different air gap “tops” were placed above the EDGEe (air depth = 0.3, 0.6, 0.9 mm; air width = 3.06, 4.59, 6.13 mm). The sensitivity of the EDGEe was plotted as a function of air gap thickness for the field sizes measured. Results: The transfer of kq,clin,kq,msr from the SFD to the EDGEe was correct to within the simulation and measurement uncertainties. The EDGEe detector can be made “correction-less” for field sizes of 5 and 6 mm, but was ∼2% from being “correction-less” at field sizes of 8 and 10 mm. Conclusion Different materials will perturb small fields in different ways. A detector is only “correction-less” if all these perturbations happen to cancel out. Designing a “correction-less” diode is a complicated process, thus it is reasonable to expect that Monte Carlo simulations should play an important role.

Dancing through the Air (parts one and 2) - Spirit of Akasha

Recording for ARIA nominated Film Soundtrack for Spirit of Akasha. Recorded, Mixed, and Co-produced by Phil Graham. Published by Warner Music Australia

A national satellite-based land-use regression model for air pollution exposure assessment in Australia

Land-use regression (LUR) is a technique that can improve the accuracy of air pollution exposure assessment in epidemiological studies. Most LUR models are developed for single cities, which places limitations on their applicability to other locations. We sought to develop a model to predict nitrogen dioxide (NO2) concentrations with national coverage of Australia by using satellite observations of tropospheric NO2 columns combined with other predictor variables. We used a generalised estimating equation (GEE) model to predict annual and monthly average ambient NO2 concentrations measured by a national monitoring network from 2006 through 2011. The best annual model explained 81% of spatial variation in NO2 (absolute RMS error=1.4 ppb), while the best monthly model explained 76% (absolute RMS error=1.9 ppb). We applied our models to predict NO2 concentrations at the ~350,000 census mesh blocks across the country (a mesh block is the smallest spatial unit in the Australian census). National population-weighted average concentrations ranged from 7.3 ppb (2006) to 6.3 ppb (2011). We found that a simple approach using tropospheric NO2 column data yielded models with slightly better predictive ability than those produced using a more involved approach that required simulation of surface-to-column ratios. The models were capable of capturing within-urban variability in NO2, and offer the ability to estimate ambient NO2 concentrations at monthly and annual time scales across Australia from 2006–2011. We are making our model predictions freely available for research.

Enhancing sense of recovery and self-reflectivity in people with schizophrenia : a pilot study of Metacognitive Narrative Psychotherapy

Objective This study investigated the effectiveness of an innovative, manualized psychotherapy aimed at enhancing recovery and self-experience in people with schizophrenia, Metacognitive Narrative Psychotherapy. Design Treatment effects were assessed using a mixed methodology. Data were quantitatively assessed using a single sample, pre- and post-therapy design and qualitatively assessed using a case-study methodology. Methods Eleven patients diagnosed with schizophrenia received Metacognitive Narrative Psychotherapy over the course of 11 to 26 months. Therapists were seven supervised postgraduate psychology students. On average patients attended 49 sessions over the course of therapy. Patients completed interview-based and self-report measures for general and treatment-specific outcomes at pre-, mid-, and post-treatment. Results Quantitative analyses showed that patients significantly improved on the general outcome of subjective recovery, as well as the treatment-specific outcome of self-reflectivity, with medium to large effect sizes. Case-study evidence also showed improvements for some patients in symptom severity, and narrative coherence and complexity. Conclusions These results are consistent with previous case-study evidence and suggest that this manualized version of Metacognitive Narrative Psychotherapy produces general and approach-specific improvements for people with schizophrenia. Replication is needed to ascertain its effectiveness with a larger sample size and within a controlled design.

Pharmacy educators' intention for the curriculum : an Australian pilot study

Background: Pharmacy educators play an important role in supporting the professional identity formation of students, particularly in relation to their perceptions and strategies for the curriculum and subsequent learning experiences. Aim: To explore pharmacy educators’ perceptions of the purpose of the pharmacy curriculum and how they contribute to students’ development as pharmacists. Methods: A one-off survey using a 20-item questionnaire distributed to all pharmacy educators at a single school of pharmacy who contributed to an Australian undergraduate pharmacy degree program. Results: Most educators viewed the curriculum and their role from a traditional perspective. The educators felt the key purpose of the curriculum was to develop competent pharmacists by providing students with knowledge and skills. There was a limited emphasis on patient-centredness. Conclusion: Whilst educators were focused on developing competent pharmacists through the provision of knowledge and skills, important learning opportunities supporting identity formation may be missed.

