Avaliação das propriedades higroscópicas da madeira de Eucalyptus saligna Sm., em diferentes condições de umidade relativa do ar

O estudo da higroscopicidade é indispensável para o entendimento da trabalhabilidade, estabilidade dimensional, resistência mecânica e durabilidade natural da madeira. Neste trabalho objetivou-se a avaliação do teor de equilíbrio higroscópico para diversas condições de umidade relativa do ar, bem como da retratibilidade linear e volumétrica e da densidade básica da madeira de Eucalyptus saligna Sm. A madeira utilizada foi proveniente de árvores com 16 anos de idade, procedentes de talhões experimentais da EMBRAPA Florestas de Colombo, Paraná. Amostras com dimensões de 1,0x2,0x3,0 cm, sendo a última na direção longitudinal, foram colocadas em uma câmara fechada, sob ventilação, próximas de recipientes com soluções salinas supersaturadas, a fim de atingir determinada condição preestabelecida de teor de equilíbrio higroscópico. Após o equilíbrio da umidade da madeira nas distintas condições de umidade relativa, as amostras foram secas em estufa, para posterior avaliação. Os dados relativos à umidade de equilíbrio ajustaram-se muito bem às condições de umidade relativa adotadas neste estudo, tendo sido possível estimar com grande precisão o teor de equilíbrio higroscópico, para a faixa de aproximadamente 20 até 100% de umidade relativa. A madeira em estudo apresentou dados de retratibilidade bastante elevados, se comparados aos de outras da mesma faixa de densidade. Apesar dos elevados coeficientes de contração, o fator anisotrópico ou relação T/R mostrou-se próximo daquele encontrado na grande maioria das madeiras comerciais brasileiras. Verificaram-se ainda coeficientes de contrações mais suaves nos teores de umidade abaixo de 17%.

Modelagem e simulação de um secador intermitente de fluxos contracorrentes para frutos do cafeeiro

Este trabalho foi realizado com o objetivo de desenvolver um modelo computacional para simular a secagem de frutos café em um secador intermitente de fluxos contracorrente, empregando a linguagem de simulação EXTEND™ e o Modelo de Thompson (THOMPSON; PEART; FOSTER, 1968). Para validação do modelo desenvolvido foram utilizados dados experimentais obtidos por Silva (1991), em que foram empregados três níveis de temperatura do ar de secagem de 60, 80 e 100 °C. O modelo desenvolvido foi validado, sendo constatados desvios absolutos de 1,8% b.u e 1,1 kg e erros relativos de 11% e 1,6% na previsão dos parâmetros teor de água final e consumo de lenha, respectivamente. O modelo validado foi empregado na condução de experimentos tipo comparação de cenários. O primeiro experimento refere a alterações do ciclo operacional em que foram alterados os tempos de movimentação e de parada do fluxo da massa de grãos. E o segundo refere à alteração da configuração do secador quanto às alturas das câmaras de secagem e descanso. O ciclo operacional com os tempos de movimentação de um minuto e de parada de dezesseis minutos, para a temperatura do ar de secagem de 100 °C, proporcionou o melhor desempenho, sendo constatado tempo secagem de 12,3 h, consumo de lenha de 109,5 kg, consumo específico de energia de 7660 kJ.kg-1 de água evaporada, e capacidade de secagem de 87,86 kg.h-1. Quanto à configuração do secador, o melhor desempenho ocorreu para altura da câmara de secagem de 2,3 m usando a temperatura do ar de secagem de 100 °C, em que foram simulados tempo de secagem de 12,0 h, consumo de lenha de 106,5 kg, consumo específico de energia, de 7433 kJ.kg-1 de água evaporada, e capacidade de secagem de 90 kg.h-1. Desse modo, na condução da secagem de frutos de café em um secador intermitente de fluxos contracorrentes é recomendado o ciclo operacional com tempos de movimentação de um minuto e o de parada de dezesseis minutos, e não empregar a câmara de descanso. Essa conclusão está fundamentada em índices de desempenho do secador. Ressalta-se que não foram simulados os impactos nos parâmetros de qualidade.

Fighting climate change in the air: lessons from the EU directive on global aviation

The European Union's (EU) decision to include aviation into the Emissions Trade Scheme was heatedly contested. Countries around the world, but mainly the Brazil, Russia, India, China and South Africa group (BRICS) and the US, denounced the EU's initiate as illegal and unilateral. Following a decade of frustrated negotiations at the International Civil Aviation Organization (ICAO), this paper interrogates why such measure, in principle climate-friendly, inspired so much global resentment. I argue that concerns with competitiveness and risks of legal inconsistency are important, but insufficient elements to explain the core of the conflict. The paper suggests that the EU was strongly criticized because third countries perceived this action as an imposed solution, which fostered an environment of distrust. Therefore, I claim that the problem has more to do with a normative divide than with a substantive divergence on what should be done regarding aviation emissions. My analysis is informed by the present literature on the links between trade and climate change, but gives particular weight to first-hand information through interviews with key stakeholders. The paper is divided in three parts. First, it presents the scope of the EU directive in historical perspective. Second, it explores the EU's measure through three different angles: legal, economical and political. The final part explores some possible solutions to overcome these divergences.

