Structure and thermal properties of yttrium alumino-phosphate glasses

The structure and thermal properties of yttrium alumino-phosphate glasses, of nominal composition (Y2O3)(0.31-z)(Al2O3)(z)(P2O5)(0.69) with 0 less than or similar to z less than or similar to 0.31, were studied by using a combination of neutron diffraction, Al-27 and P-31 magic angle spinning nuclear magnetic resonance, differential scanning calorimetry and thermal gravimetric analysis methods. The Vickers hardness of the glasses was also measured. The data are compared to those obtained for pseudo-binary Al2O3-P2O5 glasses and the structure of all these materials is rationalized in terms of a generic model for vitreous phosphate materials in which Y3+ and Al3+ act as modifying cations that bind only to the terminal (non-bridging) oxygen atoms of PO4 tetrahedra. The results are used to help elucidate the phenomenon of rare-earth clustering in phosphate glasses which can be reduced by substituting Al3+ ions for rare-earth R3+ ions at fixed modifier content.

Green-to-red tunable SHG of a quantum-dot laser in a PPKTP waveguide

Quasi-phase-matching is an important and widelyused technique in nonlinear optics enabling efficient frequency up-conversion. However, since its introduction almost half a century ago, this technique is well developed for near infrared (IR) but is intrinsically limited in spectral tunability in the visible range by the strict conditions set by the spatial modulation which compensates the momentum mismatch imposed by the dispersion. Here, we provide a fundamental generalization of quasi-phase-matching based on the utilization of a significant difference in the effective refractive indices of the high- and low-order modes in multimode waveguides. This concept enables to match the period of poling in a very broad wavelength range and opens up a new avenue for an order-ofmagnitude increase in wavelength range for frequency conversion from a single crystal. Using this approach, we demonstrate an all-room-temperature continuous-wave (CW) second harmonic generation (SHG) with over 60 nm tunability from green to red in a periodically-poled potassium titanyl phosphate (PPKTP) waveguide pumped by a single broadly-tunable quantumdot laser diode. © 2012 by Astro, Ltd.

Structure of rare-earth phosphate glasses by neutron diffraction

Neutron diffraction was used to measure the structure of the phosphate glasses RAl0.30P3.05O9.62, where R denotes Dy or Ho, and RAl0.34P3.20O10.04, where R denotes La or Ce. For each glass, isomorphic structures were assumed and difference function methods were employed to separate, essentially, those correlations involving the rare-earth ion, R3+, from the remainder. The ratio of bridging oxygen, OB, to terminal oxygen, OT, atoms in the PO4 tetrahedra was quantified and in both materials R3+ and Al3+ are found to act as network modifying cations which bind to the OT. The R–OT coordination number is 6.7(1) and 7.5(2) for the Dy/Ho and La/Ce glasses respectively.

Narrow-band generation and mode correlations in a short Raman fibre laser

We design a Raman fibre laser with a short cavity providing narrow-band generation. The laser is based on a commercial single-mode fibre (980-HP) span of 12 m length. The laser generates up to 11 W of intracavity power. Even at high generation power, the laser spectrum is narrow (less than 200 pm) - several times narrower than for conventional Raman fibre lasers based on longer fibres. The intensity dynamics reveals indications of mode correlations. © 2014 Astro Ltd.

Structure of dysprosium and holmium phosphate glasses by the method of isomorphic substitution in neutron diffraction

The relative distribution of rare-earth ions R3+ (Dy3+ or Ho3+) in the phosphate glass RAl0.30P3.05O9.62 was measured by employing the method of isomorphic substitution in neutron diffraction and, by taking the role of Al into explicit account, a self-consistent model of the glass structure was developed. The glass network is found to be made from corner sharing PO4 tetrahedra in which there are, on average, 2.32(9) terminal oxygen atoms, OT, at 1.50(1) Å and 1.68(9) bridging oxygen atoms, OB, at 1.60(1) Å. The network modifying R3+ ions bind to an average of 6.7(1) OT and are distributed such that 7.9(7) R–R nearest neighbours reside at 5.62(6) Å. The Al3+ ion also has a network modifying role in which it helps to strengthen the glass through the formation of OT–Al–OT linkages. The connectivity of the R-centred coordination polyhedra in (M2O3)x(P2O5)1−x glasses, where M3+ denotes a network modifying cation (R3+ or Al3+), is quantified in terms of a parameter fs. Methods for reducing the clustering of rare-earth ions in these materials are then discussed, based on a reduction of fs via the replacement of R3+ by Al3+ at fixed total modifier content or via a change of x to increase the number of OT available per network modifying M3+ cation.