Effectiveness of a puppet show on iodine knowledge, attitudes and behaviour of elementary students and the indirect effects on their parents and households in Ho Chi Minh City : a pilot study

Deficiencies in iodine levels have been shown to seriously affect a child’s intellectual development and learning capacity.1 In South-East Asia, iodine deficiency remains a major public health concern. Approximately 30% of the region’s population of 503.6 million have insufficient iodine intake, and only 61% of households have access to iodized salt.1 For this reason, it is necessary to initiate effective, community-based health promotion activities that are targeted toward populations of various ages. A puppet show is one imaginative and entertaining method of health education that has been advocated for use in communicating positive health behaviours to children.2e5 The authors undertook a literature review and found no studies assessing the effectiveness of a puppet show to teach an iodine education programme...

Design and experimental testing of air slab caps which convert commercial electron diodes into dual purpose, correction-free diodes for small field dosimetry

Purpose Two diodes which do not require correction factors for small field relative output measurements are designed and validated using experimental methodology. This was achieved by adding an air layer above the active volume of the diode detectors, which canceled out the increase in response of the diodes in small fields relative to standard field sizes. Methods Due to the increased density of silicon and other components within a diode, additional electrons are created. In very small fields, a very small air gap acts as an effective filter of electrons with a high angle of incidence. The aim was to design a diode that balanced these perturbations to give a response similar to a water-only geometry. Three thicknesses of air were placed at the proximal end of a PTW 60017 electron diode (PTWe) using an adjustable “air cap”. A set of output ratios (ORfclin Det ) for square field sizes of side length down to 5 mm was measured using each air thickness and compared to ORfclin Det measured using an IBA stereotactic field diode (SFD). k fclin, f msr Qclin,Qmsr was transferred from the SFD to the PTWe diode and plotted as a function of air gap thickness for each field size. This enabled the optimal air gap thickness to be obtained by observing which thickness of air was required such that k fclin, f msr Qclin,Qmsr was equal to 1.00 at all field sizes. A similar procedure was used to find the optimal air thickness required to make a modified Sun Nuclear EDGE detector (EDGEe) which s “correction-free” in small field relative dosimetry. In addition, the feasibility of experimentally transferring k fclin, f msr Qclin,Qmsr values from the SFD to unknown diodes was tested by comparing the experimentally transferred k fclin, f msr Qclin,Qmsr values for unmodified PTWe and EDGEe diodes to Monte Carlo simulated values. Results 1.0 mm of air was required to make the PTWe diode correction-free. This modified diode (PTWeair) produced output factors equivalent to those in water at all field sizes (5–50 mm). The optimal air thickness required for the EDGEe diode was found to be 0.6 mm. The modified diode (EDGEeair) produced output factors equivalent to those in water, except at field sizes of 8 and 10 mm where it measured approximately 2% greater than the relative dose to water. The experimentally calculated k fclin, f msr Qclin,Qmsr for both the PTWe and the EDGEe diodes (without air) matched Monte Carlo simulated results, thus proving that it is feasible to transfer k fclin, f msr Qclin,Qmsr from one commercially available detector to another using experimental methods and the recommended experimental setup. Conclusions It is possible to create a diode which does not require corrections for small field output factor measurements. This has been performed and verified experimentally. The ability of a detector to be “correction-free” depends strongly on its design and composition. A nonwater-equivalent detector can only be “correction-free” if competing perturbations of the beam cancel out at all field sizes. This should not be confused with true water equivalency of a detector.

Triumphs and tribulations in the psychotherapy of schizophrenia : reflections on a pilot study of metacognitive narrative psychotherapy

Schizophrenia results in a profound disruption of one’s capacity to make sense of mental states, coherently narrate self-experiences, and meaningfully relate to others. While current treatment options for people with schizophrenia tend to be symptom-focused, experience in designing and implementing a study focusing on enhancing sense of self demonstrates the feasibility of developing and implementing models of treatment that prioritize the subjective distress and self-experience of people with schizophrenia. There is emerging research evidence, based upon dialogical theory of self, that posits the potential of people with deficits of self to engage in meaningful therapeutic relationships and work toward greater integrity of self and degrees of recovery. The challenge is to translate these ideas into a research methodology that can be successfully applied within therapeutic contexts with people who meet the diagnostic criteria for schizophrenia. Based upon dialogical theory, we developed a principle-based manual for metacognitive narrative psychotherapy: a psychological approach to the treatment of people with schizophrenia, which aims to enhance metacognitive capacity and ability to narrate self-experiences. Five phases of treatment were identified: (1) developing a therapeutic relationship, (2) eliciting narratives, (3) enhancing metacognitive capacity, (4) enriching narratives, and (5) living enriched stories. Proscribed practices were also identified. We then implemented the manual within a university clinic context. Six therapists were trained to implement the model and, in turn, provided therapy to 11 patients who completed 12 to 24 months of treatment. Participants were assessed on metacognitive capacity, narrative coherence, narrative richness, self-reported recovery, and symptomatology at three points in time over the course of therapy. Contrary to expectations, participants were highly engaged in the therapeutic process, with minimal dropout. Overall, over 75% of participants evidenced improvement in their level of recovery over the course of therapy. The manualization and outcome findings demonstrate the feasibility of applying such interventions to a broader clinical population.