SPAD-502 readings in response to photon fluence in leaves with different chlorophyll content

The chlorophyll meter (SPAD-502) is widely used to estimate chlorophyll content, but non-uniform chloroplast distribution can affect its accuracy. This study aimed to assess the effect of photon fluence (F, irradiance x time of illumination) in leaves with different chlorophyll content and determine the effect of chlorophyll a/b on SPAD values of four tropical tree species (Croton draconoides Müll. Arg., Hevea guianensis Aubl., Hymenaea courbaril L. and Matisia cordata H.B.K.). There were also determined calibration equations for the chlorophyll meter and assessed the effect of F on SPAD values between 07:00 h and 17:00 h. Calibration equations were obtained after determining leaf chlorophyll content in the laboratory. Increases in F with time caused a reduction in SPAD values in species with a high chlorophyll content, with reductions of 20% in M. cordata and 10% in H. guianensis. Leaves of C. draconoides and H. courbaril had lower chlorophyll content and showed no changes in SPAD values with increase in F. The chlorophyll a/b ratio increased with SPAD values and the SPAD/chlorophyll relationship was best described by an exponential equation. It seems that F may affect SPAD values in leaves with high chlorophyll content, probably due to non-uniform chloroplast distribution at high irradiance. This indicates that SPAD values tend to be more accurate if recorded early in morning when irradiance is low.

Correlation between grain nutritional content and pasting properties of pre-gelatinized red rice flour

As with any variety of rice, red rice characteristics are subject to varietal differences, growing conditions, types of processing, and nutritional and rheological properties. This study determined the nutritional characteristics (centesimal composition and minerals) and paste viscosity properties of raw grains of four red rice genotypes (Tradicional MNAPB0405, MNACE0501 and MNACH0501) and the paste viscosity properties of pre-gelatinized flours obtained at different cooking times (20, 30 and 40 min). The main nutritional properties were correlated with the pasting properties of the pre-gelatinized flours. The samples showed differences in nutritional properties and paste viscosity. MNAPB0405 and MNACE0501 showed higher levels of fiber and fat and provided higher caloric energy than Tradicional and MNACH0501, which, in turn, showed higher levels of amylose. MNACH0501 showed higher peak viscosity (2402 cP), higher breakdown viscosity (696 cP) and a greater tendency to retrogradation (1510 cP), while Tradicional, MNAPB0405 and MNACE0501 had pasting profiles with peak viscosities varying between 855 and 1093 cP, breaking viscosity below 85 cP and retrogradation tendency between 376 and 1206 cP. The factors genotype and cooking time influenced the rheological behavior of pre-gelatinized flours, decreasing their pasting properties. The protein and amylose levels are correlated with the pasting properties and can be used as indicators of these properties in different genotypes of red rice, whether raw or processed into pre-gelatinized flours.

Drying kinetics of jatropha seeds

Given the necessity of developing jatropha cultivation equipment, this work adjusted different mathematical models to experimental data obtained from the drying of jatropha seeds submitted to different drying conditions and selected the best model to describe the drying process. The experiment was carried out at the Federal Institute of Goiás - Rio Verde Campus. Seeds with initial moisture content of approximately 0.50 (kg water/kg dry matter) were dried in a forced air-ventilated oven, at temperatures of 45, 60, 75, 90 and 105°C to moisture content of 0.10 ± 0.005 (kg water/kg dry matter). The experimental data were adjusted to 11 mathematical models to represent the drying process of agricultural products. The models were compared using the coefficient of determination, chi-square test, relative mean error, estimated mean error and residual distribution. It was found that the increase in the air temperature caused a reduction in the drying time of seeds. The models Midilli and Two Terms were suitable to represent the drying process of Jatropha seeds and between them the use of the Midili model is recommended due to its greater simplicity.

