Airborne simulation for the SST.

Cover title.

Arsenic speciation in the urine and hair of individuals exposed to airborne arsenic through coal-burning in Guizhou, PR China

The extent of exposure of residents of Changqing (Guizhou, PR China) to arsenic through coal-burning was investigated. Despite the low coal-arsenic content (56.3 +/- 42.5 mg As kg(-1)) when compared with coals collected at different location and times from the same province, more than 30% of the study subjects have shown symptoms of arsenicosis. Coal, urine, hair, and water samples were collected in mid-September 2001 and analysed for arsenic. The average urinary and hair-arsenic concentrations in the exposed subjects were 71.4 +/- 37.1 mug As g(-1) creatinine (control 41.6 +/- 12.1) and 7.99 +/- 8.16 mg kg(-1), respectively. A positive correlation between the hair and urinary-arsenic concentration (R-2 = 0.601) was found. There was no significant difference between females and males for both urinary and hair-arsenic concentrations. Females were found to have a higher dimethylarsinic acid but lower percentages of inorganic arsenic and monomethylarsonic acid in their urine than males. (C) 2002 Elsevier Science Ireland Ltd. All rights reserved.

Quantitative trends in airborne loads of Celtis sinensis pollen and associations with meteorological variables in a subtropical Australian environment

Celtis sinensis is an introduced plant species to the southeastern region of Queensland that has had a destructive affect on indigenous plant Communities and its pollen has been identified as an allergen Source. Pollen belonging to C. sinensis was sampled during a 5-year (June 1994-May 1999) atmospheric pollen-monitoring programme in Brisbane, Australia, using a Burkard 7-day spore trap. The seasonal incidence of airborne C. sinensis pollen (CsP) in Brisbane occurred over a brief period each year during spring (August-September), while peak concentrations were restricted to the beginning of September. individual CsP seasons were heterogeneous with daily counts within the range 1-10 grains m(-3) on no more than 60 sampling days; however, smaller airborne concentrations of CsP were recorded out of each season. Correlation co-efficients were significant each year for temperature (p0.05) and relative humidity (p>0.05). A significant relationship (r(2)=0.81, p=0.036) was established between the total CsP count and pre-seasonal average maximum temperature; however, periods of precipitation (>2mm) were demonstrated to significantly lower the daily concentrations of CsP from the atmosphere. Given the environmental and clinical significance of CsP and its prevalence in the atmosphere of Brisbane, a Clinical population-based Study is required to further understand the pollen's importance as a seasonal sensitizing source in this region.

A practical tool to identify water bodies with potential for mosquito habitat under mangrove canopy: Large-scale airborne scanning in the thermal band

We address the practical issue of using thermal image data without adjustment or calibration for projects which do not require actual temperatures per se. Large scale airborne scanning in the thermal band at 8.5–13 μm was obtained for a mangrove and salt marsh in subtropical eastern Australia. For open sites, the raw image values were strongly positively correlated with ground level temperatures. For sites under mangrove canopy cover, image values indicated temperatures 2–4°C lower than those measured on the ground. The raw image was useful in identifying water bodies under canopy and has the potential for locating channel lines of deeper water. This could facilitate modification to increase flushing in the system, thereby reducing mosquito larval survival.

Mapping mosquito breeding habitats (water) under mangrove canopy: contribution from airborne thermal scanning

Proceedings of the 11th Australasian Remote Sensing and Photogrammetry Conference

The geometric correction and registration of airborne line-scanned imagery for temporal thermal studies

This thesis begins by providing a review of techniques for interpreting the thermal response at the earth's surface acquired using remote sensing technology. Historic limitations in the precision with which imagery acquired from airborne platforms can be geometrically corrected and co-registered has meant that relatively little work has been carried out examining the diurnal variation of surface temperature over wide regions. Although emerging remote sensing systems provide the potential to register temporal image data within satisfactory levels of accuracy, this technology is still not widely available and does not address the issue of historic data sets which cannot be rectified using conventional parametric approaches. In overcoming these problems, the second part of this thesis describes the development of an alternative approach for rectifying airborne line-scanned imagery. The underlying assumption that scan lines within the imagery are straight greatly reduces the number of ground control points required to describe the image geometry. Furthermore, the use of pattern matching procedures to identify geometric disparities between raw line-scanned imagery and corresponding aerial photography enables the correction procedure to be almost fully automated. By reconstructing the raw image data on a truly line-by-line basis, it is possible to register the airborne line-scanned imagery to the aerial photography with an average accuracy of better than one pixel. Providing corresponding aerial photography is available, this approach can be applied in the absence of platform altitude information allowing multi-temporal data sets to be corrected and registered.

Identification of industrial sources of airborne heavy metal pollution in urban areas

The research examines the deposition of airborne particles which contain heavy metals and investigates the methods that can be used to identify their sources. The research focuses on lead and cadmium because these two metals are of growing public and scientific concern on environmental health grounds. The research consists of three distinct parts. The first is the development and evaluation of a new deposition measurement instrument - the deposit cannister - designed specifically for large-scale surveys in urban areas. The deposit cannister is specifically designed to be cheap, robust, and versatile and therefore to permit comprehensive high-density urban surveys. The siting policy reduces contamination from locally resuspended surface-dust. The second part of the research has involved detailed surveys of heavy metal deposition in Walsall, West Midlands, using the new high-density measurement method. The main survey, conducted over a six-week period in November - December 1982, provided 30-day samples of deposition at 250 different sites. The results have been used to examine the magnitude and spatial variability of deposition rates in the case-study area, and to evaluate the performance of the measurement method. The third part of the research has been to conduct a 'source-identification' exercise. The methods used have been Receptor Models - Factor Analysis and Cluster Analysis - and a predictive source-based deposition model. The results indicate that there are six main source processes contributing to deposition of metals in the Walsall area: coal combustion, vehicle emissions, ironfounding, copper refining and two general industrial/urban processes. |A source-based deposition model has been calibrated using facctorscores for one source factor as the dependent variable, rather than metal deposition rates, thus avoiding problems traditionally encountered in calibrating models in complex multi-source areas. Empirical evidence supports the hypothesised associatlon of this factor with emissions of metals from the ironfoundry industry.

Geometric spectral accuracy of airborne remote sensing

DUE TO COPYRIGHT RESTRICTIONS ONLY AVAILABLE FOR CONSULTATION AT ASTON UNIVERSITY LIBRARY AND INFORMATION SERVICES WITH PRIOR ARRANGEMENT