Ethical values in emergency medical services: A pilot study

Background Ambulance professionals often address conflicts between ethical values. As individuals’ values represent basic convictions of what is right or good and motivate behaviour, research is needed to understand their value profiles. Objectives To translate and adapt the Managerial Values Profile to Spanish and Swedish, and measure the presence of utilitarianism, moral rights and/or social justice in ambulance professionals’ value profiles in Spain and Sweden. Methods The instrument was translated and culturally adapted. A content validity index was calculated. Pilot tests were carried out with 46 participants. Ethical considerations This study conforms to the ethical principles for research involving human subjects and adheres to national laws and regulations concerning informed consent and confidentiality. Findings Spanish professionals favoured justice and Swedish professionals’ rights in their ambulance organizations. Both countries favoured utilitarianism least. Gender differences across countries showed that males favoured rights. Spanish female professionals favoured justice most strongly of all. Discussion Swedes favour rights while Spaniards favour justice. Both contexts scored low on utilitarianism focusing on total population effect, preferring the opposite, individualized approach of the rights and justice perspectives. Organizational investment in a utilitarian perspective might jeopardize ambulance professionals’ moral right to make individual assessments based on the needs of the patient at hand. Utilitarianism and a caring ethos appear as stark opposites. However, a caring ethos in its turn might well involve unreasonable demands on the individual carer’s professional role. Since both the justice and rights perspectives portrayed in the survey mainly concern relationship to the organization and peers within the organization, this relationship might at worst be given priority over the equal treatment and moral rights of the patient. Conclusion A balanced view on ethical perspectives is needed to make professionals observant and ready to act optimally – especially if these perspectives are used in patient care. Research is needed to clarify how justice and rights are prioritized by ambulance services and whether or not these organization-related values are also implemented in patient care.

Integrating ‘role play’ in assessment to strengthen professional conduct and accountability of students : a pilot study

BACKGROUND In a process engineering setting, graduates are frequently allocated reviews of existing operations or required to scope new production processes by their supervisors with a view to improving or expanding on operations and overall productivity. These tasks may be carried out in teams and in consultation with the process engineer’s immediate line manager or a more experienced engineer, such as the Production or Maintenance Manager; ultimately reporting to senior management, which is frequently a non-engineer. Although professional skills development is part of engineering curricula, ‘professional conduct’ and ‘accountability’ required for dealing with peers and superiors in industry is not very well addressed at university. Consequently, upon graduation, many students are, in terms of knowledge and experience in this area, underprepared to work effectively in industry settings. PURPOSE The purpose of this study was to develop and implement a role-play scenario within a core 2nd year process engineering unit, so that students could gain knowledge, skills and experience in different aspects (and nuances) of professional conduct and accountability. DESIGN/METHOD In the role-play scenario, students worked in ‘engineering production teams’ to design a process for an iconic Queensland fruitcake and to present their solution and recommendations (culminating in a poster presentation) to an assessment panel consisting of staff, role-playing as, ‘production and plant managers’. Students were assessed on several areas, including professionalism using a criteria referenced assessment guide by a 3-member cross-disciplinary staff panel consisting of a Business Faculty lecturer, an engineer from industry and the lecturer of the Process Engineering unit. Professional conduct and accountability was gauged through direct questioning by the panel. Feedback was also sought from students on various aspects through a survey questionnaire after the role play activity at the end of semester. RESULTS Overall, the role play was very well performed with students achieving an average score of 79.3/100 (distinction grade). Professional conduct as assessed by panel was on average better than scores given for professional accountability (4.0 compared with 3.6 out of 5). Feedback from students indicated that the learning activities had contributed to their overall understanding of the content and the role of process engineers. Industry involvement was rated very highly as contributing to their learning at 4.8 (on Likert scale from 1 – 5) and the poster presentation was rated at 3.6. CONCLUSIONS This pilot study was successful in implementing a new assessment task for modelling professional conduct and accountability within a 2nd year core unit. This task incorporated a role-play activity and there was evidence to suggest that this and associated learning tasks were successful in broadening students’ understanding and skills in this area required for engineering practice. Following feedback given by students and staff, improvements will be made to the nature of the problem, how it is defined, its assessment, and the approach taken in the role-play scenario when the unit is offered in 2014.