Carbon Nanofiber Type and Content Dependence of the Physical Properties of Carbon Nanofiber Reinforced Polypropylene Composites

The variation of the physical properties of four differ- ent carbon nanofibers (CNFs), based-polymer nano- composites incorporated in the same polypropylene (PP) matrix by twin-screw extrusion process was investigated. Nanocomposites fabricated with CNFs with highly graphitic outer layer revealed electrical isolation-to-conducting behaviors as function of CNF’s content. Nanocomposites fabricated with CNFs with an outer layer consisting on a disordered pyro- litically stripped layer, in contrast, revealed better mechanical performance and enhanced thermal sta- bility. Further, CNF’s incorporation into the polymer increased the thermal stability and the degree of crystallinity of the polymer, independently on the filler content and type. In addition, dispersion of the CNFs’ clusters in PP was analyzed by transmitted light opti- cal microscopy, and grayscale analysis (GSA). The results showed a correlation between the filler concentration and the variance, a parameter which measures quantitatively the dispersion, for all composites. This method indicated a value of 1.4 vol% above which large clusters of CNFs cannot be dispersed effectively and as a consequence only slight changes in mechanical performance are observed. Finally, this study establishes that for tailoring the physical properties of CNF based-polymer nanocomposites, both adequate CNFs structure and content have to be chosen.

Effect of filler content on morphology and physical-chemical characteristics of poly(vinylidene fluoride)/NaY-zeolite filled membranes

Poly(vinylidene fluoride) electrospun membranes have been prepared with different NaY zeolite contents up to 32%wt. Inclusion of zeolites induces an increase of average fiber size from ~200 nm in the pure polymer up to ~500 nm in the composite with 16%wt zeolite content. For higher filler contents, a wider distribution of fibers occurs leading to a broader size distributions between the previous fiber size values. Hydrophobicity of the membranes increases from ~115º water contact angle to ~128º with the addition of the filler and is independent on filler content, indicating a wrapping of the zeolite by the polymer. The water contact angle further increases with fiber alignment up to ~137º. Electrospun membranes are formed with ~80 % of the polymer crystalline phase in the electroactive  phase, independently on the electrospinning processing conditions or filler content. Viability of MC3T3-E1 cells on the composite membranes after 72 h of cell culture indicates the suitability of the membranes for tissue engineering applications.

Shape and size of jatropha beans (Jatropha curcas L.) during drying at different temperatures

This study was carried out to study the physical properties of the jatropha beans over the drying under six air conditions, based on measurements of roundness, sphericity, volume, superficial area, projected area and surface/volume ratio. Jatropha beans with moisture content around 0.61 (decimal d.b.) were subjected to thin-layer drying in oven with forced-air circulation under six temperature conditions (36, 45, 60, 75, 90 and 105 °C) and relative humidity of 31.7; 19.6; 9.4; 4.8; 2.6 and 1.5% respectively, until reaching the moisture content of 0.11 ± 0.006 (decimal d. b.). The results showed that the necessary time for jatropha beans to reach the moisture content of 0.11 ± 0.006 (decimal d.b.) were 1.5; 2.25; 3.0; 4.75; 6.75 and 12.0 h for the drying temperatures of 105, 90, 75, 60, 45 and 36 °C, respectively; and the reduction in the moisture content as well as the drying conditions promoted changes in the shape and reduced the size of the jatropha beans.

Leaf area and epicuticular wax content of Sida spp

Morpho-physiological characteristics and chemical composition are directly related to superior competitive ability of crops. This study intended to make a comparative analysis of dry matter production, leaf area and amount of epicuticular wax of three species of Sida spp: S. urens L., S. rhombifolia L. and S. spinosa L. Plants were collected at three growth stages: V1: stage described as up to 10 fully expanded leaves; V2: between 11 leaves and flowering; and R: after flowering. At stages V2 and R, the highest number of leaves was recorded for S. rhombifolia, followed by S. spinosa at V2 and S. urens at R. These results were relatively proportional to leaf area for all species. S. spinosa at the vegetative stage produced the highest values of specific leaf area (SLA), with no significant differences between species at the stage R. The amount of wax per unit of leaf area between species at the same developmental stage was significantly different only at the reproductive stage, where S. spinosa produced 23.18 and 6.23 fold more wax than S. urens and S. rhombifolia respectively. Between the growth stages of each species, there was decrease in the amount of wax with plant age and increase in leaf area (AFE), number of leaves and dry matter. The leaves of the Sida species exhibit different characteristics and this information can be used to optimize the use of herbicides in the control of these weeds.

Effect of biostimulant application on production and flavonoid content of marigold (Calendula officinalis L.)