Grading and disease management in national screening for diabetic retinopathy in England and Wales

Aims - A National Screening Programme for diabetic eye disease in the UK is in development. We propose a grading and early disease management protocol to detect sight-threatening diabetic retinopathy and any retinopathy, which will allow precise quality assurance at all steps while minimizing false-positive referral to the hospital eye service. Methods - Expert panel structured discussions between 2000 and 2002 with review of existing evidence and grading classifications. Proposals - Principles of the protocol include: separate grading of retinopathy and maculopathy, minimum number of steps, compatible with central monitoring, expandable for established more complex systems and for research, no lesion counting, no ‘questionable’ lesions, attempt to detect focal exudative, diffuse and ischaemic maculopathy and fast track referral from primary or secondary graders. Sight-threatening diabetic retinopathy is defined as: preproliferative retinopathy or worse, sight-threatening maculopathy and/or the presence of photocoagulation. In the centrally reported minimum data set retinopathy is graded into four levels: none (R0), background (R1), preproliferative (R2), proliferative (R3). Maculopathy and photocoagulation are graded as absent (M0, P0) or present (M1, P1). Discussion - The protocol developed by the Diabetic Retinopathy Grading and Disease Management Working Party represents a new consensus upon which national guidelines can be based leading to the introduction of quality-assured screening for people with diabetes.

Structure of lanthanum and cerium phosphate glasses by the method of isomorphic substitution in neutron diffraction

Neutron diffraction was used to measure the total structure factors for several rare-earth ion R3+ (La3+ or Ce3+) phosphate glasses with composition close to RAl0.35P3.24O10.12. By assuming isomorphic structures, difference function methods were employed to separate, essentially, those correlations involving R3+ from the remainder. A self-consistent model of the glass structure was thereby developed in which the Al correlations were taken into explicit account. The glass network was found to be made from interlinked PO4 tetrahedra having 2.2(1) terminal oxygen atoms, OT, at 1.51(1) Angstrom, and 1.8(1) bridging oxygen atoms, OB, at 1.60(1) Angstrom. Rare-earth cations bonded to an average of 7.5(2) OT nearest neighbors in a broad and asymmetric distribution. The Al3+ ion acted as a network modifier and formed OT-A1-OT linkages that helped strengthen the glass. The connectivity of the R-centered coordination polyhedra was quantified in terms of a parameter f(s) and used to develop a model for the dependence on composition of the A1-OT coordination number in R-A1-P-O glasses. By using recent 17 A1 nuclear-magnetic-resonance data, it was shown that this connectivity decreases monotonically with increasing Al content. The chemical durability of the glasses appeared to be at a maximum when the connectivity of the R-centered coordination polyhedra was at a minimum. The relation of f(s) to the glass transition temperature, Tg, was discussed.

Semiconductor saturable absorber mirror passively Q-switched 2.97 μm fluoride fiber laser

A diode-cladding-pumped mid-infrared passively Q-switched Ho3+-doped fluoride fiber laser using a reverse designed broad band semiconductor saturable mirror (SESAM) was demonstrated. Nonlinear reflectivity of the SESAM was measured using an in-house Yb3+-doped mode-locked fiber laser at 1062 nm. Stable pulse train was produced at a slope efficient of 12.1% with respect to the launched pump power. Maximum pulse energy of 6.65 μ J with a pulse width of 1.68 μ s and signal-to-noise ratio (SNR) of ∼50 dB was achieved at a repetition rate of 47.6 kHz and center wavelength of 2.971 μ m. To the best of our knowledge, this is the first 3 μ m region SESAM-based Q-switched fiber laser with the highest average power and pulse energy, as well as the longest wavelength from mid-infrared passively Q-switched fluoride fiber lasers. © 2014 Astro Ltd.

Identification of the relative distribution of rare-earth ions in phosphate glasses

The relative distribution of rare-earth ions R3+ (Dy3+ or Ho3+) in the phosphate glass RAl0.30P3.05O9.62 was measured by employing the method of isomorphic substitution in neutron diffraction. It is found that 7.9(7) R-R nearest neighbors reside at 5.62(6) Angstrom in a network made from interlinked PO4 tetrahedra. Provided that the role of Al is explicitly considered, a self-consistent account of the local matrix atom correlations can be developed in which there are 1.68(9) bridging and 2.32(9) terminal oxygen atoms per phosphorus.

High-efficiency generation in a short random fiber laser

We demonstrate a high-efficiency random lasing in a 850 m span of a phosphosilicate fiber. Random distributed feedback owing to the Rayleigh backscattering in the fiber enables narrowband generation with output power of up to 7.3 W at the Stokes wavelength λS = 1308 nm from 11 Wof the pump power at λP = 1115 nm. The laser demonstrates unique generation efficiency. Near the generation threshold, more than 2 W of output power is generated from only 0.5 W of pump power excess over the generation threshold. At high pump power, the quantum conversion efficiency defined as a ratio of generated and pump photons at the laser output exceeds 100%. Itis explained by the fact that every pump photon is converted into the Stokes photon far from the output fiber end, while the Stokes photons have lower attenuation than the pump photons. © 2014 Astro Ltd.

Photographic Plate Libraries at European Astronomical Observatories

ACM Computing Classification System (1998): J.2.