The production of medicinal plants as raw material for industry must associate quality with biomass formation and, with this purpose, the application of plant growth regulators has been studied in these crops. The objective of this study was to evaluate the effect of a biostimulant on growth, inflorescence production and flavonoid content in marigold. The experiment was conducted in a greenhouse and the treatments consisted of increasing doses of the biostimulant (0, 3, 6, 9, 12 and 15 mL L-1) applied by foliar spraying in ten consecutive applications. The experiment was arranged in a completely randomized design, with six treatments and ten repetitions. The number of leaves and flowerheads and dry matter of roots increased linearly with increasing doses of the growth promoter, with 20%, 36.97% and 97.28% increases, respectively, compared with the control. The total dry mass and shoot dry mass showed maximum values at the highest dose tested of 15 mL L-1 (with increases of 40.09% and 46.30%, respectively). Plant height and flavonoid content reached the highest values at a dose of 6 mL L-1. The biostimulant promoted the development of marigold and positively influenced the synthesis of the secondary compound of medicinal interest. Among the tested doses, the application of rates between 6 and 9 mL L-1 of the biostimulant is recommended for more efficient large-scale production of marigold.

Juvenile tree growth correlates with photosynthesis and leaf phosphorus content in central Amazonia

Light and soil water availability may limit carbon uptake of trees in tropical rainforests. The objective of this work was to determine how photosynthetic traits of juvenile trees respond to variations in rainfall seasonality, leaf nutrient content, and opening of the forest canopy. The correlation between leaf nutrient content and annual growth rate of saplings was also assessed. In a terra firme rainforest of the central Amazon, leaf nutrient content and gas exchange parameters were measured in five sapling tree species in the dry and rainy season of 2008. Sapling growth was measured in 2008 and 2009. Rainfall seasonality led to variations in soil water content, but it did not affect leaf gas exchange parameters. Subtle changes in the canopy opening affected CO2 saturated photosynthesis (A pot, p = 0.04). Although A pot was affected by leaf nutrient content (as follows: P > Mg > Ca > N > K), the relative growth rate of saplings correlated solely with leaf P content (r = 0.52, p = 0.003). At present, reduction in soil water content during the dry season does not seem to be strong enough to cause any effect on photosynthesis of saplings in central Amazonia. This study shows that leaf P content is positively correlated with sapling growth in the central Amazon. Therefore, the positive effect of atmospheric CO2 fertilization on long-term tree growth will depend on the ability of trees to absorb additional amount of P

Comparison of body fat content and distribution of familial amyloidotic polyneuropathy patients versus healthy subjects

The deposition of amyloid fibers at the peripheral nervous system can induce motor neuropathy in Familial Amiloidotic Polyneuropethy (FAP) patients. This produces progressive reductions in functional capacity. The only treatment for FAP is a liver transplant, followed by aggressive medication that can affect patients' metabolism. To our knowledge, there are no data on body fat distribution or comparison between healthy and FAP subjects, which may be important for clinical assessment and management of this disease. PURPOSE: To analyze body fat content and distribution between FAP patients and healthy subjects. METHODS: Body fat content and distribution were measured through Double Energy X-ray Densitometry (DXA) in two groups. Group 1 consisted of 43 Familial Amyloidotic Polyneuropathy patients (19 males, 32 + 8 Yrs, and 24 females, 37 + 5 yrs), who had liver transplant less than 2 months before. Group 2 consisted of 18 healthy subjects of similar age (8 males, 36 + 7 yrs, and 10 females, 39 + 5 yrs). RESULTS: Healthy subjects showed higher values than FAP patients for: BMI (24,2+2,3kg/m2 vs 22,3+3,8 kg/m2 respectively, p<0,05), % trunk BF (26,21+8,34kg vs 20,78+9,05kg respectively, p<0,05), % visceral BF (24,43+7,97% vs 19,21+9,30% respectively, p<0,05), % abdominal BF (26,63+8,51% vs 20,63+10,35% respectively, p<0,05) abdominal subcutaneous BF (0,533+0,421kg vs 0,353+0,257kg respectively, p=0,05), abdominal BF/BF ratio (0,09+0,02 vs 0,08+0,02 respectively, p<0,05) and abdominal BF/trunk BF ratio (0,19+0,03 vs 0,17+0,03 respectively, p<0,05). CONCLUSIONS: These results showed that FAP patients soon after liver transplantation exhibited a healthier body fat profile compared to controls. However, fat content and distribution varied widely in FAP subjects, suggesting an individualized approach for assessment and intervention rather than general guidelines. Future research is needed to investigate the long term consequences on body fat following liver transplant in this population.

Comparison of body fat content and distribution of familial amyloidotic polyneuropathy patients versus healthy subjects

The deposition of amyloid fibers at the peripheral nervous system can induce motor neuropathy in Familial Amiloidotic Polyneuropethy (FAP) patients. This produces progressive reductions in functional capacity. The only treatment for FAP is a liver transplant, followed by aggressive medication that can affect patients' metabolism. To our knowledge, there are no data on body fat distribution or comparison between healthy and FAP subjects, which may be important for clinical assessment and management of this disease.