Bound dissipative-pulse evolution in the all-normal dispersion fiber laser using a 45° tilted fiber grating

The formation and evolution of bound dissipative pulses in the all-normal dispersion Yb-fiber laser based on a novel 45° tilted fiber grating (TFG) are first investigated both numerically and experimentally. Based on the nonlinear polarization rotation technique, the TFG and two polarization controllers (PCs) are exploited for stable self-started passive mode locking. Numerical results show that the formation of bound-state pulses in the all-normal dispersion region is the progress of soliton shaping through the dispersive waves and follows the soliton energy quantization effect. Theoretical and experimental results demonstrate that the formation mechanism of bound-state pulses can be attributed to the high pump strength and effective filter bandwidth. The obtained bound-state dissipative pulses with quasi-rectangular spectral profile have fixed pulse separation as a function of pump power. © 2013 Astro Ltd.

Efficient lasing at near 3μm by a Dy-doped ZBLAN fiber laser pumped at ∼1.1 μm by an Yb fiber laser

Operation of a single-clad Dy 3+-doped ZrF 4-BaF 2-LaF 3-AlF 3-NaF (ZBLAN) fiber laser operating at mid-infrared near 3 μm is presented. The laser is pumped by an Yb 3+-doped silica fiber laser centered at 1088 nm. An output of near 0.1 W with a slope efficiency of up to 23% with respect to absorbed pump power was measured. The laser performance, theoretical modeling and laser spectrum of Dy fiber laser system with respect to various cavity losses are studied. The experimental slope efficiency is more than 4.5 times higher than the previous demonstration, and is 64% of the Stokes efficiency limit. The efficiency was improved by using cavity mirrors of reflectivities of 99 and 50%. The emission central wavelength and spectral width are found to be dependent on the pump power and output coupler, reflectivity. © 2011 by Astro Ltd., published exclusively by WILEY-VCH Verlag GmbH & Co. KGaA.

Generation of 1.7-μJ pulses at 1.55μm by a self-modelocked all-fiber laser with a kilometers-long linear-ring cavity

We report on the record-high pulse energy of nearly 1.7 μJ obtained directly from a self-mode-locked all-fiber erbium laser with a linear-ring cavity owing its extreme elongation up to several kilometers. Specially selected telecommunication fibers, providing large normal net cavity dispersion in the vicinity of 1.55 μm, have been used for this purpose. Along with compensation for polarization instability in the longer linear arm of the cavity, such approach has ensured stable wavebreaking- free mode-locked lasing with an ultra-low pulse repetition rate of 35.1 kHz. © 2010 by Astro Ltd.

Conhecimento da doença renal crônica entre médicos conforme as diretrizes práticas

INTRODUCTION: Chronic kidney disease (CKD) is a global health problem, with increasing prevalence in its terminal stage and one of the factors that can contribute is the failure to recognize the disease and its risk factors. OBJECTIVE: To evaluate the knowledge of medical residents (MR) and medical preceptors (MP) in hospitals in the Federal University of Rio Grande do Norte in Natal-RN - Brazil, on the DRC, based on the policy of the Kidney Disease Improving Global Outcomes (KDIGO ). METHODS: Cross-sectional study where 64 MR (R1 = 32; R2 = 15; R3 = 17) and 63 MP answered a questionnaire divided into seven sessions that addressed aspects of the DRC since the setting up referral to a nephrologist. RESULTS: Only 20 participants (15.7%) reported using any guidelines for the management of CKD. The scores obtained by session were: Definition and classification (46.1 ± 47.8); Risk factors (70.5 ± 27.9); Laboratory evaluation (58.2 ± 8.8); Clinical action plan (57.6 ± 19.9); Reduction in proteinuria (68.3 ± 15.0); Complications (64.8 ± 19.9); Referral to a nephrologist (73.0 ± 44.6). There was a statistically significant difference between the knowledge of MR and MP in the sessions: Laboratory evaluation (MR 61.5 ± 8.4 vs 54.8 ± 7.9 MP; p <0.001); Reduction in proteinuria (73.1 ± 11.4 vs MR MP 63.5 ± 16.7; p <0.001) and Referral to a nephrologist (MR 81.2 ± 39.3 vs 64.5 ± 48.2 MP; p = 0.035). Among the MR, the R2 obtained the best score (63.9 ± 22.6 vs R1 R2 R3 71.9 ± 17.2 vs 63.5 ± 22.5, p = 0.445). It identified a low percentage of success of the doctors on the definition of CKD (MP = 46%; R1 = 40.6%; R2 = 60%; R3 = 52.9%; p = 0.623) and classification (MP = 34.9%; R1 = 53.1%, R2 = 60%; R3 = 52.9%; p = 0.158). CONCLUSION: The study showed that most doctors do not use any guidelines for clinical management of CKD and that there are gaps in knowledge on the subject, even among physicians who work in the university environment. In this sense, we propose the realization of mini-workshops for participants and students from boarding UFRN, using Case-Based Learning Strategy (CBL), with small group discussion, to strengthen the incorporation of CKD guidelines in undergraduate teaching and in clinical medical practice in general.